不同类型的离子表面活性剂对甲苯的增溶作用

通过电导法测定SDBS、CTAB、FMES 3种离子表面活性剂水溶液在25,30,35℃时的临界胶束浓度(CMC),并依据CMC和范特霍夫方程计算了3种体系下的ΔH■、ΔS■和ΔG■,测定无机盐(NaCl、Na_2SO_4)和有机物(乙醇、十二醇)对表面活性剂增溶甲苯的影响。结果表明,3种体系下ΔG■均为负,这说明3种表面活性剂在水溶液中均易于形成胶团;3种离子表面活性剂的CMC大小顺序与对甲苯溶解量的大小顺序不同,说明CMC大小并不是影响甲苯增溶的唯一因素;添加一定量有机物[n(乙醇)∶n(FMES)=1∶4]或者无机盐(0.2 mol/L浓度的NaCl)对甲苯增溶效果更好。     

不同类型的离子表面活性剂对甲苯的增溶作用

通过电导法测定SDBS、CTAB、FMES 3种离子表面活性剂水溶液在25,30,35℃时的临界胶束浓度(CMC),并依据CMC和范特霍夫方程计算了3种体系下的ΔH■、ΔS■和ΔG■,测定无机盐(NaCl、Na_2SO_4)和有机物(乙醇、十二醇)对表面活性剂增溶甲苯的影响。结果表明,3种体系下ΔG■均为负,这说明3种表面活性剂在水溶液中均易于形成胶团;3种离子表面活性剂的CMC大小顺序与对甲苯溶解量的大小顺序不同,说明CMC大小并不是影响甲苯增溶的唯一因素;添加一定量有机物[n(乙醇)∶n(FMES)=1∶4]或者无机盐(0.2 mol/L浓度的NaCl)对甲苯增溶效果更好。     

不同表面活性剂对单相微乳液特性的影响

表面活性剂是影响微乳液特性的关键因素之一。本文选取聚氧乙烯脱水山梨醇单油酸酯（Tween 80）、烷基糖苷1214（APG 1214）、十二烷基苯磺酸钠（SDBS）、脂肪醇聚氧乙烯醚硫酸钠（AES）、十二烷基硫酸钠（SDS）和95%纯度鼠李糖脂（R-95%）这6种表面活性剂,通过对其乳化性能和临界胶束浓度进行筛选,结合其形成微乳液的拟三元相图、粒径分布和界面张力分析其特性,并提出微乳液增溶油能力和增溶油成本。研究表明：APG 1214、SDBS、Tween 80乳化性能好、临界胶束浓度低具有更易形成微乳液的优势;5种表面活性剂（Tween 80、SDBS、APG 1214、SDS、AES）均可与正丁醇、水和3号白油自发形成单相微乳液,单相区面积大小为AES型>SDS型>APG 1214型>Tween 80型>SDBS型,最大增溶油能力大小为SDS型>AES型>APG 1214型>Tween 80型>SDBS型,最低增溶油成本大小为AES型相似文献   

表面活性剂对气体水合物生成过程的定量影响

为确定HCFC?141b水合物生成条件下阴离子表面活性剂十二烷基硫酸钠(SDS)和十二烷基苯磺酸钠(SDBS)的临界胶束浓度(CMC),在0~20℃温度下,通过圆环法实验研究了不同浓度表面活性剂溶液体系的表面张力,考察了表面活性剂对溶液体系表面张力的影响机理并通过C3H8水合物的生成过程实验进行了验证,确定了SDS和SDBS的临界胶束浓度. 结果表明,当SDS和SDBS的质量浓度分别低于500?10?6和100?10?6时,表面活性剂降低水表面张力的效果最明显,二者的CMC分别为1950?10?6和400?10?6,表面活性剂能明显缩短水合反应的诱导时间,提高了其平均生成速率.     

添加剂的浓度对非离子表面活性剂AEO9浊点的影响

各类添加剂都能对非离子表面活性剂的浊点产生影响.今研究了离子型表面活性剂、增溶物和电解质类添加剂在不同浓度下对非离子表面活性剂AEO9浊点的影响.其中离子型表面活性剂和增溶物类添加剂可在极低的浓度上改变AEO9的浊点,且随着添加剂加入浓度的增加,AEO9的浊点也逐渐增加,当添加剂浓度达到离子型表面活性剂或增溶物的临界胶束浓度时,AEO9的浊点将出现急剧上升.而电解质类添加剂对AEO9浊点的影响表现出具有临界浓度现象,只有当添加剂的浓度达到相应的临界浓度之后,具有盐析效应的电解质将使AEO9浊点线性下降,而具有盐溶效应的电解质则使AEO9浊点线性升高,且不同电解质相应的临界浓度随着其阴离子的感胶离子数的增大而线性增加,同时其对AEO9浊点的改变程度则随着阴离子的感胶离子数的增大而线性下降.     

D5反胶束体系的制备及其增溶特性的研究

以对生态环境友好的D5(十甲基环五硅氧烷)替代传统反胶束体系中的烷烃作为连续相介质,制备新型的D5反胶束体系,并对该体系的增溶行为进行研究,分别比较了阴离子表面活性剂、阳离子表面活性剂、非离子表面活性剂的D5反胶束体系的增溶水量。结果表明,用非极性的D5替代传统反胶束体系中的烷烃来制备对生态环境友好的反胶束体系的方法可行;在某些需要助表面活性剂才能形成的D5反胶束体系里,助表面活性剂醇的用量和表面活性剂的类型及其浓度都影响着体系的增溶水量;非离子表面活性剂形成的TX-10/正辛醇/D5反胶束体系增溶水量最大。     

C12-2-C12·2Br/正庚烷/正己醇体系中临界反胶束浓度的测定

以碘探针光谱法和水增溶法分别测定了季铵盐二聚表面活性剂C_(12)-2C_(12)·2Br在正庚烷/正己醉溶液中的临界反胶束浓度crmc_l和crmc_w,并考察了助表面活性剂—己醇的用量对crmc的影响。。     

表面张力法探究温度对表面活性剂临界胶束浓度的影响

临界胶束浓度是表面活性剂的一个重要性质。本文用表面张力法测定了非离子型表面活性剂的临界胶束浓度。结果表明,随着温度升高,非离子型表面活性剂的临界胶束浓度反而会降低。对温度影响表面活性剂临界胶束浓度的机理进行了初步分析。     

OP-7/氯仿反胶束体系的制备及其增溶水量的研究

以氯仿代替传统的烃类溶剂,制备新型OP-7(非离子表面活性剂)/氯仿反胶束体系,并对该体系的增溶行为进行研究。考察了OP-7的浓度和不同的助表面活性剂对该体系增溶水量的影响及增溶水量与体系的粒径、电导率的关系。结果表明,OP-7的浓度、助表面活性剂醇的种类和用量都影响着体系的增溶水量;同时增溶水量增加,体系的粒径和电导率随之增加,OP-7/正辛醇/氯仿反胶束体系增溶水量最大。     

C_(12)-2-C_(12)·2Br/正庚烷/正己醇体系中临界反胶束浓度的测定

以碘探针光谱法和水增溶法分别测定了季铵盐二聚表面活性剂C_(12)-2C_(12)·2Br在正庚烷/正己醉溶液中的临界反胶束浓度crmc_l和crmc_w,并考察了助表面活性剂—己醇的用量对crmc的影响。。     

Spectroscopic and conductometric studies on the interactions of thionine with anionic and nonionic surfactants

In this study, the interaction of thionine, a cationic dye, with anionic [sodium dodecyl sulphate (SDS), lithium dodecyl sulphate (LiDS), and sodium dodecylbenzene sulphonate (SDBS)], nonionic (Tween 20 and Triton X‐100), and binary mixtures of anionic and nonionic surfactants was studied by conductometric and spectrophotometric measurements. The degree of ionisation, the counterion binding parameters, and the equilibrium constants in the premicellar region were obtained from conductivity data. Binding constants of thionine to anionic, nonionic, and mixtures of anionic and nonionic micelles were determined by spectrophotometric measurements. The binding tendency of thionine to anionic micelles followed the order SDBS > SDS > LiDS. The presence of nonionic surfactants increased significantly the binding affinity of thionine to anionic micelles, and the highest binding constant was calculated in the presence of Tween 20. The results obtained from conductometric studies correlated with those obtained from spectroscopic studies. Data concerning dye–surfactant interaction are important for a fundamental understanding of the performance of single and mixed surfactants and for their industrial application.     

Removal of Ni(II) ions from wastewater by micellar enhanced ultrafiltration using mixed surfactants

Ni(II) ions were removed from aqueous waste using micellar enhanced ultrafiltration (MEUF) with a mixture of surfactants. The surfactant mixture was the nonionic surfactant Tween 80 (TW80) mixed with the anionic surfactant sodium dodecyl sulfate (SDS) in different molar ratios ranging from 0.1–1.5. The operational variables of the MEUF process such as pH, applied pressure, surfactant to metal ion ratio and nonionic to ionic surfactant molar ratio (α) were evaluated. Rejection of Ni and TW80 was 99% and 98% respectively whereas that for SDS was 65%. The flux and all resistances (fouling resistance, resistance due to concentration polarization) were measured and calculated for entire range of α respectively. A calculated flux was found to be declined with time, which was mainly attributed to concentration polarization rather than resistance from membrane fouling.     

Einfluß der kritischen Mizellbildungskonzentration auf die Waschwirkung von Natriumdodecylsulfat

Influence of Critical Micelle Concentration on the Washing Action of Sodium Dodecyl Sulfate The influence of critical micelle concentration of an anionic surfactant on the removal of different types of soils (soot, paraffin oil or mixture of olive oil and oleic acid) from wool was investigated in a model system. The interfacially active single ions and not the micelles are responsible for the removal of soot and oil. At a critical micelle concentration C_k the extent of removal of soot reaches the uppermost limit due to the constant zeta potential of the soot particles attained at C_k. Whereas the non-polar oil is removed by wetting, it is assumed that the higher degree of elution of the polar oil compared to the non-polar one is due to the superimposition of the wetting effect along with the formation of a mixed phase.     

表面活性剂对二氧化硅溶胶稳定性的影响

研究了表面活性剂对二氧化硅溶胶粘度和稳定性的影响.在二氧化硅溶胶中添加不同表面活性剂,测定了该混合体系的粘度变化和稳定性,结果表明阴离子表面活性剂可以降低硅溶胶的粘度,其CMC大约在4.6×10~(-3) mol/L左右,阴离子表面活性剂可以提高硅溶胶稳定性,极值为1.43×10~(-3) mol/L.表面活性剂SDBS对溶胶粘度的影响与其在溶胶颗粒上的包覆有关,SDBS对溶胶的稳定作用是由于SDBS胶束的形成,溶胶颗粒对SDBS的吸附会降低溶胶的稳定性.阴离子和非离子表面活性剂能提高二氧化硅溶胶稳定性,而阳离子表面活性剂会降低溶胶稳定性.     

Surface Properties and Solubility Enhancement of Anionic/Nonionic Surfactant Mixtures Based on Sulfonate Gemini Surfactants

As a class of novel surfactants, Gemini surfactants usually exhibit fairly excellent interfacial properties in aqueous solutions on account of the unique structure. They have significant application and development potential for industrial production. However, the mixing properties of Gemini surfactants with conventional surfactants are the key to their application. The equilibrium surface tension curves of anionic/nonionic surfactant mixtures based on the sulfonate Gemini surfactant (SGS-12) were measured using the Wilhelmy Plate method. The parameters of surface adsorption, the interaction parameters between anionic and nonionic surfactants, and the thermodynamic parameters of micelle formation were calculated from the corresponding equations. In addition, the dynamic surface tension (DST) curves of anionic/nonionic surfactant mixtures were examined through bubble profile analysis, and the diffusion performance parameters were acquired from empirical formulas. The solubilization of pyrene in micelle solutions was studied using UV–vis absorption spectroscopy. The results show that the interaction parameters of all anionic/nonionic surfactants are negative, indicating that there is a synergistic effect on reducing the surface tension. For the SGS-12/OP-10, SGS-12/Tween 80, SGS-12/AEO9, and SGS-12/APG0810 mixtures, the optimum mixing ratios are 6:4, 7:3, 7:3, and 8:2, respectively. The thermodynamic data of micelles show that the formation of mixed micelles for SGS-12/APG0810 mixtures is an enthalpy-driven process. The tendency of DST curves of the SGS-12/APG0810 mixture is similar to that of SGS-12. In comparison with single-surfactant solutions, the anionic/nonionic surfactant mixtures show stronger solubilization capacity toward pyrene.     

混合表面活性剂/乙醇水溶液体系的研究

运用正交试验研究了离子型表面活性剂(SDS)非离子型表面活性剂(Triton)/乙醇三元体系的相互作用,结果表明,体系的表面活性体现在离子型表面活性剂上,醇与非离子型表面活性剂在一定的浓度比上有相互作用。     

Effect of pH on the flotation performance of incinerator fly ash

Flotation was proved to be effective for decarburization and removal of dioxins from hospital solid waste (HSW) incinerator fly ash, but weathering makes it difficult. The effects of three types of surfactants including nonionic (Tween 80), anionic (SDS), and cationic (CTAB) at different pulp pH values on the flotation performance of weathered HSW incinerator fly ash were investigated. Results showed that the corresponding optimal pH values of Tween 80, CTAB, and SDS were 7, 5, and 9 in terms of decarburization performance, respectively, which were validated by the measurement of Zeta potential. The total dioxins and carbon removal efficiencies showed good correlation at various pulp pH values with surfactant of Tween 80. The optimum surfactant type and pH value should be selected as Tween 80 and pH = 7 from the standpoints of the dioxin removal. Under the optimum condition, the lowest content of dioxins (2.7 ng I-TEQ/g) in the tailings was obtained. The content of heavy metals in the froths exhibited higher with addition of SDS compared with that with Tween 80 and CTAB.     

Experimental Study of CMC Evaluation in Single and Mixed Surfactant Systems, Using the UV–Vis Spectroscopic Method

In this study, the critical micellar concentration (CMC) of anionic, cationic and nonionic surfactants was determined using the UV–Vis spectroscopic method. Sodium lauryl sulfate (SDS) as anionic, hexadecyl-trimethyl-ammonium bromide as cationic, tert-octylphenol ethoxylates TOPEON (with N = 9.5, 7.5 and 35) and lauryl alcohol ethoxylate (23EO) as nonionic surfactants have been used. Concentration of surfactants varies both from below and above the CMC value in the pyrene solution. In addition, the amount of the CMC was determined using the values from the data obtained from the graph of absorbance versus concentration of surfactants. A comparative study was conducted between the results of the present study and the literature which shows a good agreement, in particular for TOPEO9.5 and LAEO23. Furthermore, the CMC value of SDS (as an ionic surfactant) in the presence of nonionic surfactants was also examined. The result reveals that with addition of small amount of nonionic surfactant to the anionic SDS surfactant, a decline in the CMC value of the anionic–nonionic system relative to the CMC of pure anionic surfactant was observed. In addition and for the first time, the effect of UV irradiation on the size of the micelle formations was studied. It was found that UV irradiation causes the formation of smaller micelles which is of prime concern in membrane technology.     

Surfactant precipitation in aqueous solutions containing mixtures of anionic and nonionic surfactants

The salinity tolerance (precipitation phase boundary) is measured for a mixed anionic/nonionic surfactant system above the CMC. For any total surfactant concentration, the salinity tolerance is shown to increase as the percentage of nonionic surfactant in the system is increased. A model is developed which can predict the phase boundaries for the mixed surfactant system from the pure anionic surfactant phase boundary and information about mixed micelle formation. In the model, precipitation is viewed as a solubility product relationship between the anionic surfactant monomer and the total unassociated counterion. The reason that salinity tolerance (or counterion concentration necessary to cause precipitation) increases with addition of nonionic surfactant is that mixed micelle formation reduces the anionic surfactant monomer concentration. For the experimental studies, sodium dodecyl sulfate is the anionic surfactant, a polyethoxylated nonylphenol is the nonionic surfactant, and sodium chloride is the added salt.