The effect of temperature on the performance and stability of thermophilic anaerobic digestion.

Sustainable operation of an anaerobic sewage sludge digester requires the effective shuttling of carbon from complex organic material to methane gas. The accumulation of intermediates and metabolic products such as volatile fatty acids and hydrogen gas not only reveal inefficiency within the digestion process, but can be detrimental to reactor operation at sufficiently high levels. Eight anaerobic digesters (1 mesophilic and 7 thermophilic) were operated in order to determine the effect of steady-state digestion temperature on the operational stability and performance of the digestion process. Replicate reactors operated at 57.5 degrees C, the highest temperature studied, were prone to accumulation of volatile fatty acids (4052 and 3411 mg/L as acetate) and gaseous hydrogen. Reactors operated at or below 55 degrees C showed no such accumulation of intermediate metabolites. Overall methanogenesis was also greatly reduced at 57.5 degrees C (0.09 L CH4/g VS fed) versus optimal methane formation at 53 degrees C (0.40 L CH4/g VS fed). Microbial community assessment and free energy calculations suggest that the accumulation of fatty acids and hydrogen, and relatively poor methanogenic performance at 57.5 degrees C are likely due to temperature limitations of thermophilic aceticlastic methanogens.     

Methane production and solids destruction in an anaerobic solid waste reactor due to post-reactor caustic and heat treatment.

This study was undertaken to determine the feasibility of caustic and heat treatment of sludge from a dry anaerobic reactor (DAR) with respect to increased methane production and solids destruction. The DAR was operated semi-continuously at 55 degrees C on sized-reduced municipal solid waste at a solids retention time of 15 days. A respirometer was employed to monitor the extent and rate of methane production from anaerobic biodegradation of DAR sludge that was treated with caustic and heat. Results indicate that caustic and heat treatment at 50 degrees C and 175 degrees C increased methane production by 22% and 52%, respectively. Also, volatile solids destruction increased from 46% to 58% and 83%, respectively. Based on these results, economic analysis for a full-scale 10(5) kg/d facility suggests that annual project revenue for 50 degrees C and 175 degrees C treatment is estimated at $21,000 and $445,000, respectively.     

Anaerobic digestion elutriated phased treatment of piggery waste.

The performance of a novel high-rate anaerobic process, the anaerobic digestion elutriated phased treatment (ADEPT) process, for treating a slurry-type piggery waste (55 g COD/L and 37 g TS/L) was investigated. The ADEPT process consists of an acid elutriation slurry reactor for hydrolysis and acidification, followed by an upflow anaerobic sludge bed reactor for methanification. This process provides stable and high system performance with short HRT (7.4 d) and better effluent quality (2 g SCOD/L and 0.68 g VSS/L) due to the alkaline pH condition for hydrolysis/acidification phase, high refractory solids removal and ammonia toxicity reduction. The optimum pH and HRT for hydrolysis/acidogenesis of the piggery waste were 9 and 5 days at both 35 degrees C and 55 degrees C conditions. The hydrolysis and acidification rate in the mesophilic reactor were 0.05 d(-1) and 0.11 d(-1), meaning that hydrolysis was a limiting step. SCOD production by the hydrolysis was about 0.26 g SCOD/g VS(fed) (3.6 g SCOD/g VS reduction). Methane production and content in the system were 0.3 L CH4/g VS(fed) (0.67 L CH4/g VS destroyed) and 80%, respectively, corresponding to 0.23 L CH4/g COD removal (@STP).     

Simultaneous treatment of sewage sludge and food waste by the unified high-rate anaerobic digestion system.

This study aimed to evaluate the performance of the unified high-rate anaerobic digestion (UHAD) system treating co-substrate of sewage sludge and food waste. A 24-hr operating sequence consisted of four steps including fill, react, settle, and draw. The effects of co-substrate and organic loading rate (OLR) on the performance were investigated to verify the system applicability. In each OLR, the UHAD system showed higher CH4 recovery (> 70%), CH4 yield (0.3 L CH4/g VSadded) and CH4 production rate (0.6 L CH4/L/d) than the control system. In the specific methanogenic activity (SMA) tests on thermophilic biomass of the UHAD system, the average SMA of acetate (102 mL CH4/gVSS/d) was much higher than those of butyrate (85 mL CH4/g SS/d) and propionate (42 mL CH4/gVSS/d). It was demonstrated that the UHAD system for co-digestion resulted in higher methane yield and methane production rate due to sequencing batch operation, thermophilic digestion, and co-digestion. The enhanced performance could be attributed to longer retention time of active biomass, faster hydrolysis, higher CH4 conversion rate, and balanced nutrient conditions of co-substrate in the UHAD system. Consequently, this optimized unification could be a viable option for the simultaneous treatment of two types of OFMSW with high stability.     

Upflow anaerobic sludge blanket (UASB) treatment of supernatant of cow manure by thermal pre-treatment.

Upflow anaerobic sludge blanket (UASB) methane fermentation treatment of cow manure that was subjected to screw pressing, thermal treatment and subsequent solid-liquid separation was studied. Conducting batch scale tests at temperatures between 140 and 180 degrees C, the optimal temperature for sludge settling and the color suppression was found to be between 160-170 degrees C. UASB treatment was carried out with a supernatant obtained from the thermal treatment at the optimal conditions (170 degrees C for 30 minutes) and polymer-dosed solid-liquid separation. In the UASB treatment with a COD(Cr) loading of 11.7 kg/m3/d and water temperature of 32.2 degrees C, the COD(Cr) level dropped from 16,360 mg/L in raw water to 3,940 mg/L in treated water (COD(Cr), removal rate of 75.9%), and the methane production rate per COD(Cr) was 0.187 Nm3/kg. Using wastewater thermal-treated at the optimal conditions, also a methane fermentation treatment with a continuously stirred tank reactor (CSTR) was conducted (COD(Cr) in raw water: 38,000 mg/L, hydraulic retention time (HRT): 20 days, 35 degrees C). At the COD(Cr) loading of 1.9 kg/m3/d, the methane production rate per COD(Cr), was 0.153 Nm3/kg. This result shows that UASB treatment using thermal pre-treatment provides a COD(Cr), loading of four times or more and a methane production rate of 1.3 times higher than the CSTR treatment.     

Potential for biohydrogen and methane production from olive pulp.

The present study investigates the potential for thermophilic biohydrogen and methane production from olive pulp, which is the semi-solid residue coming from the two-phase processing of olives. It focussed on: a) production of methane from the raw olive pulp, b) anaerobic bio-production of hydrogen from the olive pulp, and c) subsequent anaerobic treatment of the hydrogen-effluent with the simultaneous production of methane. Both continuous and batch experiments were performed. The hydrogen potential of the olive pulp amounted to 1.6 mmole H2 per g TS. The methane potential of the raw olive pulp and hydrogen-effluent was as high as 19 mmole CH4 per g TS. This suggests that olive pulp is an ideal substrate for methane production and it shows that biohydrogen production can be very efficiently coupled with a subsequent step for methane production.     

Thermophilic anaerobic fermentation of olive pulp for hydrogen and methane production: modelling of the anaerobic digestion process.

The present study investigates the thermophilic biohydrogen and methane production from olive pulp, which is the semi-solid residue coming from the two-phase processing of olives. It focussed on: a) production of methane from the raw olive pulp; b) anaerobic bio-production of hydrogen from the olive pulp; c) subsequent anaerobic treatment of the hydrogen-effluent with the simultaneous production of methane; and d) development of a mathematical model able to describe the anaerobic digestion of the olive pulp and the effluent of hydrogen producing process. Both continuous and batch experiments were performed. The hydrogen potential of the olive pulp amounted to 1.6 mmole H2 per g TS. The methane potential of the raw olive pulp and hydrogen-effluent was as high as 19 mmole CH4 per g TS suggesting that: a) olive pulp is a suitable substrate for methane production; and b) biohydrogen production can be very efficiently coupled with a subsequent step for methane production.     

Organic matter release in low temperature thermal treatment of biological sludge for reduction of excess sludge production.

Thermal treatment applied in association with a biological system allows for a significant reduction in excess sludge production (approximately 50%). In general, heat treatment is described as a sludge disintegration technique. This paper offers a thorough study on the impact of heat treatment, at temperatures below 100 degrees C, on the solubilisation of the sludge COD and its biodegradability. Discontinuous heating experiments were performed on activated and digested sludge. At all temperatures tested the released COD for digested sludge was systematically higher than that for activated sludge (15 and 40%, respectively, at 95 degrees C for 40 min of contact time). For the first 30 min, a 1st order kinetic, with respect to the residual COD, was systematically found. In the range of 40-95 degrees C, digested sludge had a lower activation energy than activated sludge (26 kcal/mol compared to 70-160 kcal/mol). COD solubilisation is thus more positively influenced by temperature in the case of activated sludge. This may be due to the significant difference in the ratio of protein/carbohydrate in digested and activated sludge (1-5 and 0.2-0.7, respectively). The increase in the COD/TKN ratio in the solubilised fraction after thermal treatment of activated sludge suggests a preferential solubilisation of proteins over carbohydrates. Respirometric tests performed on the solubilised COD showed that whatever the sludge origin, only 40-50% of released COD is biodegradable at a conventional hydraulic retention time (i.e., 24 h). Hence, heat treatment would act more through organic matter solubilisation rather than by a biodegradability increase.     

Relative kinetics of anaerobic digestion under thermophilic and mesophilic conditions

With several advantages over the conventional mesophilic anaerobic digestion, such as better sludge quality and higher biogas production, thermophilic anaerobic digestion is regarded as a promising alternative for sludge digestion. Primary and activated sludges are complex materials, and historically, analysis of kinetics has been largely on whole sludge, without analysis of individual components. This paper analyses relative digestion kinetics of pure substrates designed to target main stages of sludge digestion under thermophilic and mesophilic conditions. Hydrolysis rate of cellulose was significantly influenced by temperature with hydrolysis coefficients of--at 55 degrees C (0.7 +/- 0.1 day(-1)), 60 degrees C (0.8 +/- 0.2 day(-1)), 65 degrees C (1.1 +/- 0.2 day(-1)) and 70 degrees C (1.2 +/- 0.2 day(-1)) over 38 degrees C (0.4 +/- 0.1 day(-1)). This strongly follows the Arrhenius relationship, with an activation energy (E(A)) of 31 +/- 4 kJ mol(-1), corresponding to an increase of 1.5x for each 10 degrees C of temperature increase. Glucose uptake was rapid with a wide variety of fermentation products detected under mesophilic conditions, while uptake was slower under thermophilic conditions with acetate and propionate being dominant products. Propionate acetogenesis and acetate-utilizing methanogenesis kinetics were not influenced by temperatures. Hydrolysis is widely regarded as a rate-limiting step in sludge digestion, thus improvements in hydrolysis rates as measured during this study have the potential for significant improvements in overall apparent sludge digestion rates.     

表征水体中生物活性及脱氢酶检测方法研究

为寻求评价发酵产氢活性污泥产氢效能的合理指标,以氯化三苯基四氮唑(TTC)检测法为基础,优化了TTC -比脱氢酶活性检测方法,并分析了发酵产氢活性污泥的TTC -比脱氢酶活性与比产氢速率的相关性.结果表明,发酵产氢活性污泥TTC -比脱氢酶活性的适宜检测方法及条件为:向10mL离心管中依次加入污泥样品1ml (8.47～26.39 g MLVSS·L-1)、17.8mmoL·L-1的TTC溶液1ml、pH8.0的Tris-HCl溶液2.5ml和0.36％的Na2SO3溶液0.5mL,35℃暗处振荡反应20 min;加98％浓硫酸2ml终止反应,以无水乙醇5ml萃取反应产物三苯基甲臜475 nm测定萃取液吸光度.发酵产氢活性污泥的TTC -比脱氢酶活性,与比产氢速率的相关系数R＞0.8,是反映发酵产氢活性污泥产氢活性的一个优良指标.     

Methane conversion efficiency as a simple control parameter for an anaerobic digester at high loading rates

The anaerobic digestion process is globally applied to the treatment of highly concentrated wastes such as industrial and rural effluents, and sewage sludge. However, it is known to be relatively unstable. When loaded with high concentrations of organic material, unwanted volatile fatty acids (VFA) are often produced rather than methane (CH4) gas which can lead to digester acidification and failure. This study investigated digester behaviour under high loading rates, testing the usefulness of stoichiometric methane conversion efficiency as a digester control parameter at high loading rates. Our results show that, in general, the CH4 production rate was proportional to the feed rate (loading rate). However, at very high loading rates, the CH4 production rate was not proportional to the increase in the feeding rate. Consequently, VFA accumulated and the H2 partial pressure increased. The proportionality of the loading rate and gas production rate is stoichiometrically expressed as the conversion efficiency. We found that conversion efficiency was a useful indicator as an early warning of digester imbalance. The digester remained stable at conversion efficiencies above 75%. Dropping below 70% signified the onset of digester failure. As loading rate and methane production data are readily available on-line in most anaerobic digestion plants, the conversion efficiency can be monitored on-line and used as an efficient control technique to maintain safe operation of anaerobic digesters at high loading rates.     

Evaluation of the reject waters from co-digestion of solid wastes from agro-industries in a municipal WWTP.

Overcapacities of anaerobic digesters at municipal WWTPs are frequently used for the treatment of organic wastes in order to increase the biogas production. However, "co-digestion" of organic wastes leads to additional nitrogen loading and to additional loads of non-biodegradable COD. The effects of (co-) digestion of organic wastes from agro-industries (slaughterhouses, dairies and leather industry) on the wastewater cycle have been evaluated in full-scale investigations at Leoben WWTP with a capacity of 90,000 pe where the methane production was increased from 700 to more than 1700 Nm3 CH4 per day. For this evaluation, mass balances for COD and nitrogen have been applied to estimate the fluxes of these substances. Application of this method is described in detail. As the additional loadings, it was found that related to methane production less nitrogen is released from the organic wastes than from the waste sludge. While the ammonia nitrogen load in the effluent from sludge digestion was about 100 g NH4-N per Nm3 of CH4 produced, in the effluent from the digestion of organic wastes only 70 g NH4-N/Nm3 CH4 were found. The decrease in the COD removal efficiency after digestion of the organic wastes started was not regarded as significant enough to be seen as a consequence of the treatment of external substrate.     

Anaerobic bio-hydrogen production using pre-heated river sediments as seed sludge.

Anaerobic bio-hydrogen production is the focus in the field of bio-energy resources. In this paper, a series of batch experiments were conducted to investigate the effects of several factors on anaerobic bio-hydrogen producing process carried out by pre-heated river sediments. The results showed that several factors such as substrate and its concentration, temperature and the initial pH value could affect the anaerobic bio-hydrogen production in different levels. At 35 degrees C and the initial pH of 6.5, using glucose of 20,000 mg COD/L as substrate, the highest hydrogen production of 323.8 ml-H2/g TVS in a 100 ml batch reactor was reached, the specific hydrogen production rate was 37.7 ml-H2/g TVS h, and the hydrogen content was 51.2%. Thereafter using the same pre-heated river sediments as seed sludge, continuous anaerobic bio-hydrogen production was achieved successfully in a lab-scale CSTR with gas-separator. At the organic loading rate of 36 kg COD/m3 d, the highest hydrogen production was 6.3-6.7 l-H2/l-reactor d, the specific hydrogen production was 1.3-1.4 mol-H2/mol-glucose, and the hydrogen content in the gas was 52.3%. The effluent of the bio-reactor contained some small molecular organics, mainly including ethanol, acetate, butyrate and their molar proportion is 1:1:0.6.     

Methane and hydrogen sulfide emissions in UASB reactors treating domestic wastewater

The release of CH(4) and H(2)S in UASB reactors was evaluated with the aim to quantify the emissions from the liquid surfaces (three-phase separator and settler compartment) and also from the reactor's discharge hydraulic structures. The studies were carried out in two pilot- (360 L) and one demo-scale (14 m(3)) UASB reactors treating domestic wastewater. As expected, the release rates were much higher across the gas/liquid interfaces of the three-phase separators (5.4-9.7 kg CH(4) m(-2) d(-1) and 23.0-35.8 g S m(-2) d(-1)) as compared with the quiescent settler surfaces (11.0-17.8 g CH(4) m(-2) d(-1) and 0.21 to 0.37 g S m(-2) d(-1)). The decrease of dissolved methane and dissolved hydrogen sulfide was very large in the discharging hydraulic structures very close to the reactor (>60 and >80%, respectively), largely due to the loss to the atmosphere, indicating that the concentration of these compounds will probably fall to values close to zero in the near downstream structures. The emission factors due to the release of dissolved methane in the discharge structure amounted to around 0.040 g CH(4) g COD(infl)(-1) and 0.060 g CH(4) g COD(rem)(-1), representing around 60% of the methane collected in the three-phase separator.     

Control of C/N ratio for butyric acid production from textile wastewater sludge by anaerobic digestion

Increasing textile wastewaters and their biotreatment byproduct-waste activated sludge are serious pollution problems. Butyric acid production from textile wastewater sludge by anaerobic digestion at different C/N ratios was investigated. Adding starch to textile wastewater sludge with a C/N ratio of 30 increased the butyric acid concentration and percentage accounting for total volatile fatty acids (TVFAs) to 21.42 g/L and 81.5%, respectively, as compared with 21.42 g/L and 10.6% of textile wastewater sludge alone. The maximum butyric acid yield (0.45 g/g VS), conversion rate (0.74 g/g VS(digest)) and production rate (2.25 g/L d) was achieved at a C/N ratio of 30. The biological toxicity of textile wastewater sludge also significantly decreased after the anaerobic digestion. The study indicated that the anaerobic co-digestion of textile wastewater sludge and carbohydrate-rich waste with appropriate C/N ratio is possible for butyric acid production.     

Thermal pre-treatment of primary and secondary sludge at 70 degrees C prior to anaerobic digestion.

In general, mesophilic anaerobic digestion of sewage sludge is more widely used compared to thermophilic digestion, mainly because of the lower energy requirements and higher stability of the process. However, the thermophilic anaerobic digestion process is usually characterised by accelerated biochemical reactions and higher growth rate of microorganisms resulting in an increased methanogenic potential at lower hydraulic retention times. Furthermore, thermal pre-treatment is suitable for the improvement of stabilization and could be realized at relatively low cost especially at low temperatures. The present study investigates the effect of the pre-treatment at 70 degrees C on thermophilic (55 degrees C) anaerobic digestion of primary and secondary sludge in continuously operated digesters. Thermal pre-treatment of primary and secondary sludge at 70 degrees C enhanced the removal of organic matter and the methane production during the subsequent anaerobic digestion step at 55 degrees C. It also greatly contributed to the destruction of pathogens present in primary sludge. Finally it results in enhanced microbial activities of the subsequent anaerobic step suggesting that the same efficiencies in organic matter removal and methane recovery could be obtained at lower HRTs.     

Temperature effects on the trophic stages of perennial rye grass anaerobic digestion

Continuous Stirred Tank Reactors (CSTRs), operated in batch mode, were used to evaluate the feasibility of psychrophilic (low temperature) digestion of perennial rye grass in a long term experiment (150 days) for the first time. The reactors were operated in parallel at 3 different temperatures, 10, 15 and 37 degrees C. Hydrolysis, acidification and methanogenesis were assessed by VS degradation, by soluble chemical oxygen demand (SCOD) and volatile fatty acids (VFA) production, and by methane production, respectively. Hydrolysis was the rate-limiting step at all temperatures and the rates and extent of hydrolysis were considerably lower at 15 and 10 degrees C, than at 37 degrees C. The total VS degradation was 53%, 34% and 19% at 37, 15 and 10 degrees C, respectively. Acidification was not affected by temperature and VFA production and consumption was balanced in all cases, except at 10 degrees C. Methane yields were 0.215 m3 CH4 kg(-1) VS(-1) added, 0.160 m3 CH4 kg(-1) VS(-1) added and 0.125 m3 CH4 kg(-1) VS(-1) added at 37, 15 and 10 degrees C, respectively. Methanogenesis was not strongly affected at 15 C but it became rate-limiting at 10 degrees C. Overall, the solid degradation and methane production performance under psychrophilic conditions was encouraging and greater than previously reported. Considering the non-acclimated, mesophilic nature of the inoculum, there are grounds to believe that low-temperature anaerobic digestion of grass could be feasible if coupled to efficient hydrolysis of the biomass.     

Continuous hydrogen and methane production in a two-stage cheese whey fermentation system

The feasibility of integrating biological hydrogen and methane production in a two-stage process using mixed cultures and cheese whey powder (CWP) as substrate was studied. The effect of operational parameters such as hydraulic retention time (HRT) and organic loading rate (OLR) on the volumetric hydrogen (VHPR) and methane (VMPR) production rates was assessed. The highest VHPR was 28 L H2/L/d, obtained during stable operation in a CSTR at HRT and OLR of 6 h and 142 g lactose/ L/d, respectively. Moreover, hydrogen (13 L/L/d) was produced even at HRT as low as 3.5 h and OLR of 163 g lactose/L/d, nonetheless, the reactor operation was not stable. Regarding methane production in an UASB reactor, the acidified effluent from the hydrogen-producing bioreactor was efficiently treated obtaining COD removals above 90% at OLR and HRT of 20 g COD/L/d and 6 h, respectively. The two-stage process for continuous production of hydrogen and methane recovered over 70% of the energy present in the substrate. This study demonstrated that hydrogen production can be efficiently coupled to methane production in a two-stage system and that CWP is an adequate substrate for energy production.     

Two-phase thermophilic anaerobic digestion process for biohythane production treating biowaste: preliminary results

This paper deals with the optimization of a two-phase anaerobic process treating biowaste for hydrogen and methane production. Neither physical nor chemical pre-treatments were used to optimize the process. The work was carried out at pilot scale, using two CSTRs (200 and 380 L working volume respectively) both maintained at thermophilic temperature (55 C) and fed semi-continuously with biowaste. The experiment was divided into three periods; during the first two periods the organic loading rate was maintained at 20 kg TVS/m3 d and the hydraulic retention time was changed from 6.6 to 3.3 days, while in the last period the digestate of the second reactor was recirculated to the first reactor in order to buffer the system and control pH at levels around 5. The HRT was maintained at 3.3 days and the OLR was decreased at 16.5 kg TVS/m3 d. The best yield was obtained in the last period where a specific hydrogen production of 50.9 L/kg VSfed was reached, with a H2 content in biogas from the first reactor of 36%. The methanogenic stage after the hydrogen conversion reached a specific biogas production of 0.62 m3/kg VSfed and an overall organic removal above 70%, without any stability problem. The overall biogas production was some 1.5 m3 per day with a gas composition of 10% H2 and 50% CH4.