Novel D-π-A system based on zinc porphyrin dyes for dye-sensitized solar cells: Synthesis, electrochemical, and photovoltaic properties

We have designed and synthesized novel zinc porphyrin dyes which have a D-π-A system based on porphyrin derivatives containing a triphenylamine (TPA) electron-donating group and a phenyl carboxyl anchoring group substituted at the meso position of the porphyrin ring, yielding the push-pull porphyrins as the most efficient green dye for dye-sensitized solar cell (DSSC) applications. The synthesis and characterization of a novel D-π-A system based on zinc-porphyrin derivatives have been investigated through their photophysical and photoelectrochemical studies. A large red-shift of the absorption maxima due to introduction of the TPA moiety at the meso position of the porphyrin ring was expected in the D-π-A porphyrins, but the absorption maxima of HKK-Por dyes were a little red-shifted in contrast to Zn[5,-10,15-triphenyl-20-(4-carboxylphenyl)-porphyrin], due to the tilted structure between TPA and the porphyrin unit. Under the photovoltaic performance measurement, the maximum incident photon-to-current conversion efficiency (IPCE) value of the DSSC based on HKK-Por 5 was slightly higher than the efficiencies of the DSSCs based on other HKK-Por dyes due to the introduction of the alkoxy group into the TPA moiety at the meso position of the porphyrin ring. A maximum photon-to-electron conversion efficiency of 3.36% was achieved with the DSSC based on HKK-Por 5 dye (J_SC = 9.04 mA/cm², V_OC = 0.57 V, FF = 0.66) under AM1.5 irradiation (100 m Wcm⁻²).     

Carbon nanotubes-polyethylene oxide composite electrolyte for solid-state dye-sensitized solar cells

Novel carbon nanotubes (CNTs)-polyethylene oxide (PEO) composite electrolyte for dye-sensitized solar cell (DSSC) was prepared and characterized for the first time. The strong bonding and interaction between CNTs and PEO in CNTs-PEO composites was observed by the characterization of X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and Raman spectra. The introduction of CNTs into PEO matrix significantly improved the electrolyte properties of DSSC such as roughness, amorphicity and ionic conductivity. The solid-state DSSC fabricated with the optimum composite electrolyte (added 1% CNTs in PEO matrix, 1%CNT-PEO) achieved maximum conversion efficiency of 3.5%, an open circuit voltage (V_OC) of 0.589 V, short circuit current density (J_SC) of 10.64 mA/cm² and fill factor (FF) of 56%. The highest IPCE in the DSSC fabricated with 1%CNT-PEO electrolyte is ascribed to the improved ionic conductivity of composite electrolytes and enhanced interfacial contact between electrode and electrolyte.     

Structure and photovoltaic properties of ZnO nanowire for dye-sensitized solar cells

Aligned ZnO nanowires with different lengths (1 to approximately 4 μm) have been deposited on indium titanium oxide-coated glass substrates by using the solution phase deposition method for application as a work electrode in dye-sensitized solar cells (DSSC). From the results, the increases in length of zinc oxide (ZnO) nanowires can increase adsorption of the N3 dye through ZnO nanowires to improve the short-circuit photocurrent (J_sc) and open-circuit voltage (V_oc), respectively. However, the J_sc and V_oc values of DSSC with ZnO nanowires length of 4.0 μm (4.8 mA/cm² and 0.58 V) are smaller than those of DSSC with ZnO nanowires length of 3.0 μm (5.6 mA/cm² and 0.62 V). It could be due to the increased length of ZnO nanowires also resulted in a decrease in the transmittance of ZnO nanowires thus reducing the incident light intensity on the N3 dye. Optimum power conversion efficiency (η) of 1.49% was obtained in a DSSC with the ZnO nanowires length of 3 μm.     

Improved photovoltaic performances of Ru (II) complex sensitized DSSCs by co-sensitization of carbazole based chromophores

Herein, we report photovoltaic performance studies of three carbazole based dyes (N_1–3) derived from (Z)-3-(9-hexyl-9H-carbazol-3-yl)-2-(thiophen-2-yl)acrylonitrile scaffold as effective co-sensitizers in Ru (II) complex, i.e. NCSU-10 sensitized DSSCs. From the results it is evident that, the device fabricated using co-sensitizer N₃ with 0.2 mM of NCSU-10 exhibited improved photon conversion efficiency (PCE) of 8.73% with J_SC of 19.87 mA·cm^− 2, V_OC of 0.655 V and FF of 67.0%, while N₁ displayed PCE of 8.29% with J_SC of 19.75 mA·cm^− 2, V_OC of 0.671 V and FF of 62.6%, whereas NCSU-10 (0.2 mM) alone displayed PCE of 8.25% with J_SC of 20.41 mA·cm^− 2, V_OC of 0.667 V and FF of 60.6%. However, their EIS studies confirm that, N₁, showing higher V_OC is efficient in suppressing the undesired charge recombination in DSSCs through enhanced surface coverage on TiO₂ and thereby resulting in longer electron lifetime than that of NCSU-10 dye alone. Here, the higher PCE of N₃ can be attributed to its improved light harvesting efficiency, which is due to the presence of highly electron withdrawing barbituric acid in its structure. Conclusively, the results showcase the potential of simple carbazole based dyes as co-sensitizers in improving efficiency of DSSCs.     

Alkyloxy substituted organic dyes for high voltage dye-sensitized solar cell: Effect of alkyloxy chain length on open-circuit voltage

Three novel organic dyes (SB1, SB2, and SB3) containing 4-(hexyloxy)-N-(4-(hexyloxy)phenyl)-N-phenylaniline as electron donor and cyanoacrylic acid as electron acceptor bridged by alkyloxy (methyl = SB1, propyl = SB2 and hexyl = SB3) substituted p-phenylenevinylene linkers have been synthesized. Density functional theory (DFT) has employed to study electron distribution and intramolecular charge transfer. Increase in alkyl chain length in alkyloxy substituent leads to increase in open-circuit voltage (V_OC), which is found to be related to the increased electron lifetime at open-circuit condition. Under AM 1.5 G 1 sun light illumination (100 mW/cm²), an optimized SB3-sensitized cell show a short-circuit photocurrent density (J_SC) of 12.83 mA/cm², an open-circuit voltage (V_OC) of 0.745 V and a fill factor (FF) of 0.64, corresponding to an overall conversion efficiency (η) of 6.12%. Little degradation in η observed over 40 days is indicative of long-term stability of the SB-series dyes.     

Polymer solar cells fabricated with 4,8-bis(2-ethylhexyloxy)benzo[1,2-b:4,5-b′]dithiophene and alkyl-substituted thiophene-3-carboxylate-containing conjugated polymers: Effect of alkyl side-chain in thiophene-3-carboxylate monomer on the device performance

Four alkyl-substituted thiophene-3-carboxylate containing donor–acceptor (D–A) copolymers were designed, synthesized, and characterized. Thiophene-3-carboxylate was used as a weak electron acceptor unit in the copolymers to provide a deeper highest occupied molecular orbital (HOMO) level for obtaining a higher open-circuit voltage in polymer solar cells (PSCs). The resulting bulk heterojunction PSCs, made of the copolymers and [6,6]-phenyl-C71-butyric acid methyl ester (PC₇₁BM), exhibited different short circuit currents (J_SCs) and open-circuit voltages (V_OCs), depending on the length of alkyl side-chain in the thiophene-3-carboxylate unit. Among all fabricated photovoltaic (PV) devices, PC2:PC₇₁BM (1:1 wt. ratio) showed the highest efficiency with the highest J_SC of 10.5 mA/cm². Although PC5:PC₇₁BM (1:1) displayed the highest V_OC of 0.93 V, the device efficiency was observed to be poor, which is due to poor nanophase segregation. This comparison shows that the side-chain of thiophene carboxylate in these copolymers plays a very important role in the device efficiency.     

Influence of seed layer treatment on low temperature grown ZnO nanotubes: Performances in dye sensitized solar cells

Non-aligned and highly densely aligned ZnO nanotube (NTs), synthesized by low temperature solution method were applied as photoanode materials for the fabrication of efficient dye-sensitized solar cells (DSSCs). The crystalline and the morphological analysis revealed that the grown aligned ZnO NTs possessed a typical hexagonal crystal structure of outer and inner diameter ∼250 nm and ∼100 nm, respectively. ZnO seeding on FTO substrates is an essential step to achieve the aligned ZnO NTs. A DSSC fabricated with aligned ZnO NTs photoanode achieved high solar-to-electricity conversion efficiency of ∼2.2% with short circuit current (J_SC) of 5.5 mA/cm², open circuit voltage (V_OC) of 0.65 V and fill factor (FF) of 0.61. Significantly, the aligned ZnO NTs photoanode showed three times improved solar-to-electricity conversion efficiency than DSSC fabricated with non-aligned ZnO NTs. The enhanced performances were credited to the aligned morphology of ZnO NTs which executed the high charge collection and the transfer of electrons at the interfaces of ZnO NTs and electrolyte layer.     

Organic dyes with oligo-n-hexylthiophene for dye-sensitized solar cells: Relation between chemical structure of donor and photovoltaic performance

Organic dyes with the oligohexylthiophene linkage having several donor parts, carbazole, indole, and indoline, were newly synthesized as sensitizers for dye-sensitized solar cells. The carbazole was most efficient donor moiety for DSSCs among these dyes with the oligothiophene linkage. Carbazole dyes were adsorbed with larger amount of molecules on the TiO₂ film than both indole dyes and indoline dyes. Therefore, both the V_OC and the electron lifetime of DSSCs with the carbazole dyes were highly observed. The decreasing of J_SC of DSSCs with indole and indoline dyes also caused by the reducing the adsorption amount of dyes.     

Organic dyes incorporating the cyclopentadithiophene moiety for efficient dye-sensitized solar cells

Three triarylamine organic dyes (XS28-30) containing a cyclopentadithiophene unit as the conjugated bridge have been designed and synthesized for a potential application in dye-sensitized solar cells (DSSCs). Their absorption spectra, electrochemical and photovoltaic properties have been investigated. The incorporation of ethyl-substituted cyclopentadithiophene is highly beneficial to light-harvesting and preventing close π-π aggregation, thus favorably generating high efficiency. For a typical device, a solar energy conversion efficiency (η) of 5.8% based on XS29 was achieved under simulated AM 1.5 solar irradiation (100 mW cm⁻²) with a short-circuit photocurrent density (J_SC) of 14.4 mA cm⁻², an open-circuit voltage (V_OC) of 601 mV, and a fill factor (ff) of 0.68. These results suggest that the functionalized cyclopentadithiophene unit is a promising candidate for DSSCs.     

Synthesis and solar cells applications of EO‐PF‐DTBT polymer

Poly{[2,7‐(9,9‐bis‐(1‐(2‐(2‐methoxyethoxy)ethoxy)ethyl)‐fluorene)]‐alt‐[5,5‐(4,7‐di‐2′‐thienyl‐2,1,3‐benzothiadiazole)]} (EO‐PF‐DTBT) was synthesized by Suzuki coupling reaction. The polymer is soluble in common organic solvent, such as toluene, THF, and chloroform, and it also shows solubility in polar solvent, such as cyclopentanone. Solar cells based on EO‐PF‐DTBT and PC₆₁BM show maximum power conversion efficiency of 2.65% with an open circuit voltage (V_OC) of 0.86 V, a short circuit current density (J_SC) of 6.10 mA/cm², and a fill factor of 51% under AM 1.5G illumination at 100 mW/cm², which is the best results for fluorene and 4,7‐di‐2‐thienyl‐2,1,3‐benzothiadiazole copolymers and PC₆₁BM blend. The 1,8‐diiodooctane can work well to reduce the over‐aggregated phase structure in polymer solar cells. Our results suggest that the introducing high hydrophilic side chain into conjugated polymer donor materials can tune the aggregation structure and improve the solar cells performances. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40478.     

Open circuit voltage increase by substituted spacer and thieno[3,4-c]pyrrole-4,6-dione for polymer solar cells

We reported on two donor polymers containing thieno[3,4-c]pyrrole-4,6-dione(TPD) derivatives as electron withdrawing units for organic photovoltaics (OPVs). To control molecular weight and solubility of polymers, hexyl side chains are inserted to thiophene spacers. Due to the electron donating characteristic of hexyl side chains, highest occupied molecular orbital (HOMO) energy level of polymer is decreased as 0.18 eV, whereas the open circuit voltage is increased to 1.08 V. When bulk heterojunction devices were fabricated, the best PCE value of 0.360% (V_OC = 0.89 V, J_SC = 1.2 mA/cm², FF = 36.3%) under 100 mW/cm² irradiation.     

The Effect of Incorporation of Multi-Walled Carbon Nanotube into Poly(Ethylene Oxide) Gel Electrolyte on the Photovoltaic Performance of Dye-Sensitized Solar Cell

Gel polymer electrolytes (GPEs) consist of poly(ethylene oxide) (PEO), sodium iodide (NaI) and different amount of multi-walled carbon nanotubes (MWCNT) were prepared. The conductivity study revealed that the highest ionic conductivity of GPE was 7.02 × 10^?3 S cm^?1. The structural and complexation between the materials are authenticated via X-ray diffraction (XRD) and Fourier transform infrared (FTIR) spectroscopy. Under the exposure of AM 1.5, the fabricated DSSCs exhibited the highest photoenergy conversion efficiency of 7.23% with a short circuit current density (J_SC) of 18.64 mA cm^?2, open circuit voltage (V_OC) of 0.590 mV and fill factor (FF) of 65.7%.     

Influences of Ga concentration on performances of CuInGaSe2 cells fabricated by sputtering-based method with ceramic quaternary target

Copper Indium Gallium Selenide (Cu(In,Ga)Se₂, CIGSe) absorbers with different Ga contents were prepared by sputtering CIGSe ceramic targets and post-annealing. CIGSe solar cell devices were fabricated with other functional layers. The device performances and absorber properties were investigated. Increasing Ga content led to an increase in V_OC and a decrease in J_SC. Ga was supposed to diffuse towards back contact during the annealing process. The best performance was obtained as the ratio of Ga/(In + Ga) reaches 0.32 with the efficiency of 13.8% and a V_OC of 537 mV.     

Performance improvement of dye-sensitizing solar cell by semi-rigid triarylamine-based donors

Novel organic dyes (IDB and ISB dyes), which contain 5-phenyl-iminodibenzyl (IDB) and 5-phenyl-iminostilbene (ISB) as electron donors and a cyanoacrylic acid moiety as an electron acceptor and an anchoring group, connected with a thiophene as a π-conjugated system, have been synthesized and used as the sensitizers for dye-sensitized solar cells (DSSCs). The photophysical and electrochemical properties of the dyes were investigated by absorption spectrometry, cyclic voltammetry and density functional theory calculations. As demonstrated, the IDB and ISB unit exhibited stronger electron-donating ability and broader absorption spectra when coated onto TiO₂. The DSSC based on ISB-2 consisting of ISB unit produced 5.83% of η (J_sc = 13.14 mA cm⁻², V_oc = 0.64 V, and ff = 0.68) under 100 mW cm⁻² simulated AM 1.5 G solar irradiation.     

Nanoarchitecture of variable sized graphene nanosheets incorporated into three-dimensional graphene network for dye sensitized solar cells

A novel three-dimensional (3D) nanoarchitecture consisting of hybrid graphene nanosheets (GNs)/graphene foam (GF) was fabricated on the FTO conducting substrate as a high efficient counter electrode (CE) for dye sensitized solar cells (DSSCs). The GNs with various sized such as large-sized heat-reduced graphene nanosheets (H-GNs) and small-sized laser-reduced graphene quantum dots (L-GQDs) were synthesized and used as catalytic materials incorporated into a 3D GF network, respectively. In this design, the aggregations and restacking of GNs were efficiently reduced, which is beneficial for increasing the amount of the active defective sites at the edges of graphene to the electrolyte solution. Especially, L-GQDs with smaller dimension less than 100 nm have more active defective sites at edges, providing superiority over the large-sized H-GNs in terms of electrocatalytic activity. Meanwhile, the GF network with high conductivity provides fast electron transport channels for charge injection between the GNs and FTO. The DSSC with this hybrid CE exhibited energy conversion efficiency (η) of 7.70% with an open circuit voltage (V_OC), short circuit photocurrent density (J_SC) and fill factor (FF) of 760 mV, 15.21 mA cm⁻², and 72.0%, respectively, which is comparable to that of the conventional Pt CE (7.68%).     

Enhancing the performance of dye-sensitized solar cells based on an organic dye by incorporating TiO2 nanotube in a TiO2 nanoparticle film

The photoelectrochemical properties of a high molar extinction coefficient charge transfer organic dye containing thienylfluorene segment called FL, and the effect of incorporating TiO₂ nanotube (TiNT) in TiO₂ nanoparticle film along with the above dye on the photovoltaic performance of dye-sensitized solar cells (DSSCs) were investigated. The influence of soaking time of the TiO₂ electrode in dye solution and the effect of varying its concentration, on the solar cell efficiency was also studied. Cyclic voltammetric (CV) analysis revealed the linear relationship between the anodic peak current and the scan rate, indicating a surface-confined diffusion process.The surface morphology of TiNT was characterized using SEM, TEM and XRD. The open-circuit voltage (V_OC) of the DSSC increased with the increase in the wt% of TiNT and shows optimal value at about 5 wt%, which is correlated with the suppression of the electron recombination as found out from the electron lifetime studies.The electrochemical impedance spectroscopy (EIS) technique was employed to quantify the charge transport resistance (R_ct) and electron lifetime under different ratios of the TiNT/nanoparticle. The electron lifetimes of the DSSCs based on FL and N3 dye were very close to one another and the DSSC based on the FL showed respectable photovoltaic performance of ca. 7.8% under the light intensity of 100 mW cm⁻² (AM 1.5G).     

New diketo-pyrrolo-pyrrole (DPP) sensitizer containing a furan moiety for efficient and stable dye-sensitized solar cells

A new metal-free organic sensitizer containing a furan moiety as the π-spacer based on the diketo-pyrrolo-pyrrole unit was synthesized through simple synthetic routes and with low cost for the application of dye-sensitized solar cells. Two corresponding dyes with benzene and thiophene spacers were also synthesized for the purpose of comparison. On the basis of optimized DSSC test conditions, the sensitizer containing the furan shows prominent solar energy conversion efficiency (η) of 5.65% (J_sc = 15.96 mA cm⁻², V_oc = 541 mV, ff = 0.65) under simulated full sunlight irradiation. The dyes were also tested in a solvent-free ionic liquid electrolyte devices and the stability of devices was performed over 2000 h at full sunlight. The sensitizer containing the furan moiety exhibited good stability and better photovoltaic performance of up to 4.41% power conversion efficiency.     

Synthesis of new N, N-diphenylhydrazone dyes for solar cells: Effects of thiophene-derived π-conjugated bridge

Four novel D-π-A hydrazone dyes (HT, HM, HE, and HO) with an N, N-diphenylhydrazone moiety as the electron donor, different thiophene-derived π-conjugated bridges and a cyanoacrylic acid moiety as the electron acceptor have been designed and synthesized for the application in dye-sensitized solar cells. The influences of thiophene-derived bridges on the photoelectrochemical and photovoltaic performance of these hydrazone dyes were investigated. Results demonstrate that the introduction of 3,4-dialkyloxythiophene could red-shift the dye’s absorption spectrum due to the enhancement of the electron-donating ability of π-conjugated bridges. Importantly, electrochemical impedance spectroscopy analysis reveal that 3,4-dialkyloxythiophene bridge could change the charge recombination resistance at the TiO₂/dye/electrolyte interface and as a result to improve the open-circuit photovoltage. Among the four dyes, HO exhibits the maximum power conversion efficiency of 5.83% (V_oc = 0.65 V, J_sc = 12.69 mA/cm², FF = 0.707) under simulated AM 1.5 irradiation (100 mW/cm²).     

Improving the performance of dye-sensitized solar cells with TiO2/graphene/TiO2 sandwich structure

This study investigates the extent to which the TiO₂/graphene/TiO₂ sandwich structure improves the performance of dye-sensitized solar cells (DSSCs) over that of DSSCs with the traditional structure. Studies have demonstrated that the TiO₂/graphene/TiO₂ sandwich structure effectively enhances the open circuit voltage (V_oc), short-circuit current density (J_sc), and photoelectrical conversion efficiency (η) of DSSCs. The enhanced performance of DSSCs with the sandwich structure can be attributed to an increase in electron transport efficiency and in the absorption of light in the visible range. The DSSC with the sandwich structure in this study exhibited a V_oc of 0.6 V, a high J_sc of 11.22 mA cm^-2, a fill factor (FF) of 0.58, and a calculated η of 3.93%, which is 60% higher than that of a DSSC with the traditional structure.     

Synthesis, characterization, and photovoltaic property of a low band gap polymer alternating dithienopyrrole and thienopyrroledione units

The lower the highest occupied molecular orbital (HOMO) energy level of the conjugated polymer is, the higher the open-circuit voltage (V_OC) of the obtained polymer solar cell (PSC) is. To achieve this goal, a new conjugated polymer (PDTPTPD) alternating dithienopyrrole (DTP) and thienopyrroledione (TPD) units was designed and synthesized by Stille coupling reaction. Through UV-vis absorption and cyclic voltammetry (CV) measurements, it was found that the resulting copolymer exhibited both a low optical band gap of 1.62 eV and a low HOMO energy level of −5.09 eV owing to the electronegativity of TPD moiety. Preliminary photovoltaic study disclosed that the PSC based on PDTPTPD:PCBM ([6,6]-phenyl-C₆₁ butyric acid methyl ester) blend showed a power conversion efficiency (PCE) of 1.9%, with a V_OC of 0.70 V, and a short circuit current (I_SC) of 6.97 mA/cm², suggesting that PDTPTPD is a promising photovoltaic polymer.