Needle-like nano hydroxyapatite/poly(l-lactide acid) composite scaffold for bone tissue engineering application

In this paper, a new nano-hydroxyapatite / poly (l-lactide acid) (nHAP/PLLA) composite scaffold comprising needle-like nHAP particles was prepared. In the first step, the identification and morphology of chemically synthesized HAP particles were determined by XRD, EDX, FTIR and SEM analyses. The needle-like nHAP particles with an average size of approximately 30–60 nm in width and 100–400 nm in length were found similar to needle-like bone nano apatites in terms of chemical composition and morphology. In the second step, nHAP and micro-sized HAP (mHAP) particles were used to fabricate HAP filled PLLA (HAP/PLLA) composites scaffolds using solid–liquid phase separation method. The porosity of scaffolds was up to 85%, and their average macropore diameter was in the range of 64–175 µm. FTIR and XRD analyses showed the presence of molecular interactions and chemical linkages between HAP particles and PLLA matrix. The compressive strength of nanocomposite scaffolds could high up to 8.46 MPa while those of pure PLLA and microcomposite scaffolds were 1.79 and 4.61 MPa, respectively. The cell affinity and cytocompatibility of the nanocomposite scaffold were found to be higher than those of pure PLLA and microcomposite scaffolds. Based on the results, the newly developed nHAP/PLLA composite scaffold is comparable with cancellous bone in terms of microstructure and mechanical strength, so it may be a suitable alternative for bone tissue engineering applications.     

OTS-modified HA and its toughening effect on PLLA/HA porous composite

In this paper, hydroxyapatite (HA) particles was modified with long-chain organic silane-Octadecyltrichlorosilane (OTS), and the modified particles were further used for preparing Poly(l-lactic acid) PLLA/HA porous composite. The modified particles were characterized by means of XRD, FTIR, and XPS techniques. Both XPS and FTIR results showed that OTS had been combined with HA, and the formation of P–O–Si bond, a covalent bond, on the HA particle surface was confirmed by XPS. OTS-modified HA particles were used to prepare porous composites by thermally induced phase separation method. The results showed that the composite had an interconnected pore structure with 100–300 μm macropores. With OTS dosage increasing during modification, the mechanical properties of PLLA/OTS-modified HA porous composites increased obviously. These results showed that OTS modification can effectively improve the interface compatibility between HA surface and PLLA.     

A polylactide/fibrin gel composite scaffold for cartilage tissue engineering: fabrication and an in vitro evaluation

A composite scaffold for cartilage tissue engineering was fabricated by filling a porous poly (l-lactide) (PLLA) scaffold with fibrin gel. The porous PLLA scaffold prepared by a method of thermally induced phase separation has an average pore diameter of 200 μm and a porosity of 93%. Incorporation of fibrin gel into the scaffold was achieved by dropping a fibrinogen and thrombin mixture solution onto the scaffold. For a couple of minutes the fibrin gel was in situ formed within the scaffold. The filling efficiency was decreased along with the increase of the fibrinogen concentration. After fibrin gel filling, the compressive modulus and the yield stress increased from 5.94 MPa and 0.37 MPa (control PLLA scaffold in a hydrated state) to 7.21 MPa and 0.53 MPa, respectively. While the fibrin gel lost its weight in phosphate buffered saline up to ~50% within 3 days, 85% and 70% of the fibrin gel weight in the composite scaffold was remained within 3 and 35 days, respectively. A consistent significant higher level of rabbit auricular chondrocyte viability, cell number and glycosaminoglycan was measured in the composite scaffold than that in the control PLLA scaffold. Rabbit auricular chondrocytes with round morphology were also observed in the composite scaffold by confocal microscopy and scanning electron microscopy. Altogether with the features of better strength and cytocompatibility, this type of composite scaffold may have better performance as a matrix for cartilage tissue engineering.     

相分离法构建聚乳酸/纳米羟基磷灰石复合纳米纤维支架及性能

通过液.液相分离法构建纳米纤维聚左旋乳酸/蚋米羟基磷灰石(NF-PLLA/nHA)仿生复合支架,利用扫描电镜、压缩测试、微量二喹啉甲酸(BCA)法、X射线衍射及差示扫描量热等手段对其进行表征.结果显示,nHA均匀馕嵌在PLLA纳米纤维间隙中,不影响其纳米纤维结构且明显提高力学性能.同时,nHA的引入还能增加对牛血清白蛋...     

Dispersions of carbon nanotubes/polyhedral oligomeric silsesquioxanes hybrids in polymer: the mechanical,electrical and EMI shielding properties

A hybrid was synthesized by grafting polyhedral oligomeric silsesquioxane (POSS) to multiwalled carbon nanotubes (MWCNTs). The MWCNT/polymer composites produced using silsesquioxane grafted MWCNTs as a filler had a high electromagnetic interference shielding effectiveness. Homogeneous dispersion of silsesquioxane grafted MWCNTs occurred throughout the polymer without any aggregation, while a pristine MWCNT aggregate that integrated several nanotube domains existed in the polymer matrix. A comparative study of the optical transmittance, electrical, and electromagnetic interference shielding properties of poly(l-lactide) (PLLA)/MWCNT composites based on pristine MWCNTs and silsesquioxane grafted MWCNTs was carried out. A high electromagnetic interference shielding effectiveness (15–16 dB) was obtained in the 36–50 GHz range at a relatively low filler loading (4 wt%) in the PLLA/silsesquioxane grafted MWCNT composite.     

介孔纳米羟基磷灰石/左旋聚乳酸复合材料的制备及性能

为考察介孔纳米羟基磷灰石(MHA)/左旋聚乳酸(PLLA)复合材料的性能,以十六烷基三甲基溴化铵(CTAB)为模板合成MHA,采用溶液相分离结合粒子沥滤法制备了不同纳米粒子含量的MHA/PLLA多孔支架复合材料,考察了其抗压缩性能和淬断面微观结构。采用溶液浇注法制备了MHA/PLLA复合膜,并对其拉伸性能和拉伸断面微观结构进行了研究。FTIR、XRD、TEM和氮气吸附测试等结果显示:合成的MHA具有典型的晶体结构、介孔结构和较高的比表面积。力学测试结果显示:在发生10%压缩形变时,填料含量为1%、5%和10%的MHA/PLLA多孔支架复合材料的抗压缩强度随填料含量增加而提高,与相应含量的纳米羟基磷灰石(HA)/PLLA多孔支架复合材料相比,分别提高了约37.0%、67.7%和144.7%。在填料含量为5%和10%时,MHA/PLLA复合膜的拉伸强度较HA/PLLA复合膜分别提高约38.7%和46.1%,拉伸模量分别提高约35.4%和14.5%。而且MHA/PLLA复合膜具有更高的断裂伸长率,填料含量为1%、5%和10%时断裂伸长率分别较HA/PLLA复合膜提高约91.3%、79.7%和96.1%。FESEM结果显示:尤其当填料含量较高时,MHA/PLLA多孔支架复合材料或复合膜中填料粒子分布较HA/PLLA中均匀。结果表明:与HA/PLLA复合材料相比,随着MHA含量增加,MHA/PLLA复合材料具有更好的力学性能,MHA在PLLA基体中分布相对更均匀。     

Nucleation and growth mechanism of apatite on a bioactive and degradable ceramic/polymer composite with a thick polymer layer

Nucleation and growth mechanism of apatite on a bioactive and degradable PLLA/SiO₂–CaO composite with a thick PLLA surface layer were investigated compared to that on a bioactive but non-degradable polyurethane (PU)/SiO₂–CaO composite with a thick PU surface layer. The bioactive SiO₂–CaO particles were made by a sol–gel method from tetraethyl orthosilicate and calcium nitrate tetrahydrate under acidic condition followed by heat treatment at 600 °C for 2 h. The PLLA/SiO₂–CaO and PU/SiO₂–CaO composites were then prepared by a solvent casting method which resulted in thick PLLA and PU surface layers, respectively, due to precipitation of SiO₂–CaO particles during the casting process. Two composites were exposed to SBF for 1 week and this exposure led to form uniform and complete apatite coating layer on the PLLA/SiO₂–CaO composite but not on the PU/SiO₂-CaO composite. These results were interpreted in terms of the degradability of the polymers. A practical implication of the results is that a post-surface grinding or cutting processes to expose bioactive ceramics to the surface of a composite with a thick biodegradable polymer layer is not required for providing apatite forming ability, which has been considered as one of the pragmatic obstacles for the application as a bone grafting material.     

Fabrication of bioactive composite by developing PLLA onto the framework of sintered HA scaffold

Composite porous scaffolds of hydroxyapatite (HA)/poly-l-lactide (PLLA) were fabricated by a two-step immersing replication method. Structure and mechanical properties of both the single HA scaffold and the composite HA/PLLA scaffold were determined. The bioactivity of the scaffolds was evaluated by soaking in a simulated body fluid (SBF), and the formation of the apatite layer was determined by X-ray diffraction (XRD), Scanning Electron Microscope (SEM) and Energy-Dispersive Spectrometer (EDS). The results showed that without changing the highly interconnected porous structure, the HA/PLLA composite scaffold was mechanically enhanced to a great deal of extent compared with single HA scaffold. On the other hand, it is also suggested that the HA/PLLA scaffold was bioactive as it induced the formation of apatite on the surface of the composite scaffolds after soaking in SBF for 7 days.     

A novel method for the fabrication of homogeneous hydroxyapatite/collagen nanocomposite and nanocomposite scaffold with hierarchical porosity

Homogeneous nanocomposites composed of hydroxyapatite (HAp) and collagen were synthesized using a novel in situ precipitation method through dual template-driven. The morphological and componential properties of nanocomposites were investigated. The HAp particulates, in sizes of about 50–100 nm, were distributed homogeneously in the organic collagen hydrogel. Highly magnified TEM observation showed that HAp inorganic particles were composed of fine sub-particles (2–5 nm) without regular crystallographic orientation. Based on these homogeneous nanocomposites, a novel HAp/collagen nanocomposite scaffold with hierarchical porosity was prepared by multilevel freeze-drying technique. Compared to other conventional scaffolds for tissue engineering, this novel in situ method endows synthesized composite scaffolds with unique morphology—ultrafine HAp particles dispersed homogenously in collagen at nano level and the foam scaffold with hierarchical pore structures. The mechanical performance increased obviously compared with neat collagen. These results provided an efficient approach toward new biomimetic tissue scaffold for the biomedical applications with enhanced intensity/bioactivity and controlled resorption rates. This novel method, we expect, will lead to a wide application in many other hydrogel systems and may be useful for fabrication of various homogeneous inorganic/organic nanocomposites.     

An approach to architecture 3D scaffold with interconnective microchannel networks inducing angiogenesis for tissue engineering

The angiogenesis of 3D scaffold is one of the major current limitations in clinical practice tissue engineering. The new strategy of construction 3D scaffold with microchannel circulation network may improve angiogenesis. In this study, 3D poly(d,l-lactic acid) scaffolds with controllable microchannel structures were fabricated using sacrificial sugar structures. Melt drawing sugar-fiber network produced by a modified filament spiral winding method was used to form the microchannel with adjustable diameters and porosity. This fabrication process was rapid, inexpensive, and highly scalable. The porosity, microchannel diameter, interconnectivity and surface topographies of the scaffold were characterized by scanning electron microscopy. Mechanical properties were evaluated by compression tests. The mean porosity values of the scaffolds were in the 65–78% and the scaffold exhibited microchannel structure with diameter in the 100–200 μm range. The results showed that the scaffolds exhibited an adequate porosity, interconnective microchannel network, and mechanical properties. The cell culture studies with endothelial cells (ECs) demonstrated that the scaffold allowed cells to proliferate and penetrate into the volume of the entire scaffold. Overall, these findings suggest that the fabrication process offers significant advantages and flexibility in generating a variety of non-cytotoxic tissue engineering scaffolds with controllable distributions of porosity and physical properties that could provide the necessary physical cues for ECs and further improve angiogenesis for tissue engineering.     

Fabrication of high conductivity dual multi-porous poly (l-lactic acid)/polypyrrole composite micro/nanofiber film

Dual multi-porous PLLA (poly(l-lactic acid))/H₂SO₄-doped PPy (polypyrrole) composite micro/nano fiber films were fabricated by combining electrospinning with in situ polymerization. The morphologies and structures of the resulting samples were analyzed by scanning electron microscopy (SEM). It was found that the composite micro/nano fibers exhibited a core-shell structure and the composite fiber film had a dual multi-pore structure composed of pores both in the fibers and among the fibers. Semiconductor parameter analyzer was used to characterize the electrical properties of the samples. It was interesting to find that all the PLLA/H₂SO₄-doped PPy composite micro/nano fiber films had higher conductivity than H₂SO₄-doped PPy particles when the polymerization time up to 180 min. Effects of the pyrrole synthesis conditions on the pore size and the conductivity of PLLA/PPy composite fiber film were assessed. By optimizing the polymerization conditions, the max conductivity of this composite fiber film was about 179.0 S cm⁻¹ with a pore size of about 250 μm. The possible mechanism of PLLA/H₂SO₄-doped PPy composite micro/nano fiber films had much higher conductivity than H₂SO₄-doped PPy particles was discussed.     

In vitro study of drug-eluting stent coatings based on poly(<Emphasis Type="SmallCaps">l</Emphasis>-lactide) incorporating cyclosporine A – drug release,polymer degradation and mechanical integrity

In this study, absorbable polymer stent coatings for localized drug delivery based on poly(l-lactide) (PLLA) and cyclosporine A (CsA) were developed and tested in vitro. Metallic stents were coated with different compositions of PLLA/CsA (70/30, 60/40, 50/50% w/w) and β-sterilized. The specimens were used to assess the drug release kinetics with HPLC. Sterilization influenced polymer degradation was measured with GPC. Mechanical integrity of the stent coatings was studied with SEM. The interconnection of the coated stents with a balloon-catheter was characterized by the measurement of stent dislodgment force. A migration assay was used to determine the inhibitory effect of the model drug CsA on smooth muscle cell (SMC) migration. The release of CsA was established over time periods up to 24 days in sodium chloride solution and in porcine blood plasma. An inhibition of SMC migration (max. 26–33%) was found for CsA concentrations of 4 × 10⁻⁵ to 4 × 10⁻⁷ mol/l. Marked molecular weight reduction (70–80%) of the PLLA matrix occurred after β-sterilization. We also observed a substantial decrease of in vitro degradation time. The maintenance of the mechanical integrity of the polymer coating during crimping and dilation of the specimens could be verified, and a sufficient stent dislodgment force of 0.8–0.9 N was measured.     

Synthesis and morphology of new functional polyimide/titania nano hybrid materials

The synthesis and full characterization of 3,5-diamino-N-(1-oxo-3-phenyl-1-(phenylamino)propan-2-yl)benzamide (5), as a new diamine monomer containing l-phenylalanine fractions in the structure of pendant group is presented. The stated diamine is employed as a key monomer for the in situ sol–gel fabrication of polyimide/titania nano hybrid thin films containing different titania contents. It is shown that titania particles are created in the size range of 20–80 nm, well-dispersed and enjoy the favorable spherical shapes supposing the constructive organic–inorganic interactions. The superior thermal stabilities of resulted nanocomposite films are confirmed using thermal analysis techniques. Moreover, the UV–Vis spectroscopy has shown the growing up in blocking efficiency along with the increase in titania contents. Predictably, the produced titania nanoparticles have amorphous structures.     

How hybridization with zinc oxide whiskers and carbon fibers affects the thermal diffusivity and mechanical properties of poly(<Emphasis Type="SmallCaps">l</Emphasis>-lactic acid) nanocomposites

The enhanced thermal diffusivity and mechanical properties of poly(l-lactic acid) (PLLA) nanocomposites reported here are based on the percolation network formed when PLLA is hybridized with short carbon fibers (CFs) and functionalized zinc oxide whiskers. The PLLA nanocomposite containing 30 wt% (≈9.5 vol%) ZnO whiskers and 10 wt% (≈8.1 vol%) CFs had a thermal diffusivity almost as high as that of stainless steel and an insulator-level electrical resistivity (>10¹⁰ Ωm). Modifying the surface of the ZnO whiskers by esterifying them using specific alcohols with long linear alkyl chains improved the elastic strength and toughness of the nanocomposites significantly. These results suggest that hybridizing PLLA with short CFs and functionalized ZnO whiskers yields nanocomposites with high thermal diffusivity as well as high electrical resistivity and excellent mechanical properties.     

Enhancement of thermal diffusivity of poly(<Emphasis Type="SmallCaps">l</Emphasis>-lactic acid) composites with a net-like structure of carbon fibers

Thermally conductive carbon fiber/poly(l-lactic acid) (PLLA) composites were made by using fatty acid amides as binders to form a net-like structure of carbon fibers in them, aiming at achieving high thermal diffusivity of the composites with a small amount of the fibers and facilitating their processing without much cost. Infrared thermography analysis of composites with varying the size of carbon fibers and controlling the solubility parameters of fatty acid amides in them revealed that the composite with 10 wt% of 6 mm-long carbon fiber and 5 wt% of N,N′-ethylene bis-olearamide had a thermal diffusivity comparable to that of stainless steel (SUS304). This high thermal diffusivity was due to percolation networks of long carbon fibers bound by the specific low-polarity amide in the composite.     

纳米羟基磷灰石/聚酰胺6医用复合材料的制备及性能表征

为防止纳米羟基磷灰石(nano HAP)粉末的团聚,采用溶剂沉淀法制备了nano HAP/聚酰胺6(PA6)复合粉末,并对粉末进行热压成型制得nano HAP/PA6复合材料。然后,通过FTIR、XRD和SEM对nano HAP/PA6复合材料的成分、结构和形貌进行了表征,并对复合材料的热稳定性、力学性能和细胞相容性进行了检测。结果表明:所制备的nano HAP/PA6复合材料结晶体大小均匀,且PA6只存在α型结晶;由于nano HAP与PA6界面上形成新的氢键和COO—Ca,复合材料具有良好的综合性能;在低于350℃时,nano HAP/PA6复合材料不会发生裂解,力学性能与人骨匹配,50wt%nano HAP/PA6复合材料的弯曲强度、压缩强度和弹性模量分别为146.87MPa、98.44MPa和5.44GPa。MG-63骨瘤细胞在nano HAP/PA6复合材料表面粘附和生长状况良好,说明nano HAP/PA6复合材料具有良好的细胞相容性。所得结论表明nano HAP/PA6复合材料在骨修复方面具有应用价值。     

Emulsion electrospun vascular endothelial growth factor encapsulated poly(<Emphasis Type="SmallCaps">l</Emphasis>-lactic acid-<Emphasis Type="Italic">co</Emphasis>-ε-caprolactone) nanofibers for sustained release in cardiac tissue engineering

Emulsion electrospinning is a novel approach to fabricate core–shell nanofibers, and it is associated with several advantages such as the alleviation of initial burst release of drugs and it protects the bioactivity of incorporated drugs or proteins. Aiming to develop a sustained release scaffold which could be a promising substrate for cardiovascular tissue regeneration, we encapsulated vascular endothelial growth factor (VEGF) with either of the protective agents, dextran or bovine serum albumin (BSA) into the core of poly(l-lactic acid-co-ε-caprolactone) (PLCL) nanofibers by emulsion electrospinning. The morphologies and fiber diameters of the emulsion electrospun scaffolds were determined by scanning electron microscope, and the core–shell structure was evaluated by laser scanning confocal microscope. Uniform nanofibers of PLCL, PLCL–VEGF–BSA, and PLCL–VEGF–DEX with fiber diameters in the range of 572 ± 92, 460 ± 63, and 412 ± 61 nm, respectively were obtained by emulsion spinning. The release profile of VEGF in phosphate-buffered saline for up to 672 h (28 days) was evaluated, and the scaffold functionality was established by performing cell proliferations using human bone marrow derived mesenchymal stem cells. Results of our study demonstrated that the emulsion electrospun VEGF containing core–shell structured PLCL nanofibers offered controlled release of VEGF through the emulsion electrospun core–shell structured nanofibers and could be potential substrates for cardiac tissue regeneration.     

In vitro behavior of osteoblast-like cells on PLLA films with a biomimetic apatite or apatite/collagen composite coating

To investigate the methods to improve the cell–material interaction of devices or tissue engineering scaffolds made of poly(l-lactic acid) (PLLA) polymer, apatite and apatite/collagen composite coatings were formed on PLLA films within 24 h through accelerated biomimetic processes. In vitro investigation using Saos-2 osteoblast-like cells through cell culture was conducted to assess the biological performance of these biomimetic coatings. The cell morphology on three types of surfaces, viz., PLLA film, PLLA film with the apatite coating, and PLLA film with the apatite/collagen composite coating, was studied using scanning electron microscopy (SEM). Cell viability was estimated using the MTT assay. The differentiated cell function was assessed by measuring the alkaline phosphatase (ALP) activity. The results obtained indicated that the biomimetic apatite and apatite/collagen composite coatings could significantly enhance the proliferation and differentiation of osteoblast-like cells. The apatite/collagen composite coating appears to be promising for the surface modification of PLLA-based devices with much improved interactions with osteoblastic cells.     

Fabrication and in vivo osteogenesis of biomimetic poly(propylene carbonate) scaffold with nanofibrous chitosan network in macropores for bone tissue engineering

A biomimetic poly(propylene carbonate) (PPC) porous scaffold with nanofibrous chitosan network within macropores (PPC/CSNFs) for bone tissue engineering was fabricated by a dual solid–liquid phase separation technique. PPC scaffold with interconnected solid pore wall structure was prepared by the first phase separation, which showed a high porosity of 91.9% and a good compressive modulus of 14.2 ± 0.56 MPa, respectively. By the second phase separation, nanofibrous chitosan of 50–500 nm in diameter was formed in the macropores with little influence on the pore structure and the mechanical properties of PPC scaffold. The nanofibrous chitosan content was calculated to be 9.78% by elemental analysis. After incubation in SBF for 14 days, more apatite crystals were deposited on the pore surface as well as the nanofibrous chitosan surface of PPC/CSNFs scaffold compared with PPC scaffold. The in vitro culture of bone mesenchymal stem cells showed that PPC/CSNFs scaffold exhibited a better cell viability than PPC scaffold. After implantation in rabbits for 16 weeks, the defect was entirely repaired by PPC/CSNFs scaffold, as opposed to the incomplete healing for PPC scaffold. It indicated that PPC/CSNFs scaffold showed a faster in vivo osteogenesis rate than PPC scaffold. Hereby, PPC/CSNFs scaffold will be a potential candidate for bone tissue engineering.     

Effect of ceramic filler content on the mechanical and thermal behaviour of poly-<Emphasis Type="SmallCaps">l</Emphasis>-lactic acid and poly-<Emphasis Type="SmallCaps">l</Emphasis>-lactic-co-glycolic acid composites for medical applications

One main application of resorbable poly-l-lactic acid (PLLA) and poly-l-lactic-co-glycolic acid (PLGA) based materials is in medical implants. In this study composites were made from PLLA and PLGA with hydroxyapatite (HAp) respective β-tricalcium phosphate (β-TCP) fillers. The filler content and particle size were varied, and the thermal properties as well as the mechanical strength of the composites were investigated. The composites were made by an extrusion compounding process giving 2–2.5 mm diameter sized profiles. The results verified that the thermal stability of the composites was reasonable during the optimized compounding conditions. Scanning electron microscopy revealed that the fillers were well dispersed in the polymer matrices. The mechanical properties were improved by the addition of the fillers. The optimum mechanical properties for the extruded profiles were obtained with the HAp fillers. The E-modulus was increased from 3.3 to 4.6 GPa by addition of filler particles (30 wt%) whereas the flexural strength was reduced from 133 to 106 MPa.