液相还原法制备纳米镍粉

采用液相还原法在搅拌反应器内进行了纳米镍粉的制备研究。系统考察了反应物浓度、反应物配比（N₂H₄：NiSO₄）、引发剂浓度、氢氧化钠浓度、反应温度、搅拌速度等操作条件对镍粉物性的影响规律,获得了较优操作条件：NiSO₄为0.8 mol·L^-1,反应物配比为6：1,NaBH₄浓度为0.01 mol·L^-1,NaOH浓度为1 mol·L^-1,反应温度80℃,搅拌速度为2400 r·min^-1,在较优条件下制备出常温下稳定性良好、平均粒径107 nm的面心立方结构的纳米镍粉。     

染料探针分子对水中铜离子的可视化识别及试纸化应用

设计合成了以罗丹明为母体的探针分子RCu,可实现对Cu²⁺的选择性识别。在HEPES缓冲溶液(2×10^-5 mol·L^-1, pH 7.4)的测试体系中RCu本身无颜色,加入Cu²⁺后溶液变为粉红色,而且加入其他常见金属阳离子无颜色变化。探针分子可识别较低浓度的Cu²⁺,检出限可达6.37×10^-8 mol·L^-1。同时探针分子可用于试纸化检测,对水样中的Cu²⁺可实现低浓度的检测,具有一定的实用价值。     

球形离子筛吸附剂的制备及其锂吸附性能评价

利用琼脂糖溶液的溶胶凝胶性质,通过锐孔凝固浴法,对实验室合成的Li₄Mn₅O₁₂粉体进行成型,制备了粒径2～3 mm的球形颗粒,对球形颗粒进行交联后,用1 mol·L^-1的盐酸对球形颗粒进行酸洗脱锂,最终制得球形锂离子筛吸附剂。考察球形吸附剂制备和交联的影响因素,结果表明：5%的琼脂糖浓度和90 ℃的温度为最佳制备条件,2 ml·g^-1的交联剂用量和6 h的交联时间为最佳交联条件。对球形离子筛吸附剂进行静态评价实验,结果表明锂吸附容量为4.25 mmol·g^-1,吸附速率为1.77×10^-5 s^-1,成型后离子筛吸附量是离子筛粉末的75.6%,吸附速率较粉体（3.29×10^-4 s^-1）下降一个数量级。Li⁺平衡吸附容量随平衡pH值的升高而增加,在pH>12时吸附容量高达5.5 mmol·g^-1。共存离子选择性实验表明,交联球形离子筛吸附剂对Li⁺具有高选择性,成型后离子筛可以用于盐湖卤水或者海水提锂。     

锌催化电还原脱氯合成2,3,5,6-四氯吡啶:反应机理和工艺优化

采用循环伏安法和恒电位电解法,探讨了含有ZnCl₂的乙睛水混合溶液中五氯吡啶(PCP)在不锈钢阴极表面电还原脱氯生成2,3,5,6-四氯吡啶(2,3,5,6-TCP)的反应机理;采用恒电流电解法对该电还原脱氯过程的各种工艺条件进行了优化。结果表明:该体系中PCP电还原脱氯生成2,3,5,6-TCP主要遵循以Zn/Zn²⁺为氧化还原媒介的间接电还原机理;优化工艺条件下(阴极液含0.025mol·L^-1HCl+15%(体积分数)水+0.2mol·L^-1苯磺酸钠+0.16mol·L^-1ZnCl₂的乙腈溶液;电流密度为1.25A·dm^-2),0.08mol·L^-1PCP能高选择性地脱氯生成2,3,5,6-TCP,2,3,5,6-TCP的收率和电解电流效率分别可达88.7%和59.1%。     

溴化1-乙烯基-3-烷基咪唑离子液体的电化学性能

合成了溴化1-乙烯基-3-烷基咪唑([VAIM]Br)离子液体,采用FTIR、¹H NMR、TG及DSC进行了表征,并系统研究了[VAIM]Br的电化学性能。结果表明:在298.15～323.15 K内,[VAIM]Br的电导率(σ)与温度符合Arrhenius方程,电导活化能随[VAIM]⁺上烷基链的增长而降低。分别以水、甲醇和乙醇为溶剂的[VAIM]Br溶液的电导率均随浓度的增大而显著增大,且σ(水)>σ(甲醇)>σ(乙醇)。通过电导法确定了[VAIM]Br在水、甲醇、乙醇中的临界胶束浓度,分别约为6.8×10^-6、1.5×10^-5、2.0×10^-5 mol·L^-1,表面活性优异。[VAIM]Br的电化学窗口在1.6～2.5 V,其电化学稳定性随[VAIM]⁺上烷基链的增长而逐渐降低。     

含硫酸亚铁废溶液的生物氧化过程中氮源对溶解性Fe（Ⅲ）生成量的影响

利用嗜酸性氧化亚铁硫杆菌将含硫酸亚铁废溶液中的Fe²⁺氧化成Fe³⁺后用于脱除H₂S,同时实现了含硫酸亚铁废溶液的循环利用和H₂S的脱除。而溶解性Fe³⁺较高的生成量是保证该处理系统连续高效运行的关键因素。但在充足氮源和K⁺条件下大量Fe³⁺以黄铁矾沉淀形式存在。因此,本文通过控制氮源种类及投加浓度,减少沉淀生成,增大溶解性Fe³⁺生成量,以期提高H₂S的去除效率。结果表明（NH₄）₂HPO₄可替代以往研究中的（NH₄）₂SO₄作为氮源,确定适宜菌体生长的氮源浓度范围为0.33～1 g·L^-1。在1 g·L^-1 （NH₄）₂HPO₄条件下细菌生长无明显停滞期、Fe²⁺平均氧化速率为0.221～0.229 g·（L·h） ^-1,Fe³⁺生成量为7.62～7.72 g·L^-1,沉淀量为1.17 g·L^-1,因此确定（NH₄）₂HPO₄为1 g·L^-1时最能保证H₂S的脱除效率。为降低工艺成本,最低可采用0.33 g·L^-1为运行浓度。该优化方案不仅保证了菌体的Fe²⁺氧化活性,而且有效地减少了菌体培养过程中沉淀的产生,获得了较高的Fe³⁺生成量和增速,为使用含硫酸亚铁废溶液处理H₂S的工艺条件优化提供了依据。     

PAN-H1.6Mn1.6O4锂离子筛膜的制备及在卤水中吸附性能

采用亲水的PAN为成膜材料,制备了掺杂H_1.6Mn_1.6O₄的PAN-H_1.6Mn_1.6O₄锂离子筛膜。通过SEM、Li⁺静态吸附实验、（NH₄）₂S₂O₈对锂的洗脱实验和卤水中吸附实验,研究了锂离子筛的添加量对PAN-H_1.6Mn_1.6O₄锂离子筛膜结构、Li⁺吸附-洗脱性能的影响。结果表明,PAN浓度为10%（质量）,H_1.6Mn_1.6O₄的添加量为50%（质量）时,PAN-H_1.6Mn_1.6O₄离子筛膜的吸附量为17.45 mg·g^-1,达到粉末状吸附量的88.0%。以（NH₄）₂S₂O₈为洗脱剂,当浓度为0.3 mol·L^-1、液固比为600:1、时间为12 h时,锂洗脱量为17.23 mg·g^-1,锰溶损率仅为1.14%。在含有Na⁺、K⁺、Mg²⁺和Ca²⁺的罗布泊老卤卤水中,锂离子筛膜对Li⁺有很高的选择性。在卤水中进行10次吸附与解吸循环,吸附量从11.64 mg·g^-1下降到10.94 mg·g^-1,吸附容量仅损失6.0%。总体结果表明亲水性载体对H_1.6Mn_1.6O₄吸附容量影响较小,温和的洗脱剂对锂离子筛膜的化学稳定性有利。     

木质素的化学改性及其对AuCl4-的吸附

以稻草为原料,经预处理、酚化、交联、氯化、胺化、季铵化制备了一种新型的化学改性木质素并对其进行了FTIR,SEM,TG-DSC分析,考察了AuCl₄^-初始浓度、吸附时间、盐酸浓度对化学改性木质素吸附AuCl₄^-效果的影响,探讨了吸附过程的机理。结果表明,制备的化学改性木质素表面致密且在217℃以下具有良好的热稳定性和含有大量酚羟基及胺基。当AuCl₄^-初始浓度为8.0 mmol·L^-1时吸附容量达到最大,为784.50 mg·g^-1,在AuCl₄^-初始浓度为1.0 mmol·L^-1时吸附达到平衡的时间为600 min,当盐酸浓度为0.5 mol·L^-1和AuCl₄^-初始浓度为1.0 mmol·L^-1时吸附率为98%。吸附过程遵循准二级动力学模型,吸附等温模型与Langmuir拟合较好。AuCl₄^-被化学改性木质素中的酚羟基以金单质的形态还原出来。     

聚丙烯酸钠包覆Fe3O4磁性交联聚合物的制备及其对Pb(Ⅱ)和Cd(Ⅱ)的吸附性能

采用溶液分散聚合和Ca²⁺表面交联制备了聚丙烯酸钠包覆Fe₃O₄的磁性交联聚合物（CPAANa@Fe₃O₄）,对其进行了XRD、FT-IR、SEM和TGA等表征。以CPAANa@Fe₃O₄为吸附剂研究了CPAANa@Fe₃O₄对水溶液中Pb²⁺、Cd²⁺的静态吸附,考察了溶液pH、吸附剂投加量、金属离子初始浓度对吸附的影响。结果表明：CPAANa@Fe₃O₄在pH 2～6范围内均具有较好的吸附性能,当吸附剂投加量分别为1.0 g·L^-1和1.6 g·L^-1时对初始浓度分别为200 mg·L^-1的Pb²⁺和100 mg·L^-1的Cd²⁺的去除率达到最大,可使Pb²⁺实现达标排放（GB 8978-1996）;CPAANa@Fe₃O₄对Pb²⁺和Cd²⁺的吸附动力学符合准二级模型,吸附等温线符合Langmuir模型,对Pb²⁺和Cd²⁺的最大吸附量分别为454.55 mg·g^-1和275.48 mg·g^-1。将CPAANa@Fe₃O₄用于处理实际电解矿浆废水,发现能有效吸附其中的Pb²⁺和Cd²⁺,具有潜在实用价值。     

以Ce3+/Ce4+为媒质间接电合成1,4-萘醌

探讨了以Ce³⁺/Ce⁴⁺为媒质的1,4-萘醌间接电化学合成反应。考察了液相氧化、Ce³⁺电解氧化过程的影响因素,并进行了萘醌的间接电合成实验。结果发现,硫酸浓度、溶液温度对铈离子的氧化能力和电化学反应活性具有重要的影响;当温度为70℃、硫酸浓度为1.0 mol·L^-1时,液相氧化反应的收率最高(85.8%)。Ce³⁺电解氧化的最优条件为:电流密度50 mA·cm^-2、硫酸浓度1.0 mol·L^-1、温度为50℃,其电流效率可达90.6%;间接电合成实验过程中萘醌的平均收率达85.7%,Ce³⁺电解氧化的平均电流效率达87.8%,并且电解过程具有良好的稳定性,表明该技术具有良好的产业化应用前景。     

微波辅助二次生长法合成SAPO-34分子筛膜与关键影响因素

采用微波辅助二次生长法在α-Al₂O₃载体上合成了SAPO-34分子筛膜，并将其应用于CO₂/CH₄分离。通过扫描电镜、X射线衍射和傅里叶变换红外光谱等表征方法，系统考察了加热方式、晶种粒径、老化时间和晶化时间对SAPO-34分子筛膜表面形貌和结构的影响。实验结果表明，以0.4 μm分子筛作为晶种，在老化24 h，然后微波加热晶化4 h后可制备出厚度约为1.5 μm的致密、无缺陷SAPO-34分子筛膜，其平均CO₂/CH₄分离因子和CO₂渗透率分别达到81和6.6×10^-7 mol·m^-2·s^-1·Pa^-1，制备方法可靠，重复性高。     

基于高盐条件下的Bacillus circulans WZ-12 CCTCC M 207006好氧降解氯化碳氢化合物(英文)

A novel saline-tolerant bacterium Bacillus circulans WZ-12 was evaluated for its potential to degrade four chlorinated hydrocarbons under saline conditions.CH2Cl2 was effectively degraded by Bacillus circulans WZ-12 cells in the medium containing NaCl concentrations ranging from 5 g·L-1 to 10 g·L-1,and the maximum degradation efficiency(85%) was achieved at NaCl concentration of 10 g·L-1.Similarly,Bacillus circulans WZ-12 was able to degrade CH2 BrCl,C2H4Cl2,and C2H2Cl2 in the presence of 10 g NaCl per liter within 24 h.Cells of Bacillus circulans WZ-12 grown in minimal salt medium contained low levels of glycine betaine(GB),but GB levels were 3-to 5-fold higher in cells grown in media with high salt.Kinetic analysis revealed that biodegradation of the four chlorinated hydrocarbons was concentration dependent and a linear inverse correlation(R 2-0.85-0.94) was observed between the rate of biodegradation(V) and salt concentration from 5 g·L-1 to 60 g·L-1.The growing cells(in minimal salt medium) degraded approximately 50% of the CH2Cl2 within 24 h,whereas the resting cells(in physiological saline) degraded only 25% of the CH2Cl2 within 24 h and were inactive after 36 h cultivation.Biodegradation could be repeatedly performed for more than 192 h with more than 50% removal efficiency.Bacillus circulans WZ-12 grows well in an aqueous/oil system,hence,it is effective for the treatment of industrial effluents that contain chlorinated hydrocarbons with high salt concentrations.     

Aerobic Biodegradation of Chlorinated Hydrocarbons by Bacillus circulans WZ-12 CCTCC M 207006 under Saline Conditions

A novel saline-tolerant bacterium Bacillus circulans WZ-12 was evaluated for its potential to degrade four chlorinated hydrocarbons under saline conditions. CH₂Cl₂ was effectively degraded by Bacillus circulans WZ-12 cells in the medium containing NaCl concentrations ranging from 5 g·L^-1 to 10 g·L^-1, and the maximum degradation efficiency (85%) was achieved at NaCl concentration of 10 g·L^-1. Similarly, Bacillus circulans WZ-12 was able to degrade CH₂BrCl, C₂H₄Cl₂, and C₂H₂Cl₂ in the presence of 10 g NaCl per liter within 24 h. Cells of Bacillus circulans WZ-12 grown in minimal salt medium contained low levels of glycine betaine (GB), but GB levels were 3- to 5-fold higher in cells grown in media with high salt. Kinetic analysis revealed that biodegradation of the four chlorinated hydrocarbons was concentration dependent and a linear inverse correlation (R² 0.85-0.94) was observed between the rate of biodegradation (V) and salt concentration from 5 g·L^-1 to 60 g·L^-1. The growing cells (in minimal salt medium) degraded approximately 50% of the CH₂Cl₂ within 24 h, whereas the resting cells (in physiological saline) degraded only 25% of the CH₂Cl₂ within 24 h and were inactive after 36 h cultivation. Biodegradation could be repeatedly performed for more than 192 h with more than 50% removal efficiency. Bacillus circulans WZ-12 grows well in an aqueous/oil system, hence, it is effective for the treatment of industrial effluents that contain chlorinated hydrocarbons with high salt concentrations.     

界面聚合法制备用于脱氮提纯CH4的N2优先渗透ZIF-90/聚酰胺混合基质膜

作为一种高效的分离方法,膜法分离非常规天然气具有较理想的应用前景。相较CH₄优先渗透膜,N₂优先渗透膜优势在于分离N₂/CH₄混合气后CH₄处于高压侧,利于后续处理。以均苯三甲酰氯为油相单体,间苯二胺为水相单体,采用界面聚合法在聚砜基膜上制备致密超薄聚酰胺分离层,并通过向其中引入孔径可允许N₂分子通过而不允许CH₄分子通过的纳米颗粒ZIF-90,在膜内形成固定的N₂传递通道,成功制备了用于脱氮提纯CH₄的N₂优先渗透混合基质膜。膜渗透选择性能测试结果显示当混合基质膜中纳米颗粒掺杂量为0.30 g·L^-1时,2 bar（1 bar=0.1 MPa）进料压力下,N₂渗透速率达1.16×10^-9 mol·m^-2·s^-1·Pa^-1,N₂/CH₄分离因子达16.6,分离因子比未掺杂ZIF-90的聚酰胺膜提高46.5%,具有一定的处理非常规天然气脱氮提纯甲烷的应用潜力。     

界面聚合法制备用于脱氮提纯CH4的N2优先渗透ZIF-90/聚酰胺混合基质膜

作为一种高效的分离方法,膜法分离非常规天然气具有较理想的应用前景。相较CH₄优先渗透膜,N₂优先渗透膜优势在于分离N₂/CH₄混合气后CH₄处于高压侧,利于后续处理。以均苯三甲酰氯为油相单体,间苯二胺为水相单体,采用界面聚合法在聚砜基膜上制备致密超薄聚酰胺分离层,并通过向其中引入孔径可允许N₂分子通过而不允许CH₄分子通过的纳米颗粒ZIF-90,在膜内形成固定的N₂传递通道,成功制备了用于脱氮提纯CH₄的N₂优先渗透混合基质膜。膜渗透选择性能测试结果显示当混合基质膜中纳米颗粒掺杂量为0.30 g·L^-1时,2 bar（1 bar=0.1 MPa）进料压力下,N₂渗透速率达1.16×10^-9 mol·m^-2·s^-1·Pa^-1,N₂/CH₄分离因子达16.6,分离因子比未掺杂ZIF-90的聚酰胺膜提高46.5%,具有一定的处理非常规天然气脱氮提纯甲烷的应用潜力。     

Gas separation using sol-gel derived microporous zirconia membranes with high hydrothermal stability☆

A microporous zirconia membrane with hydrogen permeance about 5 × 10?8 mol·m?2·s?1·Pa?1, H2/CO2 permselectivity of ca. 14, and excellent hydrothermal stability under steam pressure of 100 kPa was fabricated via polymeric sol–gel process. The effect of calcination temperature on single gas permeance of sol–gel derived zirconia membranes was investigated. Zirconia membranes calcined at 350 °C and 400 °C showed similar single gas permeance, with permselectivities of hydrogen towards other gases, such as oxygen, nitrogen, methane, and sulfur hexafluoride, around Knudsen values. A much lower CO2 permeance (3.7 × 10?9 mol·m?2·s?1·Pa?1) was observed due to the interaction between CO2 molecules and pore wall of membrane. Higher calcination tem-perature, 500 °C, led to the formation of mesoporous structure and, hence, the membrane lost its molecular siev-ing property towards hydrogen and carbon dioxide. The stability of zirconia membrane in the presence of hot steam was also investigated. Exposed to 100 kPa steam for 400 h, the membrane performance kept unchanged in comparison with freshly prepared one, with hydrogen and carbon dioxide permeances of 4.7 × 10?8 and~3 × 10?9 mol·m?2·s?1·Pa?1, respectively. Both H2 and CO2 permeances of the zirconia membrane de-creased with exposure time to 100 kPa steam. With a total exposure time of 1250 h, the membrane presented hydrogen permeance of 2.4 × 10?8 mol·m?2·s?1·Pa?1 and H2/CO2 permselectivity of 28, indicating that the membrane retains its microporous structure.     

Hydrophobic modification of SAPO-34 membranes for improvement of stability under wet condition

SAPO-34 zeolite membranes show high efficiency for CO₂/CH₄ separation but suffer from the reduction of separation performance when exposed to humid atmosphere. In this work, n-dodecyltrimethoxysilane (DTMS) was used to modify the hollow fibers supported SAPO-34 membranes to increase the external surface hydrophobicity and thus sustain their performance under moisture environment. The modified membranes were fully characterized. Their separation performance was extensively investigated in both dry and wet gaseous systems and compared with the un-modified ones. The un-modified SAPO-34 membrane exhibited a high separation selectivity of 160 and CO₂ permeance of 1.18×10^-6 mol·m^-2·s^-1·Pa^-1 for separation of dry CO₂/CH₄ at 298 K. However, its separation selectivity declined to 0.9 and the CO₂ permeance was only about 1.7×10^-8 mol·m^-2·s^-1·Pa^-1 for wet CO₂/CH₄ at same temperature. High temperature (e.g. 353 K) could reduce the effect of moisture to improve SAPO-34 separation selectivity, but further increasing temperature (e.g. 373 K) led to decrease in CO₂/CH₄ separation selectivity. A significant decrease of selectivity was observed at higher pressure drop. The modified SAPO-34 membrane showed decreased CO₂ permeance but increased separation selectivity for dry CO₂/CH₄ gas mixture, and super performance for wet CO₂/CH₄ gas mixture due to the improved hydrophobicity of membrane surface. A separation selectivity of 65 and CO₂ permeance of 4.73×10^-8 mol·m^-2·s^-1·Pa^-1 for wet CO₂/CH₄ mixture can be observed at 353 K with a pressure drop of 0.4 MPa. Furthermore, the modified membrane exhibited stable separation performance during the 120-hour test for wet CO₂/CH₄ mixture at 353 K. The hydrophobic modification paves a way for SAPO-34 membranes in real applications.     

Synthesis and permeation properties of ion-exchanged ETS-4 tubular membranes

Zeolite membranes, which were composed of ETS-4 with Na cations, were prepared on porous -alumina tubes by hydrothermal synthesis. The membranes, which were formed under optimized conditions, sharply rejected molecules with sizes larger than 0.4 nm. For mixtures of N₂–CO₂, N₂–O₂, N₂–Ar and N₂–CH₄ systems, N₂ permeated faster than the coexisting gas. The N₂/O₂ separation factor for an equimolar mixture was in the range of 2.3–3.5, and the N₂ permeance was in the range of (0.55–2.8)×10⁻⁸ mol m⁻² s⁻¹ Pa⁻¹ at permeation temperatures of 283–333 K. Moisture had some effect on the permeation properties for N₂–O₂ mixtures. The separation factor for the N₂/CH₄ system was larger than that of the N₂/O₂ system. When the membrane was ion exchanged with either Li⁺ or Sr²⁺, the separation factors for N₂/O₂ and N₂/CH₄ systems increased, while the permeances decreased.