Tensile Behavior of Intercritically Annealed 10 pct Mn Multi-phase Steel

The exceptional elongation obtained during tensile testing of intercritically annealed 10 pct Mn steel, with a two phase ferrite–austenite microstructure at room temperature, was investigated. The austenite phase exhibited deformation-twinning and strain-induced transformation to martensite. These two plasticity-enhancing mechanisms occurred in succession, resulting in a high rate of work hardening and a total elongation of 65 pct for a tensile strength of 1443 MPa. A constitutive model for the tensile behavior of the 10 pct Mn steel was developed using the Kocks–Mecking hardening model.     

Annealing Temperature Dependence of the Tensile Behavior of 10 pct Mn Multi-phase TWIP-TRIP Steel

In the present study, the relationship between the microstructure and the mechanical properties of Fe-10 pct Mn-3 pct Al-2 pct Si-0.3 pct C multi-phase steel was investigated. The 10 pct Mn multi-phase steel exhibits a combination of high tensile strength and enhanced ductility resulting from deformation-twinning and strain-induced transformation occurring in succession. A pronounced intercritical annealing temperature dependence of the tensile behavior was observed. The annealing temperature dependence of the retained austenite volume fraction, composition, and the grain size was analyzed experimentally, and the effect of the microstructural parameters on the kinetics of mechanical twinning and strain-induced martensite formation was quantified. A dislocation density-based constitutive model was developed to predict the mechanical properties of 10 pct Mn multi-phase steel. The model also allows for the determination of the critical strain for dynamic strain aging effect.     

Third Generation 0.3C-4.0Mn Advanced High Strength Steels Through a Dual Stabilization Heat Treatment: Austenite Stabilization Through Paraequilibrium Carbon Partitioning

In excess of 30 vol. pct austenite can be retained in 0.3C-4.0Mn steels subjected to a dual stabilization heat treatment (DSHT) schedule—a five stage precisely controlled cooling schedule that is a variant of the quench and partition process. The temperature of the second quench (stage III) in the DSHT process plays an essential role in the retained austenite contents produced at carbon-partitioning temperatures of 723 K or 748 K (450° C or 475 °C) (stage IV). A thermodynamic model successfully predicted the retained austenite contents in heat-treated steels, particularly for a completely austenitized material. The microstructure and mechanical behavior of two heat-treated steels with similar levels of retained austenite (~30 vol. pct) were studied. Optimum properties—tensile strengths up to 1650 MPa and ~20 pct total elongation—were observed in a steel containing 0.3C-4.0Mn-2.1Si, 1.5 Al, and 0.5 Cr.     

Evaluating the Superplastic Flow of a Magnesium AZ31 Alloy Processed by Equal-Channel Angular Pressing

Experiments show that the magnesium AZ31 (Mg-3 pct Al-1 pct Zn) alloy exhibits excellent superplastic properties at 623 K (350 °C) after processing by equal-channel angular pressing using a die with a channel angle of 135 deg and a range of decreasing processing temperatures from 473 K to 413 K (200 °C to 140 °C). A maximum elongation to failure of ~1200 pct was achieved in this alloy at a tensile strain rate of 1.0 × 10^?4 s^?1. Microstructural inspection showed evidence for cavity formation and grain growth during tensile testing with the grain growth leading to significant strain hardening. An examination of the experimental data shows that grain boundary sliding is dominant during superplastic flow. Furthermore, a comprehensive review of the present results and extensive published data for the AZ31 alloy shows the exponent of the inverse grain size is given by p ≈ 2 which is consistent with grain boundary sliding as the rate-controlling flow mechanism.     

Effect of Continuous Galvanizing Heat Treatments on the Microstructure and Mechanical Properties of High Al-Low Si Transformation Induced Plasticity Steels

Heat treatments were performed using an isothermal bainitic transformation (IBT) temperature compatible with continuous hot-dip galvanizing on two high Al–low Si transformation induced plasticity (TRIP)-assisted steels. Both steels had 0.2 wt pct C and 1.5 wt pct Mn; one had 1.5 wt pct Al and the other had 1 wt pct Al and 0.5 wt pct Si. Two different intercritical annealing (IA) temperatures were used, resulting in intercritical microstructures of 50 pct ferrite (α)-50 pct austenite (γ) and 65 pct α-35 pct γ. Using the IBT temperature of 465 °C, five IBT times were tested: 4, 30, 60, 90, and 120 seconds. Increasing the IBT time resulted in a decrease in the ultimate tensile strength (UTS) and an increase in the uniform elongation, yield strength, and yield point elongation. The uniform elongation was higher when using the 50 pct α-50 pct γ IA temperature when compared to the 65 pct α-35 pct γ IA temperature. The best combinations of strength and ductility and their corresponding heat treatments were as follows: a tensile strength of 895 MPa and uniform elongation of 0.26 for the 1.5 pct Al TRIP steel at the 50 pct γ IA temperature and 90-second IBT time; a tensile strength of 880 MPa and uniform elongation of 0.27 for the 1.5 pct Al TRIP steel at the 50 pct γ IA temperature and 120-second IBT time; and a tensile strength of 1009 MPa and uniform elongation of 0.22 for the 1 pct Al-0.5 pct Si TRIP steel at the 50 pct γ IA temperature and 120-second IBT time.     

Effects of Mn Addition on Tensile and Charpy Impact Properties in Austenitic Fe-Mn-C-Al-Based Steels for Cryogenic Applications

Effects of Mn addition (17, 19, and 22 wt pct) on tensile and Charpy impact properties in three austenitic Fe-Mn-C-Al-based steels were investigated at room and cryogenic temperatures in relation with deformation mechanisms. Tensile strength and elongation were not varied much with Mn content at room temperature, but abruptly decreased with decreasing Mn content at 77 K (?196 °C). Charpy impact energies at 273 K (0 °C) were higher than 200 J in the three steels, but rapidly dropped to 44 J at 77 K (?196 °C) in the 17Mn steel, while they were higher than 120 J in the 19Mn and 22Mn steels. Although the cryogenic-temperature stacking fault energies (SFEs) were lower by 30 to 50 pct than the room-temperature SFEs, the SFE of the 22Mn steel was situated in the TWinning-induced plasticity regime. In the 17Mn and 19Mn steels, however, α′-martensites were formed by the TRansformation-induced plasticity mechanism because of the low SFEs. EBSD analyses along with interrupted tensile tests at cryogenic temperature showed that the austenite was sufficiently deformed in the 19Mn steel even after the formation of α′-martensite, thereby leading to the high impact energy over 120 J.     

Effect of Nitrogen Content on Grain Refinement and Mechanical Properties of a Reversion-Treated Ni-Free 18Cr-12Mn Austenitic Stainless Steel

Martensite reversion treatment was utilized to obtain ultrafine grain size in Fe-18Cr-12Mn-N stainless steels containing 0 to 0.44 wt pct N. This was achieved by cold rolling to 80 pct reduction followed by reversion annealing at temperatures between 973 K and 1173 K (700 °C and 900 °C) for 1 to 10⁴ seconds. The microstructural evolution was characterized using both transmission and scanning electron microscopes, and mechanical properties were evaluated using hardness and tensile tests. The steel without nitrogen had a duplex ferritic-austenitic structure and the grain size refinement remained inefficient. The finest austenitic microstructure was achieved in the steels with 0.25 and 0.36 wt pct N following annealing at 1173 K (900 °C) for 100 seconds, resulting in average grain sizes of about 0.240 ± 0.117 and 0.217 ± 0.73 µm, respectively. Nano-size Cr₂N precipitates observed in the microstructure were responsible for retarding the grain growth. The reversion mechanism was found to be diffusion controlled in the N-free steel and shear controlled in the N-containing steels. Due to a low fraction of strain-induced martensite in cold rolled condition, the 0.44 wt pct N steel displayed relatively non-uniform, micron-scale grain structure after the same reversion treatment, but it still exhibited superior mechanical properties with a yield strength of 1324 MPa, tensile strength of 1467 MPa, and total elongation of 17 pct. While the high yield strength can be attributed to strengthening by nitrogen alloying, dislocation hardening, and slight grain refinement, the moderate strain-induced martensitic transformation taking place during tensile straining was responsible for enhancement in tensile strength and elongation.     

Austenitic Nickel- and Manganese-Free Fe-15Cr-1Mo-0.4N-0.3C Steel: Tensile Behavior and Deformation-Induced Processes between 298 K and 503 K (25 °C and 230 °C)

The high-temperature austenite phase of a high-interstitial Mn- and Ni-free stainless steel was stabilized at room temperature by the full dissolution of precipitates after solution annealing at 1523 K (1250 °C). The austenitic steel was subsequently tensile-tested in the temperature range of 298 K to 503 K (25 °C to 230 °C). Tensile elongation progressively enhanced at higher tensile test temperatures and reached 79 pct at 503 K (230 °C). The enhancement at higher temperatures of tensile ductility was attributed to the increased mechanical stability of austenite and the delayed formation of deformation-induced martensite. Microstructural examinations after tensile deformation at 433 K (160 °C) and 503 K (230 °C) revealed the presence of a high density of planar glide features, most noticeably deformation twins. Furthermore, the deformation twin to deformation-induced martensite transformation was observed at these temperatures. The results confirm that the high tensile ductility of conventional Fe-Cr-Ni and Fe-Cr-Ni-Mn austenitic stainless steels may be similarly reproduced in Ni- and Mn-free high-interstitial stainless steels solution annealed at sufficiently high temperatures. The tensile ductility of the alloy was found to deteriorate with decarburization and denitriding processes during heat treatment which contributed to the formation of martensite in an outermost rim of tensile specimens.     

Mechanical Behaviors of Ultrafine-Grained 301 Austenitic Stainless Steel Produced by Equal-Channel Angular Pressing

The technique of equal-channel angular pressing (ECAP) was used to refine the microstructure of an AISI 301 austenitic stainless steel (SS). An ultrafine-grained (UFG) microstructure consisting mainly of austenite and a few martensite was achieved in 301 steel after ECAP processing for four passes at 523 K (250 °C). By submitting the as-ECAP rods to annealing treatment in the temperature range from 853 K to 893 K (580 °C to 620 °C) for 60 minutes, fully austenitic microstructures with grain sizes of 210 to 310 nm were obtained. The uniaxial tensile tests indicated that UFG 301 austenitic SS had an excellent combination of high yield strength (>1.0 GPa) and high elongation-to-fracture (>30 pct). The tensile stress–strain curves exhibited distinct yielding peak followed by obvious Lüders deformation. Measurements showed that Lüders elongation increased with an increase in strength as well as a decrease in grain size. The microstructural changes in ultrafine austenite grains during tensile deformation were tracked by X-ray diffraction and transmission electron microscope. It was found that the strain-induced phase transformation from austenite to martensite took place soon after plastic deformation. The transformation rate with strain and the maximum strain-induced martensite were promoted significantly by ultrafine austenite grains. The enhanced martensitic transformation provided extra strain-hardening ability to sustain the propagation of Lüders bands and large uniform plastic deformation. During tensile deformation, the Lüders bands and martensitic transformation interacted with each other and made great contribution to the excellent mechanical properties in UFG austenitic SS.     

Effect of Annealing Temperature on Microstructure and Mechanical Properties of Bulk 316L Stainless Steel with Nano- and Micro-crystalline Dual Phases

Microstructures and mechanical properties of 316L stainless steels with dual phases austenite prepared by an aluminothermic reaction casting were explored. It is found that the steels consist of nano- and micro-crystalline austenite phases, a little δ ferrite and contaminations. Before and after annealing at 1073 K and 1273 K (800 °C and 1000 °C), average grain sizes of the nanocrystalline austenite phase are about 32, 31, 38 nm, respectively. Tensile strength increases first from 371 to 640 MPa and then decreases to 454 MPa. However, elongation ratio increases gradually from 16 to 23 and then 31 pct after annealing. The results illustrate that the steel after annealing at 1073 K (800 °C) has better properties, also indicating that combination of dual nano- and micro-crystalline austenite phase is conductive to improving tensile properties of materials.     

Influence of Temperature and Holding Time on the Interaction of V,Al, and N in Microalloyed Forging Steels

A medium-carbon vanadium microalloyed steel (38MnSiVS5) with three different aluminum levels (0.006, 0.020, and 0.03 wt pct) was used to examine the interaction of vanadium, aluminum, and nitrogen during the heating and cooling cycle for forging. The thermal cycle was simulated using a Gleeble^® 1500. Hold times varied from 5 to 45 minutes and temperature varied from 1323 K to 1523 K (1050 °C to 1250 °C). Thermal simulation specimens and as-received material were characterized by quantitative metallography, hardness, and chemical analysis of electrolytically extracted precipitates. The hardness was observed to be relatively constant for all aluminum levels after all thermal simulations at and above 1423 K (1150 °C). Hardness, pearlite fraction, and austenite grain size decreased with increasing aluminum content at the two lowest temperatures examined, which were 1323 K and 1373 K (1050 °C and 1100 °C). The amount of vanadium precipitated in the lowest aluminum steel was very consistent, approximately 70 pct, for the thermal simulations. The amount of precipitated vanadium decreased with increasing amount of aluminum nitride for the 0.03 wt pct Al level.     

Sintering High Tungsten Content W-Ni-Fe Heavy Alloys by Microwave Radiation

This paper presents a detailed study of microwave (MW) sintering of W-Ni-Fe heavy alloys (WHAs) with tungsten (W) content 90 to 98 mass pct (Ni and Fe mass ratio of 7 to 3) in comparison with conventional (CV) hydrogen sintering. Experimental results show that WHAs were MW sintered to fully dense (≥99 pct of theoretical) when heated to sintering temperatures at a heating rate of 50 K/min to 80 K/min (50 °C/min to 80 °C/min) and isothermally held for 2 to 10 minutes, with sintering cycle times of only 25 to 35 minutes (excluding the cooling time). The desired microstructures of finer W grains, more matrix phases, and lower W contiguity (in 95W and 98W) were produced compared to the counterparts by CV sintering. Such microstructural features offered the alloys excellent tensile properties: ultimate tensile strengths (UTS) 1080 to 1110 MPa and tensile elongation 22.1 to 26.8 pct in 90 to 95W, and UTS 920 MPa and elongation 11.2 pct in 98W. MW sintering appeared to be more effective in fabricating WHAs with W content ≥95 pct. It was observed that the superior UTS with MW-sintered alloys was mainly due to the fast heating and shortened isothermal holding times. Prolonged sintering led to substantial grain coarsening as a result of faster tungsten grain growth in MW sintering, and consequently deteriorated the tensile properties. The grain growth rate constant K achieved was calculated to be 5.1 μm³/s for MW sintering compared to 2.9 μm³/s for CV sintering. Fast heating and short isothermal holding times are thus suggested for the fabrication of WHAs by MW sintering.     

On the Stability of Reversely Formed Austenite and Related Mechanism of Transformation in an Fe-Ni-Mn Martensitic Steel Aided by Electron Backscattering Diffraction and Atom Probe Tomography

The stability of reversely formed austenite and related mechanism of transformation were investigated against temperature and time in an Fe-9.6Ni-7.1Mn (at. pct) martensitic steel during intercritical annealing at a dual-phase (α + γ) region. Dilatometry, electron backscattering diffraction (EBSD), atom probe tomography (APT), and X-ray diffraction (XRD) were used to characterize the mechanism of reverse transformation. It was found that under intercritical annealing at 853 K (580 °C), when the heating rate is 20 K/s (20 °C/s), reverse transformation takes place through a mixed diffusion control mechanism, i.e., controlled by bulk diffusion and diffusion along the interface, where Ni controls the diffusion as its diffusivity is lower than that of Mn in the martensite and austenite. Increasing the intercritical annealing to 873 K (600 °C) at an identical heating rate of 20 K/s (20 °C/s) showed that reverse transformation occurs through a sequential combination of both martensitic and diffusional mechanisms. The transition temperature from diffusional to martensitic transformation was obtained close to 858 K (585 °C). Experimental results revealed that the austenite formed by the diffusional mechanism at 853 K (580 °C) mainly remains untransformed after cooling to ambient temperature due to the enrichment with Ni and Mn. It was also found that the stability of the reversely formed austenite by martensitic mechanism at 873 K (600 °C) is related to grain refinement.     

The tensile properties of an Fe-4 pct Mo-0.2 pct C martensite tempered under applied stress

In Fe-4 pct Mo-0.2 pct C martensite which is a typical secondary hardening steel, premature failure o°Curred in tensile test at 600 °C to 700°C where solute atoms could diffuse easily. To clarify this phenomenon, the quenched specimens were tempered under applied stress and tensile-tested at room temperature. The following results were obtained: (1) Typical intergranular fracture was observed in specimens tempered in a temperature range of 600 °C to 650 °C with tempering times of five minutes to 10 minutes and applied stress (70 MPa to 140 MPa). (2) Based on Auger analysis, this phenomenon was considered to be caused by segregation of P, S, and Mo on prior austenite grain boundaries due to applied stress. (3) The direction of applied stress was found to be very significant. Namely, when the tensile direction was parallel to the applied stress during tempering, the specimen was more brittle, and when tensile direction was normal to the applied stress, the specimen was not so brittle. (4) To reduce this embrittlement, solution treatment temperature was adjusted, and it was found that the embrittlement was considerably reduced both in specimens with fine prior austenite grains and with some ferrite phase on prior austenite grain boundaries. TAKATOSHI OGAWA, formerly with Kyoto University. YOSHIFUMI OHMURA, formerly with Kyoto University. This paper is based on a presentation made at the “pcter G. Winchell Symposium on Tempering of Steel” held at the Louisville Meeting of The Metallurgical Society of AIME, October 12-13, 1981, under the sponsorship of the TMS-AIME Ferrous Metallurgy and Heat Treatment Committees.     

Ductility and strain-induced transformation in a high-strength transformation-induced plasticity-aided dual-phase steel

The influence of forming temperature and strain rate on the ductility and strain-induced transformation behavior of retained austenite in a ferritic 0.4C-1.5Si-1.5Mn (wt pct) dual-phase steel containing fine retained austenite islands of about 15 vol pct has been investigated. Ex- cellent combinations of total elongations (TELs), about 48 pct, and tensile strength (TS), about 1000 MPa, were obtained at temperatures between 100 °C and 200 °C and at a strain rate of 2.8 X 10_-4/s. Under these optimum forming conditions, the flow curves were characterized by intensive serrations and increased strain-hardening rate over a large strain range. The retained austenite islands were mechanically the most stable at temperatures between 100 °C and 200 °C, and the retained austenite stability appeared to be mainly controlled by strain-induced martensite and bainite transformations (SIMT and SIBT, respectively), with deformation twinning occur- ring in the retained austenite. The enhanced TEL and forming temperature dependence of TEL were primarily connected with both the strain-induced transformation behavior and retained aus- tenite stability.     

The Tensile Properties of an Fe-4 Pct Mo-0.2 Pct C Martensite Tempered under Applied Stress

In Fe-4 pct Mo-0.2 pct C martensite which is a typical secondary hardening steel, premature failure occurred in tensile test at 600 °C to 700 °C where solute atoms could diffuse easily. To clarify this phenomenon, the quenched specimens were tempered under applied stress and tensile-tested at room temperature. The following results were obtained: (1) Typical intergranular fracture was observed in specimens tempered in a temperature range of 600 °C to 650 °C with tempering times of five minutes to 10 minutes and applied stress (70 MPa to 140 MPa). (2) Based on Auger analysis, this phenomenon was considered to be caused by segregation of P, S, and Mo on prior austenite grain boundaries due to applied stress. (3) The direction of applied stress was found to be very significant. Namely, when the tensile direction was parallel to the applied stress during tempering, the specimen was more brittle, and when tensile direction was normal to the applied stress, the specimen was not so brittle. (4) To reduce this embrittlement, solution treatment temperature was adjusted, and it was found that the embrittlement was considerably reduced both in specimens with fine prior austenite grains and with some ferrite phase on prior austenite grain boundaries. Formerly with Kyoto University Formerly with Kyoto University This paper is based on a presentation made at the “Peter G. Winchell Symposium on Tempering of Steel” held at the Louisville Meeting of The Metallurgical Society of AIME, October 12-13, 1981, under the sponsorship of the TMS-AIME Ferrous Metallurgy and Heat Treatment Committees.     

Effect of Mn Addition on Microstructural Modification and Cracking Behavior of Ferritic Light-Weight Steels

In the present study, effects of Mn addition on cracking phenomenon occurring during cold rolling of ferritic light-weight steels were clarified in relation to microstructural modification involving κ-carbide, austenite, and martensite. Four steels were fabricated by varying Mn contents of 3 to 12 wt pct, and edge areas of steel sheets containing 6 to 9 wt pct Mn were cracked during the cold rolling. The steels were basically composed of ferrite and austenite in a band shape, but a considerable amount of κ-carbide or martensite existed in the steels containing 3 to 6 wt pct Mn. Microstructural observation of the deformed region of fractured tensile specimens revealed that cracks which were initiated at ferrite/martensite interfacial κ-carbides readily propagated along ferrite/martensite interfaces or into martensite areas in the steel containing 6 wt pct Mn, thereby leading to the center or edge cracking during the cold rolling. In the steel containing 9 wt pct Mn, edge cracks were found in the final stage of cold rolling because of the formation of martensite by the strain-induced austenite to martensite transformation, whereas they were hardly formed in the steel containing 12 wt pct Mn. To prevent or minimize the cracking, it was recommended that the formation of martensite during the cooling from the hot rolling temperature or during the cold rolling should be suppressed, which could be achieved by the enhancement of thermal or mechanical stability of austenite with decreasing austenite grain size or increasing contents of austenite stabilizers.     

Intercritically annealed and isothermally transformed 0.15 Pct C steels containing 1.2 Pct Si-1.5 Pct Mn and 4 Pct Ni: Part I. transformation,microstructure, and room-temperature mechanical properties

Steels containing 0.15 pct C and 1.2 pct Si-1.5 pct Mn or 4 pct Ni were intercritically annealed and isothermally transformed between 300 °C and 500 °C for 1 to 60 minutes. The specimens were subjected to tensile testing at room temperature, and the microstructures were evaluated by light microscopy, scanning and transmission electron microscopy (SEM and TEM, respectively), and X-ray diffraction (XRD). The microstructures consist of dispersed regions of bainite, martensite, and austenite in a matrix of ferrite, and a maximum of 11.6 pct austenite is retained after isothermal holding at 450 °C in the Si-Mn steel. In specimens where austenite transforms to martensite during quenching after isothermal holding, the stress-strain curves show continuous yielding, high ultimate tensile strength (UTS), and relatively low ductility. In specimens where higher volume fractions of austenite transform to bainite during isothermal holding, the stress-strain curves show discontinuous yielding, low UTS, and high ductility.     

Development of a High-Strength Ultrafine-Grained Ferritic Steel Nanocomposite

This article describes the microstructural and mechanical properties of 12YWT oxide-dispersion-strengthened (ODS)-ferritic steel nanocomposite. According to the annealing results obtained from X-ray diffraction line profile analysis on mechanically alloyed powders milled for 80 hours, the hot extrusion at 1123 K (850 °C) resulted in a nearly equiaxed ultrafine structure with an ultimate tensile strength of 1470 MPa, yield strength of 1390 MPa, and total elongation of 13 pct at room temperature comparable with high-strength 14YWT ODS steel. Maximum total elongation was found at 973 K (600 °C) where fractography of the tensile specimen showed a fully ductile dimple feature compared with the splitting cracks and very fine dimpled structure observed at room temperature. The presence of very small particles on the wall of dimples at 1073 K (800 °C) with nearly chemical composition of the matrix alloy was attributed to the activation of the boundaries decohesion mechanism as a result of diffusion of solute atoms. The results of Charpy impact test also indicated significant improvement of transition temperature with respect to predecessor 12YWT because of the decreased grain size and more homogeneity of grain size distribution. Hence, this alloy represented a good compromise between the strength and Charpy impact properties.     

Constitutive Modeling of the Mechanical Properties of V-added Medium Manganese TRIP Steel

In this study, medium Mn transformation-induced plasticity steel with the composition Fe-0.08 pct C-6.15 pct Mn-1.5 pct Si-2.0 pct Al-0.08 pct V was investigated. After intercritical annealing at 1013 K (740 °C), the steel contained coarse-grained ferrite and two ultrafine-grained (UFG) phases: ferrite and retained austenite. The material did not deform by localized Lüders band propagation: it did not suffer from this major problem as most UFG steels do. Localization of plastic flow was shown to be suppressed because of a combination of factors, including a bimodal grain size distribution, a multiphase microstructure, the presence of nanosized vanadium carbide precipitates, and the occurrence of the deformation-induced martensitic transformation of retained austenite. A constitutive model incorporating these effects was developed. The model was used to identify the factors which can lead to a further improvement of the mechanical properties of the UFG medium Mn TRIP steels.