Surface grafting of polymers onto ultrafine silica: Cationic polymerization initiated by oxoaminium perchlorate groups introduced onto ultrafine silica surface

Summary The cationic polymerization initiated by oxoaminium perchlorate groups introduced onto ultrafine silica surface was investigated. The oxoaminium perchlorate groups were successfully introduced by treatment of nitroxyl radicals on silica surface with perchloric acid. The introduction of the nitroxyl radicals was achieved by reaction of 4-hydroxy-2,2,6,6-tetramethyl-piperidinyloxy radical with acid anhydride groups on the surface. The cationic polymerization of isobutyl vinyl ether, N-vinylcarbazole, 2,3-dihydrofuran, and -butyrolactone was initiated by oxoaminium perchlorate groups introduced onto the surface and the corresponding polymers were grafted onto the surface through the propagation of grafted polymer chain from the surface oxoaminium perchlorate groups.     

Surface grafting of polymers onto glass plate: Polymerization of vinyl monomers initiated by initiating groups introduced onto the surface

The surface grafting of polymers onto a glass plate surface was achieved by the polymerization of vinyl monomers initiated by initiating groups introduced onto the surface. Azo groups were introduced onto the glass plate surface by the reaction of 4,4′-azobis(4-cyanopentanoic acid) with isocyanate groups, which were introduced by the treatment with tolylene-2,4-diisocyanate. The radical polymerization of various vinyl monomers was initiated by azo groups introduced onto the glass plate surface and the corresponding polymers were grafted from the surface: The surface grafting of polymers was confirmed by IR spectra, and the contact angle of surface, with water. The contact angle of the glass plate increased by the grafting of hydrophobic polymers, but decreased by the grafting of hydrophilic polymers. The radical postpolymerization was successfully initiated by the pendant peroxycarbonate groups of grafted polymer on the surface to give branched polymer-grafted glass plate. The cationic polymerization of vinyl monomers was also successfully initiated by benzylium perchlorate groups introduced onto the glass plate surface and the corresponding polymers were grafted onto the surface. The contact angle of the glass plate surface obtained from the cationic polymerization of styrene was larger than that obtained from the radical polymerization. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 65: 2165–2172, 1997     

Cationic graft polymerization of polymers from carbon fiber initiated by acylium perchlorate groups introduced onto the surface

The cationic graft polymerization of several monomers initiated by acylium perchlorate groups introduced onto the carbon fiber surface was investigated to modify the surface. The introduction of acylium perchlorate groups was successfully achieved by the reaction of silver perchlorate with acyl chloride groups, which were introduced by the reaction of surface carboxyl groups with thionyl chloride. It was found that the cationic polymerization of styrene is initiated by acylium perchlorate groups on the carbon fiber. In the polymerization, polystyrene was grafted onto the carbon fiber surface through the propagation of polystyrene from the surface. Ungrafted polymer was also formed by the chain transfer reaction of growing polymer cation to the monomer. The acylium perchlorate groups have the ability to initiate cationic ring-opening polymerization of tetrahydrofuran (THF) and ε-caprolactone (CL), polyTHF and polyCL being grafted onto the carbon fiber surface, respectively. Polyacetals, such as poly(1,3-dioxolane) and polyoxymethylene, were able to graft onto the carbon fiber by cationic ring-opening polymerization of the corresponding monomers.     

Surface grafting of polymers onto ultrafine silica: cationic polymerization initiated by benzylium perchlorate groups introduced onto ultrafine silica surface

Summary The cationic graft polymerization initiated by benzylium perchlorate groups introduced onto ultrafine silica surface was investigated. The introduction of benzylium perchlorate groups onto the surface was achieved by the reaction of silver perchlorate with surface benzyl chloride groups, which were introduced by the treatment of silica with 4-(chloromethyl)phenyltrimethoxysilane. The cationic graft polymerization of styrene and cationic ring-opening polymerization of -caprolactone were found to be initiated by the surface benzylium perchlorate groups and the corresponding polymers were grafted onto the surface. The percentage of grafting onto silica surface decreased with increasing polymerization temperature, because chain transfer reaction of growing polymer cation is accelerated with increasing polymerization temperature.     

Surface grafting of polymer onto carbon thin film

The surface grafting of polymers onto carbon thin film deposited on a glass plate was achieved by two methods: the graft polymerization initiated by initiating groups introduced onto the surface; and the trapping of polymer radicals by surface aromatic rings of the thin film. It was found that the radical and cationic graft polymerization of vinyl monomers are initiated by azo and acylium perchlorate groups introduced onto the surface, respectively, and the corresponding polymers are grafted onto the surface: the surface grafting of polymers were confirmed by the contact angle of the surface with water. In addition, the anionic ring-opening alternating copolymerization of epoxides with cyclic acid anhydrides was found to be initiated by potassium carboxylate groups on the carbon thin film to give the corresponding polyester-grafted carbon thin film. On the other hand, polymer radicals formed by the decomposition of azo polymer, such as poly(polydimethylsiloxane-azobiscyanopentanoate) and poly(polyoxyethylene-azobiscyanopentanoate), were successfully trapped by the surface aromatic rings of carbon thin film and polydimethylsiloxane and polyoxyethylene were grafted onto the surface. © 1995 John Wiley & Sons, Inc.     

Cationic Graft Polymerization onto Silica Nanoparticle Surface in a Solvent-Free Dry-System

For the purpose of the prevention of the environmental pollution and the simplification of reaction process, the scale-up synthesis of polymer-grafted silica nanoparticle by surface initiated cationic ring-opening graft polymerization of 2-methyl-2-oxazoline (MeOZO) in a solvent-free dry-system was investigated. The introduction of iodopropyl groups onto the silica surface as initiating group was carried out by the reaction of silanol groups with 3-iodopropyl- trimethoxysilane in a solvent-free dry-system. The graft polymerization of MeOZO onto silica nanoparticle surface in a solvent-free dry-system was initiated by spraying the monomer onto the surface having iodopropyl groups and the polymerization was conducted in powder fluid system under nitrogen. After the polymerization, unreacted MeOZO was readily removed under high vacuum. It was found that the cationic ring-opening polymerization of MeOZO was successfully initiated in the solvent-free dry-system to give polyMeOZO-grafted silica nanoparticles. The maximum grafting of polyMeOZO obtained from the polymerization initiated by iodopropyl groups on the surface reached 47.7 %. The percentage of grafting and grafting efficiency during the cationic ring-opening graft polymerization in the solvent-free dry-system were considerably larger than those in solution system. This suggests that chain transfer reaction from surface growing cation to monomer was effectively inhibited in the solvent-free dry-system.     

Surface grafting of polymers onto aramid powder: graft polymerization of vinyl monomers initiated by azo groups introduced onto the surface of aramid powder

The radical graft polymerization of vinyl monomers onto the surface of aramid powder, i.e., poly(p-phenylene terephthalamide) powder, initiated by azo groups introduced onto the surface was investigated. The introduction of azo groups onto the aramid surface was achieved by the reaction of surface acyl chloride groups, which were introduced by the treatment of aramid powder with adipoyl dichloride, with 2,2′-azobis[2-(2-imidazolyn-2-yl)propane] in the presence of pyridine: the amount of azo groups thus introduced onto the surface was determined to be 0.57 mmol/g by elemental analysis. It was found that the polymerizations of methyl methacrylate (MMA) and styrene were successfully initiated by the azo groups on the surface and that the corresponding polymers were grafted onto the surface. The percentage of surface grafting of polystyrene and poly(methyl methacrylate) (PMMA) increased up to 37.6 and 26.5%, respectively. Thermogravimetric analysis of polymer surface-grafted aramid powder confirmed that the grafting of polymers is limited on the surface. The polymerization rate was found to bear a first-order dependence on the concentration of aramid powder having azo groups. This suggests that in graft polymerization, unimolecular termination preferentially proceeds.     

Graft polymerization of vinyl monomers initiated by peroxycarbonate groups introduced onto silica surface by Michael addition

The introduction of peroxycarbonate groups onto a silica surface and the graft polymerization of vinyl monomers initiated by peroxycarbonate groups introduced onto a silica surface were investigated. The introduction of peroxycarbonate groups onto a silica surface was achieved by Michael addition of amino groups introduced onto the silica surface to t‐butylperoxy‐2‐methacryloyloxyethylcarbonate (HEPO). The amount of peroxycarbonate groups was determined to be 0.17 mmol/g. The graft polymerization of various vinyl monomers such as styrene (St), N‐vinyl‐2‐pyrrolidinone (NVPD), and 2‐hydroxyethyl methacrylate (HEMA) was initiated by peroxycarbonate groups introduced onto the silica surface to give the corresponding polymer‐grafted silicas. The percentage of poly(St)‐grafting reached about 120% after 5 h. This means that 1.20 g of poly(St) is grafted onto 1.0 g of silica. The surface of poly(St)‐grafted silica shows a hydrophobic nature, but the surfaces of poly(NVPD) and poly(HEMA)‐grafted silica show a hydrophilic nature. Furthermore, the poly(St)‐grafted silica was found to give a stable colloidal dispersion in a good solvent for the grafted polymer. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1491–1497, 1999     

Polymerization,grafting and adsorption in the presence of inorganic substrates: Thermal polymerization of styrene with untreated and γ-irradiated silica gel as a case study

The search for innovative and well-defined organic–inorganic hybrid materials demands that the interplay between polymerization reactions, chemical reactivity, and physical adsorption be fully understood. We examine the case study of the thermal polymerization of styrene in the presence of silica, and the effect of pre-irradiation of silica with γ-rays. The effect of adsorption of styrene-derived radical species on the silica support and polymerization conditions on free and grafted (unextractable) polystyrenes and on polymerization mechanism is discussed on the basis of previous literature findings and new data. Evidence is provided of silica derivatization with various species besides polystyrene (¹³C CPMAS NMR), including products from a β-scission of the adsorbed radical intermediates ensuing oxygen donation from the silica network. The polymerization mechanism can be cationic as well as radical, depending on reaction conditions, and the cationic route prevails in the grafting of polystyrene from silica, resulting in a bimodal molecular weight distribution.     

Grafting of branched polymers onto nano-sized silica surface: Postgrafting of polymers with pendant isocyanate groups of polymer chain grafted onto nano-sized silica surface

To control the surface wettability of nano-sized silica surface, the postgrafting of hydrophilic and hydrophobic polymers to grafted polymer chains on the surface was investigated. Polymers having blocked isocyanate groups were successfully grafted onto nano-sized silica surface by the graft copolymerization of methyl methacrylate (MMA) with 2-(O-[1′-methylpropylideneamino]caboxyamino)ethyl methacrylate (MOIB) initiated by azo groups previously introduced onto the surface. The blocked isocyanate groups of poly(MMA-co-MOIB)-grafted silica were stable in a desiccator, but isocyanate groups were readily regenerated by heating at 150 °C. The hydrophilic polymers, such as poly(ethylene glycol) (PEG) and poly(ethyleneimine) (PEI), were postgrafted onto the poly(MMA-co-MOIB)-grafted silica by the reaction of functional groups of PEG and PEI with pendant isocyanate groups of poly(MMA-co-MOI)-grafted silica to give branched polymer-grafted silica. The percentage of grafting increased with increasing molecular weight of PEG, but the number of postgrafted chain decreased, because of steric hindrance. The hydrophobic polymers, such as poly(dimethylsiloxane) were also postgrafted onto poly(MMA-co-MOI)-grafted silica. It was found that the grafting of hydrophobic polymer and the postgrafting of hydrophilic polymer branches readily controls the wettability of silica surface to water.     

Graft polymerization of vinyl acetate onto silica

The free‐radical graft polymerization of vinyl acetate onto nonporous silica particles was studied experimentally. The grafting procedure consisted of surface activation with vinyltrimethoxysilane, followed by free‐radical graft polymerization of vinyl acetate in ethyl acetate with 2,2′‐azobis(2,4‐dimethylpentanenitrile) initiator. Initial monomer concentration was varied from 10 to 40% by volume and the reaction was spanned from 50 to 70°C. The resulting grafted polymer, which was stable over a wide range of pH levels, consisted of polymer chains that are terminally and covalently bonded to the silica substrate. The experimental polymerization rate order, with respect to monomer concentration, ranged from 1.61 to 2.00, consistent with the kinetic order for the high polymerization regime. The corresponding rate order for polymer grafting varied from 1.24 to 1.43. The polymer graft yield increased with both initial monomer concentration and reaction temperature, and the polymer‐grafted surface became more hydrophobic with increasing polymer graft yield. The present study suggests that a denser grafted polymer phase of shorter chains was created upon increasing temperature. On the other hand, both polymer chain length and polymer graft density increased with initial monomer concentration. Atomic force microscopy–determined topology of the polymer‐grafted surface revealed a distribution of surface clusters and surface elevations consistent with the expected broad molecular‐weight distribution for free‐radical polymerization. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 300–310, 2003     

Grafting of vinyl polymers onto VGCF surface and the electric properties of the polymer-grafted VGCF

The graft polymerization of vinyl monomers onto vapor grown carbon fibers (VGCF) initiated by the system consisting of molybdenum hexacarbonyl (Mo(CO)₆) and trichloroacetyl (COCCl₃) groups introduced onto the surface was investigated. The introduction of trichloroacetyl groups onto VGCF surface was successfully achieved by the reaction of carboxyl groups on VGCF surface with trichloroacetyl isocyanate. It was found that the radical graft polymerization of vinyl monomers, such as methyl methacrylate (MMA), styrene, and glycidyl methacrylate (GMA) is successfully initiated by the system consisting of Mo(CO)₆ and COCCl₃ groups introduced onto the surfaces. In the polymerization, the corresponding vinyl polymers were effectively grafted onto the VGCF surface, based on the propagation of polymer from surface radicals formed by the interaction of trichloroacetyl groups and Mo(CO)₆: the percentage of PMMA grafting reached 40%. Polymer-grafted VGCF gave a stable colloidal dispersion in good solvents for grafted polymer. The electric resistance of composite prepared from the polymer-grafted VGCF suddenly increased in organic solvent vapor over 10³ times, and returned to initial resistance when it was transferred into dry air. These results indicate that such composites can be used as novel gas sensors.     

Graft polymerization of vinyl monomers from initiating groups introduced onto polymethylsiloxane-coated titanium dioxide modified with alcoholic hydroxyl groups

The grafting of vinyl polymers onto the surface of polymethylsiloxane-coated titanium dioxide modified with alcoholic hydroxyl groups (Ti/Si–R–OH) were investigated. The introduction of azo and trichloroacetyl groups onto the surface of Ti/Si–R–OH was achieved by the reaction of the surface alcoholic hydroxyl groups with 4,4′-azobis(4-cyanopentanoic acid) and trichloroacetyl isocyanate, respectively. The radical polymerizations of vinyl monomers were successfully initiated by the azo groups introduced onto the surface and by the system consisting of Mo(CO)₆ and Ti/Si–R–COCCl₃. During the polymerization, the corresponding polymers were effectively grafted onto the titanium dioxide surface through propagation from surface radicals formed by the decomposition of azo groups and by the reaction of Mo(CO)₆ with trichloroacetyl groups on the surface. The percentage of grafting and grafting efficiency in the graft polymerization initiated by the system consisting of Ti/Si–R–COCCl₃ and Mo(CO)₆ were much larger than those initiated by azo groups. The polymer-grafted titanium dioxide was found to produce a stable colloidal dispersion in good solvents for the grafted polymer. The dispersibility of poly(N,N-diethylacrylamide)-grafted titanium dioxide in water was controlled by temperature. In addition, the wettability of the surface of titanium dioxide to water was readily controlled by grafting of hydrophilic or hydrophobic polymers.     

Modification of Silica Nanoparticles with Miktoarm Polymer Brushes via ATRP

Silica nanoparticles were successfully modified with miktoarm brushes via atom transfer radical polymerization (ATRP) using three different approaches. In the first approach: “graft onto and from”, a poly(tert-butyl acrylate) (PtBA) macroinitiator was grafted onto the surface of a monomer-modified silica nanoparticle. Then, polystyrene (PSt) brush was grafted from the surface-tethered reactive chain end. In the second approach: “two-step reverse ATRP”, the PtBA and poly(n-butyl acrylate) (PBA) brushes were consecutively grafted from initiator-modified silica particles via ATRP. The polymerization was initiated from the silica surface via a two-step controlled thermal decomposition of surface-tethered diazo initiator moieties. In the third method: “diblock first”, a diblock copolymer of poly(tert-butyl acrylate) and poly(glycidyl methacrylate) (PtBA-b-PGMA) was grafted onto amine-modified silica particles. The diblock copolymer was covalently attached to the silica surface via interaction between surface-tethered amine groups and the short reactive block containing glycidyl groups. Next, the polystyrene brushes were grafted from surface-tethered reactive chain end. The materials prepared by three different approaches were characterized using gel permeation chromatography (GPC) and thermogravimetric analysis (TGA). The PtBA brushes were hydrolyzed under acidic conditions to form poly(acrylic acid) (PAA) brushes. The resulting materials were imaged using atomic force microscopy (AFM) and transmission electron microscopy (TEM).     

Preparation and characterization of end-alkoxysilylated polystrene and the grafting behaviors onto inorganic pigments. I. Utilization of 4-isopropoxydimethylsilyl-α-methylstyrene

Novel end-functional polystyrene having isopropoxydimethylsilyl (IPS) groups at the end part of the chain was prepared. IPS groups were introduced by the reaction between the living polystyryl anion and 4-isopropoxydimethylsilyl-α-methylstyrene ( 1 ) in THF at 195 K. The resultant polymer was characterized by GPC, ¹H-NMR, and TLC. It was confirmed that the polymer had several units of 1 at the chain end and a fairly narrow molecular weight distribution. IPS groups in the polymer can be hydrolyzed with strong acid such as mono-n-butylphosphate (MBP) but not with weak acid and base. Grafting behaviors of the polymer onto silica and alumina were studied in toluene in the presence of MBP as a catalyst. The polymer was grafted onto silica effectively. However, it cannot be grafted onto alumina because of predominant adsorption of MBP onto alumina having a basic surface. © 1995 John Wiley & Sons, Inc.     

Towards controlled cationic polymer growth from inorganic oxide defects: Directing the mechanism of polystyrene grafting from γ-irradiated silica

Most studies on surface-initiated controlled polymerizations for the synthesis of polymeric covalent organic-inorganic hybrid materials focus on chemical methods requiring specific modifications of the inorganic substrate. Few mechanistically-aware approaches have been undertaken towards exploiting the reactivity of defects induced by physical techniques such as ionizing radiations or UV–Vis light. Within this framework, we take grafted polymerization of styrene from γ-irradiated silica as a mechanistic testing ground where para- and diamagnetic silica defects are present, and polymerization proceeds through both radical and cationic mechanisms, resulting in a bimodal molecular weight distribution. We show that these mechanistic intricacies can be sorted out by resorting to the chemical arsenal developed in the last decades for controlled polymerizations. Specifically, we obtained a silica-polystyrene grafted material by cationic grafting from at 30 °C, a unimodal molecular weight distribution, and a relatively high molecular weight (Mn = 7.4 kDa) with a PDI of 1.68.     

Grafting polymers onto carbon black surface by trapping polymer radicals

Polystyrene, poly(styrene-co-maleic anhydride), poly[styrene-co-(4-vinylpyridine)] and poly(4-vinylpyridine) with well-defined molecular weights and polydispersities were synthesized using 4-hydroxyl-2,2,6,6-tetramethylpiperidin-1-oxyl (HTEMPO)-mediated radical polymerization initiated by azobisisobutyronitrile or benzoyl peroxide. The resultant polymers were grafted onto carbon black surface through a radical trapping reaction at 130 °C in DMF. ¹H NMR, TGA, TEM, AFM, DSC and dynamic light scattering were used to characterize the carbon black grafted with polymers. It was found that the carbon black grafted with polystyrene and poly(styrene-co-maleic anhydride) could be dispersed in THF, chloroform, dichloromethane, DMF, etc., and the carbon black grafted with poly(4-vinylpyridine) and poly[styrene-co-(4-vinylpyridine)] could be well dispersed in ethanol.     

Radical polymerization of vinyl monomers in the presence of carbon black initiated by 2,2'‐azobisisobutyronitrile and benzoyl peroxide in ionic liquid

The radical polymerization behavior of vinyl monomers, such as styrene, methyl methacrylate (MMA), and vinyl acetate (VAc), in the presence of carbon black initiated by benzoyl peroxide (BPO) and 2,2'‐azobisisobutyronitrile (AIBN) in ionic liquid (IL) was compared with those in toluene. 1‐Butyl‐3‐methylimidazolium hexafluorophosphate was used as IL. The radical polymerization of vinyl monomers initiated by BPO and AIBN in the presence of carbon black was remarkably retarded in toluene. On the contrary, the retardation of the polymerization by carbon black was considerably reduced in IL. During the radical polymerization in the presence of carbon black, a part of polymer formed was grafted onto carbon black surface based on the termination reaction of the growing polymer radicals with carbon black surface. The percentage of grafting and molecular weight of polymer in IL were much higher than those in toluene. This may be due to the fact that lifetime of the growing polymer radical is prolonged because of high viscosity of IL. Therefore, the growing polymer radicals with higher molecular weight were trapped by carbon black surface, because of stabilization of polymer radicals. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Grafting polystyrene onto silica nanoparticles via RAFT polymerization

Reversible addition-fragmentation chain transfer (RAFT) polymerization was used to graft polystyrene (PS) onto silica nanoparticles. A novel route was used to prepare the RAFT agent, 2-butyric acid dithiobenzoate (BDB) by substitution of dithiobenzoate magnesium bromide with sodium 2-bromobutyrate under alkali condition in aqueous solution. Epoxy groups were covalently attached to silica nanoparticles by condensation reaction of 3-glycidyloxypropyltrimethoxysilane (GPS) with the hydroxyl on the silica particle surface. RAFT agent functionalized nanoparticles were produced by ring-open reaction of the epoxy group with the carboxyl group of BDB. Then, PS chains with controlled molecular weights and narrow polydispersities (less than 1.1) were grown from the RAFT agent anchored nanoparticle surface. FT-IR, transmission electron microscopy (TEM) and thermogravimetric analysis (TGA) results showed that PS chains grew from silica particles by surface RAFT polymerization.     

聚苯乙烯/纳米SiO_2复合材料的制备

经硅烷偶联剂KH-570改性后的纳米SiO2表面具有大量可反应性基团-CH=CH2。以苯乙烯和改性后的纳米SiO2为原料,利用自由基聚合反应,制备得到聚苯乙烯/纳米SiO2复合材料。FT IR和TG证明聚苯乙烯大分子链已成功接枝到纳米SiO2粒子表面。由于扩散作用的影响,相对于偶氮二异丁腈引发聚合反应,热聚合反应具有更高的接枝率。