Tri-reforming of methane: a novel concept for catalytic production of industrially useful synthesis gas with desired H2/CO ratios

A novel process concept called tri-reforming of methane has been proposed in our laboratory using CO₂ in the flue gases from fossil fuel-based power plants without CO₂ separation [C. Song, Chemical Innovation 31 (2001) 21–26]. The proposed tri-reforming process is a synergetic combination of CO₂ reforming, steam reforming, and partial oxidation of methane in a single reactor for effective production of industrially useful synthesis gas (syngas). Both experimental testing and computational analysis show that tri-reforming can not only produce synthesis gas (CO + H₂) with desired H₂/CO ratios (1.5–2.0), but also could eliminate carbon formation which is usually a serious problem in the CO₂ reforming of methane. These two advantages have been demonstrated by tri-reforming of CH₄ in a fixed-bed flow reactor at 850 °C with supported nickel catalysts. Over 95% CH₄ conversion and about 80% CO₂ conversion can be achieved in tri-reforming over Ni catalysts supported on an oxide substrate. The type and nature of catalysts have a significant impact on CO₂ conversion in the presence of H₂O and O₂ in tri-reforming in the temperature range of 700–850 °C. Among all the catalysts tested for tri-reforming, their ability to enhance the conversion of CO₂ follows the order of Ni/MgO > Ni/MgO/CeZrO > Ni/CeO₂ ≈ Ni/ZrO₂ ≈ Ni/Al₂O₃ > Ni/CeZrO. The higher CO₂ conversion over Ni/MgO and Ni/MgO/CeZrO in tri-reforming may be related to the interaction of CO₂ with MgO and more interface between Ni and MgO resulting from the formation of NiO/MgO solid solution. Results of catalytic performance tests over Ni/MgO/CeZrO catalysts at 850 °C and 1 atm with different feed compositions confirm the predicted equilibrium conversions based on the thermodynamic analysis for tri-reforming of methane. Kinetics of tri-reforming were also examined. The reaction orders with respect to partial pressures of CO₂ and H₂O are different over Ni/MgO, Ni/MgO/CeZrO, and Ni/Al₂O₃ catalysts for tri-reforming.     

La2NiO4 tubular membrane reactor for conversion of methane to syngas

La₂NiO₄ tubular membranes of relative density over 92% were used to separate oxygen from air and facilitate the partial oxidation of methane to H₂ and CO at 900 °C. When methane was fed into a tube of inner surface area 5.11 cm² at a rate of 10.5 ml/min, methane throughput conversion was 89%, CO selectivity 96%, H₂/CO ratio 1.5, and the equivalent oxygen flux was 6.8 ml/min. The surface of the La₂NiO₄ membrane exposed to CH₄ decomposed into La₂O₃ and Ni, while the surface in contact with air remained almost unchanged. It is suggested that the conversion of methane in the membrane reactor involves the reforming of methane by the H₂O and CO₂ catalyzed by nickel.     

Role of CeO2 in Ni/CeO2–Al2O3 catalysts for carbon dioxide reforming of methane

Ni catalysts supported on γ-Al₂O₃, CeO₂ and CeO₂–Al₂O₃ systems were tested for catalytic CO₂ reforming of methane into synthesis gas. Ni/CeO₂–Al₂O₃ catalysts showed much better catalytic performance than either CeO₂- or γ-Al₂O₃-supported Ni catalysts. CeO₂ as a support for Ni catalysts produced a strong metal–support interaction (SMSI), which reduced the catalytic activity and carbon deposition. However, CeO₂ had positive effect on catalytic activity, stability, and carbon suppression when used as a promoter in Ni/γ-Al₂O₃ catalysts for this reaction. A weight loading of 1–5 wt% CeO₂ was found to be the optimum. Ni catalysts with CeO₂ promoters reduced the chemical interaction between nickel and support, resulting in an increase in reducibility and stronger dispersion of nickel. The stability and less coking on CeO₂-promoted catalysts are attributed to the oxidative properties of CeO₂.     

The role of lanthana loading on the catalytic properties of Pd/Al2O3-La2O3 in the NO reduction with H2

The role of La₂O₃ loading in Pd/Al₂O₃-La₂O₃ prepared by sol–gel on the catalytic properties in the NO reduction with H₂ was studied. The catalysts were characterized by N₂ physisorption, temperature-programmed reduction, differential thermal analysis, temperature-programmed oxidation and temperature-programmed desorption of NO.

The physicochemical properties of Pd catalysts as well as the catalytic activity and selectivity are modified by La₂O₃ inclusion. The selectivity depends on the NO/H₂ molar ratio (GHSV = 72,000 h⁻¹) and the extent of interaction between Pd and La₂O₃. At NO/H₂ = 0.5, the catalysts show high N₂ selectivity (60–75%) at temperatures lower than 250 °C. For NO/H₂ = 1, the N₂ selectivity is almost 100% mainly for high temperatures, and even in the presence of 10% H₂O vapor. The high N₂ selectivity indicates a high capability of the catalysts to dissociate NO upon adsorption. This property is attributed to the creation of new adsorption sites through the formation of a surface PdO_x phase interacting with La₂O₃. The formation of this phase is favored by the spreading of PdO promoted by La₂O₃. DTA shows that the phase transformation takes place at temperatures of 280–350 °C, while TPO indicates that this phase transformation is related to the oxidation process of PdO: in the case of Pd/Al₂O₃ the O₂ uptake is consistent with the oxidation of PdO to PdO₂, and when La₂O₃ is present the O₂ uptake exceeds that amount (1.5 times). La₂O₃ in Pd catalysts promotes also the oxidation of Pd and dissociative adsorption of NO mainly at low temperatures (<250 °C) favoring the formation of N₂.     

Characterization and activity in dry reforming of methane on NiMg/Al and Ni/MgO catalysts

Dry reforming of methane has been investigated on two series of catalysts either prepared by co-precipitation: n(Ni_xMg_y)/Al, Ni_xMg_y and Ni_xAl_y or prepared by impregnation: Ni/MgO (mol% Ni = 5, 10). The catalysts, calcined at 600–900 °C, were characterized by different techniques: BET, H₂-TPR, TPO, XRD, IR, and TEM-EDX analysis. The surface BET (30–182 m² g⁻¹) decreased with increasing the temperature of calcination, after reduction and in the presence of Mg element. The XRD analysis showed, for n(Ni_xMg_y)/Al catalysts, the presence of NiAl₂O₄ and NiO–MgO solid solutions. The catalyst reducibility decreased with increasing the temperature of pretreatment. The n(Ni_xMg_y)/Al catalysts were active for dry reforming of methane with a good resistance to coke formation. The bimetallic catalyst Ni_0.05Mg_0.95 (calcined at 750 °C and tested at 800 °C) presents a poor activity. In contrast, the 5% Ni/MgO catalyst, having the same composition but prepared by impregnation, presents a high activity for the same calcination and reaction conditions. For all the catalysts the activity decreased with increasing the temperature of calcination and a previous H₂-reduction of the catalyst improves the performances. The TPO profiles and TEM-EDX analysis showed mainly four types of coke: CH_x species, surface carbon, nickel carbide and carbon nanotubes.     

Catalytic combustion of methane over bimetallic Pd–Pt catalysts: The influence of support materials

The effect of support material on the catalytic performance for methane combustion has been studied for bimetallic palladium–platinum catalysts and compared with a monometallic palladium catalyst on alumina. The catalytic activities of the various catalysts were measured in a tubular reactor, in which both the activity and stability of methane conversion were monitored. In addition, all catalysts were analysed by temperature-programmed oxidation and in situ XRD operating at high temperatures in order to study the oxidation/reduction properties.

The activity of the monometallic palladium catalyst decreases under steady-state conditions, even at a temperature as low as 470 °C. In situ XRD results showed that no decomposition of bulk PdO into metallic palladium occurred at temperatures below 800 °C. Hence, the reason for the drop in activity is probably not connected to the bulk PdO decomposition.

All Pd–Pt catalysts, independently of the support, have considerably more stable methane conversion than the monometallic palladium catalyst. However, dissimilarities in activity and ability to reoxidise PdO were observed for the various support materials. Pd–Pt supported on Al₂O₃ was the most active catalyst in the low-temperature region, Pd–Pt supported on ceria-stabilised ZrO₂ was the most active between 620 and 800 °C, whereas Pd–Pt supported on LaMnAl₁₁O₁₉ was superior for temperatures above 800 °C. The ability to reoxidise metallic Pd into PdO was observed to vary between the supports. The alumina sample showed a very slow reoxidation, whereas ceria-stabilised ZrO₂ was clearly faster.     

Catalytic conversion of methane and CO2 to synthesis gas over a La2O3-modified SiO2 supported Ni catalyst in fluidized-bed reactor

In this contribution, a commercial spherical SiO₂ was modified with different amounts of La₂O₃, and used as the support of Ni catalysts for autothermal reforming of methane in a fluidized-bed reactor. Nitrogen adsorption, XRD and H₂-TPR analysis indicated that La₂O₃-modified SiO₂ had higher surface area, strengthened interaction between Ni and support, and improved dispersion of Ni. CO₂-TPD found that La₂O₃ increased the alkalescence of SiO₂ and improved the activation of CO₂. Coking reaction (via both temperature-programmed surface reaction of CH₄ (CH₄-TPSR) and pulse decomposition of CH₄) disclosed that La₂O₃ reduced the dehydrogenation ability of Ni. CO₂-TPO, O₂-TPO (followed after CH₄-TPSR) confirmed that only part amount of carbon species derived from methane decomposition could be removed by CO₂, and O₂ in feed played a crucial role for the gasification of the inactive surface carbons. Ni/xLa₂O₃-SiO₂ (x = 10, 15, 30) possessed high activity and excellent stability for autothermal reforming of methane in a fluidized-bed reactor.     

Coprecipitated iron-containing catalysts (Fe-Al2O3, Fe-Co-Al2O3, Fe-Ni-Al2O3) for methane decomposition at moderate temperatures: Part II. Evolution of the catalysts in reaction

Coprecipitated Fe-Al₂O₃, Fe-Co-Al₂O₃ and Fe-Ni-Al₂O₃ catalysts is shown to be very efficient in carbon deposition during methane decomposition at moderate temperatures (600–650 °C). The carbon capacity of the most efficient bimetallic catalysts containing 50–65 wt.% Fe, 5–10 wt.% Co (or Ni) and 25–40 wt.% Al₂O₃ is found to reach 145 g/g_cat. Most likely, their high efficiency is due to specific crystal structures of the metal particles and formation of optimum particle size distribution. According to the TEM data, catalytic filamentous carbon (CFC) is formed on them as multiwall carbon nanotubes (MWNTs). The phase composition of the catalysts during methane decomposition is studied using a complex of physicochemical methods (XRD, REDD, Mössbauer spectroscopy and EXAFS). Possible mechanisms of the catalyst deactivation are discussed.     

CO2 reforming of CH4 over nanocrystalline zirconia-supported nickel catalysts

Mesoporous nanocrystalline zirconia with high-surface area and pure tetragonal crystalline phase has been prepared by the surfactant-assisted route, using Pluronic P123 block copolymer surfactant. The synthesized zirconia showed a surface area of 174 m² g⁻¹ after calcination at 700 °C for 4 h. The prepared zirconia was employed as a support for nickel catalysts in dry reforming reaction. It was found that these catalysts possessed a mesoporous structure and even high-surface area. The activity results indicated that the nickel catalyst showed stable activity for syngas production with a decrease of about 4% in methane conversion after 50 h of reaction. Addition of promoters (CeO₂, La₂O₃ and K₂O) to the catalyst improved both the activity and stability of the nickel catalyst, without any decrease in methane conversion after 50 h of reaction.     

Simultaneous production of hydrogen and carbon nanostructures by decomposition of propane and cyclohexane over alumina supported binary catalysts

Nano-scale, binary, 4.5 wt.% Fe–0.5 wt.% M (M = Pd, Mo or Ni) catalysts supported on alumina have been shown to be very effective for the decomposition of lower alkanes to produce hydrogen and carbon nanofibers or nanotubes. After pre-reduction at 700 °C, all three binary catalysts exhibited significantly lower propane decomposition temperatures and longer time-on-stream performances than either the non-metallic alumina support or 5 wt.% Fe/Al₂O₃. Catalytic decomposition of propane using all three catalysts yielded only hydrogen, methane, unreacted propane, and carbon nanotubes. Above 475 °C, hydrogen and methane were the only gaseous products. Catalytic decomposition of cyclohexane using the (4.5 wt.% Fe–0.5 wt.% Pd)/Al₂O₃ catalyst produced primarily hydrogen, benzene, and unreacted cyclohexane below 450 °C, but only hydrogen, methane, and carbon nanotubes above 500 °C. The carbon nanotubes exhibited two distinct forms depending on the reaction temperature. Above 600 °C, they were predominantly in form of multi-walled nanotubes with parallel walls in the form of concentric graphene sheets. At or below 500 °C, carbon nanofibers with capped and truncated stacked-cone structure were produced. At 625 °C, decomposition of cyclohexane produced a mixture of the two types of carbon nanostructures.     

Decomposition of nitric oxide over perovskite oxide catalysts: effect of CO2, H2O and CH4

Direct nitric oxide decomposition over perovskites is fairly slow and complex, its mechanism changing dramatically with temperature. Previous kinetic study for three representative compositions (La_0.87Sr_0.13Mn_0.2Ni_0.8O_3−δ, La_0.66Sr_0.34Ni_0.3Co_0.7O_3−δ and La_0.8Sr_0.2Cu_0.15Fe_0.85O_3−δ) has shown that depending on the temperature range, the inhibition effect of oxygen either increases or decreases with temperature. This paper deals with the effect of CO₂, H₂O and CH₄ on the nitric oxide decomposition over the same perovskites studied at a steady-state in a plug-flow reactor with 1 g catalyst and total flowrates of 50 or 100 ml/min of 2 or 5% NO. The effect of carbon dioxide (0.5–10%) was evaluated between 873 and 923 K, whereas that of H₂O vapor (1.6 or 2.5%) from 723 to 923 K. Both CO₂ and H₂O inhibit the NO decomposition, but inhibition by CO₂ is considerably stronger. For all three catalysts, these effects increase with temperature. Kinetic parameters for the inhibiting effects of CO₂ and H₂O over the three perovskites were determined. Addition of methane to the feed (NO/CH₄=4) increases conversion of NO to N₂ about two to four times, depending on the initial NO concentration and on temperature. This, however, is still much too low for practical applications. Furthermore, the rates of methane oxidation by nitric oxide over perovskites are substantially slower than those of methane oxidation by oxygen. Thus, perovskites do not seem to be suitable for catalytic selective NO reduction with methane.     

Low-temperature H2-SCR of NO on a novel Pt/MgO-CeO2 catalyst

The selective catalytic reduction of NO by H₂ under strongly oxidizing conditions (H₂-SCR) in the low-temperature range of 100–200 °C has been studied over Pt supported on a series of metal oxides (e.g., La₂O₃, MgO, Y₂O₃, CaO, CeO₂, TiO₂, SiO₂ and MgO-CeO₂). The Pt/MgO and Pt/CeO₂ solids showed the best catalytic behavior with respect to N₂ yield and the widest temperature window of operation compared with the other single metal oxide-supported Pt solids. An optimum 50 wt% MgO-50wt% CeO₂ support composition and 0.3 wt% Pt loading (in the 0.1–2.0 wt% range) were found in terms of specific reaction rate of N₂ production (mols N₂/g_cat s). High NO conversions (70–95%) and N₂ selectivities (80–85%) were also obtained in the 100–200 °C range at a GHSV of 80,000 h⁻¹ with the lowest 0.1 wt% Pt loading and using a feed stream of 0.25 vol% NO, 1 vol% H₂, 5 vol% O₂ and He as balance gas. Addition of 5 vol% H₂O in the latter feed stream had a positive influence on the catalytic performance and practically no effect on the stability of the 0.1 wt% Pt/MgO-CeO₂ during 24 h on reaction stream. Moreover, the latter catalytic system exhibited a high stability in the presence of 25–40 ppm SO₂ in the feed stream following a given support pretreatment. N₂ selectivity values in the 80–85% range were obtained over the 0.1 wt% Pt/MgO-CeO₂ catalyst in the 100–200 °C range in the presence of water and SO₂ in the feed stream. The above-mentioned results led to the obtainment of patents for the commercial exploitation of Pt/MgO-CeO₂ catalyst towards a new NO_x control technology in the low-temperature range of 100–200 °C using H₂ as reducing agent. Temperature-programmed desorption (TPD) of NO, and transient titration of the adsorbed surface intermediate NO_x species with H₂ experiments, following reaction, have revealed important information towards the understanding of basic mechanistic issues of the present catalytic system (e.g., surface coverage, number and location of active NO_x intermediate species, NO_x spillover).     

La2O3助剂对甲烷干燥重整催化剂 Ni-γ-Al2O3支撑作用的研究简

The nature of support and type of active metal affect catalytic performance. In this work, the effect of using La203 as promoter and support for Ni/γ-A1203 catalysts in dry reforming of methane was investigated. The reforming reactions were carried out at atmosphenc pressure in the temperature range of 500-2700℃. The activity and stability of the catalyst, carbon formation, and syngas （H2/CO） ratio were determined. Various techniques were applied for characterization of both fresh and used catalysts. Addition of La2O3 to the catalyst matrix improved the dispersion of Ni and adsorption of CO2, thus its activity and stability enhanced.     

Reforming of methane with carbon dioxide to synthesis gas over supported Rh catalysts

Reforming of methane with carbon dioxide to synthesis gas (CO/H₂) has been investigated over rhodium supported on SiO₂, TiO₂, γ-Al₂O₃, MgO, CeO₂, and YSZ (ZrO₂ (8 mol% Y₂O₃)) catalysts in the temperature range of 650–750°C at 1 bar total pressure. A strong carrier effect on the initial specific activity, deactivation rate, and carbon accumulation was found to exist. A strong dependence of the specific activity of the methane reforming reaction on rhodium particle size was observed over certain catalysts. Tracing experiments (using ¹³CH₄) coupled with temperature-programmed oxidation (TPO) revealed that the carbon species accumulated on the surface of the Rh/Al₂O₃ catalyst during reforming reaction at 750°C are primarily derived from the CO₂ molecular route. The amount of carbon present on the working catalyst surface which is derived from the CH₄ molecular route is found to be very small.     

The simultaneous activation of methane and carbon dioxide to C2 hydrocarbons under pulse corona plasma over La2O3/γ-Al2O3 catalyst

The pulse corona plasma has been used as an activation method for reaction of methane and carbon dioxide, the product was C₂ hydrocarbons and by-products were CO and H₂. Methane conversion and the yield of C₂ hydrocarbons were affected by the carbon dioxide concentration in the feed. The conversion of methane increased with increasing carbon dioxide concentration in the feed whereas the yield of C₂ hydrocarbons decreased. The synergism of La₂O₃/γ-Al₂O₃ and plasma gave methane conversion of 24.9% and C₂ hydrocarbons yield of 18.1% were obtained at the power input of plasma was 30 W. The distribution of C₂ hydrocarbons changed by using Pd-La₂O₃/γ-Al₂O₃ catalyst, the major C₂ product was ethylene.     

Catalytic clean-up of emissions from small-scale combustion of biofuels

A knitted silica-fibre was prepared and used as support for combustion catalysts. Different Pd–MeO and Pt–MeO (Me=Ni, Co, Cu and Mn) catalysts were prepared, and their catalytic activities were investigated in the conversion of gas mixtures consisting of methane, ethene, naphthalene (model PAH), carbon monoxide, carbon dioxide, nitrogen and water vapour in the temperature range 150–800°C. Combinations of Pd–Ni and Pt–Ni were found to result in decreased light-off temperatures in methane combustion. The Pd–Ni/silica-fibre catalyst exhibited a light-off temperature in methane combustion of ca 220°C lower than that obtained over the Pd/silica-fibre catalyst. Deactivation of the catalysts was observed by subjecting the catalysts to reaction mixture flow at 800°C for 6 h. For the Pd-containing catalysts, the deactivation was considered to be due to both support and metal sintering as well as changes in the nature of the Pd–O species. The catalysts were characterised by N₂-adsorption, H₂-adsorption, O₂–TPD and H₂–TPR.     

Integrated high temperature gas cleaning: Tar removal in biomass gasification with a catalytic filter

A nickel-based catalytic filter material for the use in integrated high temperature removal of tars and particles from biomass gasification gas was tested in a broad range of parameters allowing the identification of the operational region of such a filter. Small-scale porous alumina filter discs, loaded with approximately 2.5 wt% Al₂O₃, 1.0 wt% Ni and 0.5 wt% MgO were tested with a particle free synthetic gasification gas with 50 vol% N₂, 12 vol% CO, 10 vol% H₂, 11 vol% CO₂, 12 vol% H₂O, 5 vol% CH₄ and 0–200 ppm H₂S, and the selected model tar compounds: naphthalene and benzene. At a typical face velocity of 2.5 cm/s, in the presence of H₂S and at 900 °C, the conversion of naphthalene is almost complete and a 1000-fold reduction in tar content is obtained. Technically, it would be better to run the filter close to the exit temperature of the gasifier around 800–850 °C. At 850 °C, conversions of 99.0% could be achieved in typical conditions, but as expected, only 77% reduction in tars was achieved at 800 °C.

Conversion data can be reasonably well described with first order kinetics and a dominant adsorption inhibition of the Ni sites by H₂S. The apparent activation energies obtained are similar to those reported by other investigators: 177 kJ/mol for benzene and 92 kJ/mol for naphthalene. The estimated heat of adsorption of H₂S is 71 kJ/mol in the benzene experiments and 182 kJ/mol in the naphthalene experiments, which points at very strong adsorption of H₂S. Good operation of the present material can hence only be guaranteed at temperatures above 830 °C mainly due to the strong deactivation by H₂S at lower temperatures.     

Comparison of supports for the direct synthesis of hydrogen peroxide from H2 and O2 using Au–Pd catalysts

The direct synthesis of hydrogen peroxide from H₂ and O₂ using a range of supported Au–Pd alloy catalysts is compared for different supports using conditions previously identified as being optimal for hydrogen peroxide synthesis, i.e. low temperature (2 °C) using a water–methanol solvent mixture and short reaction time. Five supports are compared and contrasted, namely Al₂O₃, -Fe₂O₃, TiO₂, SiO₂ and carbon. For all catalysts the addition of Pd to the Au only catalyst increases the rate of hydrogen peroxide synthesis as well as the concentration of hydrogen peroxide formed. Of the materials evaluated, the carbon-supported Au–Pd alloy catalysts give the highest reactivity. The results show that the support can have an important influence on the synthesis of hydrogen peroxide from the direct reaction. The effect of the methanol–water solvent is studied in detail for the 2.5 wt% Au–2.5 wt% Pd/TiO₂ catalyst and the ratio of methanol to water is found to have a major effect on the rate of hydrogen peroxide synthesis. The optimum mixture for this solvent system is 80 vol.% methanol with 20 vol.% water. However, the use of water alone is still effective albeit at a decreased rate. The effect of catalyst mass was therefore also investigated for the water and water–methanol solvents and the observed effect on the hydrogen peroxide productivity using water as a solvent is not considered to be due to mass transfer limitations. These results are of importance with respect to the industrial application of these Au–Pd catalysts.     

Partial oxidation of ethane to synthesis gas over Co-loaded catalysts

Attention has been increasingly paid to the partial oxidation of lower alkanes to synthesis gas, due to its intrinsic energy saving process. We studied the partial oxidation of ethane (POE) on Co loaded on various supports. The POE performance varied as follows: Y₂O₃, CeO₂, ZrO₂, La₂O₃  SiO₂, Al₂O₃, TiO₂ > MgO. Comparing Y₂O₃ and CeO₂, the carbon deposition during the POE was negligible on CeO₂ and therefore CeO₂ was the most preferable support. By changing space velocity and O₂ partial pressure, reaction mechanism of POE was studied and it was revealed that two-step mechanism was prevailing; combustion of ethane to H₂O and CO₂ and subsequent reforming of ethane with H₂O and CO₂ to synthesis gas. Co/CeO₂ catalyst exhibited high and stable catalytic activity for 10 h; high ethane conversion of 18% (maximum ethane conversion 20% at O₂/C₂H₆ = 0.2) with H₂ and CO selectivities of 93 and 84%, respectively.     

CNG engines exhaust gas treatment via Pd-Spinel-type-oxide catalysts

Four spinel-type catalysts AB₂O₄ (CoCr₂O₄, MnCr₂O₄, MgFe₂O₄ and CoFe₂O₄) were prepared and characterized by XRD, BET, TEM and FESEM techniques. The activity of these catalysts towards the combustion of methane was evaluated in a temperature-programmed combustion (TPC) apparatus. Spinel-type-oxides containing Cr at the B site were found to provide the best results. The half-conversion temperature of methane over the CoCr₂O₄ catalyst was 376 °C with a W/F = 0.12 g s/cm⁻³. On the basis of temperature-programmed oxygen desorption (TPD) analysis as well as of catalytic combustion runs, the prevalent activity of the CoCr₂O₄ catalyst could be explained by its higher capability to deliver suprafacial, weakly chemisorbed oxygen species. This catalyst, promoted by the presence of 1 wt% of palladium deposited by wet impregnation, was lined on cordierite monoliths and then tested in a lab-scale test rig. The combination of Pd and CoCr₂O₄ catalysts enables half methane conversion at 330 °C (GHSV = 10,000 h⁻¹), a performance similar to that of conventional 4 wt% Pd-γ-Al₂O₃ catalysts but enabled with just a four-fold lower amount of noble metal.