The athermal α → ω transformation in Zr-2 at% Nb alloy

The athermal transformation in Zr-2 at.% Nb alloy has been investigated by transmission electron microscopy. Analysis of the selected-area diffraction pattern has shown that the orientation relationships between the omega and the parent-phase in quenched Zr-2 at.% Nb alloy are the same as have been previously observed for the reaction in pure zirconium. Thus it was deduced that the direct transition has taken place in the alloy during cooling. The-originated -particles were visualized using the dark-field technique. The formation of the athermal omega in the-region of-stabilized Zr-Nb alloy is discussed in terms of the relative positions of the free energy equilibrium curvesT ₀ ,T ₀ ,T ₀ and the correspondingM _s ,M _s andT _s start curves. It is concluded that the omega phase can occur over a much wider range of alloy compositions than is usually recognized on the basis of transformation data.     

Microstructure and mechanical properties of rapidly quenched L20 and L20+L12 alloys in Ni-Al-Fe and Ni-Al-Co systems

Ductile L2₀-type wires and+L1₂-type duplex wires with high strengths and large elongation in the Ni-Al-Fe and Ni-Al-Co ternary systems have been manufactured directly from the liquid state by an in-rotating-water spinning method. The wire diameter was in the range 80 to 180m and the average grain size was 2 to 4m for the wires and 0.2 to 1.0m for the+ wires. _y, _f and _p of the wires were found to be about 360 to 760 MPa, 560 to 960 MPa, and 0.2 to 5.5%, respectively, for the Ni-Al-Fe system, those of the+ wires were about 395 to 660 MPa, 670 to 1285 MPa, and 3.5 to 17%, respectively, for the Ni-Al-Fe system, and about 260 to 365 MPa, 600 to 870 MPa, and 4.0 to 7.0%, respectively, for the Ni-Al-Co system. Cold-drawing caused a significant increase in _y and _f and the values attained were about 1850 and 2500 MPa, respectively, for Ni-20Al-30Fe and Ni-25Al-30Co wires drawn to about 90% reduction in area. The high strengths, large elongation and good cold-workability of the melt-quenched and+ compound wires have been inferred to be due to the structural change into a low-degree ordered state containing a high density of phase boundaries, suppression of grain-boundary segregation and refinement of grain size.     

The variation of the index of refraction in a vortex tube

Three models of a vortex tube (isentropic, isothermal, and isochoric) are considered as optical inhomogeneities. Expressions relating the index of refraction to the coordinate are obtained. The possibility of obtaining Schlieren pictures of such flows is discussed.Notation a speed of sound - n index of refraction - p pressure - r radius - T absolute temperature - v linear velocity - angular deflection of the beam - x adiabatic exponent - density - angular velocity - ¯v, ¯p etc. dimensionless parameters - v₀, ₀ values at the core bounboundary - p, etc. stagnation values - n_c index of refraction at center of vortex     

Knudsen molecular flow in a channel with a small temperature difference at its ends

The thermomolecular pressure difference (TPD) of helium, argon, and krypton is measured in a packet of glass capillaries for temperatures 273 and 293 K at their ends in a 10–100 range of Knudsen numbers.Notation exponent of the thermomolecular pressure difference effect - Kn Knudsen number - rarefaction parameter - Q_T reduced thermal creep flux - Q_P reduced Poiseuille flux - C(_t) Cercignani-Lampis scattering kernel - R specular scattering kernel - (1 – ) fraction of specular reflection - _t accommodation coefficient of the tangential momentum - P_c, P_h gas pressure in the cold and hot volumes, respectively - coefficient of dynamic viscosity - m mass of gas molecules - k Boltzmann constant - D, L the capillary diameter and length, respectively Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 54, No. 5, pp. 719–724, May, 1988.     

Flow visualization glass-ceramic: Preliminary experimental and modelling results

A glass-ceramic material was developed to act as a flow visualization material. Preliminary experiments indicate that aperiodic, thermally induced, convective flows can be sustained at normal processing conditions. These flows and the stress and temperature gradients induced are most likely responsible for the anomalous behaviour seen in these materials and the difficulties encountered in their development and in their production on industrial and experimental scales. A simple model describing the dynamics of variable-viscosity fluids was developed and was shown to be in qualitative agreement with more sophisticated models as well as with experimental results. The model was shown to simulate the dependence of the critical Rayleigh number for the onset of convection on the viscous properties of the fluid at low T, and also to simulate quenching behaviour when the temperature differences were high.Nomenclature C _p Heat capacity - D, E, F Expansion coefficients - H Height of the roll cell - Pr Prandtl number - R _a Rayleigh number - R _c Critical Rayleigh number for the onset of convection in a constant-viscosity fluid - S Dimensionless stream function - T Temperature - T _m Mean temperature - T ₀ Bottom surface temperature - T _r Reference temperature - a Aspect ratio of cell - g Acceleration due to gravity - k Thermal conductivity - k ₁ Function related to ²v/T ² - k ₂ Function related to ⁴v/T ⁴ - r Rayleigh number ratioR _a/R _c - t Time - w Dimensionless vertical coordinate - w _m Mean cell height - x Horizontal coordinate - y Dimensionless horizontal coordinate - z Vertical coordinate - , Constants - _t Thermal expansion coefficient - Constant in viscosity function - T Temperature difference between top and bottom surfaces - _i Viscosity coefficients - Kinematic viscosity - _m Mean kinematic viscosity - Dimensionless kinematic viscosity - Thermal diffusivity - Non-linear temperature function - Dimensionless non-linear temperature function - _o - Stream function - Dimensionless time - Eigenvalues     

Bounds for traces in complete intersections and degrees in the Nullstellensatz

In this paper we obtain an effective Nullstellensatz using quantitative considerations of the classical duality theory in complete intersections. Letk be an infinite perfect field and let f₁,...,f n–rk[X₁,...,X_n] be a regular sequence with d:=max_j deg f_j. Denote byA the polynomial ringk [X₁,..., X_r] and byB the factor ring k[X₁,...,X_n]/(f₁,...,f_n r); assume that the canonical morphism AB is injective and integral and that the Jacobian determinant with respect to the variables X_r+1,...,X_n is not a zero divisor inB. Let finally B^*:=Hom_A(B, A) be the generator of B^* associated to the regular sequence.We show that for each polynomialf the inequality deg (¯f) dⁿ r(+1) holds (¯fdenotes the class off inB and is an upper bound for (n–r)d and degf). For the usual trace associated to the (free) extensionA B we obtain a somewhat more precise bound: deg Tr(¯f) dⁿ r degf. From these bounds and Bertini's theorem we deduce an elementary proof of the following effective Nullstellensatz: let f₁,..., f_s be polynomials in k[X₁,...,X_n] with degrees bounded by a constant d2; then 1 (f₁,..., f_s) if and only if there exist polynomials p₁,..., p_sk[X₁,..., X_n] with degrees bounded by 4n(d+ 1)ⁿ such that 1=_ip_if_i. in the particular cases when the characteristic of the base fieldk is zero ord=2 the sharper bound 4ndⁿ is obtained.Partially supported by UBACYT and CONICET (Argentina)     

Determination of In-Plane Anisotropy from Magnetoresistivity Measurements on YBa2Cu3O7−δ

The magnetoresistance of six untwinned YBa ₂ Cu ₃ O _7– crystals has been measured above T _c for IBc. Fluctuation theories allowing for an in-plane coherence length anisotropy ( _{a b} ) were used in the analyses. The results suggest that the anisotropy, = _b / _a , is considerably lower than that expected from the resistivity ratio, i.e., . Some magnetoresistive measurements with the field in the ab-plane are also presented.     

Engineered flux pinning centres in Pb-doped high temperature superconducting “Bi2Sr2CaCu2O8” ceramics

The Pb solubility of Bi₂Sr₂CaCu₂O₈ is determined within the concentration range Bi_2.18-x Pb _x Sr₂CaCu_8+d with 0 x 0.6 and the temperature range from 800 to 900°C. From a consideration of the Pb solubility in Bi₂Sr₂CaCu₂O₈ a simple annealing procedure was developed to precipitate (Pb,Bi)₄(Sr,Ca)₅Cu0_10+d (451 phase) in high-temperature superconducting Pb-rich Bi₂Sr₂CaCu₂O₈ ceramics. The precipitation results in a two-fold increase of the critical current density which is believed to express improved pinning properties of the superconducting ceramics. The microstructures of the samples with increased critical current density were studied with respect to the grain size and volume content of the 451 phase.     

Does Vortex Lattice of YBa2Cu3O6.94 in H⊥c Melt Below Intrinsic-Pinning Irreversibility Line?

Vortex lattice melting in the Hc configuration of an YBa ₂ Cu ₃ O _6.94 single crystal has been investigated by means of the ac susceptibility – i and the magnetic torque . The melting transition of vortex lattice occurs in Hc, too. Since the torque curve shows a sharp peak in the irreversible torque at _c 90° due to intrinsic pinning at lower temperatures, we can determine the irreversibility line for the intrinsic pinning. The melting transition in the Hc configuration appears at temperatures where the intrinsic-pinning peak is absent. We consider that the intrinsic pinning does not affect the nature of the vortex melting transition in the Hc configuration.     

Heat conduction in a multilayer composite wedge

A new method for analytically solving a problem of steady-state heat conduction for multilayer composite wedge-shaped bodies is suggested based on a generalization of the integral Mellin transform.Notation T temperature - _rr, thermal conductivity coefficients - thickness of composite material layers (1) - N₁(), N ₂ ⁽¹⁾ (), N ₂ ⁽²⁾ () auxiliary local functions from the rapid variable =r/ - m(r, p) auxiliary function entering the core of the generalized integral Mellin transform - ₀ half of the wedge aperture angle Moscow Institute of Chemical Engineering. Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 64, No. 4, pp. 487–491, April, 1993.     

Dielectric relaxation in polychlorotrifluoroethylene

The effect of increasing lamellar thickness in bulk polychlorotrifluoroethylene (PCTFE) by various methods (annealing and increasing time and temperature of crystallisation) on the parameters of the and relaxations has been studied.For the a relaxation consistent increase in temperature of maximum loss and activation energy with increasing lamellar thickness confirms the strong suggestion of earlier work [6] on oriented specimens and shows that the relaxation arises mainly in the interior of the lamellae with little contribution from the chain folds.No systematic changes in these parameters with increasing lamellar thickness was found for the relaxation and this is explained by the presence of _c and _a components in crystalline and amorphous regions respectively. The component _a (as well as the _c one) shows a marked anisotropy in magnitude with respect to the draw direction in oriented specimens relative to the direction of the applied electric field. This implies a lining up of the chain molecules parallel to one another in amorphous regions.The non-existence of analogous short chain compounds and experimental scatter prevented detailed checking of the consistency of the data for the relaxation with the theory for the _c-C _c model [5].     

Determination of the local angular radiation coefficients in certain two-body systems

A method is shown and formulas are derived by which local angular radiation coefficients can be determined in certain two-body systems where the configuration is arbitrary but one of the bodies is either a cylinder or a rectangular plate.Notation _int radiation vector of body 1 - _E ^int intrinsic radiation intensity of body 1 - _x, _y, _z components of the geometrical radiation vector along rectangular coordinates - r₀=x²+z² shortest distance from point M(x, y, z) to linear radiator - ₀ , ₀ ^' angles subtending the two segments of the linear radiator from point M(x, y, z) on area element 2 of irradiated surface - l length of the cylinders - x, y, z space coordinates of point M Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 22, No. 6, pp. 1080–1088, June, 1972.     

Magnetic oscillations in the quantized “mixed” state in first-kind superconductors

The suppression of superconductivity of the first kind in a hollow cylindrical superconductor by a strong electric current is studied on the basis of the linear time-dependent Ginzburg-Landau equations. Due to the presence of an electric field, mixed state consisting of superconducting fluctuations is established at the inner surface of the sample close to some critical current. When the inner radiusr ₁ of the cylinder is of the order of magnitude of the superconducting coherence length , the magnetic response to a longitudinal magnetic field H _a shows an oscillatory dependence of the magnetic flux onr ₁/ and H _a due to the quantum character of the macroscopic wave function. In the limiting situationsr ₁ andr ₁=0 we find again the paramagnetic and diamagnetic effect of the two- and one-dimensional mixed states respectively.     

Analysis of the complex impedance data for β-PbF2

Previously published complex impedance plots for the ionic conductor -PbF₂ show the familiar depressed circular arcs with an angle 0.7 /2 and an activation energy for the volume conductivity W _v=0.45 eV. A detailed analysis of this behaviour in terms of the recently developed non-Debye model shows the real part of the relative dielectric permittivity to have a frequency dependence ^0.7–1, with a high frequency limit of 50 Hz and with only weak dependence on temperature. The low-frequency spurs on the impedance plots are shown to indicate an interfacial barrier at each electrode having a similar non-Debye frequency characteristic to the bulk but showing a strong temperature dependence with an activation energy equal to W _v/2. This suggests the presence of low Debye-screened barriers of about k T height, resulting from depletion and accumulation of ionic carriers at incompletely transmitting electrodes. There is no visible effect of inter-grain boundaries on the flow of direct current.     

TEM study of metastable β-phase decomposition in rapidly solidified Ti-6Al-4V alloy

A new rationale is presented for various decomposition products obtained from the metastable -phase found in Ti-6A1-4V alloy produced by hot isostatic pressing comminuted melt-spun fibres and cooled to room temperature by furnace cooling. This alloy has an -matrix with about 8 vol% retained -phase, which is supersaturated with -stabilizers to such an extent that the martensitic transformation has been suppressed. The metastable -phase decomposes by different modes during continuous cooling, depending on the actual composition of individual -grains. Less enrichment of vanadium and iron favours the direct formation of the equilibrium -phase from the -matrix, while greater enrichment of vanadium and iron leads to a spinodal decomposition of the metastable -phase, resulting in a + two-phase structure. During further continuous cooling, the -phase which is lean in -stabilizers will transform into isothermal -phase. In addition, an unknown phase has also been observed in the -phase, which is typified by the appearance of 1/2{112} reflections in the SAD patterns.     

Flux Dynamics Effects in Superconducting Compacted Platinum Powders

We have performed measurements of the complex magnetic ac susceptibility of superconducting compacted platinum powders at temperatures 0.1T10 mK with different ac excitation frequencies in the interval 5 Hz/210 kHz and with different excitation field amplitudes at 0.006b_AC2 T. The dependence of the ac susceptibility on the excitation field amplitude permits to determine the intergranular critical current density j_c whereas the frequency dependence reflects the flux dynamics. By comparing the experimental results with theoretical predictions we identify flux flow, flux pinning and flux creep effects in the regimes of intra- and intergranular superconductivity. The possible impact of these effects on the superconducting parameters like j_c of the samples is discussed.     

Shear viscosity measurements of liquid 3He-4He mixtures above 0.5 K

Simultaneous measurements of () and of the molar volume are reported for liquid mixtures of ³He in ⁴He over the temperature range between 0.5 and 2.5 K. Here is the shear viscosity and is the mass density. In the superfluid phase, the product of the normal components, _n and _n , is measured. The mixtures with ³He molefractions 0.30 < X < 0.80 are studied with emphasis on the region near the superfluid transition T and near the phase-separation curve. Along the latter, they are compared with data by Lai and Kitchens. For X > 0.5, the viscosity singularity near T becomes a faint peak, which however fades into the temperature-dependent background viscosity as X tends to the tricritical concentration X _t. Likewise, no singularity in is apparent when T _t is approached along the phase separation branches _– and ₊. Furthermore, viscosity data are reported for ³He and compared with previous work. Finally, for dilute mixtures with 0.01 X 0.05, the results for are compared with previous data and with predictions.     

The crystallization of the amorphous alloy Fe40Ni40P14B6

The isothermal transformation behaviour of the metallic glass Fe₄₀Ni₄₀P₁₄B₆ between 320 and 400° C is described. Crystallization occurs by a eutectic mechanism to form Fe-Ni austenite and a body-centred tetragonal phase which is isomorphous with Fe₃P and Ni₃P. The eutectic crystals have a barrel shape such that the c-axis of the tetragonal phase is parallel to the barrel axis. The orientation relationship between the two phases is 1 1 0T 1 1 0 and 0 0 1T 1 1 2. The austenite phase contains (1 1 1) twins.     

Universality and the scaling laws in the superfluid phase transition of3He-4He mixtures

From the second-sound velocityU ₂ near the superfluid transition point, the superfluid densities in³He-⁴He mixtures, _s (X) and _s (), were deduced along the paths of constant³He concentrationX and of constant chemical potential difference of³He and⁴He. The following critical exponents of _s are determined: (a) =XX for _s (X) in the(X, T) plane,(b) X for _s (X) in the(, T) plane, and(c) for _s () in the(, T) plane. It is found that and _X change by about 4–6% relative to with increasing³He concentration up toX=0.4 and by 8–10% up toX=0.53. It seems that, belowX=0.53, universality hold for . Values of have been found to be in good agreement with the critical exponent of _s in pure⁴He under constant pressure. The values of and _X forX0.53 are also found to be consistent with the scaling relations in the (,T) plane of³He-⁴He mixture.Work performed in part while at the Electrotechnical Laboratory.