Effect of molar ratio of TiO2/SiO2 on the properties of particles synthesized by flame spray pyrolysis

Titania (TiO₂)–silica (SiO₂) nanoparticles were synthesized from sprayed droplets of a mixture of TEOS and TTIP by flame spray pyrolysis (FSP). The effect of molar ratio between TEOS and TTIP in the mixture on the particle properties such as particle morphology, average particle diameter, specific surface area, crystal structure, etc., were determined using TEM, XRD, BET, and FT-IR. A UV-spectrometer was also used to measure the absorption spectrum and the band gap energy of the product particles. As the molar ratio of TEOS/TTIP increased by increasing TEOS concentration at the fixed TTIP concentration, the average particle diameter of the mixed oxide nanoparticles increased with maintaining uniform dispersion between TiO₂ and SiO₂, and crystal structure was transformed from anatase to amorphous. The band gap energy of the TiO₂–SiO₂ nanoparticles increased with respect to the increase of the molar ratio due to the decrease of width of UV-absorption spectrum. Photocatalytic activity of TiO₂–SiO₂ composite particles decreased with the concentration of TEOS.     

Investigation of surface modification of rutile TiO2 nanoparticles with SiO2/Al2O3 on the properties of polyacrylic composite coating

Surface modification and characterization of TiO₂ nanoparticles as an additive in a polyacrylic clear coating were investigated. For the improvement of nanoparticles dispersion and the decreasing of photocatalytic activity, the surface of nanoparticles was modified with binary SiO₂/Al₂O₃. The surface treatment of TiO₂ nanoparticles was characterized with FTIR. Microstructural analysis was done by AFM. The size, particle size distribution and zeta potential of TiO₂ nanoparticles in water dispersion was measured by DLS method. For the evaluation of particle size and the stability of nanoparticles in water dispersions with higher solid content the electroacoustic spectroscopy was made. To determine the applicability and evaluate the transmittance of the nano-TiO₂ composite coatings UV–VIS spectroscopy in the wavelength range of 200–800 nm was employed. The results showed that surface treatment of TiO₂ nanoparticles with SiO₂/Al₂O₃ improves nanoparticles dispersion and UV protection of the clear polyacrylic composite coating.     

Photocatalytic activity of water-based acrylic coatings containing fluorosilane treated TiO2 nanoparticles

In this study, TiO₂ nanoparticles were treated with 1H,1H,2H,2H-perfluorooctyltriethoxysilane (fluorosilane) in an alkaline condition. The treated nanoparticles were added to a water-base acrylic coating to introduce photocatalytic activity. Dispersion of the nanoparticles and also Ti element wt% on the coatings’ surface were evaluated using atomic force microscopy and energy dispersive X-ray analyses, respectively. Photocatalytic activity of the coatings was investigated via study of the decomposition – under UVA irradiation – of Rhodamine B, as a pollutant model deposited on the coatings’ surface. Durability of the coatings in short-term was investigated using atomic force microscopy and scanning electron microscopy observations.     

Investigating the role of surface treated titanium dioxide nanoparticles on self-cleaning behavior of an acrylic facade coating

In this study, the addition of silane treated TiO₂ nanoparticles on the self-cleaning properties of an acrylic facade coating was evaluated. Tetraethoxyorthosilicate, TEOS, was used for surface treatment of TiO₂ nanoparticles. The silica grafting on the TiO₂ nanoparticles was characterized via Fourier Transform Infrared spectroscopy, specific surface area measurement, pore size distribution, and real density measurements. The effect of surface treatment and content of nanoparticles on the photocatalytic activity of acrylic coating and self-cleaning properties was studied. For this purpose, the photodegradation of Rhodamine B (Rh.B) dyestuff, as a colorant model, was investigated by colorimetric technique, while the coating samples were exposed to UVA irradiation. Performance of the acrylic coating films was evaluated by gloss change during accelerated weathering conditions. Also, the surface morphology of the coating films was studied using SEM analysis. The results showed that the addition of both treated and untreated TiO₂ nanoparticles provides self-cleaning property to the acrylic coatings. However, silica surface treatment of TiO₂ nanoparticles reduces the coating degradation caused by TiO₂. This is more evident when higher concentrations of the treated TiO₂ nanoparticles are used.     

Weathering performance of spruce coated with water based acrylic paint modified with TiO2 and clay nanoparticles

This work examines the effect of wood specimens coated with water based acrylic coatings modified with TiO₂ and clay nanoparticles against weathering strain. The long-term durability of the specimens towards climate strain was studied within a relatively short time frame by accelerated climate ageing. The surface changes that occurred as a result of photodegradation of the specimens subjected to accelerated climate exposures were studied using colour measurements and Fourier transform infrared (FTIR) spectroscopy. The results revealed a significant decrease in the intensity of lignin bands attributed to degradation of the lignin component of the wood. However, the intensity of the lignin photodegradation was lower for coated specimens, with slightly lower degradation for the specimens coated with paints modified with TiO₂ and unmodified montmorillonite clay nanoparticles.     

Combined TiO2/SiO2 mesoporous photocatalysts with location and phase controllable TiO2 nanoparticles

Combined TiO₂/SiO₂ mesoporous materials were prepared by deposition of TiO₂ nanoparticles synthesised via the acid-catalysed sol–gel method. In the first synthesis step a titania solution is prepared, by dissolving titaniumtetraisopropoxide in nitric acid. The influences of the initial titaniumtetraisopropoxide concentration and the temperature of dissolving on the final structural properties were investigated. In the second step of the synthesis, the titania nanoparticles were deposited on a silica support. Here, the influence of the temperature during deposition was studied. The depositions were carried out on two different mesoporous silica supports, SBA-15 and MCF, leading to substantial differences in the catalytic and structural properties. The samples were analysed with N₂-sorption, X-ray diffraction (XRD), electron probe microanalysis (EPMA) and transmission electron microscopy (TEM) to obtain structural information, determining the amount of titania, the crystal phase and the location of the titania particles on the mesoporous material (inside or outside the mesoporous channels). The structural differences of the support strongly determine the location of the nanoparticles and the subsequent photocatalytic activity towards the degradation of rhodamine 6G in aqueous solution under UV irradiation.     

PPV/TiO2 hybrid composites prepared from PPV precursor reaction in aqueous media and their application in solar cells

In this work, poly(phenylene vinylene) (PPV) and TiO₂ nanocomposites containing different amounts of TiO₂ were prepared through PPV precursor reaction in aqueous media. The TiO₂ components were introduced into the systems by two methods, i.e. through in situ sol-gel reaction or by mixing commercially available TiO₂ nanoparticles with the PPV precursor before reaction. The composite prepared by mixing commercially available TiO₂ nanoparticles shows perfect crystal character of the anatase TiO₂, but TiO₂ particles severely agglomerate in the PPV matrix. The composite prepared by introducing TiO₂ nanoparticles through the sol-gel reaction shows uniform nanoscale dispersion of anatase TiO₂ in PPV matrix. The UV-vis and FL spectroscopic analyses confirm the formation of the TiO₂/PPV composites and reveal the enhanced PL quenching effect as the TiO₂ content increases. The PPV/TiO₂ composites can show significant photovoltaic response. Better photovoltaic performance is observed for the solar cells prepared by using the in situ sol-gel reaction method.     

Synthesis of TiO2/PAA nanocomposite by RAFT polymerization

Due to the strong tendency of nanoparticles such as metal oxides to agglomerate, homogeneous dispersion of these materials in a polymeric matrix is extremely challenging. In order to overcome this problem and to enhance the filler-polymer interaction, this study focused on living polymerization that was initialized from the surface of titania nanofillers. A new method for synthesizing TiO₂/polymer nanocomposites was found with a good dispersion of the nanofillers by using the bifunctional RAFT agent, 2-{[(butylsulfanyl)carbonothioyl]sulfanyl}propanoic acid). This RAFT agent has an available carboxyl group to anchor onto TiO₂ nanoparticles, and an SC(SC₄H₉) moiety for subsequent RAFT polymerization of acrylic acid (AA) to form n-TiO₂/PAA nanocomposites. The functionalization of n-TiO₂ was determined by FTIR and partitioning studies, the livingness of the polymerization was verified using GPC and NMR, while the dispersion of the inorganic filler in the polymer was studied using electron microscopy, FTIR and thermal analysis.     

Effects of TiO2 and clay nanoparticles loading on weathering performance of coated wood

The weathering performance of Norway spruce coated with acrylic water based paint mixed with TiO₂ and clay nanoparticles were investigated. Uncoated specimens and specimens coated with unmodified paint were used as references. This work describes the effect of the nanoparticles in general and compares the performance of 1 wt% and 3 wt% of nanoparticles in particular on the weathering performance of the coated specimens. Accelerated ageing experiments were performed in an Atlas solar simulator to evaluate the ageing behaviour of the coated wood and characterized through colour measurements and Fourier transform infrared (FTIR) spectroscopy before, during and at the end of the exposure periods. In general, the addition of TiO₂ and clay nanoparticles slightly slowed down the coated specimens degradation compared to specimens coated with unmodified paint.     

TiO2, TiO2/Ag and TiO2/Au photocatalysts prepared by spray pyrolysis

TiO₂, TiO₂/Ag and TiO₂/Au photocatalysts exhibiting a hollow spherical morphology were prepared by spray pyrolysis of aqueous solutions of titanium citrate complex and titanium oxalate precursors in one-step. Effects of precursor concentration and spray pyrolysis temperature were investigated. By subsequent heat treatment, photocatalysts with phase compositions from 10 to 100% rutile and crystallite sizes from 12 to 120 nm were obtained. A correlation between precursor concentration and size of the hollow spherical agglomerates obtained during spray pyrolysis was established. The anatase to rutile transformation was enhanced with metal incorporations and increased precursor concentration. The photocatalytic activity was evaluated by oxidation of methylene blue under UV-irradiation. As-prepared TiO₂ particles with large amounts of amorphous phase and organic residuals showed similar photocatalytic activity as the commercial Degussa P25. The metal incorporated samples showed comparable photocatalytic activity to the pure TiO₂ photocatalysts.     

Synthesis and Photocatalytic Activity of Anatase TiO2 Nanoparticles-coated Carbon Nanotubes

A simple and straightforward approach to prepare TiO₂-coated carbon nanotubes (CNTs) is presented. Anatase TiO₂ nanoparticles (NPs) with the average size ~8 nm were coated on CNTs from peroxo titanic acid (PTA) precursor even at low temperature of 100 °C. We demonstrate the effects of CNTs/TiO₂ molar ratio on the adsorption capability and photocatalytic efficiency under UV–visible irradiation. The samples showed not only good optical absorption in visible range, but also great adsorption capacity for methyl orange (MO) dye molecules. These properties facilitated the great enhancement of photocatalytic activity of TiO₂ NPs-coated CNTs photocatalysts. The TiO₂ NPs-coated CNTs exhibited 2.45 times higher photocatalytic activity for MO degradation than that of pure TiO₂.     

The dependence of the photocatalytic activity of TiO2/carbon nanotubes nanocomposites on the modification of the carbon nanotubes

Nanostructural TiO₂/modified multi-wall carbon nanotubes photocatalysts were prepared by hydrolysis of Ti(iso-OC₃H₇)₄ providing chemical bonding of anatase TiO₂ nanoparticles onto oxidized- or amino-functionalized multi-wall carbon nanotubes (MWCNT). The processes of functionalization of the MWCNT and the deposition of TiO₂ influence the photocatalytic activity of the synthesized nanocomposites. The phase composition, crystallite size, and the structural and surface properties of the obtained TiO₂/modified-MWCNT nanocomposite were analyzed from XRD, FEG-SEM, TEM/HRTEM and FTIR data, as well low temperature N₂ adsorption. In the photocatalytic study, the TiO₂/oxidized-MWCNT catalyst showed the highest and the TiO₂/amino functionalized-MWCNT catalysts somewhat lower degradation rates, indicating that the enhancement of photocatalysis was supported by the more effective electron transfer properties of the oxygen- than amino-containing functional groups, which support the efficient charge transportation and separation of the photogenerated electron-hole pairs.     

Visible photocatalytic activity and photoelectrochemical behavior of TiO2 nanoparticles modified with metal porphyrins containing hydroxyl group

TiO₂ nanoparticles modified with 5-(p-hydroxylphenyl)-10,15,20-triphenylporphyrin (HTPP), 5-(p-hydroxylphenyl)-10,15,20-triphenylporphyrin zinc (ZnHTPP) and trans-dichloro-5-(p-hydroxylphenyl)-10,15,20-triphenylporphyrin tin (SnHTPP) were prepared in order to improve the visible photocatalytic activity of TiO₂ nanoparticles. The photocatalytic activity of the modified TiO₂ nanoparticles was investigated by carrying out the photodegradation of methyl orange in aqueous solution under visible light irradiation. The TiO₂ nanoparticles modified with SnHTPP show the highest visible photocatalytic activity with a degradation ratio of 86% of methyl orange after 180 min irradiation among three catalysts. This result indicates that the central metal ions in porphyrins can significantly influence the sensitization efficiency of porphyrins. In addition, the photoelectrochemical behavior of the modified TiO₂ nanoparticles was examined and related to their photocatalytic activity. Finally, the photocatalytic mechanism was discussed preliminarily.     

Structural colors from TiO2/SiO2 multilayer flakes prepared by sol-gel process

Preparation of TiO₂/SiO₂ multilayer flakes and their application to decorative powders were investigated. In contrast to conventional products prepared through the multicoating of core platelets, the coreless TiO₂/SiO₂ multilayer flakes were prepared by detaching multilayer films from their substrates. These flakes exhibited structural colors, when the optical path length of both the TiO₂ and SiO₂ layers are adjusted to be one fourth of the wavelength of visible light. A multicoating of more than five layers resulted in the propagation of cracks, which prevented the preparation of thick flakes. Paint films fabricated using the multilayer flakes and acrylic resins showed reflectance spectra that were comparable with those obtained for multicoatings on substrates.     

Operando FTIR study of the photocatalytic oxidation of acetone in air over TiO2–ZrO2 thin films

Operando FTIR spectroscopy has been used to study the photocatalytic oxidation of acetone vapors over semiconductors films containing TiO₂ and ZrO₂. Preparation of these coatings was carried out by dipping a silicon wafer in stable sols containing particles of TiO₂, Ti_1−xZr_xO₂, or a mixture of ZrO₂ and TiO₂. These differences in chemical composition and phase homogeneity were selected in order to determine their effect on the photocatalytic performance. A transmission cell specifically designed for in situ studies of photocatalytic coatings was utilized for the FTIR experiments under reaction conditions. In contrast with investigations with powdered photocatalysts, the use of thin films guarantees that the whole semiconductor is irradiated, and for that reason purely photochemical reactions are monitored. Acetone adsorption takes place molecularly and is higher on the Ti_1−xZr_xO₂ coating. This fact is very likely related to the higher specific surface of the samples containing Zr. However, the maximum photocatalytic rate for acetone degradation corresponds to the films composed by a binary mixture of TiO₂ and ZrO₂. On the other hand, remarkable differences on the type and concentration of intermediates appearing as a result of the photocatalytic oxidation of acetone are found for the coatings studied. A simple kinetic model was applied to analyze the evolution of both gas phase and surface species. The parameters obtained indicate that each specific surface process is affected in a different way by the variation in the composition of the photoactive films.     

SnO2 nanoparticle embedded TiO2 nanofibers — Highly efficient photocatalyst for the degradation of rhodamine B

SnO₂ nanoparticle embedded TiO₂ nanofibers were fabricated by a simple electrospinning method. The relationship between the SnO₂/TiO₂ weight ratio and photocatalytic efficiency was investigated from the view point of Rhodamine B decomposition. In addition, electron microscopic analysis, energy dispersive analysis, X-ray diffraction analysis, and photoluminescence study demonstrated that SnO₂ nanoparticle was successfully embedded in TiO₂ nanofibers. TiO₂ nanofibers containing SnO₂ nanoparticle provided an enhanced interfacial region between TiO₂ and SnO₂. SnO₂ nanoparticles embedded TiO₂ nanofibers exhibited highly efficient photocatalytic activity under UV light irradiation due to high charge separation of electron–hole pairs.     

Preparation and photocatalysis of TiO2-fluoropolymer electrospun fiber nanocomposites

The preparation and photocatalytic properties of titanium dioxide (TiO₂)-fluoropolymer fiber nanocomposites were studied. The fluoropolymer nanofibers with carboxyl group were prepared by electrospinning. The complex was formed between carboxyl on fluoropolymer electrospun fiber surface and titanium ion, and then the TiO₂ nanoparticles were immobilized on the surface of fluoropolymer electrospun fibers through hydrothermal complex-precipitation. By controlling the reaction conditions, different sizes and numbers of TiO₂ nanocrystals can be obtained. The Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) results reveal that an interaction exists between TiO₂ and fluoropolymer fibers. The degradation of methylene blue solution is performed by TiO₂-fluoropolymer fiber nanocomposites under UV irradiation. There may be an adsorption-migration-photodegradation process during the degradation of methylene blue by using TiO₂-fluoropolymer fiber nanocomposites as photocatalyst. The experimental results show that the TiO₂-fluoropolymer fiber nanocomposites have good photocatalytic ability, recycling and stability for the potential applicability in an environmental remediation.     

Preparation of multi-walled carbon nanotube supported TiO2 and its photocatalytic activity in the reduction of CO2 with H2O

Multi-walled carbon nanotube (MWCNT) supported TiO₂ composite catalysts were prepared by sol-gel and hydrothermal methods. X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy and N₂-adsorption analysis were carried out to characterize the composite catalysts. In using the sol-gel method, the MWCNTs were coated with anatase TiO₂ nanoparticles, and by the hydrothermal method, rutile TiO₂ nanorods were uniformly deposited on the MWCNTs. The photocatalytic activities of the composite catalysts were evaluated by the reduction of CO₂ with H₂O. The results indicate that the addition of an appropriate amount of MWCNTs as supports for TiO₂ could remarkably improve the efficiency of the photocatalytic reaction. The composite catalysts prepared by the sol-gel method lead to the main formation of C₂H₅OH, while HCOOH is found to be the major product on the sample prepared by the hydrothermal method.     

Synthesis of a TiO2 ceramic membrane containing SrCo0.8Fe0.2O3 by the sol-gel method with a wet impregnation process for O2 and N2 permeation

A SrCo_0.8Fe_0.2O₃ impregnated TiO₂ membrane (TiO₂-SrCo_0.8Fe_0.2O₃ membrane) was successfully prepared using a sol-gel method in combination with a wet impregnation process. The membrane was subjected to a single gas permeance test using oxygen (O₂) and nitrogen (N₂). The TiO₂ membrane was immersed in the SrCo_0.8Fe_0.2O₃ solution, dried and then calcined to affix SrCo_0.8Fe_0.2O₃ into the membrane. The effect of the acid/alkoxide (H⁺/Ti⁴⁺) molar ratio of the TiO₂ sol on the TiO₂ phase transformation was investigated. The optimal molar ratio was found to be 0.5, which resulted in nanoparticles with a mean size of 5.30 nm after calcination at 400 °C. The effect of calcination temperature on the phase transformation of TiO₂ and SrCo_0.8Fe_0.2O₃ was investigated by varying the calcination temperature from 300 to 500 °C. X-ray diffraction spectroscopy (XRD) and Fourier transform infrared (FTIR) analysis confirmed that a calcination temperature of 400 °C was preferable for preparing a TiO₂-SrCo_0.8Fe_0.2O₃ membrane with fully crystallized anatase and SrCo_0.8Fe_0.2O₃ phases. The results also showed that polyvinyl alcohol (PVA) and hydroxypropyl cellulose (HPC) were completely removed. Field emission scanning electron microscopy (FESEM) analysis results showed that a crack-free and relatively dense TiO₂ membrane (∼0.75 μm thickness) was created with a multiple dip-coating process and calcination at 400 °C. The gas permeation results show that the TiO₂ and TiO₂-SrCo_0.8Fe_0.2O₃ membranes exhibited high permeances. The TiO₂-SrCo_0.8Fe_0.2O₃ membrane developed provided greater O₂/N₂ selectivity compared to the TiO₂ membrane alone.     

Preparation of TiO2/carbon nanotubes photocatalysts: The influence of the method of oxidation of the carbon nanotubes on the photocatalytic activity of the nanocomposites

A method for the preparation of efficient TiO₂/multi-wall carbon nanotubes nanocomposite photocatalysts by precipitation of anatase TiO₂ nanoparticles onto differently oxidized carbon nanotubes is presented. The precursor compound titanium(IV) bromide was hydrolyzed producing pure anatase phase TiO₂ nanoparticles decorated on the surface of the oxidized carbon nanotubes. The oxidative treatment of the carbon nanotubes influenced the type, quantity and distribution of oxygen-containing functional groups, which had a significant influence on the electron transfer properties, i.e., the photocatalytic activity of the synthesized nanocomposites. The results of C.I. Reactive Orange 16 photodegradation in the presence of all the synthesized nanocomposites showed their better photocatalytic activity in comparison to the commercial photocatalyst Degussa P-25.