多层次微观复合陶瓷的力学性能和优化分析研究

研究了不同层次微观复合陶瓷的力学性能随纳米和微米颗粒含量变化的影响。结果表明材料强度与韧性的改善与两种弥散相含量及其相对比例有关。优化分析可表征临界裂纹长度的变化规律, 当纳米SiC_n 含量为3～ 12vo l% , 材料内部的裂纹长度较小且随微米SiC_P 含量增加而略有增大。达到最大韧性时弥散相的优化体积分数(9. 7vo l% , 9. 7vo l% ) 要高于达到最大强度时的弥散相含量(7. 9vo l% , 7. 9vo l% ) , 表明韧性与强度最大值的组成点不一致, 其原因在于瓷体内部缺陷对其敏感程度不同。      

Fracture toughness of microsphere Al2O3–Al particulate metal matrix composites

The fracture toughness and behaviour of COMRAL-85^TM, a 6061 aluminium–magnesium–silicon alloy reinforced with 20 vol% Al₂O₃-based polycrystalline ceramic microspheres, and manufactured by a liquid metallurgy route, have been investigated. Fracture toughness tests were performed using short rod and short bar (chevron-notch) specimens machined from extruded 19 mm diameter rod, heat treated to the T6 condition. The fracture toughness in the R–L orientation was found to be lower than in the C–R or L–R orientations owing to the presence of particle-free bands in the extrusion direction. Short rod tests were also conducted for the R–L orientation on six powder metallurgy composites with particle volume fractions ranging between 5% and 30%. It was found that the fracture toughness decreased progressively with particle volume fraction, but at a decreasing rate. A detailed examination of the fracture behaviour was made for both the liquid metallurgy and powder metallurgy processed composites.     

Crack growth resistance (R-curve) behaviour and thermo-physical properties of Al2O3 particle-reinforced AlN/Al matrix composites

Crack growth resistance behaviour and thermo-physical properties of Al₂O₃ particle-reinforced AlN/Al matrix composites have been studied as a function of AlN volume fraction as well as Al₂O₃ particle size. The fracture toughness of the composites decreased with increase in vol% AlN and decrease in Al₂O₃ particle size. All the composites exhibited R-curve behaviour which has been attributed to crack bridging by the intact metal ligaments behind the crack tip. The Young’s modulus of the composites increased with the vol% of AlN whereas the thermal diffusivity and coefficient of thermal expansion followed a reverse trend. The composites exhibited hysteresis in thermal expansion as a function of temperature and the hysteresis decreased with decrease in metal content of the composite.     

Studies of the effect of metal particles on the fracture toughness of ceramic matrix composites

The purpose of this study was to describe the influence of metal particles on the fracture toughness of ceramic matrix composites. Here, alumina matrix composites with molybdenum particles have been investigated. The results presented show that the change of fracture toughness of a ceramic–metal composite can be controlled by the volume fraction of metallic phase and size of metal particles.

The model proposed in this paper describes the change of crack length and as a consequence, the change of K_IC value. The results of modelling calculations have been compared with experimentally measured K_IC values. This model is useful for simulation of crack length changes in the composites and to design a material with an optimum fracture toughness.     

Toughening of a brittle thermosetting polymer: Effects of reinforcement particle size and volume fraction

Micron- and nanometer-sized aluminum particles were used as reinforcements to enhance the fracture toughness of a highly-crosslinked, nominally brittle, thermosetting unsaturated polyester resin. Both particle size and particle volume fraction were systematically varied to investigate their effects on the fracture behavior and the fracture toughness. It was observed that, in general, the overall fracture toughness increased monotonically with the volume fraction of aluminum particles, for a given particle size, provided particle dispersion and deagglomeration was maintained. The fracture toughness of the composite was also strongly influenced by the size of the reinforcement particles. Smaller particles led to a greater increase in fracture toughness for a given particle volume fraction. Scanning electron microscopy of the fracture surfaces was employed to establish crack front trapping as the primary extrinsic toughening mechanism. Finally, the effects of particle volume fraction and size on the tensile properties of the polyester-aluminum composite were also investigated. The measured elastic modulus was in accordance with the rule-of-mixtures. Meanwhile, the tensile strength was slightly reduced upon the inclusion of aluminum particles in the polyester matrix.     

Improving the fracture toughness of MgO–Al2O3–SiO2 glass/molybdenum composites by the microdispersion of flaky molybdenum particles

The flake-forming behaviour of powders of molybdenum, niobium, nickel, BS 316 S 12, Ni–17Cr–6Al–0.6Y, iron, titanium and Ti–6Al–4V, using a wet ball mill, was investigated. MgO–Al₂O₃–SiO₂ (MAS) glass composites reinforced with these flaked particles were fabricated, and improvements in flexural strength evaluated. The MAS glass composites reinforced with flaky metallic particles such as molybdenum, niobium, iron, nickel and Ni–17Cr–6Al–0.6Y, showed an improvement. The effect of molybdenum particle size on the flake-forming behaviour of molybdenum, flexural strength and fracture toughness of MAS glass/molybdenum composites, were investigated. The flake-forming behaviour shows a high degree of dependence on molybdenum particle size and, upto a size of 32 μm, becomes conspicuous with increasing particle size. At 32 μm, the aspect ratio reaches a value of 17 and, above 32 μm, flake forming saturates. Fracture toughness is closely related to flake-forming behaviour and the more marked the flake forming, the greater is the increase in fracture toughness. A composite of MAS glass with flaky molybdenum particles has a greater improvement effect on fracture toughness than composites with SiC whiskers, SiC platelets or ZrO₂ particles. This is closely linked to plastic deformation of the flaky metallic particles at the crack tip at the time of fracture. This revised version was published online in November 2006 with corrections to the Cover Date.     

Optimizing the design of particulate composites for maximum fracture resistance through modeling

The failure modes of particulate reinforced metallic alloys are reviewed with special emphasis on in situ intermetallic particle reinforced niobium alloys, but information derived from ceramic reinforced aluminum alloys is also included. Constraint of plastic deformation by particles is emphasized as one of two very important factors in controlling fracture behavior. The other factor is particle fracture toughness. Models are proposed for describing the fracture toughness, from which several methods of enhancing toughness are envisioned. This modeling of fracture toughness is intended to help optimize the design and processing of these materials for enhanced fracture resistance. This revised version was published online in July 2006 with corrections to the Cover Date.     

Effect of processing parameters and clay volume fraction on the mechanical properties of epoxy-clay nanocomposites

The influence of processing parameters and particle volume fraction was experimentally studied for epoxy clay nanocomposites. Nanocomposites were prepared using onium ion surface modified montmorillonite (MMT) layered clay and epoxy resin (DEGBF). Two different techniques were used for dispersing the clay particles in the epoxy matrix, viz. high-speed shear dispersion and ultrasonic disruption. The volume fraction of clay particles was systematically varied from 0.5 to 6%, and mechanical properties, viz. flexural modulus and fracture toughness, were studied as a function of clay volume fraction and the processing technique. The flexural modulus was observed to increase monotonously with increase in volume fraction of clay particles, while, the fracture toughness showed an initial increase on addition of clay particles, but a subsequent decrease at higher clay volume fractions. In general, nanocomposites processed by shear mixing exhibited better mechanical properties as compared to those processed by ultrasonication. Investigation by X-ray diffraction (XRD) revealed exfoliated clay structure in most of the nanocomposites that were fabricated. Morphologies of the fracture surfaces of nanocomposites were studied using a scanning electron microscopy (SEM). Presence of river markings at low clay volume fractions provided evidence of extrinsic toughening taking place in an otherwise brittle epoxy.     

Effect of filler surface morphology on the impact behaviour of hydroxyapatite reinforced high density polyethylene composites

Instrumented falling weight impact tests have been carried out to characterize the impact behaviour of hydroxyapatite reinforced high-density polyethylene composite (HA-HDPE) in order to use this biomaterial in skull implants. The effects of HA filler surface morphology and volume fraction on the fracture toughness were studied, and fracture mechanism investigated. Impact resistance was found to be markedly improved by using a sintered grade HA filler with smooth particle surface instead of spray dried grade HA with rough surface. SEM examination of impacted fracture surfaces revealed that the improvement of impact resistance was due to the stronger interfacial bonding between smooth HA particles and HDPE polymer matrix compared with that between rough HA and HDPE, which results in more energy absorption during impact and hence better fracture resistance.     

The influence of vanadium on fracture toughness and abrasion resistance in high chromium white cast irons

The influence of vanadium on wear resistance under low-stress conditions and on the dynamic fracture toughness of high chromium white cast iron was examined in both the ascast condition and after heat treatment at 500 °C. A vanadium content varying from 0.12 to 4.73% was added to a basic Fe-C-Cr alloy containing 2.9 or 19% Cr. By increasing the content of vanadium in the alloy, the structure became finer, i.e. the spacing between austenite dendrite arms and the size of massive M₇C₃ carbides was reduced. The distance between carbide particles was also reduced, while the volume fraction of eutectic M₇C₃ and V₆C₅ carbides increased. The morphology of eutectic colonies also changed. In addition, the amount of very fine M₂₃C₆ carbide particles precipitated in austenite and the degree of martensitic transformation depended on the content of vanadium in the alloy. Because this strong carbide-forming element changed the microstructure characteristics of high chromium white iron, it was expected to influence wear resistance and fracture toughness. By adding 1.19% vanadium, toughness was expected to improve by approximately 20% and wear resistance by 10%. The higher fracture toughness was attributed to strain-induced strengthening during fracture, and thereby an additional increment of energy, since very fine secondary carbide particles were present in a mainly austenitic matrix. An Fe-C-Cr-V alloy containing 3.28% V showed the highest abrasion resistance, 27% higher than a basic Fe-C-Cr alloy. A higher carbide phase volume fraction, a finer and more uniform structure, a smaller distance between M₇C₃ carbide particles and a change in the morphology of eutectic colonies were primarily responsible for improving wear resistance.     

Mixture law including particle-size effect on fracture toughness of nano- and micro-spherical particle-filled composites

The effects of particle diameter and volume fraction on fracture toughness of nano- and micro-spherical particle-filled composites were investigated. The purpose was to create a mixture law of fracture toughness based on experimental results of spherical silica particle–filled epoxy composites and a theoretical approach. The fracture toughness of composites was found to be tailored independently by exchanging different particle sizes, and elastic and viscoelastic properties were found to be governed by the volume fraction of the particles. In a theoretical analysis, a mixture law of fracture toughness, composed of the elastic moduli, diameter, and volume fraction of particles and the elastic moduli of matrix resins was proposed. Its validity was demonstrated in a comparison with the experimental results.     

Fracture of alumina particulate reinforced aluminium alloy matrix composites

Fracture toughness tests were performed on two aluminium alloy matrices, 2014-0 and 2024-0 reinforced with alumina particulates of different volume fractions and particulate sizes so as to investigate the fracture mechanisms operative in such composites and to determine how microstructural parameters such as volume fraction, particulate size and interparticle spacing affect the fracture toughness. The results indicate that fracture occurred by a locally ductile mechanism. The fracture toughness increased with increasing particle spacing provided that the particle size was less than a limiting value, above which unstable crack growth occurred and the toughness lowered.     

INFLUENCE OF MICROSTRUCTURE ON WEAR RESISTANCE PARAMETER OF CERAMIC CUTTING TOOLS

This report examines the role of microstructure of a new type of cutting tool material on an existing relationship between its abrasion wear resistance, fracture toughness (K_IC), and hardness (H). Three alumina-silver composites with different amounts of metal particles have been prepared, and their hardness and fracture toughness properties have been determined together with the assessment of their microstructural features such as volume fraction of the second phase, porosity, etc. The mechanical wear on the flanks of cutting tool inserts, made from the developed composites, has also been estimated by machining experiments against 0.45% carbon steel. The results indicate that flank wear resistance of these silver toughened ceramic cutting tool inserts is not proportional to an existing wear resistance parameter K_IC^3/4H^1/2. A modified relation between flank wear resistance, hardness, and fracture toughness has been suggested here for these cutting tool materials. The modification incorporates consideration of the volume fraction of the second phase and the porosity in the developed metal toughened ceramics.     

Effect of mixed mode I/II on fracture behaviour of laminated metal matrix composites

Abstract

The effects of mixed mode loading (I/II) on the fracture toughness and fracture behaviour of both 6090/SiC/20_p-6013 diffusion bonded laminates and 2080/SiC/20_p-2080 adhesive bonded laminates tested in the crack arrester orientation were investigated. The effects of layer thickness and volume fraction ratio on the fracture behaviour under the mixed mode were also studied. The fracture behaviour under mode I/II of available similar discontinuously reinforced aluminium (DRA) materials was additionally compared to that of the laminates. The fracture behaviour of laminates under mode I/II was dependent on the volume fraction ratio and generally different from that of the monolithic and DRA. The increase in the fracture toughness of DRA by lamination with ductile layers under mode I changes somewhat under increasing load mixity, for 75/25 and 50/50 diffusion bonded laminate and 60/40 adhesive bonded laminate ABL. This results from extensive interfacial separation and delamination between the layers.     

SiC颗粒强韧化MoSi2复合材料

通过湿法混料和热压烧结工艺成功地制备了20vo1%SiC_P/MoSi₂复合材料,并测定了其显微组织和力学性能。结果表明:SiC_P/MoSi₂复合材料主要由MoSi₂和SiC颗粒组成,还有少量的Mo₅Si₃,致密度为92.3% 。与MoSi₂相比,其室温抗弯强度提高了30.6%,断裂韧性提高了53%,1200℃的抗压强度提高了44%,1400℃的抗压强度提高了53%;其硬度、弹性模量等性能有较大提高。在Al₂O₃和SiC对磨盘上表现出极其优异的耐磨性能。SiC颗粒对MoSi₂的室温增韧、高温增强效果显著。     

Fracture mechanism of toughened epoxy resin with bimodal rubber-particle size distribution

A bimodal rubber-particle distributed epoxy resin was made by simultaneous addition of two kinds of liquid rubbers, CTBN1300X9 and CTBN1300X13. These rubbers were added at a constant total rubber content but with varying weight ratios. The microstructure and fracture behaviour of these rubber-modified epoxy resins have been studied. A strong increase in the fracture resistance was found for the bimodal rubber-particle distributed epoxy resin. The role of the small particle is thought to toughen the shear bands between large particles. The role of large particle is thought to induce a large-scale shear deformation in the crack front. The synergistic effect of these particles gives rise to a strong increase in the toughness of these bimodal rubber-particle distributed epoxy systems.     

Multi-length scale micromorphic process zone model

The prediction of fracture toughness for hierarchical materials remains a challenging research issue because it involves different physical phenomena at multiple length scales. In this work, we propose a multiscale process zone model based on linear elastic fracture mechanics and a multiscale micromorphic theory. By computing the stress intensity factor in a K-dominant region while maintaining the mechanism of failure in the process zone, this model allows the evaluation of the fracture toughness of hierarchical materials as a function of their microstructural properties. After introducing a multi-length scale finite element formulation, an application is presented for high strength alloys, whose microstructure typically contains two populations of particles at different length scales. For this material, the design parameters comprise of the strength of the matrix–particle interface, the particle volume fraction and the strain-hardening of the matrix. Using the proposed framework, trends in the fracture toughness are computed as a function of design parameters, showing potential applications in computational materials design.     

Influence of heat treatment and particle shape on mechanical properties of infiltrated Al2O3 particle reinforced Al-2 wt-%Cu

Abstract

Al-2 wt-%Cu composites were produced by gas pressure infiltration of powder beds with a high volume fraction (45 to 60 vol.-%) of angular or polygonal alumina particles. The tensile behaviour and fracture toughness of the composites were characterised in as cast, solutionised and peak aged (T6) conditions. It was shown that coarse intermetallics that are formed during solidification and located preferentially at the particle/matrix interface lead to lower toughness compared with the same composites in solutionised and T6 conditions. The particle nature and shape exert a strong influence on the properties of the composites: polygonal particles are intrinsically stronger than angular particles and yield stronger, tougher, and more ductile composites. Composite toughness variations are explained in terms of fracture micromechanisms.     

Preparation, microstructure and mechanical properties of metal-particulate/glass-matrix composites

Composites with a borosilicate glass matrix containing different concentrations of vanadium particles were fabricated by powder metallurgy and hot-pressing. The mechanical properties and fracture behaviour of the composites were assessed by a range of techniques. Young's modulus, fracture strength in bending, and fracture toughness increased with vanadium content. By virtue of the good interfacial bonding and low residual internal stresses, an effective crack-particle interaction during fracture was achieved. The fracture toughness of composites containing 30 vol. % of vanadium inclusions was approximately 65 % higher than that of the unreinforced glass. Experimental values for the fracture toughness increment were in good qualitative agreement with the predictions of theoretical models in the literature. Extensive plastic deformation of the vanadium inclusions was not found, however. This was attributed mainly to the constraint imposed by the rigid matrix surrounding the particles and to possible embrittlement of the particles during composite fabrication at high temperatures. The brittleness index (B) of the composites was calculated and its relevance for characterisation of the ductile versus brittle behaviour of brittle-matrix composites is discussed.     

Mechanical behaviour of nickel aluminide–zirconia transformation-toughened particulate composite

The fracture toughness and strength behaviour of nickel aluminide toughened by partially stabilized as well as by non-stabilized zirconia dispersoids were investigated in the range of zirconia content up to 40 vol%. The temperature dependence of the mechanical properties of the composite with an optimal zirconia content was examined. A considerable increase both in fracture toughness and in bending strength was achieved compared to the base nickel aluminide. To reveal the nature of the toughening and strengthening effects, X-ray diffraction measurements were performed before and after fracture. Residual stresses imposed on zirconia particles were evaluated. Trends in mechanical behaviour have been discussed in terms of microstructure development. This revised version was published online in November 2006 with corrections to the Cover Date.