Removal of basic dyes from aqueous solution by low-cost adsorbent: Wood apple shell (Feronia acidissima)

The adsorption of two basic dyes, methylene blue (MB) and crystal violet (CV) on wood apple shell (WAS) were investigated using a batch adsorption technique. A series of experiments were undertaken in an agitated batch adsorber to assess the effect of the system variables such as solution pH, dye concentration and temperature. Removal of dyes was observed to be most effective at higher pH. Freundlich and Langmuir isotherm models were applied to the equilibrium data. The results showed that Langmuir equation fits better than the Freundlich equation. It was observed that the WAS adsorbent showed higher adsorption capacity for crystal violet (130 mg/g) than methylene blue (95.2 mg/g). The FTIR studies indicate that the interaction of dye and WAS surface is via the nitrogen atoms of the adsorbate and oxygen groups of the adsorbent. The adsorption of dyes onto WAS proceeds according to a pseudo-second-order model. Thermodynamic parameters such as free energy (ΔG°), enthalpy (ΔH°) and entropy (ΔS°) were also calculated. The studies show that WAS, a lignocellulosic inexpensive material, can be an alternative to other expensive adsorbents used for dye removal in wastewater treatment.     

Various carbon-based MgAl2O4 adsorbents and their removal efficiency of CR dye and antibiotics in aqueous media: High selective adsorption capacity,performance prediction and mechanism insight

Various carbon -based MgAl₂O₄ (MAO) adsorbents were synthesized by a simple ultrasound irradiation technology with the activated carbon (AC), carbon quantum dots (CQDs), C₃N₄ (CN) and graphene oxide (GO) as carbon sources. The optimum synthesis conditions for the carbon -based MAO adsorbents were determined by the study of the addition of different types of carbon and different mass ratios of m_{Various carbon}: m_MAO = 2.5%, 5.0%, 7.5% and 10%. The carbon -based MAO adsorbents were used for the adsorption of Congo red (CR) dye, tetracycline hydrochloride (TCH), oxytetracycline hydrochloride (OCH), ciprofloxacin (CIP), naproxen sodium (NPS) and tetrabromobisphenol A (TBBPA) and the seven factors affecting the adsorption behavior were discussed, including the type of carbon, AC content, initial dye concentration (C_CR), adsorbent dosage (C_{carbon -based MAO adsorbents}), adsorption time (A_t), pH value and reaction temperature (T). The corresponding adsorption isotherm models such as Langmuir, Tempkin, Koble-Corrigan, Toth and Freundlich models and thermodynamics of carbon -based MAO adsorbents for the adsorption of CR dye were also studied. When pH = 7.8, C_CR = 200 mg/L, A_t = 90 min, T = 287 K and C_{AC 5.0 wt%-MAO} = 1 g/L, the removal rate of CR dye reaches 89.7%. The back propagation (BP) neural network model was used to predict the adsorption percentage of carbon-based MAO adsorbents, which was consistent with the experimental results. The high adsorption capacity of AC 5.0 wt%-MAO adsorbents for the adsorption of CR dye can be assigned to the synergistic effects of electrostatic interaction, intermolecular force, n-π interaction and hydrogen bonding, while for the adsorption of TCH, OCH and CIP can be ascribed to the electrostatic interaction. This study demonstrated a huge potential of carbon -based MAO adsorbents as an eco-friendly adsorbent for the adsorption of dyes and drugs.     

Poly(Acrylamide-Sepiolite) Composite Hydrogels: Preparation, Swelling and Dye Adsorption Properties

Summary Polymer-clay hydrogel composite was prepared on the basis of polyacrylamide (PAAm) gel containing the clay mineral sepiolite. The properties of swelling and dye adsorption of poly(acrylamide-sepiolite) (AAm/Sep) composite hydrogel were investigated. The parameters of swelling and diffusion in water and dye solutions were calculated for the AAm and AAm/Sep hydrogels. It was found that the equilibrium swelling degree of obtained composite higher than that of AAm gel. Spectroscopic analysis of composite and composite-dye systems was done with FT-IR method. Adsorption of monovalent cationic dyes such as Basic Blue 12 (BB-12) Basic Blue 9 (BB-9), and Basic Violet 1 (BV-1), was studied on the composite. In the adsorption experiments, S (Sigmoidal) type for composite gel adsorption isotherms in the Giles classification system was found. Adsorption studies indicated that the amounts of adsorbed dyes on the AAm/Sep composite hydrogel were increased with following order; BB-12 > BB-9 > BV-1. The composite hydrogel may be considered as good candidate for environmental application to retain more water and dyes.     

Novel type of alginate gel‐based adsorbents for heavy metal removal

Various alginate gel‐based adsorbents were investigated for the removal of heavy metals: alginate beads, alginate capsules, and alginate gel‐coated adsorbent. Of these, alginate capsules showed the greatest Pb²⁺ uptake capacity of 1560 mg g^?1 of dry sodium alginate, and the alginate gel‐coated adsorbent, prepared simply by forming a thin alginate film on an inert matrix, achieved rapid adsorption equilibrium within 10 min. Adsorbed metals were readily removed from the alginate gel‐based adsorbents using eluents such as HNO₃ and could be reused for up to 10 adsorption–desorption cycles without marked loss of metal uptake capacity. Alginate gel‐coated adsorbents could be prepared in a dried state and have great application potential for the removal of heavy metals from contaminated water. Copyright © 2004 Society of Chemical Industry     

Preparation of interpenetrating polymer network gel beads for dye absorption

Preparation of interpenetrating polymer network (IPN) gel beads for dye absorption was carried out by using simultaneous crosslinking method. First, sodium alginate (SA), 3‐(methacrylamido) propyl trimethyl ammonium chloride (MAPTAC), and/or acrylamide (AM), K₂S₂O₈, and N,N′‐methylenebisacrylamide (MBAM) were mixed in aqueous solution. The beads were prepared using K₂S₂O₈ and MBAM as the initiator and crosslinking agent, respectively. Then, the solution was dropped into CaCl₂ solution mixed with N,N,N′,N′‐tetramethylethylenediamine (TMEDA). The former was used as the crosslinking agent of alginate and the latter was used as the accelerator for the polymerization of monomer in the alginate solution. The gel bead composed of only alginate was also prepared to compare the properties with IPN gel bead. The components in IPN gel bead were examined by FTIR analysis. The factors effecting the particle size of alginate and IPN gel beads were investigated. In alginate gel bead, the concentration of solution affected the particle size, whereas type of monomer affected the particle size of IPN gel bead. The IPN gel bead had smooth surface (from SEM results), different from the alginate bead. Alginate content caused the swelling behavior of dried IPN beads. Cationic dye was absorbed by crosslinked alginate gel bead. The absorption of reactive dye by IPN gel bead was a result of its cationic charge. The absorption density of IPN gel beads was the reciprocal of the absorbent dosage. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1585–1591, 2006     

Adsorption of dyes on activated carbons: influence of surface chemical groups

The surface chemistry of a commercial activated carbon has been selectively modified, without changing significantly its textural properties, by means of chemical treatments, using HNO₃, H₂O₂, NH₃, and thermal treatments under a flow of H₂ or N₂. The resultant samples were characterized in terms of their surface chemistry and textural properties, and subsequently tested in the removal of different classes of dyes. It was shown that the surface chemistry of the activated carbon plays a key role in dye adsorption performance. The basic sample obtained by thermal treatment under H₂ flow at 700 °C is the best material for the adsorption of most of the dyes tested. For anionic dyes (reactive, direct and acid) a close relationship between the surface basicity of the adsorbents and dye adsorption was shown, the interaction between the oxygen-free Lewis basic sites and the free electrons of the dye molecule being the main adsorption mechanism. For cationic dyes (basic) the acid oxygen-containing surface groups show a positive effect but thermally treated samples still present good performances, showing the existence of two parallel adsorption mechanisms involving electrostatic and dispersive interactions. The conclusions obtained for each dye individually were confirmed in the colour removal from a real textile process effluent.     

Synthesis and characterization of Na‐alginate/acrylamide hydrogel and its application in dye removal

Sodium‐alginate/acrylamide (Na‐alginate/AAm) cross‐linked hydrogel was prepared by using gamma irradiation. The gel content and the water absorbency behavior of the obtained hydrogel were investigated. The thermal and morphological properties of the prepared hydrogel were studied using thermogravimetric analysis and scanning electron microscopy. The thermal stability of Na‐alginate significantly changed when mixed with AAm. The adsorption of basic violet 7 dye on the prepared hydrogel was studied under different experimental conditions. The adsorption process for the basic dye was proven pH dependent. The maximum amount adsorbed (mg/g) of the Na‐alginate/AAm for the dye was found to be 78.1.0 mg/g at pH 9.0. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

The Binding of Anionic Dyes by Cross-Linked Cationic Starches

Adsorption of anionic dyes on the cross-linked with epichlorohydrin starches containing quaternary ammonium groups (CCS) was investigated and compared with that of modified starches containing only quaternary ammonium groups (CS). The adsorption of anionic dyes on CS and CCS closely follows the Langmuir model of adsorption. The computed Langmuir saturation capacity Q _o increases with increasing degree of substitution (DS) of CS or CCS and has the value from 0.81 mol/kg to 3.22 mol/kg for CCS and from 0.88 mol/kg to 1.87 mol/kg for CS. The effectiveness of the cationic groups in dye binding was about 1 mol/equiv for CSS with DS from 0.47 to 0.62 and all the cationic groups had attached one anionic groups of the dye. Increasing DS of CS decreases the effectiveness of dye binding due to the increase in solubility of CS, and the soluble part of CS binds the dye as a typical soluble polyelectrolyte. CCS are more suitable than CS for the anionic dye adsorption from a textile dyeing solution. DS of CCS should be about 0.5–0.6. They adsorb the anionic dyes in few minutes and acts in the wide range of pH of the solutions. The Langmuir saturation capacity Q _o and the effectiveness of the cationic groups in dye binding increase with an increase of the adsorption temperature. The positive values of the enthalpy and entropy suggest that the adsorption is endothermic and during the adsorption of the anionic dye on CCS the randomness of the system increases.     

In2S3-Polymer Hybrid Gels Derived from In(III) Metal–Organic Gels for Dye Adsorption,Photodegradation, and Bacteria Removal

Currently, the treatment of wastewater that contains organic dyes and bacteria attracts a considerable amount of attention, and the fabrication of photoinduced catalytic materials to address the problem is still a challenge. In this work, indium(III) sulfide hybrid gels are prepared by in situ polymerization and sulfurization using In(III) metal–organic gels as sacrificial templates. Two In(III) metal–organic gels are fabricated by the coordination interaction between multitopic pyridyl ligands and indium ions, where the assembled structure of the gel templates can be tuned by employing different multitopic ligands to obtain the networks of nanofibers and nanoparticles. After templated fabrication, the resulting In₂S₃-polymer hybrid gels show improved mechanical strength, and can be used as novel photocatalysts for the photodegradation of organic dyes, such as rhodamine B and methylene blue, and efficient adsorbents for the adsorption of anionic dyes, such as Congo red. Experiments that involve pure and mixed bacteria demonstrate the bacteria-removing activities of the hybrid gels due to their electrostatic adsorption and photoinduced sterilization of the bacteria. Therefore, this new kind of hybrid gel might have potential applications in the photoinduced purification of water by scavenging organic dyes and bacteria in the aqueous phase.     

A novel hydrogel based on agricultural waste for removal of hazardous dyes from aqueous solution and reuse process in a secondary adsorption

A novel hydrogel based on the orange peel (OP) and N-vinyl-2-pyrrolidone was prepared by free-radical polymerization using gamma irradiation. The effect of radiation dose and hydrogel composition on gel content was studied. The formed hydrogel was characterized by FT-IR, TGA, and SEM. The swelling behavior was determined as a function of swelling time, pH, and OP content. The hydrogel swelling was found to be pH dependent, and the diffusion mechanism of water into the hydrogel was found Fickian. The developed hydrogel was used for the removal of Congo red (CR) and methyl orange (MO) dyes from wastewater. The effects of various operating parameters, such as initial pH, contact time, initial dye concentration, and temperature on the removal of dyes, have been investigated. The Langmuir and the Freundlich adsorption models were applied to study the adsorption isotherm. The pseudo-first-order model was proved compatible for CR adsorption and the pseudo-second-order model well described the adsorption of MO. The adsorption of dyes increased with increasing temperature indicating that the endothermic nature of the adsorption process and the thermodynamic parameters was evaluated. Second, the adsorption cycle of dyes was also examined and discussed utilizing the loaded hydrogel with the other dye and cobalt metal ions.     

Chitosan intercalated montmorillonite: Preparation, characterization and cationic dye adsorption

Chitosan intercalated montmorillonite (Chi-MMT) was prepared by dispersing sodium montmorillonite (Na⁺-MMT) into chitosan solution at 60 °C for 24 h. The Chi-MMT was characterized by XRD, XRF and FT-IR. The intercalation was accomplished via the ion-exchange of Na⁺ ions with –NH₃⁺ of chitosan, resulting in the expansion of d₀₀₁ from 1.42 nm of Na⁺-MMT to 2.21 nm of Chi-MMT. The chitosan content in the Chi-MMT measured by TGA was about 17 mass%. The adsorption capacity of Chi-MMT was investigated in comparison with the starting Na⁺-MMT and chitosan using three different cationic dyes, i.e. basic blue 9 (BB9), basic blue 66 (BB66) and basic yellow 1 (BY1). The Chi-MMT showed the highest adsorption capacity in the range of 46–49 mg/g when the initial dye concentration was 500 mg/L, being equivalent to 92–99 wt.% of dye removal. The adsorption capacities of Chi-MMT for all basic dyes increased with an increase of initial dye concentration. An increase of adsorption capability of Chi-MMT was attributed to the existence of intercalate-chitosan. It could enlarge the pore structure of Chi-MMT, facilitating the penetration of macromolecular dyes, and also electrostatically interact with the applied dyes. These results indicated the competency of Chi-MMT adsorbent for basic dye adsorption.     

Synthesis of Novel Biocompatible Composite Fe3O4/ZrO2/Chitosan and Its Application for Dye Removal

A novel biocompatible composite Fe₃O₄/ZrO₂/chitosan was synthesized in a simple way and its capacity of dye removal was investigated in this study. The morphology of the material was examined by SEM and TEM and found to be nanosized and spheroidal. Equilibrium adsorption isotherms and dynamic behaviors of the adsorption process were investigated in detail. The material saturated with dye could be regenerated by treatment with strong alkali solution. The composite has high adsorption capacity towards acidic dyes represented by amaranth and tartrazine, and remains intact under conditions that are strongly acidic or alkali. The material has high potential to be applied for the removal of acidic dyes in industrial wastewater in large scale.     

Preparation and rheology of titanium dioxide nanoparticles loaded κ-carrageenan hydrogel beads strengthened by mixed salts for multipollutant water remediation

Hydrogel beads are emerging as alternate adsorbent material for the batch or continuous column treatment of dye wastewater. Polysaccharide-based gel beads are preferred for their uniform shape and size, large specific surface area, and easy separation by filtration and subsequent reuse. In this work, we prepare and rheologically characterize UV-active κ-carrageenan/TiO₂ beads for the adsorption and degradation of dyes. The 3–4 mm sized nanocomposite beads are formed by the extrusion of κ-carrageenan/TiO₂ gel solution in salt solutions. The maximum increase in modulus was observed with the addition of 1% w/v TiO₂ to κ-carrageenan and subsequent crosslinking with mixed salt of KCl and CaCl₂. κ-carrageenan/TiO₂ beads crosslinked by mixed salt of KCl and CaCl₂ have higher adsorption capacity, as compared to beads crosslinked with single salt of KCl. The kinetic study indicated the chemisorption of Methylene Blue on the bead surface. κ-carrageenan/TiO₂ beads showed higher degradation for Methylene Blue and Nile Blue A than Rhodamine B in 5 and 50 ppm each multicomponent dye systems under UV irradiation. The κ-carrageenan/TiO₂ beads could form a porous column for the selective adsorption of positively charged dyes from a multicomponent dye system.     

Adsorption of methylene blue from aqueous solutions by modified expanded graphite powder

The modified expanded graphite (MEG) powder was used as a porous adsorbent for the removal of the cationic dye, methylene blue (MB), from aqueous solutions. The dye adsorption experiments were carried out with the bath procedure. Experimental results showed that the basic pH, increasing initial dye concentration and high temperature favored the adsorption. The dye adsorption equilibrium was attained rapidly after 5 min of contact time. Experimental data related to the adsorption of MB on the MEG under different conditions were applied to the pseudo-first-order equation, the pseudo-second-order equation and the intraparticle diffusion equation, and the rate constants of first-order adsorption (k₁), the rate constants of second-order adsorption (k₂) and intraparticle diffusion rate constants (k_int) were calculated, respectively. The experimental data fitted very well in the pseudo-second-order kinetic model. The thermodynamic parameters of activation such as Gibbs free energy, enthalpy, and entropy were also evaluated. The results indicated that the MEG powder could be employed as an efficient adsorbent for the removal of textile dyes from effluents.     

The usability of (sodium alginate/acrylamide) semi-interpenetrating polymer networks on removal of some textile dyes

In this study, (sodium alginate/acrylamide) interpenetrating polymer networks ((NaAlg/AAm)IPN) have been prepared at definite composition. The aqueous solution of 3% (w/v) sodium alginate and 50% (w/v) acrylamide was irradiated with ⁶⁰Co-γ rays at a dose rate of 0.07 kGy/h up to 5 kGy. The percent conversion was determined gravimetrically and 100% gelation was achieved at 5 kGy dose. To understand whether the semi-interpenetrating polymer network of sodium alginate is performed, Fourier Transform Infrared (FTIR) spectra of polyacrylamide (PAAm), sodium alginate, and the semi-interpenetrating polymer network were recorded. It is found that the FTIR spectra of PAAm, NaAlg, and the semi-interpenetrating polymer network are different. The thermograms of PAAm, sodium alginate, and the semi-interpenetrating polymer network were recorded for investigating their thermal character. (NaAlg/AAm)IPN hydrogels were immersed to swell in a solution of pH 7, at a temperature of 25°C. The swelling results at pH 7.0 indicated that (NaAlg/AAm)IPN hydrogel, containing 3% NaAlg showed maximum % swelling in water but swelling increased in the order of water > Magenta > Methylene Blue > Safranine-O > Methyl Violet. Diffusion of water and aqueous solution of dyes within (NaAlg/AAm)IPN hydrogels was found to be of Fickian character at the initial stage of swelling with regard to values calculated for diffusion coefficient of (NaAlg/AAm)IPN hydrogels in water and aqueous solution of dyes. Some diffusion parameters were calculated from swelling of (NaAlg/AAm)IPN in water and dyes and their adsorption isotherms were plotted. In the adsorption experiments, the efficiency of (NaAlg/AAm)IPN hydrogels to adsorb Magenta, Safranine-O, Methylene Blue, and Methyl Violet dyes from water was studied. (NaAlg/AAm)IPN hydrogels showed different adsorption for different aqueous solution of dyes at pH 7.0. Adsorption isotherms were constructed for (NaAlg/AAm)IPN-dye systems. S type adsorption in the Giles classification system was found. Thermal and spectroscopic characterization of semi-interpenetrating polymer network of sodium alginate and acrylamide and dye adsorbed semi-interpenetrating polymer network of sodium alginate and acrylamide was recorded. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

The adsorption of malachite green (MG) as a cationic dye onto functionalized multi walled carbon nanotubes

Synthetic dyes are widely used by several industries to color their products. The discharge of colored wastewater into the hydrosphere causes serious environmental problems. We used functionalized multi wall carbon nanotubes as an adsorbent for the adsorption of cationic dye, malachite green, from aqueous solution. Based on information provided by the Iranian Research Institute of Petroleum Industry, carbon nanotubes are produced using a chemical vapor deposition (CVD) technique. These as-received MWCNTs were functionalized by acid treatment. The remaining dye concentration was read by UV-visible absorption spectroscopy at maximum adsorption wavelength. The effect of different operational parameters such as contact time, pH of solution, adsorbent dose and initial dye concentration were studied. The results showed that by increasing of contact time, pH and adsorbent dose the removal of dye increased, but by increasing initial dye concentration, the removal efficiency decreased. Adsorption isotherms and kinetics behavior of f-MWCNTs for removal of malachite green was analyzed, and fitted to various existing models. The experimental data were well correlated with the Langmuir isotherm with a maximum adsorption capacity (q _m ) and regression coefficient (R²) of 142.85 mg/g and 0.997, respectively. The results of this study indicate that functionalized multi wall carbon nanotubes can be used as an effective adsorbent for the removal of dyes.     

Poly(acrylamide/laponite) nanocomposite hydrogels: Swelling and cationic dye adsorption properties

Super adsorbent polyacrylamide (PAAm)/nanoclay (laponite, Lap) hydrogels were prepared by in situ free radical polymerization of AAm in an aqueous solution with clay as a crosslinker. The swelling properties and water‐soluble cationic dye adsorption behaviors of the PAAm/laponite (PAAm/Lap) nanocomposite (NC) hydrogels were investigated. The parameters of swelling and diffusion of water in dye solutions were evaluated for the PAAm/Lap NC hydrogels. The adsorption behavior of the monovalent cationic dyes such as Basic Blue 12 (BB 12), Basic Blue 9 (BB 9), and Basic Violet 1 (BV 1), were studied on the NC hydrogels. The effects of the clay content of the hydrogel on its cationic dye uptake behavior were studied. The adsorption studies indicated that the rates of dye uptake by the NC hydrogels increased in the following order: BB 9 > BB 12 > BV 1. This order is similar to the swelling results of the PAAm/Lap NC hydrogel in the dye solutions. The equilibrium uptakes of the different dyes by the PAAm/Lap NC hydrogel were nearly the same. In the dye absorption studies, S‐type adsorption in the Giles classification system was found for the BB 12 and BV 1 dyes, whereas L ‐type was observed for the BB 9 dye. After the heat treatment of PAAm/Lap, the rate of dye uptake and equilibrium dye uptake were increased. The NC hydrogels may be considered as a good candidate for environmental applications to retain more water and to remove dyes. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Spectroscopic study of interactions between model direct dyes and cotton

Although examined for years, interactions between direct dyes and the chemical structure of cotton cellulose remain an interesting, and still not entirely known, chemical phenomenon occurring in the fiber. Ten model azo dyes have been studied in aqueous solution, as dye powders and on cotton fabric using ¹³C MAS NMR and UV–visible spectroscopy. NMR spectroscopy indicates that model azo dyes, especially dye 8, interact by π‐stacking at the central biphenyl group, and that there is hydrogen bonding with cellulose. Model azo dyes are present as the azo or hydrazone tautomer. The UV–visible λ_max indicate that shifts are attributed to adsorption of model azo dyes into cellulose surfaces. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 758–766, 2007     

Synthesis of Glutamic Acid Derived Organogels and their Applications in Dye Removal from Aqueous Medium

To develop glutamic acid derived cross‐linked polymeric organogels for dye adsorption from aqueous media, dimethyl 2‐(methacrylamido)pentanedioate (Glu‐MAC) is polymerized using diethylene glycol dimethacrylate as cross‐linker via the reversible addition‐fragmentation chain transfer (RAFT) technique to synthesize cross‐linked polymeric organogels with pendant glutamate moieties. The mechanical properties of organogels are examined by rheological study. The organogels exhibit higher value of storage modulus (G′) than the loss modulus (G′′) within the linearity limits of deformation, and strong dependence of G′ values on the extent of cross‐linking in the gel matrix. Field emission scanning electron microscopy shows porous structure of the gel matrix, therefore, organogels are able to exhibit swelling behaviors in organic solvents such as dichloromethane, N,N‐dimethylformamide, tetrahydrofuran, acetone, and methanol. Dye adsorption properties of these organogels are investigated using different aqueous dye solutions, such as crystal violet (CV), malachite green (MG), rhodamine‐B, and uranine. The gels show high dye adsorption capacities (≥97%) toward cationic dyes like CV and MG.     

Dye removal from colored‐textile wastewater using chitosan‐PPI dendrimer hybrid as a biopolymer: Optimization,kinetic, and isotherm studies

Preparation of a biopolymer chitosan‐polypropylene imine (CS‐PPI) as a biocompatible adsorbent and its reactive textile dyes removal potential were performed. Chemical specifications of CS‐PPI were determined using Fourier transform infrared, ¹H‐NMR, and ¹³C‐NMR. The surface morphology of the CS‐PPI surface was characterized by scanning electron microscopy. Results confirmed that the linkages between the NH₂ groups of PPI dendrimer and carboxylic groups of modified Chitosan were accomplished chemically. Two textile reactive dyes, reactive black 5 (RB5) and reactive red 198 (RR198), were used as model compounds. A response surface methodology was applied to estimate the simple and combined effects of the operating variables, including pH, dye concentration, time contact, and temperature. Under the optimal values of process parameters, the dye removal performance of 97 and 99% was achieved for RB5 and RR198, respectively. Furthermore, the isotherm and kinetic models of dyes adsorption were performed. Adsorption data represented that both examined dye followed the Langmuir isotherm. The adsorption kinetics of both reactive dyes were satisfied by pseudo‐second order equation. Based on this study, CS‐PPI due to having high adsorption capacity (6250 mg/g for RB5 and 5882.35 mg/g for RR198), biocompatibility and ecofriendly properties might be a suitable adsorbent for removal of reactive dyes from colored solutions. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013