孔隙率对水热合成Bi2Te3热电性能的影响

用水热法制备了晶粒尺寸为几十纳米到几百纳米的Bi₂Te₃粉末,再通过压片法制得不同孔隙率的Bi₂Te₃薄片材料,研究了孔隙率对Bi₂Te₃热电性能的影响。通过对热电性能的测试,研究发现压片法制得的Bi₂Te₃样品具有较高的孔隙率,且样品的热传导符合多孔材料的热传导规律。当Bi₂Te₃样品孔隙率较大时具有较低的热导率,在室温下测得孔隙率为43%的Bi₂Te₃薄片热导率为0.282W·m^-1·K^-1。材料热导率、电导率和ZT值均随孔隙率的增加而减小。     

Sn掺杂Bi2Te2.7Se0.3薄膜材料的微结构及热电性能研究

采用真空熔炼法合成(Bi<,1-x>Sn<,x>)<,2>Te<,2.7>Se<,0.3>合金,再通过热蒸发技术在473K玻璃基体上沉积了厚800nm的Sn掺杂Bi<,2>Te<,2.7>Se<,0.3>热电薄膜.利用X射线衍射技术对薄膜的相结构进行表征;采用表面粗糙度测量仪测定薄膜厚度;采用四探针法和温差电动势法分别测量薄膜的电阻率和Seebeck系数:采用薄膜的电阻率和Seebeck系数Sn掺杂浓度对(Bi<,1-x>Sn<,x>)<,2>Te<,2.7>Se<,0.3>薄膜热电性进行分析.结果表明,Sn掺杂浓度为0.003时,热电功率因子提高到12.8μW/K<'2>·cm;Sn掺杂浓度从0.004增加到0.01,薄膜为P型半导体,热电功率因子减小.     

Ga、K双掺杂对N型Bi_2Te_(2.7)Se_(0.3)材料热电性能的影响

采用真空熔炼及热压方法制备了Ga和K双掺杂N型Bi2Te2.7Se0.3热电材料。XRD分析结果表明,Ga和K已经完全固溶到Bi2Te2.7Se0.3晶体结构中,形成了单相固溶体合金。SEM分析表明,材料组织致密且有层状结构特征。通过Ga和K部分替代Bi,在300~500 K的大部分温度范围内,Ga和K双掺杂对提高Bi2Te2.7Se0.3的Seebeck系数产生了积极的作用,同时双掺杂样品的电导率也得到明显的提高。Ga和K双掺杂样品的热导率都大于未掺杂的Bi2Te2.7Se0.3,Ga0.02Bi1.94K0.04Te2.7Se0.3合金在500 K获得ZT最大值为1.05。     

Cu掺杂SnSe晶体生长及热电性能研究

利用坩埚下降法成功制备了具有标准Pnma空间群结构的Cu掺杂SnSe晶体，其尺寸为φ18 mm×55 mm,Cu元素在晶体中均匀分布。该晶体为P型半导体材料，电导率在600 K附近具有最低值4.53 S·cm^-1，载流子浓度在830 K下达到1.69 cm×1 019 cm,Seebeck系数最大值为739.5μV·K^-1，出现在500 K附近。功率因子PF随温度升高始终增加，830 K下为4.80μW·cm^-1·K^-2。热电性能ZT在800 K附近达到最高值0.83，说明该晶体是一种潜在的中温区热电材料。     

热喷涂制Ni阻挡层在碲化铋热电器件中的应用

在碲化铋热电制冷器件的服役过程中，焊料与热电材料间的元素扩散将严重制约器件的正常使用，目前最常用在两者间加Ni阻挡层的方法来改善这种问题，以往采用电镀、等离子烧结等制备Ni镀层的方法会产生界面镀层厚度不易控制、镀层易氧化的问题，而热喷涂由于其镀速快、镀层厚度易控制和镀后表面较平整、耐氧化、结合强度高等优点，可作为制备Ni阻挡层的更好选择。采用热喷涂技术制备不同厚度的Ni阻挡层，并对其分别进行200℃下24、72和144 h的退火试验。首先探究不同Ni层厚度的p型(Bi_0.4Sb_1.6Te₃)和n型(Bi₂Te_2.7Se_0.3)碲化铋材料退火前后对镀层硬度和防扩散效果的影响，并将不同Ni层厚度的p、n型碲化铋材料制备成热电器件进行服役性能测试。结果表明：退火对p型材料镀Ni层硬度影响较小，其值变化在10%以内，但对n型材料镀Ni层的硬度影响较大，其最大硬度值下降56.36%;Ni是p型碲化铋材料较好的扩散阻挡层，能显著减少Bi_0.4Sb...     

Sb掺杂对Mg_2Si基化合物热电性能的影响(英文)

采用感应熔炼和真空热压的方法制备了Sb掺杂和未掺杂的Mg2Si基热电材料.研究了Sb掺杂对Mg2Si基热电材料的结构以及热电特性的影响.结果表明:通过Sb掺杂使得载流子浓度从3.07x1019 cm-3增加到1.25x1020 cm-3,电子有效质量也相应增加.测试了从室温到800 K下试样的Seebeck系数,电导率和热导率.结果显示,0.3 at%Sb掺杂使得电导率得到显著增加,在783 K时,ZT值达到0.7.     

La掺杂P型CeyFe3CoSb12热电材料及涂层的热电性能

采用熔融-退火-放电等离子烧结工艺合成P型CoSb₃基热电材料，研究Ce掺杂量对CoSb₃基热电材料显微组织和热电性能的影响，以及La掺杂对解耦热电关系的作用。结果表明，掺杂元素La和Ce降低了热导率，使La_0.1Ce_0.8Fe₃CoSb₁₂在整个测温区间的热导率保持在1 W/(m·K)左右，对应的最高热电优值在723 K时达到0.45。以磁控溅射法制备Al-Ni涂层，通过对溅射Al-Ni防护涂层的P型La_0.1Ce_0.8Fe₃CoSb₁₂材料热电性能进行测试，发现涂层的介入并未造成材料热电性能的衰退，且涂层与基底结合良好，元素分布均匀。以钎料Ag40Cu60对P型热电元件La_0.1Ce_0.8Fe₃CoSb₁₂与电极片Mo50Cu50接头进行焊接行为研究，发现界面处宏观结合效果良好。     

Cu_(y)Bi_(2)Te_(2.62)S_(0.08)Se_(0.3)热电材料的微观结构与热电性能EI北大核心CSCD

采用合金设计、真空熔炼、快速凝固、球磨制粉、冷压成形和常压烧结工艺,制备了Cu、S掺杂的n型Bi_(2)Te_(2.7)Se_(0.3)热电材料,采用XRD、SEM和ZEM-3热电测试系统等表征热电材料晶体结构、微观形貌和热电性能,研究Cu、S掺杂的n型Bi_(2)Te_(2.7)Se_(0.3)热电材料热电性能机理。结果表明:Cu_(y)Bi_(2)Te_(2.62)S_(0.08)Se_(0.3)热电材料晶体结构为R-3m空间群斜方晶系的六面体层状结构;掺杂Cu的Cu_(y)Bi_(2)Te_(2.7)Se_(0.3)热电材料,形成Cui间隙缺陷和Bi′Te反位缺陷,随着载流子(电子)浓度增加,载流子迁移率降低,电导率显著增大;掺杂S的Bi_(2)Te_(2.62-z)SzSe_(0.3)热电材料,生成化学键健能较Bi-Te强的Bi-S,抑制反位缺陷Bi′Te形成,少数(空穴)载流子浓度减小,同时增强声子对声子散射和点缺陷对声子散射,从而使晶格热导率和双极扩散热导率降低,总热导率明显降低,抑制塞贝克系数的减少;Cu、S共掺杂的协同作用,n型Cu_(y)Bi_(2)Te_(2.62-z)SzSe_(0.3)热电材料电导率增大,而热导率基本不变,由此ZT值和功率因子显著提高;在300~400 K温度范围内,Cu_(0.03)Bi_(2)Te_(2.62)S_(0.08)Se_(0.3)的电导率约为7.0×10^(4)S/m,塞贝克系数约为220μV/K,功率因子约为2.4 m W/(m·K^(2)),热电优值(ZT值)约为1.0。Cu_(0.03)Bi_(2)Te_(2.62)S_(0.08)Se_(0.3)热电材料可广泛应用于低温尤其室温条件下的热电制冷器件和温差发电电池。     

定向凝固Ag掺杂Mg3Sb2合金热电性能

通过定向凝固方法可以高效制备Mg₃Sb₂晶体,根据凝固理论计算了平界面生长临界速率,在此速率下可以有效抑制第二相Sb的析出。对不同的凝固速率下的Mg₃Sb₂晶体微观组织进行了分析,表明凝固速率为5μm·s^-1时可以有效减少Mg空位的出现,并在晶体中获得过量Mg原子,有利于更好地提升热电性能。通过消除晶界和Ag元素掺杂有效提升了Mg₃Sb₂晶体的载流子迁移率和浓度,在测试温度区间(300～800K)内,最大电导率值可达309S·cm^-1,同时保持了较高的Seebeck系数值,从而获得了更好的电子传输性能(PF_max=1.2mW·m^-1·K^-2),通过Hall测试和第一性原理计算对此结果进行了验证。Ag掺杂浓度为2.5at%下相应的热电优值最高可以达到0.67,此方法为Mg₃Sb₂基热电材料性能优化提供了新的...     

Ga、K双掺杂P型Bi_(0.5)Sb_(1.5)Te_3材料的制备及热电性能

采用真空熔炼和热压方法制备了Ga和K双掺杂Bi0.5Sb1.5Te3热电材料。XRD结果表明,Ga0.02Bi0.5Sb1.48-x Kx Te3块体材料的XRD图谱与Bi0.5Sb1.5Te3的XRD图谱对应一致,但双掺杂样品的衍射峰略微向左偏移。热压块体材料中存在明显的(00l)晶面择优取向。SEM形貌表明材料组织致密且有层状结构特征。Ga和K双掺杂可使Bi0.5Sb1.5Te3在室温附近的Seebeck系数有一定的提高,而双掺杂样品的电导率均得到了不同程度的提高,其中Ga0.02Bi0.5Sb1.42K0.06Te3样品的电导率得到较明显的改善。在300~500 K测量温度范围内,所有双掺杂样品的热导率高于Bi0.5Sb1.5Te3的热导率,在300 K附近双掺杂样品的ZT值得到提高,其中Ga0.02Bi0.5Sb1.42K0.06Te3样品在300 K时ZT值达到1.5。     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

Thermodynamics Study on the Decomposition of Chromite with KOH

Institute of Process Engineering, Chinese Academy of Sciences, China, has proposed a method for oxidative leaching of chromite with potassium hydroxide. Understanding the mechanism of chromite decomposition, especially in the potassium hydroxide fusion, is important for the optimization of the operating parameters of the oxidative leaching process. A traditional thermodynamic method is proposed and the thermal decomposition and the reaction decomposition during the oxidative leaching of chromite with KOH and oxygen is discussed, which suggests that chromite is mainly destroyed by reactions with KOH and oxygen. Meanwhile, equilibrium of the main reactions of the above process was calculated at different temperatures and oxygen partial pressures. The stable zones of productions, namely, K2CrO4 and Fe2O3, increase with the decrease of temperature, which indicates that higher temperature is not beneficial to thermodynamic reactions. In addition, a comparison of the general alkali methods is carried out, and it is concluded that the KOH leaching process is thermodynamically superior to the conventional chromate production process.     

Influence of Heat Treatment on Damping Behaviour of the Magnesium Wrought Alloy AZ61

The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

Quantitative Analysis of the Crystallographic Orientation Relationship Between the Martensite and Austenite in Quenching–Partitioning–Tempering Steels

The orientation relationships(ORs)between the martensite and the retained austenite in low-and medium-carbon steels after quenching–partitioning–tempering process were studied in this work.The ORs in the studied steels are identified by selected-area electron diffraction(SAED)as either K–S or N–W ORs.Meanwhile,the ORs were also studied based on numerical fitting of electron backscatter diffraction data method suggested by Miyamoto.The simulated K–S and N–W ORs in the low-index directions generally do not well coincide with the experimental pole figure,which may be attributed to both the orientation spread from the ideal variant orientations and high symmetry of the low-index directions.However,the simulated results coincide well with experimental pole figures in the high-index directions{123}_(bcc).A modified method with simplicity based on Miyamoto’s work was proposed.The results indicate that the ORs determined by modified method are similar to those determined by Miyamoto’method,that is,the OR is near K–S OR for the low-carbon Q–P–T steel,and with the increase of carbon content,the OR is closer to N–W OR in medium-carbon Q–P–T steel.     

Using Finite Element and Contour Method to Evaluate Residual Stress in Thick Ti-6Al-4V Alloy Welded by Electron Beam Welding

This work was to reveal the residual stress profile in electron beam welded Ti-6Al-4V alloy plates(50 mm thick) by using finite element and contour measurement methods.A three-dimensional finite element model of 50-mmthick titanium component was proposed,in which a column–cone combined heat source model was used to simulate the temperature field and a thermo-elastic–plastic model to analyze residual stress in a weld joint based on ABAQUS software.Considering the uncertainty of welding simulation,the computation was calibrated by experimental data of contour measurement method.Both test and simulated results show that residual stresses on the surface and inside the weld zone are significantly different and present a narrow and large gradient feature in the weld joint.The peak tensile stress exceeds the yield strength of base materials inside weld,which are distinctly different from residual stress of the thin Ti-6Al-4V alloy plates presented in references before.     

Microstructures and Tensile Properties of Ultrafine-Grained Ni–(1–3.5) wt% SiC_(NP) Composites Prepared by a Powder Metallurgy Route

Silicon carbide nanoparticle-reinforced nickel-based composites(Ni–Si CNP),with a Si CNPcontent ranged from1 to 3.5 wt%,were prepared using mechanical alloying and spark plasma sintering.In addition,unreinforced pure nickel samples were also prepared for comparative purposes.To characterize the microstructural properties of both the unreinforced pure nickel and the Ni–Si CNPcomposites transmission electron microscopy(TEM) was used,while their mechanical behavior was investigated using the Vickers pyramid method for hardness measurements and a universal tensile testing machine for tensile tests.TEM results showed an array of dislocation lines decorated in the sintered pure nickel sample,whereas,for the Ni–Si CNPcomposites,the presence of nano-dispersed Si CNPand twinning crystals was observed.These homogeneously distributed Si CNPwere found located either within the matrix,between twins or on grain boundaries.For the Ni–Si CNPcomposites,coerced coarsening of the Si CNPassembly occurred with increasing Si CNPcontent.Furthermore,the grain sizes of the Ni–Si CNPcomposites were much finer than that of the unreinforced pure nickel,which was considered to be due to the composite ball milling process.In all cases,the Ni–Si CNPcomposites showed higher strengths and hardness values than the unreinforced pure nickel,likely due to a combination of dispersion strengthening(Orowan effects) and particle strengthening(Hall–Petch effects).For the Ni–Si CNPcomposites,the strength increased initially and then decreased as a function of Si CNPcontent,whereas their elongation percentages decreased linearly.Compared to all materials tested,the Ni–Si CNPcomposite containing 1.5% Si C was found more superior considering both their strength and plastic properties.     

Directional Growth of Tin Crystals Controlled by Combined Solute Concentration Gradient Field and Static Magnetic Field

A new method was introduced to achieve directional growth of Sn crystals. Microstructures in liquid(Pb)/liquid(Sn) diffusion couples were investigated under various static magnetic fields. Results show that the β-Sn crystals mainly reveal an irregular dendritic morphology without or with a relatively low static magnetic field(B0.3 T). When the magnetic field is increased to 0.5 T, the β-Sn dendrites close to the final stage of growth begin to show some directional character. With a further increase in the magnetic field to a higher level(0.8–5 T), the β-Sn dendrites have an enhanced directional growth character, but the dendrites show a certain deflection. As the magnetic field is increased to 12 T, the directional growth of the β-Sn dendrites in the center of the couple is severely destroyed. The mechanism of the directional growth of the β-Sn crystals and the deflection of the β-Sn crystals with the application of static magnetic field was tentatively discussed.     

电化学噪声数据处理方法概述

综述了常见的电化学噪声数据处理方法,介绍了直流趋势剔除、统计分析、快速傅立叶变换(FFT)法计算功率谱密度(PSD)以及小波变换处理电化学噪声信号的基本过程,并阐释了各种数学处理及所得参数的物理意义。