Synthesis and electrochemical properties of LiV3O8 phase

Lithium vanadium oxide was synthesized by a new method in which LiOH, V₂O₅ and NH₄OH were used as the starting materials to synthesize a precursor containing Li and V, and then obtain the resulting product by calcining the precursor. The LiV₃O₈ compound prepared by this synthesis method gave a good charge-discharge and cycle performance. A specific capacity of 258 mAh/g is obtained in the range of 1.8−4.0 V in the first cycle and 247 mAh/g in the eighth cycle.     

Preparation and electrochemical properties of lamellar MnO2 for supercapacitors

Lamellar birnessite-type MnO₂ materials were prepared by changing the pH of the initial reaction system via hydrothermal synthesis. The interlayer spacing of MnO₂ with a layered structure increased gradually when the initial pH value varied from 12.43 to 2.81, while the MnO₂, composed of α-MnO₂ and γ-MnO₂, had a rod-like structure at pH 0.63. Electrochemical studies indicated that the specific capacitance of birnessite-type MnO₂ was much higher than that of rod-like MnO₂ at high discharge current densities due to the lamellar structure with fast intercalation/deintercalation of protons and high utilization of MnO₂. The initial specific capacitance of MnO₂ prepared at pH 2.81 was 242.1 F g⁻¹ at 2 mA cm⁻² in 2 mol L⁻¹ (NH₄)₂SO₄ aqueous electrolyte. The capacitance increased by about 8.1% of initial capacitance after 200 cycles at a current density of 100 mA cm⁻².     

Large-scale fabrication of H2(H2O)Nb2O6 and Nb2O5 hollow microspheres

Hollow micro-sized H₂(H₂O)Nb₂O₆ spheres constructed by nanocrystallites have been successfully synthesized via a bubble-template assisted hydrothermal process. In the reaction process, H₂O₂ acts as a bubble generator and plays a key role in the formation of the hollow structure. An in situ bubble-template mechanism has been proposed for the possible formation of the hollow structure. The spherelike assemblies of these H₂(H₂O)Nb₂O₆ nanoparticles have been transformed into their corresponding pseudohexagonal phase Nb₂O₅ through a moderate annealing dehydration process without destroying the hierarchical structure. Optical properties of the as-prepared hollow spheres were investigated. It is exciting that the absorption edge of the hollow Nb₂O₅ microspheres shifts about 18 nm to the violet compared with bulk powders in the UV/vis spectra, indicating its superior optical properties.     

Synthesis, characterization and photocatalytic properties of nanosized Bi2WO6, PbWO4 and ZnWO4 catalysts

Nanosized Bi₂WO₆, PbWO₄ and ZnWO₄ photocatalysts were synthesized by a mild hydrothermal crystallization process. The physical and photophysical properties of the catalysts were characterized by X-ray diffractometry, Brunauer-Emmet-Teller surface area and porosity measurements, transmission electron microscopy, Raman spectra, and diffused reflectance spectroscopy. The rhodamine-B photodegradation in aqueous medium was employed as a probe reaction to test the photoactivities of the as-prepared samples under four irradiation wavelengths. Bi₂WO₆ not only presented the photocatalytic activity in the wide spectral scope, including UV and visible light but also exhibited the strong photosensitized capability to transform RhB under visible light irradiation (λ > 490 nm). ZnWO₄ only displayed relatively high photoactivity under UV irradiation. However, PbWO₄ showed poor photoactivity under any light irradiation. On the basis of the calculated density functional theory (DFT), the photocatalytic mechanisms were discussed.     

Preparation and properties of negative thermal expansion Zr2WP2O12 ceramics

Using solid-state reaction method, Zr₂WP₂O₁₂ powder was synthesized for this study. The optimum heating condition was 1200 °C for 4 h. The obtained powder was compacted and sintered. The relative density of the Zr₂WP₂O₁₂ ceramics with no sintering additive was 60%. That of samples sintered with more than 0.5 mass% MgO was about 97%. The average grain size (D₅₀), as estimated from the polished surface of a sample sintered at 1200 °C for 4 h was about 1 μm. The obtained ceramics showed a negative thermal expansion coefficient of about −3.4 × 10⁻⁶ °C⁻¹. Young's modulus, Poisson's ratio, three-point bending strength, Vickers microhardness, and fracture toughness of the obtained ceramics were, respectively, 74 GPa, 0.25, 113 ± 13 MPa, 4.4 GPa and 2.3 MPa m^1/2.     

CuBi2O4 single crystal nanorods prepared by hydrothermal method: Growth mechanism and optical properties

The synthesis of copper bismuth oxide (CuBi₂O₄) nanorods with single crystal structure by hydrothermal method is first reported here. The prepared CuBi₂O₄ nanorods are characterized by X-ray diffractometer, scanning electron microscopy, transmission electron microscopy (TEM) and high resolution TEM. It is found that the concentration of reagent cupric acetate has strong effect on the purity and microstructure of the prepared samples. The growth process is investigated in detail. It is proposed that the nanorods are evolved from spherical particles with oriented attachment mechanism followed by dissolution-splitting process. The optical properties of the samples are detected by UV-vis spectrometer and photoluminescence spectrometer and exhibit strong dependence on surface defect states and microstructure feature, which is mainly determined by preparation conditions.     

Physical,photoelectrochemical properties of CuIn3Se5 and relevance for hydrogen production

CuIn₃Se₅, prepared by the fusion technique crystallizes in the P-chalcopyrite structure and exhibits n-type conduction ascribed to indium excess. The electrical conductivity follows an Arrhenius-type law with activation energy of 0.35 eV and an electron mobility of 10⁻⁴ cm² V⁻¹ s⁻¹ in conformity with small polaron hopping. The optical gap (1.19 eV), determined from the diffuse reflectance spectrum, is properly matched to the sun spectrum. CuIn₃Se₅ is chemically stable and a corrosion rate of only 1.2 μmol year⁻¹ is found at neutral pH. The slope and the intercept to C⁻² = 0 of the Mott Schottky plot gives respectively an electron density of 3.75 × 10¹⁶ cm⁻³ and a flat band potential of −0.22 V_SCE. The conduction band (−0.74 V_SCE) therefore lies below the potential of H₂O/H₂ couple and as application, H₂ photo-production is successfully achieved over CuIn₃Se₅. The best performance is obtained in S₂O₃²⁻ solution (10⁻² M, pH ∼ 7) with an evolution rate of 0.54 mL g⁻¹ min⁻¹. The conversion efficiency (0.13%) is due to the formation of small depletion width (230 nm) and a large diffusion length compared to a very large penetration depth (∼1 μm). Attempts have been made to improve the photoactivity and the hetero-system CuIn₃Se₅/WO₃ is compared favorably with respect to CuIn₃Se₅. The photoactivity is ascribed to electrons transfer from the sensitizer CuIn₃Se₅-conduction band (CB), acting as electrons pump, to WO₃-CB (−0.4 V_SCE) resulting in the enhanced water reduction.     

Influence of fuels on the morphology of undoped Y3Al5O12 and photoluminescence of Y3Al5O12:Eu prepared by a combustion method

Undoped and Eu-doped yttrium aluminum garnet nano-powders were prepared by a facile combustion method with citric acid/ethylene diamine tetraacetic acid (EDTA) as fuels and nitrates as oxidizers. The precursors and powders calcined at 1030 °C were investigated using thermogravimetric (TG), differential thermal analysis (DTA), X-ray diffraction (XRD), scanning electron microscope (SEM), and Brunauer-Emmett-Teller (BET) surface area measurements. It was found that the powders could be indexed with a garnet structure. The grains were in shape of hemispherical with sizes between 60 nm and 100 nm. With decreasing the citric acid/EDTA ratio, the crystallite size decreased steadily and the specific surface area increased. Investigations of photoluminescence (PL) revealed that as-synthesized YAG:Eu³⁺ phosphor samples exhibited an orange emission band with a main peak at 591 nm under the excitation of 394 nm. As citric acid amounts increased, the quality of crystallinity became higher and the luminescent properties were monotonously enhanced.     

High sensitivity chlorine gas sensors using CdIn2O4 thick film prepared by co-precipitation method

Gas-sensing properties to dilute Cl₂ have been investigated for CdIn₂O₄ thick film sensors prepared by co-precipitation method. Cadmium nitrate and indium nitrate were mixed in de-ionized water. The 0.1 M NaOH was added to the mixed solution. The co-precipitate obtained was washed, filtered, dried, and calcined at 600-900 °C for 4 h. The CdIn₂O₄ sensor prepared using the powder calcined at 600 °C showed high sensitivity (S=R_g/R_a) to dilute Cl₂ at 250 °C. In particular, the CdIn₂O₄ sensor showed the sensitivity as high as 1200 even to 0.2 ppm Cl₂. The crystal structure and surface morphology were examined by means of X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively.     

Preparation of Y2O3-Al2O3-SiO2 glasses by combustion synthesis melt-casting under high gravity

Y₂O₃-Al₂O₃-SiO₂ glasses were prepared by combustion synthesis melt-casting under high gravity. The properties of the glasses strongly depended on the starting compositions and preparation conditions. With a higher SiO₂ content in the starting compositions, the glass-forming ability of the melt was improved, but the density and hardness of the prepared glasses decreased. Crystallization occurred more frequently for larger samples and by using quartz crucibles instead of graphite ones. By increasing the high-gravity factors, both the density and hardness of the samples were improved. It is proposed that enhancing the high-gravity field facilitates the removal of bubbles from the melt.     

Synthesis and characterization of Bi2Fe4O9 powders

Bi₂Fe₄O₉ have been successfully prepared using ethylenediaminetetraacetic (EDTA) acid as a chelating agent and ethylene glycol as an esterification agent. Heating of a mixed solution of EDTA, ethylene glycol, and nitrates of iron and bismuth at 140 °C produced a transparent polymeric resin without any precipitation, which after pyrolysis at 250 °C was converted to a powder precursor for Bi₂Fe₄O₉. The precursors were heated at 400–800 °C in air to obtain Bi₂Fe₄O₉ powder and differential scanning calorimetry (DSC), thermogravimetric (TG), Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM) techniques were used to characterize the precursors and the derived oxide powders. XRD analysis showed that well-crystallized and single-phase Bi₂Fe₄O₉ with orthorhombic symmetry was obtained at 700 °C for 2 h and BiFeO₃ and Fe₂O₃/FeCO₃ were intermediate phases before the formation of Bi₂Fe₄O₉. Bi₂Fe₄O₉ powders show weak ferromagnetism at room temperature.     

Controllable synthesis and magnetic property of BiMn2O5 crystals

Uniform submicron BiMn₂O₅ particles were prepared via a facile one-step hydrothermal route at low temperature. Bi(NO₃)₃, MnCl₂·4H₂O and KMnO₄ were used as starting materials; KOH as a pH adjustor and also as a mineralizer. Single-crystalline orthorhombic BiMn₂O₅ sample with controllable morphology was obtained. The microstructure strongly depends on the molar ratio of the starting materials, KOH concentration and reaction temperature. X-ray photoelectron spectroscopy shows the existence of Mn⁴⁺ state. Magnetic measurement indicates Néel temperature T_N at 44 K. The susceptibility above T_N obeys the Curie-Weiss law, χ = C/(T − θ), with θ = −350 K. The effective paramagnetic moment μ_eff = 4.66 μ_B/Mn, demonstrating the coexistence of mixed Mn³⁺ and Mn⁴⁺ valences.     

Microwave-hydrothermal synthesis of γ-Fe2O3 nanoparticles and their magnetic properties

Nanosized γ-Fe₂O₃ is synthesized by the microwave-hydrothermal method. Powder X-ray diffraction and transmission electron microscopic studies showed that the average particle size is 10 nm. Magnetic studies reveal that the γ-Fe₂O₃ nanoparticles are superparamagnetic at room temperature, with a superparamagnetic blocking temperature of 200 K. The magnetic characteristics of the nanoparticles indicate their strongly interacting nature.     

Preparation and ethanol sensing properties of the superstructure SnO2/ZnO composite via alcohol-assisted hydrothermal route

Self-assembled superstructure of SnO₂/ZnO composite was synthesized by using alcohol-assisted hydrothermal method gas sensing properties of the material were investigated by using a static test system. The structure and morphology of the products were characterized by X-ray diffraction (XRD) and field-emission scanning electron microscope (FE-SEM). The diameter of the SnO₂ nanorods was about 40 nm with a length of about 300 nm, SnO₂ nanorods and ZnO nanosheets interconnect each other to form a superstructure. The gas sensing properties of superstructure SnO₂/ZnO composite with different content of ZnO were investigated. Furthermore, the superstructure SnO₂/ZnO composite sensor is characterized at different operating temperatures and its long-term stability in response to ethanol vapor is tested over a period of 3 months.     

Synthesis of polycrystalline SnO2 nanotubes on carbon nanotube template for anode material of lithium-ion battery

Polycrystalline tin oxide nanotubes have been prepared by a layer-by-layer technique on carbon nanotubes template. Firstly, the surface of carbon nanotubes was modified by polyelectrolyte. Then, a uniform layer of tin oxide nanoparticles was formed on the positive charged surface of carbon nanotubes via a redox process. At last, the polycrystalline tin oxide nanotubes were synthesized after calcination at 650 °C in air for 3 h. The as-synthesized polycrystalline nanotubes with large surface area exhibit finer lithium storage capacity and cycling performance, which shows the potentially interesting application in lithium-ion battery.     

Microwave synthesis of nanocrystalline Sb2S3 and its electrochemical properties

Nanocrystalline antimony trisulfide (Sb₂S₃) was successfully synthesized via microwave irradiation by the reaction of antimony trichloride (SbCl₃) and thiourea (CS(NH₂)₂) with PVP as the surfactant. The samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and high resolution TEM (HRTEM). XRD results show that the as-prepared sample is orthorhombic-phase Sb₂S₃. TEM image of the as-prepared Sb₂S₃ shows the rod-like structure. HRTEM image indicates that rodbundles of Sb₂S₃ consists of a number nanorods with the diameter ranging from 30 nm to 50 nm. Detailed HRTEM image demonstrates the preferential direction growth of the Sb₂S₃ nanorods. The electrochemical properties of Sb₂S₃ were primarily investigated by constant current charge/discharge cycling tests in lithium hexafluorophosphate (LiPF₆) solution. The possible electrochemical reaction mechanism was explained. The results indicate that the nanocrystalline Sb₂S₃ shows potential application in the field of the electrode materials.     

Synthesis and magnetic properties of (Ba,Bi)1.54Rh8O16 hollandite

The synthesis, structure and electrical and magnetic properties of (Ba,Bi)_1.54Rh₈O₁₆ hollandite are discussed. The addition of Bi stabilizes the Ba-Rh hollandite, otherwise not found under our synthesis conditions. The compound crystallizes in the monoclinic space group I2/m, a = 9.425(5) Å, b = 10.425(4) Å, c = 3.160(1) Å, γ = 94.11(5). Electron diffraction and structure imaging show that the (Ba,Bi) columns along the tunnels are incommensurate with the Rh₈O₁₆ framework, and analysis of the electron diffraction and elemental analysis allow the formula to be determined as Ba_1.21Bi_0.33Rh₈O₁₆. The compound shows Curie-Weiss paramagnetism, and we compare its susceptibility to that of Rh₂O₃. Polycrystalline samples show a negative dρ/dT between 0.3 and 300 K. No superconductivity is observed down to 0.3 K.     

Low temperature synthesis and characterization of SnTa2O6

Sn(II)Ta₂O₆ is well known as the mineral Thoreaulite, but attempts to prepare it by direct combination of SnO and Ta₂O₅ fail. SnTa₂O₆ has now been synthesized by reacting SnCl₂ with KTaO₃ at 673 K under an inert atmosphere. Although a reported structure determination of SnTa₂O₆ indicated an acentric space group, our second harmonic generation (SHG) studies indicate that SnTa₂O₆ is centrosymmetric as is the case for isostructural SnNb₂O₆.     

Factors affecting CO oxidation over nanosized Fe2O3

Nanocrystallite iron oxide powders with different crystallite sizes were prepared by co-precipitation route. The prepared powders with crystallite size 75, 100 and 150 nm together with commercial iron oxide (250 nm) were tested for the catalytic oxidation of CO to CO₂. The influence of different factors as crystallite size, catalytic temperature and weight of catalyst on the rate of catalytic reaction was investigated using advanced quadrupole mass gas analyzer system. It can be reported that the rate of conversion of CO to CO₂ increased by increasing catalytic temperature and decreasing crystallite size of the prepared powders. The experimental results show that nanocrystallite iron oxide powders with crystallite size 75 nm can be recommended as a promising catalyst for CO oxidation at 500 °C where 98% of CO is converted to CO₂. The mechanism of the catalytic oxidation reaction was investigated by comparing the CO catalytic oxidation data in the absence and presence of oxygen. The reaction which was found to be first order with respect to CO is probably proceeded by adsorption mechanism where the reactants are adsorbed on the surface of the catalyst with breaking OO bonds, then CO pick up the dissociated O atom forming CO₂.     

Preparation of polycrystalline BaTi2O5 by pressureless sintering

Polycrystalline BaTi₂O₅ (BT₂) was prepared by pressureless sintering in air using BaCO₃ and TiO₂ as starting materials. XRD results of the calcined powder showed BaCO₃ and TiO₂ reacted completely after being calcined above 950 °C, showing a mixture of BaTiO₃ (BT), BT₂, BaTi₄O₉ and Ba₄Ti₁₃O₃₀. A small amount of ZrO₂ (less than 0.1 wt%) was effective to prepare BT₂ in a single phase and the second phase of BT and B₆T₁₇ increased with ZrO₂ content. BT₂ sintered body in a single phase was obtained at 1175-1300 °C when ZrO₂ content was 0.08 wt%. The maximum permittivity of BT₂ sintered body was 340 at the Curie temperature (T_c) of 463 °C and the frequency of 100 kHz.