高速率8PSK信号的载波同步及实现

提出一种高速率8PSK信号的载波同步方案,数字锁相环组合频偏搜索实现接收机小频偏的载波同步;多组小频偏同步单元的并行操作获得接收机大频偏的粗略估计,基于反馈闭环实现载波粗同步,然后由一组小频偏同步单元完成残余频偏的精确跟踪及相位同步.分析了载波同步的抖动特性,并基于FPGA实现了该方案.测试结果表明,该载波同步方案动态范围大,跟踪性能好,相位抖动小,长期稳定性好,在中低信噪比下,系统实现损耗小于0.5dB.适合于中继卫星信道高速率8PSK信号的载波同步.     

一种通用MPSK载波同步方法及其FPGA实现

为解决MPSK体制信号解调中可能存在的较大载波频偏,介绍一种结合基于最大似然准则的FFT频偏估计与通用载波锁相环的多调制体制通用载波同步方案。依次分析了该方案的算法原理、结构特点与运算和硬件复杂度,并说明该算法在FPGA上实现该方案的整体结构安排与关键技术要点。在Xilinx的XC4VLX200芯片上实现了该电路。结果表明该电路可完成对较大的频偏、较低的信噪比条件下MPSK信号载波同步工作,具有较好的工程应用价值。     

一种全数字化载波频偏估计器算法

本文提出一种适合ＱＡＭ调制信号的全数字经载波频偏观测器算法,它用于不再采用锁相环同步器的全数字接收机中直接测量频偏的大小,文中提出了频偏观测器算法,接着引入频偏的卡尔曼滤波算法,最终把频偏观测器与卡尔曼滤波器相结合构成了频偏估计器,为存在较大偏的移动通信信道中解决载波同步问题提供了一种实现方案。     

高阶QAM信号多状态自适应卡尔曼滤波载波同步算法

通信信号盲载波恢复是非协作模式下接收方解调的关键环节之一。为提高频偏捕获范围与速度,同时有效增强算法跟踪时变频偏能力,本文针对正交幅度调制(QAM)信号,通过理论推导得出滤波器环路带宽的变化特性,提出一种基于自适应判决引导扩展卡尔曼滤波的载波同步算法。该算法在现有卡尔曼滤波载波同步算法的基础上,引入多状态自适应切换机制自适应地改变滤波器参数,并依据实验测试数据分析得出调整原则并完成滤波器参数的选取。理论分析和仿真表明,与已有的卡尔曼载波同步算法及二阶数字锁相环算法相比,该算法不仅捕获速度更快范围更大,且能在存在时变多普勒频移的情况下较好地跟踪时变频偏和相位,在大频偏条件下的算法跟踪性能与鲁棒性等方面均有优势。      

一种扩展载波环频率捕获范围的方法

在MPSK数字载波恢复中,可以通过锁频锁相环捕获大范围频率偏移。低信噪比下,锁相环的频率捕获范围较小,而工程中锁频环剩余频偏通常较大,因而需要扩展锁相环的频率捕获范围。描述了频差估计以及COSTAS环中相位检测技术的实现方法,分析了COSTAS环的相位检测特性,并根据这种算法的鉴相特性提出了一种扩展频率捕获范围的载波恢复方法。以QPSK为例,通过MATLAB仿真了这种技术在低信噪比情况下对频率偏移的检测与跟踪性能,仿真结果表明,提出的方法适合低信噪比下大范围的频率捕获。     

大频偏低信噪比条件下QPSK载波环的设计

在介绍锁相环原理的基础上,针对大频偏和低信噪比条件对锁相环参数进行修正,并分析了传统判决反馈环载波跟踪方法的缺点。提出一种在大频偏和低信噪比条件下FFT频偏估计辅助锁相环的设计方法。仿真结果表明该环路在极低信噪比下仍可以快速捕获。将该方法应用于工程中,并与单锁相环载波同步系统的锁定时间进行比较,实测结果证明了分析的正确性。     

一种改进的高动态QPSK信号解调算法

正交相移键控(QPSK)调制解调方式广泛应用于深空通信、数字卫星通信等高速系统中,高动态QPSK信号具有较大的多普勒载波频偏,针对现有的解调算法对QPSK信号频偏估计范围小、精度较低等问题,提出了一种改进的高动态QPSK信号解调算法。该算法利用基于Zoom-FFT的Quinn频率估计算法对载波频偏进行估计,将频偏估计分为粗估计和精估计两个过程,对估计所得频偏进行补偿后利用Costas环完成载波同步。在MATLAB中对算法进行了仿真,仿真结果表明,该算法能够实现对高动态大频偏QPSK信号的有效捕获,与传统的解调方式相比,该算法对载波频偏的估计范围更大,且具有更高的频偏估计精度和更好的误码性能。     

TDMA信号的宽范围载波同步译码联合迭代处理

针对时分多址(Time Division Multiple Access,TDMA)信号提出了宽范围的载波同步译码联合迭代处理的方案。该方案主要分为三个部分,首先利用TDMA信号的同步码进行数据辅助同步,对信号中的大频偏和相偏进行粗估计和纠正;然后利用线性调频Z变换(Chirp-Z Transform,CZT)算法针对整突发帧进行非数据辅助同步,精确估计和纠正信号的剩余频偏;最后通过利用译码器输出的软信息进行编码辅助同步,多次迭代得到剩余相偏的精确估计,最终实现载波的精确同步并输出译码结果。实验结果表明,所提方案具有同步捕获范围宽、参数估计精度高、译码输出误比特率低等优点,在低信噪比环境下也能表现出优良性能。     

一种QPSK信号数字解调大频偏载波恢复算法

在全数字QPSK解调器中,有时存在着相当大的相对载波频偏,导致接收机不能正常工作.针对QPSK信号相干解调中载波同步问题,提出一种采用FFT及锁相环联合提取大频偏信号载波的方法,达到了对大频偏进行有效估计并提取较纯载波的目的.该方法统计性能好,结构简单,可估计的载波频率适应范围大,算法适合数字电路实现.     

卫星信道下低速扩频信号的快速同步

提出一种适合于卫星信道下低速扩频信号的快速同步方案。在高速时钟的驱动下,利用抽头数远小于扩频码长的匹配滤波器实现扩频信号的快速捕获;扩频码同步后先利用部分相关值对大载波频差进行初步估计,估计范围可接近符号率;然后再利用全相关值对剩余小频差进行精确的估计;最后利用锁相环实现载波的跟踪。计算结果和仿真结果表明,该方案是切实可行的。     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.     

New insert layer structure OLEDs

An insert layer structure organic electroluminescent device（OLED） based on a new luminescent material （Zn（salen）） is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn（salen）/Liq/LiF/A1/CuPc/NPD/Zn（salen）/Liq/LiF/A1. Effective insert electrode layers comprising LiF（1nm）/Al（5 nm） are used as a single semitransparent mirror, and bilayer cathode LiF（1 nm）/A1（100 nm） is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.