Preparation, characterization and electrical conductivity studies of NdYb1−xGdxZr2O7 (0 ≤ x ≤ 1.0) ceramics

Several compositions of NdYb_1−xGd_xZr₂O₇ (0 ≤ x ≤ 1.0) ceramics were prepared by pressureless-sintering method at 1973 K for 10 h in air. The relative density, microstructure and electrical conductivity of NdYb_1−xGd_xZr₂O₇ ceramics were analyzed by the Archimedes method, X-ray diffraction, scanning electron microscopy and impedance plots measurements. NdYb_1−xGd_xZr₂O₇ (0 ≤ x ≤ 0.3) ceramics have a single phase of defect fluorite-type structure, and NdYb_1−xGd_xZr₂O₇ (0.7 ≤ x ≤ 1.0) ceramics exhibit a single phase of pyrochlore-type structure; however, the NdYb_0.5Gd_0.5Zr₂O₇ composition shows mixed phases of both defect fluorite-type and pyrochlore-type structures. The measured values of the grain conductivity obey the Arrhenius relation. The grain conductivity of each composition in NdYb_1−xGd_xZr₂O₇ ceramics gradually increases with increasing temperature from 673 to 1173 K. NdYb_1−xGd_xZr₂O₇ ceramics are oxide-ion conductor in the oxygen partial pressure range of 1.0 × 10⁻⁴ to 1.0 atm at all test temperature levels. The highest grain conductivity value obtained in this work is 1.79 × 10⁻² S cm⁻¹ at 1173 K for NdYb_0.3Gd_0.7Zr₂O₇ composition.     

The effect of co-doping with MgO and Yb2O3 on the structure and electrical conductivity of the Sm2Zr2O7 pyrochlore

SmYb_1−xMg_xZr₂O_7−x/2 (0 ≤ x ≤ 0.15) ceramics are pressureless-sintered at 1973 K for 10 h in air. The structure and electrical conductivity of SmYb_1−xMg_xZr₂O_7−x/2 ceramics are investigated by the X-ray diffraction, scanning electron microscopy and impedance spectroscopy measurements. SmYb_1−xMg_xZr₂O_7−x/2 ceramics exhibit a defect fluorite-type structure. The measured electrical conductivities of SmYb_1−xMg_xZr₂O_7−x/2 ceramics obey the Arrhenius relation, and electrical conductivity of each composition increases with increasing temperature from 673 to 1173 K. At identical temperature levels, the electrical conductivity of SmYb_1−xMg_xZr₂O_7−x/2 ceramics gradually increases with increasing magnesia content. SmYb_1−xMg_xZr₂O_7−x/2 ceramics are oxide-ion conductors in the oxygen partial pressure range of 1.0 × 10⁻⁴ to 1.0 atm at all test temperature levels. The electrical conductivity obtained in SmYb_1−xMg_xZr₂O_7−x/2 ceramics reaches the highest value of 2.72 × 10⁻³ S cm⁻¹ at 1173 K for the SmYb_0.85Mg_0.15Zr₂O_6.925 ceramic.     

Studies on electrical properties of La0.8Sr0.2Ga0.8Mg0.2O2.80 (LSGM) and LSGM-SrSn1−xFexO3 (x = 0.8; 0.9) composites and their chemical reactivity

We report the electrical conductivity properties of solid-state synthesized perovskite-like La_0.8Sr_0.2Ga_0.8Mg_0.2O_2.80 (LSGM) and LSGM-SrSn_1−xFe_xO₃ (x = 0.8; 0.9) composites. LSGM exhibits both bulk and grain-boundary contribution in the ac impedance plots. The grain-boundary conductivity (σ_gb) is slightly (≤half-order of magnitude) higher than that of the bulk oxide ion conductivity (σ_bulk). Powder XRD study reveals that no chemical reaction occurs between LSGM and SrSn_1−xFe_xO₃ (1:1 wt.%) at 1000 °C (48 h) and forms a single-phase perovskite-like compound at 1300 °C (48 h) in air, while in hydrogen atmosphere, at 800 °C for 48 h, a growth of LaSrGaO₄ and LaSrGa₃O₇ impurity phases and formation of metallic Fe was observed. The LSGM-SrSn_1−xFe_xO₃ (x = 0.8; 0.9) composites show a single or part of semicircle in air at low-temperature regime. The electrical conductivity of the composites were found to be much higher compared to pure LSGM and lower about an order of magnitude than those of pure Sn-doped SrFeO₃ perovskite.     

Synthesis and characterization of ZnxMg1 − xGa2O4:Co fabricated by low-temperature burning method

A series of Zn_xMg_1 − xGa₂O₄:Co²⁺ spinels (x = 0, 0.25, 0.5, 0.75, and 1.0) was successfully produced through low-temperature burning method by using Mg(NO₃)₂·4H₂O, Zn(NO₃)₂·6H₂O, Ga(NO₃)₃·6H₂O, CO(NH₂)₂, NH₄NO₃, and Co(NO₃)₂·6H₂O as raw materials. The product was characterized by X-ray diffraction, transmission electron microscopy, and photoluminescence spectroscopy. The product was not merely a simple mixture of MgGa₂O₄ and ZnGa₂O₄; rather, it formed a solid solution. The lattice constant of Zn_xMg_1 − xGa₂O₄:Co²⁺ (0 ≤ x ≤ 1.0) crystals has a good linear relationship with the doping density, x. The synthesized products have high crystallinities with neat arrays. Based on an analysis of the form and position of the emission spectrum, the strong emission peak around the visible region (670 nm) can be attributed to the energy level transition [⁴T₁(⁴P) → ⁴A₂(⁴F)] of Co²⁺ in the tetrahedron. The weak emission peak in the near-infrared region can be attributed to the energy level transition [⁴T₁(⁴P) → ⁴T₂(⁴F)] of Co²⁺ in the tetrahedron.     

New binary (1 − x)Ba(Lu1/2Nb1/2)O3-xPbTiO3 solid solution with morphotropic phase boundary

A new ferroelectric solid solution of (1 − x)Ba(Lu_1/2Nb_1/2)O₃-xPbTiO₃ (BLN-PT) (0 ≤ x ≤ 1) has been synthesized by solid state reactions. Its structure and electric properties have been studied by X-ray diffraction and di-/ferro-electric measurements. Based on the investigation, a partial solid state phase diagram of the binary BLN-PT ceramics system has been established, which exhibits a morphotropic phase boundary (MPB) region in the composition range of 0.64 ≤ x ≤ 0.68. The Curie temperature is measured to be around 250 °C in the vicinity of the MPB region, which is much higher than that of PMNT or PZNT system. The dielectric behavior has been discussed based on Curie-Weiss Law and Lorentz-type quadratic relationship. With increasing PT content, a transformation from relaxor to ferroelectric phase has been demonstrated in the solid solution system.     

Study on the rapid synthesis of LiNi1−xCoxO2 cathode material for lithium secondary battery

LiNi_1−xCo_xO₂ (x = 0, 0.1, 0.2) cathode materials were successfully synthesized by a rheological phase reaction method with calcination time of 0.5 h at 800 °C. All obtained powders are pure phase with α-NaFeO₂ structure (R-3m space group). The samples deliver an initial discharge capacity of 182, 199 and 189 mAh g⁻¹ (25 mA g⁻¹, 4.35-3.0 V), respectively. The reaction mechanism was also discussed, which consists of a series of defect reactions. As a result of these defect reactions, the reaction of forming LiNi_1−xCo_xO₂ takes place in high speed.     

Electrochemical and thermal studies of Li[NixLi(1/3−2x/3)Mn(2/3−x/3)]O2 (x = 1/12, 1/4, 5/12, and 1/2)

Samples of the layered cathode materials, Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ (x = 1/12, 1/4, 5/12, and 1/2), were synthesized at 900 °C. Electrodes of these samples were charged in Li-ion coin cells to remove lithium. The charged electrode materials were rinsed to remove the electrolyte salt and then added, along with EC/DEC solvent or 1 M LiPF₆ EC/DEC, to stainless steel accelerating rate calorimetry (ARC) sample holders that were then welded closed. The reactivity of the samples with electrolyte was probed at two states of charge. First, for samples charged to near 4.45 V and second, for samples charged to 4.8 V, corresponding to removal of all mobile lithium from the samples and also concomitant release of oxygen in a plateau near 4.5 V. Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples with x = 1/4, 5/12 and 1/2 charged to 4.45 V do not react appreciably till 190 °C in EC/DEC. Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples charged to 4.8 V versus Li, across the oxygen release plateau, start to significantly react with EC/DEC at about 130 °C. However, their high reactivity is similar to that of Li_0.5CoO₂ (4.2 V) with 1 μm particle size. Therefore, Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples showing specific capacity of up to 225 mAh/g may be acceptable for replacing LiCoO₂ (145 mAh/g to 4.2 V) from a safety point of view, if their particle size is increased.     

Synthesis and tunable thermal expansion properties of Sc2−xYxW3O12 solid solutions

A new series of rare earth solid solutions Sc_2−xY_xW₃O₁₂ was successfully synthesized by the conventional solid-state method. Effects of doping ion yttrium on the crystal structure, morphology and thermal expansion property of as-prepared Sc_2−xY_xW₃O₁₂ ceramics were investigated by X-ray diffraction (XRD), thermogravimetric analysis (TG), field emission scanning electron microscope (FE-SEM) and thermal mechanical analyzer (TMA). Results indicate that the obtained Sc_2−xY_xW₃O₁₂ samples with Y doping of 0≤x≤0.5 are in the form of orthorhombic Sc₂W₃O₁₂-structure and show negative thermal expansion (NTE) from room temperature to 600 °C; while as-synthesized materials with Y doping of 1.5≤x≤2 take hygroscopic Y₂W₃O₁₂·nH₂O-structure at room temperature and exhibit NTE only after losing water molecules. It is suggested that the obvious difference in crystal structure leads to different thermal expansion behaviors in Sc_2−xY_xW₃O₁₂. Thus it is proposed that thermal expansion properties of Sc_2−xY_xW₃O₁₂ can be adjusted by the employment of Y dopant; the obtained Sc_1.5Y_0.5W₃O₁₂ ceramic shows almost zero thermal expansion and its average linear thermal expansion coefficient is −0.00683×10⁻⁶ °C⁻¹ in the 25–250 °C range.     

Evolution of the local structure and electrochemical properties of spinel LiNixMn2−xO4 (0 ≤ x ≤ 0.5)

A series of Ni substituted spinel LiNi_xMn_2−xO₄ (0 ≤ x ≤ 0.5) have been synthesized to study the evolution of the local structure and their electrochemical properties. X-ray diffraction showed a few Ni cations moved to the 8a sites in heavily substituted LiNi_xMn_2−xO₄ (x ≥ 0.3). X-ray photoelectron spectroscopy confirmed Ni²⁺ cations were partially oxidized to Ni³⁺. The local structures of LiNi_xMn_2−xO₄ were studied by analyzing the and A_1g Raman bands. The most compact [Mn(Ni)O₆] octahedron with the highest bond energy of Mn(Ni)O was found for LiNi_0.2Mn_1.8O₄, which showed a Mn(Ni)O average bond length of 1.790 Å, and a force constant of 2.966 N cm⁻¹. Electrolyte decomposition during the electrochemical charging processes increased with Ni substitution. The discharge capacities at the 4.1 and 4.7 V plateaus obeyed the linear relationships with respect to the Ni substitution with the slopes of −1.9 and +1.9, which were smaller than the theoretical values of −2 and +2, respectively. The smaller slopes could be attributed to the electrochemical hysteresis and the presence of Ni³⁺ in the materials.     

The influence of pentavalent Nb substitution for Zr on electrical property of oxide-ion conductor Gd2Zr2O7

Gd₂(Zr_1−xNb_x)₂O_7+x (0 ≤ x ≤ 0.2) ceramics are prepared via the solid state reaction process at 1973 K for 10 h in air. Gd₂(Zr_1−xNb_x)₂O_7+x (x = 0.1, 0.2) ceramics exhibit an ordered pyrochlore-type structure, whereas Gd₂Zr₂O₇ has a defective fluorite-type structure. The electrical property of Gd₂(Zr_1−xNb_x)₂O_7+x ceramics is investigated by electrochemical impedance spectroscopy over a frequency range of 10 Hz to 8 MHz from 623 to 923 K. The electrical conductivity obeys the Arrhenius equation. The grain conductivity of Gd₂(Zr_1−xNb_x)₂O_7+x ceramics varies with doping different Nb contents, and exhibits a maximum at the Nb content of x = 0.1 in the temperature range of 623-923 K. The conductivity in hydrogen atmosphere is a little bit higher than in air in the temperature range of 723-923 K, which indicates that the doping of Zr⁴⁺ by Nb⁵⁺ can increase the proton-type conduction and reduce the oxide-ionic conduction. The conduction of Gd₂(Zr_1−xNb_x)₂O_7+x is not a pure oxide-ionic conductor.     

Synthesis and microstructure of (LaSr)MnO3 and (LaSr)FeO3 ceramics by a reaction-sintering process

(La_xSr_1−x)MnO₃ (LSMO) and (La_xSr_1−x)FeO₃ (LSFO) (x = 0.2–0.4) ceramics prepared by a simple and effective reaction-sintering process were investigated. Without any calcination involved, La₂O₃ and SrCO₃ were mixed with MnO₂ (LSMO) or Fe₂O₃ (LSFO) then pressed and sintered directly. LSMO and LSFO ceramics were obtained after 2 and 4 h sintering at 1350–1400 and 1200–1280 °C, respectively. Grain size decreased as La content increased in LSMO and LSFO ceramics.     

Influence of ytterbium- and samarium-oxides codoping on structure and thermal conductivity of zirconate ceramics

To increase operating temperature and improve performance of gas-turbine engines, it is urgently needed to develop new thermal barrier oxides with a lower thermal conductivity than 6–8 wt.% yttria-stabilized zirconia. (Yb_xSm_1?x)₂Zr₂O₇ (0 ≤ x ≤ 1.0) ceramics were synthesized by pressureless-sintered at 1700 °C for 10 h in air. The relative density, phase structure, morphology and thermal diffusivity coefficients of (Yb_xSm_1?x)₂Zr₂O₇ ceramics were investigated by the Archimedes method, X-ray diffraction, scanning electron microscopy and laser-flash method. Sm₂Zr₂O₇ and (Yb_0.1Sm_0.9)₂Zr₂O₇ ceramics exhibit a pyrochlore structure, while (Yb_xSm_1?x)₂Zr₂O₇ (0.3 ≤ x ≤1.0) ceramics have a defect fluorite-type structure. The thermal conductivities of (Yb_xSm_1?x)₂Zr₂O₇ ceramics first gradually decrease with increasing temperature, and then increase slightly above 800 °C due to the increased radiation contribution. YbSmZr₂O₇ ceramics have the lowest thermal conductivity over the entire temperature range, which is caused by the reduction of cation mean free path in ytterbium–samarium zirconate system.     

Raman and dielectric investigation of (Ba0.9−xSrxCa0.1)(Ti0.8Zr0.2)O3 ferroelectric ceramics

Solid solutions of (Ba_0.9−xSr_xCa_0.1)(Ti_0.8Zr_0.2)O₃ (BSCTZ) (0.1≤x≤0.4) were prepared using the conventional solid state reaction method. The effects of the substitution content on the crystallographic structure, phase transition and dielectric properties of the samples were investigated by dielectric and Raman spectroscopy over a wide temperature range from 100 to 500 K. All the samples were noted to undergo a diffuse phase transition from the tetragonal to the cubic phase and to exhibit a relaxor ferroelectric behavior.     

Zr-doped Li[Ni0.5−xMn0.5−xZr2x]O2 (x = 0, 0.025) as cathode material for lithium ion batteries

Layered Li[Ni_0.5−xMn_0.5−xZr_2x]O₂ (x = 0, 0.025) have been prepared by the mixed hydroxide and molten-salt synthesis method. The individual particles of synthesized materials have a sub-microsize range of 200-500 nm, and LiNi_0.475Mn_0.475Zr_0.05O₂ has a rougher surface than that of LiNi_0.5Mn_0.5O₂. The Li/Li[Ni_0.5−xMn_0.5−xZr_2x]O₂ (x = 0, 0.025) electrodes were cycled between 4.5 and 2.0 V at a current density of 15 mA/g, the discharge capacity of both cells increased during the first ten cycles. The discharge capacity of the Li/LiNi_0.475Mn_0.475Zr_0.05O₂ cell increased from 150 to 220 mAh/g, which is 50 mAh/g larger than that of the Li/LiNi_0.5Mn_0.5O₂ cell. We found that the oxidation of oxygen and the Mn³⁺ ion concerned this phenomenon from the cyclic voltammetry (CV). Thermal stability of the charged Li[Ni_0.5−xMn_0.5−xZr_2x]O₂ (x = 0, 0.025) cathode was improved by Zr doping.     

One-step electrochemical preparation of the ternary (BixSb1−x)2Te3 thin films on Au(1 1 1): Composition-dependent growth and characterization studies

This study reports on the synthesis of ternary semiconductor (Bi_xSb_1−x)₂Te₃ thin films on Au(1 1 1) using a practical electrochemical method, based on the simultaneous underpotential deposition (UPD) of Bi, Sb and Te from the same solution containing Bi³⁺, SbO⁺, and HTeO₂⁺ at a constant potential. The thin films are characterized by X-ray diffraction (XRD), atomic force microscopy (AFM), energy dispersive spectroscopy (EDS) and reflection absorption-FTIR (RA-FTIR) to determine structural, morphological, compositional and optic properties. The ternary thin films of (Bi_xSb_1−x)₂Te₃ with various compositions (0.0 ≤ x ≤ 1.0) are highly crystalline and have a kinetically preferred orientation at (0 1 5) for hexagonal crystal structure. AFM images show uniform morphology with hexagonal-shaped crystals deposited over the entire gold substrate. The structure and composition analyses reveal that the thin films are pure phase with corresponding atomic ratios. The optical studies show that the band gap of (Bi_xSb_1−x)₂Te₃ thin films could be tuned from 0.17 eV to 0.29 eV as a function of composition.     

Preparation of Ni/MgxTi1 − xO catalysts and investigation on their stability in tri-reforming of methane

Ni/Mg_xTi_1 − xO catalysts were prepared through a wet impregnation method by dispersing Ni on Mg_xTi_1 − xO composite oxides obtained via a sol–gel technique. The Ni/Mg_xTi_1 − xO catalysts were characterized by various means including ICP–OES, BET, XRD, H₂–TPR, SEM, and TG. No free NiO peak was found in all XRD patterns of the Ni/Mg_xTi_1 − xO catalysts. The H₂–TPR and chemisorption results indicated that adding Ti to the NiO–MgO system obstructed the formation of solid solution, and thus increased the reducibility of the catalysts. The prepared Mg_xTi_1 − xO composite oxides had the same ability to disperse Ni as TiO₂ and MgO. The tri-reforming (simultaneous oxygen reforming, carbon dioxide reforming, and steam reforming) of methane over Ni/Mg_xTi_1 − xO catalysts was carried out in a fixed bed flow reactor. The conversions of CH₄ and CO₂ can respectively be achieved as high as above 95% and 83% over Ni/Mg_0.75Ti_0.25O catalyst under the reaction conditions. The activity of Ni/Mg_0.75Ti_0.25O and Ni/Mg_0.5Ti_0.5O did not decrease for a reaction period of 50 h, indicating their rather high stability. The experimental results showed that the nature of support, the interaction between metal and support, and the ability to be reduced played an important role in improving the stability of catalysts.     

Coprecipitation synthesis and sintering property of (YbxSm1-x)2Zr2O7 ceramic powders

Abstract

Abstract

(Yb_xSm_1-x)₂Zr₂O₇ (0<x<1·0) ceramic powders were synthesised with chemical coprecipitation and calcination method. Thermal decomposition behaviour of precipitates was studied by differential scanning calorimetry-thermogravimetry. The powders were characterised by X-ray diffractometry, scanning electron microscopy and transmission electron microscopy with energy dispersive spectroscopy. The synthesised powders have a particle size of about 100?nm, and exhibit to a certain extent agglomeration. The sintering behaviour of (Yb_xSm_1-x)₂Zr₂O₇ powders was studied by pressureless sintering method at 1550-1700°C for 10?h in air. The relative densities of (Yb_xSm_1-x)₂Zr₂O₇ ceramics increase with increasing sintering temperature, and reach above 95% when sintered at 1700°C for 10?h in air. Sm₂Zr₂O₇ and (Yb_0·1Sm_0·9)₂Zr₂O₇ ceramics have a pyrochlore structure; however, (Yb_xSm_1-x)₂Zr₂O₇ (0·3<x<1·0) ceramics exhibit a defective fluorite type structure.     

Influence of preparation conditions to structure property, NOx and SO2 sorption behavior of the BaFeO3 − x perovskite catalyst

A series of the BaFeO_3 − x perovskite catalysts was synthesized by a sol-gel method using citric acid and/or EDTA as complexants with a purpose to improve their sulfur-resistance by forming a uniform perovskite structure at a low calcination temperature, i.e. 750 °C. The thermogravimetry results show that almost no carbonate was formed after calcination of the xerogel precursor with the complexants' molar ratio of CA/EDTA ≤ 1.5, which was convinced by the in situ DRIFT spectra results of the Ba-Fe-1 catalyst during the SO₂/O₂ sorption. It indicates that, after adding EDTA into the complexants, the metal ions of the raw material could be mixed homogeneously and react stoichiometrically by calcination at 750 °C to form a uniform perovskite structure. Accordingly, the obtained Ba-Fe-1 perovskite presented a performed sulfur-resistance. Moreover, the seriously damaged structure of the BaFeO_3 − x perovskite by reduction could be in situ regenerated by calcination under lean conditions at 400 °C, which is within the operating temperature zone of the aftertreatment system of diesel to meet the real commercial demands.     

Impact of cobalt substitution for manganese on the structural and electrochemical properties of LiNi0.5Mn0.5O2

A series of LiNi_0.5Mn_0.5−xCo_xO₂ (0 ≤ x ≤ 0.5) compounds was prepared by a solid state reaction, and their structure, surface state and electrochemical characteristics were also investigated by XRD, XPS, EIS and charge-discharge cycling. The non-equivalent substitution of cobalt for manganese induced an increase in the average valence of nickel, thereby shrinking in the lattice volume. Moreover, Co non-equivalent substitution could not only reduce the impurity content but also significantly decreased the charge transfer resistance, thereby improving the rate capabilities.     

Effects of Zn or Ti substitution for Ni on the electrochemical properties of LiNiO2

LiNiO₂ and LiNi_1−yM_yO₂ (M = Zn and Ti, y = 0.005, 0.01, 0.025, 0.05, and 0.1) were synthesized with a solid-state reaction method by calcination at 750 °C for 30 h under oxygen stream after preheating at 450 °C for 5 h in air. LiNi_0.995Zn_0.005O₂ among the Zn-substituted samples and LiNi_0.995Ti_0.005O₂ among the Ti-substituted samples showed the best electrochemical properties. For similar values of y, LiNi_1−yTi_yO₂ had in general better electrochemical properties than LiNi_1−yZn_yO₂. Electrochemical properties seem to be closely related to R-factor but less related to I_0 0 3/I_1 0 4 value. In the FT-IR absorption spectra of LiNiO₂ and LiNi_1−yM_yO₂ (M = Zn and Ti, y = 0.005, 0.01, 0.025, 0.05 and 0.1), Li₂CO₃ was detected even if it is not observed from XRD pattern, with the samples LiNi_1−yZn_yO₂ (y = 0.05 and 0.1) showing Li₂ZnO₂ additionally. The smaller cation mixing of the Ti-substituted samples is considered to lead to their better electrochemical properties than the Zn-substituted samples.