Co-Precipitation Synthesis and Spectral Characteristics of Long Afterglow Phosphor Y2O2 S： Sm^3＋, Mg^2＋ , Ti^4＋

Y2O2S：Sm^3＋, Mg^2＋, Ti^4＋ phosphor was synthesized by co-precipitation method. The crystalline structure of all synthesized phosphors was investigated by XRD. The result showed that all synthesized phosphors had a hexagonal crystal structure, which was the same as Y2O2S. The emission spectrum and excitation spectrum were measured, and the effect of Sm^3 ＋ molar ratio on the spectra was discussed. The emission spectra of the phosphors showed three emission peaks due to typical transitions of Sm^3 ＋ （4G5/2→6HJ ,J = 5/2, 7/2, 9/2）, and the emission peaks at 606 nm was stronger than others. With the increase of Sm^3 ＋ molar ratio, the emission intensity was strengthened. The excitation peaks were ascribed to the representative energy transition 4f→4f of Ti^4＋ phosphor prepared by co-precipitation method was Sm^3＋ ions. The results indicated that the Y2O2S ： Sm^3＋ , Mg^2＋ , an efficient long afterglow phosphor.     

Synthesis of Long Afterglow Phosphor CaAl2Si2O8 ：Eu^2＋, Dy^3＋ via Sol-Gel Technique and Its Optical Properties

The long afterglow phosphor CaAl2Si2O8：Eu^2＋ , Dy^3＋ was prepared by a sol-gel method. The sol-gel process and the structure of the phosphor were investigated by means of X-ray diffraction analysis （XRD）. It is found that the single anorthite phase formed at about 1000 %, which is 300 % lower than that required for the conventional solid state reaction. The obtained phosphor powders are easier to grind than those of solid state method and the partical size of phosphor has a relative narrow distribution of 200 to 500 nm. The photoluminescence and afterglow properties of the phosphor were also characterized. An obvious blue shift occurs in the excitation and emission spectra of phosphors obtained by sol-gel and solid state reaction methods. The change of the fluorescence spectra can be attributed to the sharp decrease of the crystalline grain size of the phosphor resulted from the sol-gel technique.     

Structure and luminescent properties of luminous polypropylene fiber based on Sr2MgSi2OT：EU^2＋,Dy^3＋

The luminous polypropylene fiber based on long afterglow luminescent material Sr2MgSi2O7：Eu^2＋,Dy^3＋was prepared by melt-spinning process. Micro-morphology, phase composition, crystal structure, spectral features and afterglow properties of the lu-minescent fiber were tested and analyzed. The results indicated that the fiber had independent superposition phase features of both Sr2MgSi2O7：Eu2＋,Dy3＋and polypropylene. The range of its excitation wavelength was located between 250-450 nm;therefore, the luminescent fiber could be excited by ultraviolet or visible light. It could emit blue light of 460 nm wavelength after excitation, which was caused by the 5d-4f transition of Eu^2＋ions within the host lattice. The initial luminescent intensity was more than 0.8 cd/m^2, and afterglow life lasted 7 h. The afterglow decay was composed of rapid-decaying and slow-decaying processes, and the decay charac-teristics depended on the depth and concentration of trap level in the Sr2MgSi2O7：Eu^2＋,Dy^3＋.     

Synthesis of Long Afterglow Photoluminescent Materials Sr2MgSi2O7：Eu^2＋,Dy^3＋ by Sol-Gel Method

Long afterglow photoluminescent materials Sr2MgSi2O7 dopeo With Eu^2 ,Dy^3 were prepared by sol-gel method. The synthesized samples were characterized by X-ray diffraction. The excitation spectrum, emission spectrum and long decay curve were measured and analyzed. XRD pattern indicates that phosphor is with Sr2MgSi2O7 crystal structure. The wide range of excitation wavelength indicates that luminescent material can be excited by light from ultraviolet ray to visible light. The main peak of emission spectrum is located at 466nm. Sample excited by visible light can emit bright blue light, and the afterglow time lasts more than 8h.     

Preparation and photoluminescence of Tb^3＋ doped SrAl2O4 phosphor by composite combustion method

High-efficient Tb^3＋ activated SrAl2O4 phosphor was synthesized by a combined combustion-solid-state reaction method. The precursor of SrAl2O4：Th^3＋ phosphor was prepared via a combustion process, and then the as-prepared powder was heated in a reductive ambient of activated carbon at 1250 ℃ for 1 h. The results of X-ray diffraction, scanning electron microscopy, and photoluminescence spectra revealed the influence of the dosage of urea and heated process on the crystallinity, morphology, and photoluminescence of the phosphor. Comparing with traditional solid-sate reaction, the crystallinity and emission intensity of the SrAl2O4：Tb^3＋ phosphor were improved by this two-step process.     

Synthesis of Long Afterglow Phosphors MAI204：Eu^2＋ , Dy^3＋ （M=Ca, Sr, Ba） by Microemulsion Method and Their Luminescent Properties

Long afterglow phosphors MAl2O4：Eu^2＋ , Dy^3＋ （M = Ca, Sr, Ba） were synthesized by microemulsion method, and their crystal structure and luminescent properties were compared and investigated. XRD patterns of samples indicate that phosphors CaAl2O4：Eu^2＋, Dy^3＋ and SrAl2O4 ： Eu^2＋, Dy^3＋ are with monoelinie crystal structure and phosphor BaAl2O4：Eu^2＋ , Dy^3＋ is with hexagonal crystal structure. The wide range of excitation spectrum of phosphors MAl2O4： Eu^2 ＋ , Dy^3＋ （M = Ca,Sr, Ba） indicates that the luminescent materials can he excited by light from ultraviolet ray to visible light and the maximum emission wavelength of phosphors MAl2O4：Eu^2＋ , Dy^3＋ （M = Ca, Sr, Ba） is found mainly at λem of 440 nm （M = Ca）, 520 nm （M = Sr） and 496 nm （M = Ba） respectively, the corresponding colors of emission light are blue, green and eyna-green respectively. The afterglow decay tendency of phosphors can he summarized as three processes： initial rapid decay, intermediate transitional decay and very long slow decay. Afterglow decay curves coincide with formula I = At^ - n, and the sequence of afterglow intensity and time is Sr 〉 Ca 〉 Ba.     

Optical Spectroscopy of Er^3＋ and Er^3＋/Yb^3＋ Co-doped Bi2O3-GeO2-B2O3-ZnO Glasses

The （60 - x）Bi2O3 - xGeO2-30B2O3-10ZnO （x = 5, 10, 20, 30 molar percent） glasses doped with Er^3＋ and Er^3＋/Yb^3＋ were fabricated using the melting method. The thermal stability of the glasses was studied with their DTA curves. The results show that the difference between the glass transition temperature and the crystallization onset temperature increases with the increase of GeO2 content, indicating that the thermal stability of the glass has become better. The absorption spectra were recorded and the stimulated emission cross sections were calculated using the McCumber theory. The Ω2, O4, and Ω6 parameters,the transition probability, the radiative lifetime, and the fluorescence branch ratio of Er^3＋ for optical transition were calculated from their absorption spectra in terms of reduced matrix U^（t）（λ = 2, 4, 6） character for optical transitions. The infrared emission of Er^3＋ was measured upon excitation with 970 nm light and the full width at half-maximum （FWHM） was estimated from the emission spectra. The pumping efficiency and the intensity of the emission at the 1.54 μm band of Er^3＋ were enhanced considerably by co-doping Yb^3＋ .     

Effect of mixing process on the luminescent properties of SrAl_2O_4:Eu~(2+),Dy~(3+) long afterglow phosphors

A new mixing method was developed for solid-state reaction synthesis of SrAl2O4:Eu2+,Dy3+ long afterglow phosphors.The morphology and crystal structure of the phosphors were analyzed with scanning electron microscope(SEM) and X-ray diffractometer(XRD).The excitation and emission spectra of the long afterglow phosphors were measured,and the main emission band was around 514 nm.The decay time of the product was measured and compared with the phosphors prepared using dry-mixing method and wet-mixing method.It ...     

Researches on preparation and properties of polypropylene nonwovens containing rare earth luminous materials

Polypropylene composite nonwovens containing rare-earth strontium aluminates Sr Al2O4：Eu2＋,Dy3＋ and functional additives were fabricated by the spun-bonded technique.The optical properties, morphology and mechanical properties of the samples were characterized.Results from scanning electron microscopy photographs（SEM） indicated that the surface of the fiber was destroyed by the addition of rare earth luminescent materials lightly but the thickness of the fiber was uniform.Differential scanning calorimetry results showed that pure polypropylene has the double crystallization peak at 162.3 and 165.1 °C.Studies from X-ray diffraction showed that the nonwoven prepared with the luminescent materials contained the α-monoclinic crystal and β crystalline phase.Furthermore, the afterglow properties were tested, which showed that the afterglow curve of the luminous nonwoven was similar to that of strontium aluminate, and the intensity was more intensive than luminous nonwoven at the beginning.The nonwoven fabricated with the luminescent material did not affect the crystal lattice of the polymer making the materials have potential applications in fluorescent lamps and field emission displays（FEDs）.     

Synthesis of Long Afterglow SrAl2O4 :Eu2+, Dy3+ Phosphor by Microemulsion Method

Long afterglow SrAl2 O4: Eu2 , Dy3 phosphor was synthesized by microemulsion method. The synthesized phosphor was characterized by XRD. XRD pattern indicates that the phosphor has monoclinic SrAl2 O4 crystal structre.The microstructure of the phosphor was investigated by SEM and TEM. The excitation spectrum, emission spectrum and afterglow decay curve were measured, the wide range of excitation wavelength indicated that the luminescent material could be excited by the light from ultraviolet ray to visible light, and the emission maximum was found to peak mainly at λem of 525 nm. The sample excited by ultraviolet visible light could emit bright green light.     

SrAl2O4∶Eu2+,Dy3+磷光粉低成本制备工艺及发光性能研究

以工业铝酸钠溶液制备的氢氧化铝为铝基原料,采用高温固相反应法合成了SrAl2O4∶Eu2+,Dy3+磷光粉,考察了稀土掺杂量、烧结温度及硼酸加入量对其发光性能、激发光谱及发射光谱的影响,并通过XRD谱及余辉衰减曲线对最佳工艺条件下制备的样品进行表征。结果表明,当稀土掺杂量x(Eu)=3%、x(Dy)=3%,烧结温度为1 300℃,烧结时间为4h,硼酸加入量w(H3BO3)=9%时,所制备磷光粉样品仍保持SrAl2O4的晶体结构,其发光性能最好,发光强度最大,主激发波长在360nm左右,主发射波长在510nm左右;余辉为黄绿色,衰减时间长。     

Preparation and Luminescence of SrAi2O4:Eu2+, Dy3+ Nano-Particle

SrAl2O4: Eu2 , Dy3 nano-particle luminescence material was prepared by sol-gel method. Influences of synthesis conditions on the particle size and luminescence properties of SrAl2O4: Eu2 , Dy3 were studied. The synthesis process and the properties of the samples were analyzed by DTA, TGA, XRD, SEM. The result suggested that the formation of SrAl2O4: Eu2 , Dy3 sol is a slow heat release process beginning at 500 ℃ and peaking at 759 ℃.SrAl2O4: Eu2 ,Dy3 crystalline was formed at 1100 ℃. The luminescence properties of the SrAl2O4: Eu2 , Dy3 nanoparticle were compared with the conventional SrAl2O4: Eu2 , Dy3 particles. The average particle size of the product is about 30 nm. The excitation spectrum of the sample shows a broad band with peaks at 240, 330, 378 and 425 nm. The emission spectrum is a broadband spectrum with a peak at 523 nm.     

Investigations into thermoluminescence and afterglow characterization of strontium aluminates with boron-modification and reductions via sol-gel route

The effects of strontium aluminates of SrAl2O4:Eu2+,Dy3+(SAED) and boron-modified SAED (BSAED) phases synthesized from a sol-gel process on thermoluminescence (TL) along with their afterglow properties were systematically investigated with thermal activation in the different atmospheres. The result showed that the addition of boron and the reduction routes of Eu3+to Eu2+ in SrAl2O4:Dy3+were related to phosphorescent decay properties. The aid of Dy3+to induce the hole-trapping effect required both SAED and BSAED to be heated at 1300°C under the H2/N2(5%:95%) atmosphere. However, the trapping behavior of the reductions of SAED in nitrogen was similar to the compound without Dy3+co-doping SrAl2O4:Eu2+ (SAE) in H2/N2(5%:95%). BSAED showed deeper traps in situ compared to SAED which contained no boron, and this led to the better afterglow properties of BSAED than those of SAED. The afterglow spectrum of BSAED showed two peaks at 400±1 nm and 485±1 nm, which were two individuals composed and contributed from different depths of traps at 0.57 and 0.76eV, accordingly. The depth of the traps was calculated from the Hoogenstraaten’s plot of glow curves. The calculations for SAED and SAE were at around 0.43 and 0.18eV, respectively.     

SrAl2O4:Eu, Dy Nanometer Phosphors Synthesized by Combustion Method

SrAl2 O4: Eu, Dy nanometer phosphors were synthesized by combustion method at 500 ～ 900℃, followed by heating the combustion sample at 1150℃ at a weak reductive atmosphere and nanometer phosphor with much better luminescent properties was obtained. The influences of the initiating combustion temperature, H3BO3 quantity, the mass ratio of urea and nitrate on the luminescent intensity of nanometer phosphors were studied. The optimum synthetic conditions were determined. The analysis results by transmission electron microscopy (TEM) indicate that the particle size of the synthetic product is less than 75 nm. The luminescent materials do not need to be ground. Their coating can be refined. It supplies a new approach to the rapid preparation of the luminescent materials at low temperature. The excitation and emission spectra indicate that the main peaks in the excitation and emission spectrum of nanometer phosphor synthesized by combustion method shifted to the short wavelength compared with the phosphor obtained by the solidstate reaction synthesis method. The reason of blue shift was explained. The afterglow decay results indicate that the decay speed of the afterglow for nanometer phosphor is faster than that obtained by the solid-state reaction method.     

Mg~（2＋）,Ca~（2＋）,Ba~（2＋）离子部分取代对SrAl_2O_4：Eu~（2＋）,Dy~（3＋）晶体结构和发光性能的影响

采用高温固相反应法制备了Sr0.9M0.1Al2O4：Eu2＋,Dy3＋（M=Mg,Ca,Ba）长余辉发光材料,并对其晶体结构、光谱性质、余辉特性进行了分析.X射线衍射测试结果表明,Mg2＋,Ca2＋,Ba2＋离子部分取代SrAl2O4基质中的Sr后,基质晶体结构并没有发生改变.光谱测试结果表明,Mg2＋,Ca2＋,Ba2＋取代后发光材料的激发光谱都是一个从250~450 nm范围内的宽激发带,在266nm,320nm,360nm,416 nm处各有一个激发峰.发射光谱中Mg2＋和Ba2＋的取代使波长出现蓝移,而Ca2＋的取代使波长出现红移.余辉测试结果表明,Ca2＋取代后的余辉时间长于Mg2＋和Ba2＋的取代.     

SrAl2O4 :Eu2+, Dy3+ Long Afterglow Phosphors Prepared by Chemical Coprecipitation Method

SrAl2 O4: Eu2 , Dy3 long afterglow phosphors were prepared by chemical coprecipitation method. Ammonium carbonate and ammonium hydrogen carbonate were used as the precipitants. The preparation of the SrAl2 O4: Eu2 ,Dy3 precursor was completed at room temperature by controlling the concentration of the metal-salt solution, pH value of the system, etc. The phosphors were prepared by sintering the precursor at 1000 ～ 1200 ℃ in a weak reducing atmosphere for 2 h. The XRD, SEM, excitation spectra, emission spectra and afterglow decay of the samples were tested and the optimal synthesis conditions of the SrAl2O4: Eu2 , Dy3 long afterglow phosphors prepared by precipitation method were determined. The phosphor which had good luminescent properties is prepared and its persistent time can reach more than 1600 min. In the coprecipitation process, a small amount of glucose operates to refe the luminescent powders. The particle size of the phosphor can be less than 1 μm. The sintering temperature of the sample prepared by the coprecipitation method is much lower than that of the one prepared by the high temperature solid state method.Compared with the high temperature solid state method, a clear blue shift occurs in the excitation and emission spectra of the samples.     

Effect of Organic Solvent and Resin on Luminescent Capability of SrAl2O4:Eu2+, Dy3+ Phosphor

Organic substance such as solvent and resin's effect on luminescent capability of SrAl2O4:Eu2 , Dy3 phosphor was studied. Some organic solvents and resins were selected for experimentation. The results indicate that those organic solvents will not have negative effect on the applied capability of SrAl2O4:Eu2 , Dy3 phosphor. Adopting the organic resins and covering method, the afterglow luminance of SrAl2O4:Eu2 , Dy3 phosphor was increased by 85.01% and 82.51%.