Experiments on In-Store Paddy Drying Under Tropical Climate: Simulation and Product Quality

Abstract

The main objective of this work is to study the rice whiteness and paddy qualities of rice in terms of hardness, stickiness, cohesiveness, and germination of rice. The prediction results of moisture content and whiteness are compared with the experimental results using a near-equilibrium drying model, which is modified by including whiteness kinetics of rice kernel. The long grain rice (Suphanburi 1 high amylose indica variety), which consists of 27% amylose was used for all experiments. The experiments were carried out at the average ambient temperature range of 28.6–30.8°C, average relative humidity of 65.2–80.6% with a fixed bed depth of 1.0 m. Specific air flow rates of 0.65 and 0.93 m³/min-m³ of paddy were forced continuously through the paddy bulk at initial moisture contents of 18.5% and 20.1% wet basis, respectively. The desired final moisture content of paddy is about 13.3 ± 0.6% wet basis. The results show that drying rate and the whiteness predictions are in good agreement with those from the experiments. The in-store drying using ambient air condition did not produce notable effect on the rice whiteness, head rice yield, and the percentage of paddy germination. However, the hardness, stickiness, and cohesiveness of rice were changed.     

A Superheated-Steam Fluidized-Bed Dryer for Parboiled Rice: Testing of a Pilot-Scale and Mathematical Model Development

This article describes the testing of a pilot-scale superheated-steam fluidized-bed dryer for parboiled rice along with development of a mathematical model for predicting the changes in temperature of steam and moisture content of parboiled rice during drying. Based on the obtained results, it was found that the superficial velocity of steam from 1.3 to 1.5 times of the minimum fluidization velocity had no significant effect on the drying rates of rice. The energy consumption for reducing the moisture content of paddy from 0.43 to 0.22 kg/kg dry basis was approximately 7.2 MJ/kg water evaporated. Drying temperature caused the appreciable change of parboiled rice qualities as characterized by water adsorption, whiteness and pasting viscosities, white belly, and hardness. Soaking paddy at a temperature of 70°C for 7-8 h before drying was sufficiently enough for producing parboiled rice, with no white belly. The gelatinization of starch during drying resulted in higher head rice yield of the product as compared to that of raw paddy.     

Comparison of Drying Kinetics of Paddy Using a Pneumatic Conveying Dryer with and without a Cyclone

The objective of the present work is to find the possibility of reducing the high initial moisture content of wet paddy using a small-scale, low-cost pneumatic conveying dryer that can be provided for each farming household. The dryer without a cyclone equipped at the exit of the dryer is studied and the data obtained from this system is compared with those obtained previously from the dryer with a cyclone. Parametric effects of the following variables are examined: velocity of drying air from 20 to 30 m/s, feed rate of rough rice from 150 to 350 kg/h, and drying air temperature from 35 to 70°C. From the experimental results it is found that the drying process with and without a cyclone are able to lead to very rapid drying without any grain quality problems such as cracks in the rice kernel. For the same experimental conditions, the cyclone-equipped dryer gives around 1% higher decrease of moisture content, 2°C higher average surface temperature of paddy, 3-4% higher average percentage of head rice yield, and 2 kg/h higher average evaporation rate. However, the energy consumption per evaporated mass of water is 20-30% lower than the non-cyclone-equipped dryer.     

A Small-Scale Pneumatic Conveying Dryer of Rough Rice

This article studies the possibility of reducing the high initial moisture content of wet rough rice using a small-scale low-cost pneumatic conveying dryer as a first stage dryer. The parameters investigated are final moisture content, surface temperature of rough rice, head rice yield, drying rate, power consumption per unit mass of evaporated water, and physical characteristics of rice. Parametric effects of the following variables are examined: velocity of drying air from 20 to 30 m/s, feed rate of rough rice from 150 to 350 kg/h, initial moisture content from 22 to 26% (wet basis), and drying air temperature from 35 to 70°C. From the experimental results, it is found that this drying method can be used for fresh rough rice with an initial moisture content of over 24% (wet basis). The drying process is able to lead to very rapid drying without any grain quality problems such as cracks in the rice kernel. The moisture content can be reduced to approximately 18% (wet basis) or about 5-6% of the initial moisture content within 3-4 s. The optimal drying air temperature is in the range of 50 to 60°C. A comparison of pneumatic conveying drying data obtained from the present study with fluidized bed drying data reported in the open literature is also discussed.     

MANAGING MOIST PADDY BY DRYING, TEMPERING AND AMBIENT AIR VENTILATION

This paper describes a strategy for reducing moisture in paddy by fluidized bed drying, tempering and ambient air cooling. Experimental results showed that after the three processes, moisture content was reduced from 33 % to 16.5 % dry-basis within approximately 53 minutes. During the first process, a fluidized-bed dryer was used to reduce the moisture content of paddy down to 19.5 % dry-basis within 3 minutes. Then the paddy was tempered for 30 minutes. Finally, it was cooled by ambient air (temperature and relative humidity of 30 °C and 55-60% respectively) with air velocity of 0.15 m/s for 20 minutes. Quality of paddy in terms of head rice yield and whiteness was acceptable.     

Drying Characteristics of Malaysian Paddy: Kinetics & Grain Cracking Quality

Drying kinetics of Malaysian paddy dried in a laboratory scale batch rapid bin dryer was studied. Quality of paddy after drying at temperatures of 60 and 80°C, bed heights of 2 and 4 cm, and at different drying stages was presented in terms of cracking percentage. Moisture content of paddy reduced exponentially with time and became stable at equilibrium moisture content. Characteristic drying rate curves exhibited mainly falling rate period, with an induction period in deep beds, but without the constant rate period. A custom-made light box was built to visually analyze the cracking in paddy kernel. The extent of breakage is directly related to the crack percentage. The percentage of cracks increased with drying and tempering temperatures and was higher after 2 weeks of storage before milling. Bed heights did not significantly affect the head rice yield as much as tempering between two drying stages. Temperatures above 80°C caused severe cracking in paddy kernel and produced miserable yield of head rice after milling, which could be slightly improved by tempering. The use of a proper miller is also important in ensuring good head yield results and whiteness quality.     

Effect of Fluidized Bed Drying Temperature on Various Quality Attributes of Paddy

Abstract

As reported by many researchers, it was found that fluidized bed paddy drying using high drying air temperatures of over 100°C affected the head rice yield and whiteness of dried rice. However, only a few studies on fluidized bed paddy drying with drying air temperatures below 100°C were so far reported. The main objective of this work was therefore to study the effect of fluidized bed drying air temperature on various quality parameters of Suphanburi 1 and Pathumthani 1 Indica rice. Paddy was dried from the initial moisture contents of 25.0, 28.8, and 32.5% dry basis to 22.5 ± 1.2% dry basis using inlet drying air temperatures between 40 and 150°C at 10°C/step. After fluidized bed drying, paddy was tempered and followed by ambient air aeration until its final moisture content was reduced to 16.3 ± 0.5% dry basis. The results showed that the head rice yield of Suphanburi 1 was significantly related to the inlet drying temperature and initial moisture content whilst there was no significant relationship between the head rice yield, drying temperature and initial moisture content for Pathumthani 1. The whiteness of the two rice varieties was slightly decreased with increase in drying air temperature and initial moisture content. It was also found that the hardness of both cooked rice varieties exhibited insignificant difference (p < 0.05) comparing to rewetted rice, which was gently dried by ambient air aeration in thin layer. The thermal analysis by DSC also showed that partial gelatinization occurred during drying at higher temperatures. Using inlet drying air temperatures in the range of 40–150°C therefore did not affected the quality of cooked rice and paddy. The milling quality of paddy was also well maintained.     

Effect of Pulsed Electric Field and Osmotic Dehydration Pretreatment on the Convective Drying of Carrot Tissue

The influence of pulsed electric field (PEF) and subsequent centrifugal osmotic dehydration (OD) on the convective drying behavior of carrot is investigated. The PEF was carried out at an intensity of E = 0.60 kV/cm and a treatment duration of t_PEF = 50 ms. The following centrifugal OD was performed in a sucrose solution of 65% (w/w) at 40°C for 0, 1, 2, or 4 h under 2400 × g. The drying was performed after the centrifugal OD for temperatures 40-60°C and at constant air rate (6 m³/h).

With the increase of OD duration the air drying time is reduced spectacularly. The dimensionless moisture ratio Xr = 0.1 is reached for PEF-untreated carrots after 370 min of air drying at 60°C in absence of centrifugal OD against 90 min of air drying after the 240 min of centrifugal OD. The PEF treatment reduces additionally the air drying time. The total time of dehydration operations can be shortened when OD time is optimized. For instance, the minimal time required to dehydrate untreated carrots until Xr = 0.1 is 260 min (120 min of OD at 40°C and 140 min of drying at 60°C). It is reduced to 230 min with PEF-treated carrots.

The moisture effective diffusivity D_eff is calculated for the convective air drying based on Fick's law. The centrifugal OD pretreatment increases drastically the value of D_eff. For instance, 4 h of centrifugal OD permitted increasing the value of D_eff from 0.93 · 10^-9 to 3.85 · 10^-9 m²/s for untreated carrots and from 1.17 · 10^-9 to 5.10 · 10^-9 m²/s for PEF-treated carrots.     

MOBILE FLUIDIZED BED PADDY DRYER

The objectives of this research are to design, construct and test a mobile fluidized bed paddy dryer with a drying capacity of 2.5-4.0 t/h. Suitable drying conditions are recommended as follows : drying capacity 3.8 t/h, bed velocity 2.8 m/s, average drying air temperature 144 °C, bed height 13.5 cm, fraction of air recycled 0.8. Residence time of paddy was approximately 1.3 minutes. Test results showed that moisture content of paddy was reduced from 32.6 % dry-basis to 25.8 % dry-basis. Consumption of electrical power and diesel fuel was 12.9 kW and 21.71 1/h respectively. Primary energy consumption was 910.9 MJ/h. The dryer could evaporate water 218.8 kg/h. Specific primary energy consumption was 4.2 MJ/kg-water evaporated. Cost of paddy drying was 1.48 baht/kg-water evaporated of which 0.53 was fixed cost and 0.95 was energy cost (US$1 =34baht).     

EFFECT OF TEMPERING ON SUBSEQUENT DRYING OF PADDY USING FLUIDISATION TECHNIQUE

Drying and tempering models for paddy drying by a fluidised bed technique have been developed to describe the moisture movement inside a single paddy kernel. The grain shape was considered as a finite cylinder. The internal diffusion is an important contribution to control the drying rate of paddy. The dependence of effective diffusion coefficient on drying temperature can be adequately explained based on Arrhenius form. The parameters of this equation were evaluated in the range of temperatures between 110°C and 170°C by using the regression analysis with 189 experimental drying data. As compared with no tempering, the faster drying rate can be obtained by tempering treatment between drying stages. The effect of degrees of tempering on determining the moisture reduction in the second stage has also been explored. According to the simulation results, a prediction equation of the required tempering time for the tempering index of 0.95 has been established in which the drying air temperature, initial moisture content and drying time are taken into account. The tempering time for 35 min is recommended for the continuous fluidised bed dryers being operated in rice mills.     

Application of Bi-S Drying Correlation to Microwave Drying Data of Pharmaceutical Powders

The moisture diffusivities and moisture transfer coefficients characterising the drying of pharmaceutical powders were determined using a correlation proposed by Dincer et al. (2002, Development of a new drying correlation for practical applications. International Journal of Energy Research 26, 245-251). Experimental moisture content data for lactose, Aspirin and Paracetamol samples dried under convective, microwave, combined convective-microwave and combined vacuum-microwave conditions were obtained. The drying coefficients and lag factors were determined from the experimental measurements and incorporated into the model. The mass transfer Bi numbers were found to be in the range 0.058 to 0.194, indicating the presence of finite internal and external resistances. Moisture diffusivity and diffusion coefficient values in the range 0.135 × 10^-9 to 102 × 10^-9 m² s^-1 and 0.067 × 10^-7 to 8.21 × 10^-7 ms^-1 respectively, were calculated. The predicted moisture profiles showed adequate agreement with the experimental observations, with the average error between experimental and predicted results being ± 15.9%.     

Surface Stickiness of Drops of Carbohydrate and Organic Acid Solutions During Convective Drying: Experiments and Modeling

Drying kinetics of low molecular weight sugars such as fructose, glucose, sucrose and organic acid such as citric acid and high molecular weight carbohydrate such as maltodextrin (DE 6) were determined experimentally using single drop drying experiments as well as predicted numerically by solving the mass and heat transfer equations. The predicted moisture and temperature histories agreed with the experimental ones within 6% average relative (absolute) error and average difference of ± 1°C, respectively. The stickiness histories of these drops were determined experimentally and predicted numerically based on the glass transition temperature (T_g) of surface layer. The model predicted the experimental observations with good accuracy. A nonsticky regime for these materials during spray drying is proposed by simulating a drop, initially 120 µm in diameter, in a spray drying environment.     

A Study of the Limitations to Spray Dryer Outlet Performance

The concept of the product moisture locus was tested in this work using a pilot-scale modified Niro spray dryer (diameter 0.8 m, height 2 m), where the residence time of the particles inside this spray dryer is lower compared with larger industrial spray dryers. The moisture contents of skim milk powder produced from spray drying skim milk (solids content 8.8% w/v) at different operating conditions, namely different swirl vane angles (0°, 25°, 30°), inlet air temperatures (170°C, 200°C, 230°C) and process fluid flowrates (1.4 kg h^-1, 1.6 kg h^-1, 1.8 kg h^-1), were compared with the predicted equilibrium moisture contents. In addition, the residence time of the particles was also increased in the spray dryer by decreasing the inlet air mass flowrate from 0.016 to 0.013 kg s^-1. The outlet moisture contents of the skim milk powder for all the 23 runs carried out in this work were within 0.4% of the equilibrium values. Thus, the skim milk powder particles were in close equilibrium with the gas inside the drying chamber. These equilibrium limitations are confirmed by other literature data (Boonyai, P. Comparative Evaluation of Soymilk Drying in a Spray Dryer and Spouted Bed of Inert Particles. M.Sc. Thesis. Asian Institute of Technology: Bangkok, Thailand, 2000; 90 pp; Harvie, D.J.E.; Langrish, T.A.G.; Fletcher, D.F. A computational fluid dynamics study of a tall-form spray dryer. Trans IChemE 2002, in press). The use of this finding to predict spray dryer performance is demonstrated by mass and energy balance calculations.     

Drying Characteristics of Barley Grain Dried in a Spouted-Bed and Combined IR-Convection Dryers

A study was performed to determine the drying characteristics and quality of barley grain dried in a laboratory scale spouted-bed dryer at 30, 35, 40, and 45°C and an inlet air velocity of 23 m/s^-1, and in an IR-convection dryer under an infrared radiation intensity of 0.048, 0.061, 0.073, and 0.107 W cm^-2 at an air velocity of 0.5 m/s^-1. The results show that the first, relatively short, phase of a sharp decrease in the drying rate was followed by the phase of a slow decrease. The time of barley drying depended on temperature of inlet air in a spouted-bed dryer and on radiation intensities in an IR-convection dryer. Barley drying at 45°C in a spouted-bed dryer was accompanied by the lowest total energy consumption. The average specific energy consumption was lower and the average efficiency of drying was higher for drying in a spouted-bed dryer. The effective diffusivities were in the range 2.20-4.52 × 10^-11 m² s^-1 and 3.04-4.79 × 10^-11 m²/s^-1 for barley dried in a spouted-bed and in an IR-convection dryer, respectively. There were no significant differences in kernel germination energy and capacity between the two drying methods tested.     

MANAGING MOIST PADDY BY DRYING,TEMPERING AND AMBIENT AIR VENTILATION

ABSTRACT

This paper describes a strategy for reducing moisture in paddy by fluidized bed drying, tempering and ambient air cooling. Experimental results showed that after the three processes, moisture content was reduced from 33 % to 16.5 % dry-basis within approximately 53 minutes. During the first process, a fluidized-bed dryer was used to reduce the moisture content of paddy down to 19.5 % dry-basis within 3 minutes. Then the paddy was tempered for 30 minutes. Finally, it was cooled by ambient air (temperature and relative humidity of 30 °C and 55-60% respectively) with air velocity of 0.15 m/s for 20 minutes. Quality of paddy in terms of head rice yield and whiteness was acceptable.     

The Effect of Moisture Content on the Conversion of Ergosterol to Vitamin D in Shiitake Mushrooms

The distribution of ergosterol in different parts of shiitake mushrooms was studied in order to optimize the conversion of ergosterol to vitamin D₂ during drying. The effect of moisture on the conversion of ergosterol to vitamin D₂ was also investigated by adjusting the moisture content of fresh mushrooms to different levels in a large vacuum desiccator and subjecting them to UV irradiation at 290-320 nm wavelength, for 2 h. The moisture, ergosterol and vitamin D₂ contents were determined using standard procedures. It was found that the ergosterol content on a dry matter basis of fresh shiitake mushroom was highest in the gills (10.6 ± 0.99 mg/g DM), followed by the cap or pileus (5.34 ± 0.64 mg/g DM) and was least in the stalk or stipe (2.97 ± 0.56). The moisture content had a marked influence on the conversion of ergosterol to vitamin D₂, the best conversion taking place at a moisture content of about 70% on a wet basis.     

Rapid Drying of Parboiled Paddy Using Hot Air Impinging Stream Dryer

A method for rapid drying of parboiled paddy via the use of an impinging stream dryer was proposed and assessed. The effects of the drying air temperature, number of drying cycles, as well as time of tempering between each drying cycle on the moisture reduction, head rice yield, and whiteness index of the dried parboiled paddy were studied. The drying experiments were carried out at drying air temperatures of 130, 150, and 170°C; inlet air velocity of 20 m/s; impinging distance of 5 cm; and paddy feed rate of 40 kg_{dry_paddy}/h. Parboiled paddy was dried for up to seven cycles. Between each drying cycle the parboiled paddy was tempered for a period of either 0 (no tempering), 15, 30, 60, or 120 min. After impinging stream drying, paddy was ventilated by ambient air flow until its moisture content reached 16% (db). Moisture reduction of the paddy was noted to depend on both the impinging stream drying temperature and tempering time. Drying at a high temperature along with tempering for a suitable period of time could maintain the head rice yield of the paddy at a level similar to that of the reference parboiled paddy. To avoid discoloration and low head rice yield, parboiled paddy should not be dried at a temperature higher than 150°C and should be tempered for at least 30 min.     

A Superheated-Steam Fluidized-Bed Dryer for Parboiled Rice: Testing of a Pilot-Scale and Mathematical Model Development

This article describes the testing of a pilot-scale superheated-steam fluidized-bed dryer for parboiled rice along with development of a mathematical model for predicting the changes in temperature of steam and moisture content of parboiled rice during drying. Based on the obtained results, it was found that the superficial velocity of steam from 1.3 to 1.5 times of the minimum fluidization velocity had no significant effect on the drying rates of rice. The energy consumption for reducing the moisture content of paddy from 0.43 to 0.22 kg/kg dry basis was approximately 7.2 MJ/kg water evaporated. Drying temperature caused the appreciable change of parboiled rice qualities as characterized by water adsorption, whiteness and pasting viscosities, white belly, and hardness. Soaking paddy at a temperature of 70°C for 7–8 h before drying was sufficiently enough for producing parboiled rice, with no white belly. The gelatinization of starch during drying resulted in higher head rice yield of the product as compared to that of raw paddy.     

Assessment of the Actual Performance of an Industrial Solar Kiln for Drying Timber

The aim of this study was to assess the actual performance of an instrumented industrial solar kiln for drying Australian hardwood timber (Eucalyptus pilularis) boards (270 × 43 mm). Ambient temperature and humidity, air temperature and humidity in the kiln, and wood moisture contents were recorded on site (Heron's Creek, NSW, Australia) using sensors and an electronic data acquisition and logging system. The average increases in air temperatures in the kiln compared with ambient conditions were 17.3°C (May-June), 13.8°C (July-August), 10°C (September-October), 8.2°C (November-March), and 7.5°C (March-May) for five runs monitored. Drying times were 2-4 months from initial moisture contents of 43 to 62% (dry-basis) to final moisture contents of 12 to 22%. Overall, the solar kiln has been shown to be an acceptable alternative to air-drying for pre-drying of Australian hardwood timber.     

Quality Attributes of Germinated High-Amylose and Waxy Rice in Superheated Steam and Hot Air Drying

In this work, the effects of amylose content, drying medium, and drying temperature on the fissure, texture, and glycemic index of germinated paddy (GP) were investigated. The amylose content, drying temperature, and drying medium affected the degree of starch gelatinization and percentage of fissure kernels significantly. Hot air drying at 130 and 150°C insignificantly influenced the hardness of Phitsanulok 2 GP with high amylose content after cooking compared to that of shade-dried GP, and the drying temperatures significantly affected the hardness and stickiness of RD6 GP without amylose content. Superheated steam drying caused a significant change in textural properties for both paddy varieties because of complete starch gelatinization. The high-amylose paddy had higher gamma-aminobutyric acid and lower glycemic index than nonamylose paddy. Drying temperature and drying media did not change the gamma-aminobutyric acid and glycemic index of both GP varieties in comparison to their shade-dried samples.