Effect of synthesis condition on the structure and electrochemical properties of Li[Ni1/3Mn1/3Co1/3]O2 prepared by hydroxide co-precipitation method

The layered Li[Ni_1/3Co_1/3Mn_1/3]O₂ powder with good crystalline and spherical shape was prepared by hydroxide co-precipitation method. The effects of pH value, NH₄OH amount, calcination temperature and extra Li amount on the morphology, structure and electrochemical properties of the cathode material were investigated in detail. SEM results indicate that pH value affected both the morphology and the property of the cathode material, and the highest discharge capacity in the first cycle of 163 mAh g⁻¹ (2.8-4.3 V) was obtained at pH value was 12. On the contrary, the NH₄OH amount, which was used as a chelating agent, only affected the particle size distribution of the material. The calcination temperatures caused great difference in the structure and property of layered Li[Ni_1/3Co_1/3Mn_1/3]O₂, and the best electrochemical properties were obtained at the calcination temperature of 800 °C. Extra Li amount not only caused difference in the material structure, but also affected their electrochemical properties. With increasing Li amount, the lattice parameters (a and c) increased monotonously, and the highest first cycle coulombic efficiency (the ratio of discharge capacity to charge capacity in the first cycle) was obtained with the Li/M of 1.10. Therefore, the optimum synthetic conditions for the hydroxide co-precipitation reaction were: pH value was 12, NH₄OH amount was 0.36 mol L⁻¹, calcination temperature was 800 °C and the Li/M molar ratio was 1.10.     

Synthesis and electrochemical properties of submicron LiNi0.8Co0.2O2 by a polymer-pyrolysis method

A polymer-pyrolysis method was used to synthesize LiNi_0.8Co_0.2O₂, which has potential application in lithium ion batteries. The effect of calcination temperature and time on the structure and electrochemical performance of the material was investigated. XRD analysis showed that the powders obtained by calcination at 750 °C for 3 h had the best-ordered hexagonal layer structure. SEM image showed these powders were fine, narrowly distributed with platelet morphology. The charge-discharge tests demonstrated these powders had the best electrochemical properties, with an initial discharge capacity of 189 mAh/g and capacity retention of 95.2% after 50 cycles when cycled at 50 mA/g between 3.0 and 4.3 V. Besides, these powders also had exhibited excellent rate capability.     

Synthetic optimization of spherical Li[Ni1/3Mn1/3Co1/3]O2 prepared by a carbonate co-precipitation method

A carbonate co-precipitation method was employed to prepare spherical Li[Ni_1/3Co_1/3Mn_1/3]O₂ cathode material. The precursor, [Ni_1/3Co_1/3Mn_1/3]CO₃, was prepared using ammonia as chelating agent under CO₂ atmosphere. The spherical Li[Ni_1/3Co_1/3Mn_1/3]O₂ was prepared by mixing the precalcined [Ni_1/3Co_1/3Mn_1/3]CO₃ with LiOH followed by high temperature calcination. The preparation conditions such as ammonia concentration, co-precipitation temperature, calcination temperature and Li/[Ni_1/3Co_1/3Mn_1/3] ratio were varied to optimize the physical and electrochemical properties of the prepared Li[Ni_1/3Co_1/3Mn_1/3]O₂. The structural, morphological, and electrochemical properties of the prepared LiNi_1/3Co_1/3Mn_1/3O₂ were characterized by XRD, SEM, and galvanostatic charge-discharge cycling. The optimized material has a spherical particle shape and a well ordered layered structure, and it also has an initial discharge capacity of 162.7 mAh g^− 1 in a voltage range of 2.8-4.3 V and a capacity retention of 94.8% after a hundred cycles. The optimized ammonia concentration, co-precipitation temperature, calcination temperature, and Li/[Ni_1/3Co_1/3Mn_1/3] ratio are 0.3 mol L^− 1, 60 °C, 850 °C, and 1.10, respectively.     

Fabrication of three-dimensional porous structured Co3O4 and its application in lithium-ion batteries

A novel three-dimensional (3D) porous structured Co₃O₄ was prepared by electrodeposition combined with thermal-treatment method. The electrochemical properties of as-prepared 3D porous Co₃O₄ were closely related to its morphology and structure which can be modified by various thermal-treatment temperatures. The 3D porous Co₃O₄ prepared at 300 °C exhibited smaller crystallite size and higher capacity compared to 400 °C as well as 500 °C. As used in lithium-ion batteries, the porous Co₃O₄ anodes delivered a high reversible capacity of about 1100 mAh g⁻¹ with no obvious capacity fading up to 50 cycles and exhibited higher rate capability compared with Co₃O₄ foil anodes. The enhanced electrochemical performances of 3D porous Co₃O₄ anodes are attributed to its unique 3D porous structure which can offer a large materials/electrolyte contact area and accommodate the strain induced by the volume change during cycling.     

LiNi1/3Mn1/3Co1/3O2 synthesized by the Pechini method for the positive electrode in Li-ion batteries: Material characteristics and electrochemical behaviour

The feasibility of the Pechini method for the preparation of LiNi_1/3Mn_1/3Co_1/3O₂ with characteristics appropriate for Li-ion battery positive electrodes was investigated. The method involves formation of one single chemically homogenous precursor material and thus permits reduced calcination times and minimal lithium evaporation. The physical and electrochemical properties of the materials were investigated with variation in final calcination temperature. Chemical analysis showed that the materials could be prepared with high crystallinity and yet little or no loss of lithium. The material calcined at 1000 °C showed the highest specific capacity—180 mAh g⁻¹ when cycled between 4.5 and 3 V, and it maintained its capacity over 50 cycles. The advantage of this material over those prepared at 800 and 900 °C can probably be attributed to the fact that the degree of crystallinity, crystallite size and size of the primary particles increase with calcination temperature, and that the powder attains a more suitable morphology which promotes electronic connectivity to all of the oxide material. A temperature above 1000 °C should however not be used as indicated by an abrupt change in lattice parameters and decrease in electronic conductivity when going from 1000 to 1050 °C. The Pechini method presents an attractive option for the preparation of LiNi_1/3Mn_1/3Co_1/3O₂ positive electrode material.     

Effect of synthesis condition on the structural and electrochemical properties of Li[Ni1/3Mn1/3Co1/3]O2 prepared by the metal acetates decomposition method

In order to get homogeneous layered oxide Li[Ni_1/3Mn_1/3Co_1/3]O₂ as a lithium insertion positive electrode material, we applied the metal acetates decomposition method. The oxide compounds were calcined at various temperatures, which results in greater difference in morphological (shape, particle size and specific surface area) and the electrochemical (first charge profile, reversible capacity and rate capability) differences. The Li[Ni_1/3Mn_1/3Co_1/3]O₂ powders were characterized by means of X-ray diffraction (XRD), charge/discharge cycling, cyclic voltammetry and SEM. XRD experiment revealed that the layered Li[Ni_1/3Mn_1/3Co_1/3]O₂ material can be best synthesized at temperature of 800 °C. In that synthesized temperature, the sample showed high discharge capacity of 190 mAh g⁻¹ as well as stable cycling performance at a current density of 0.2 mA cm⁻² in the voltage range 2.3-4.6 V. The reversible capacity after 100 cycles is more than 190 mAh g⁻¹ at room temperature.     

Hydrothermal synthesis of Co3O4 microspheres as anode material for lithium-ion batteries

Co₃O₄ microspheres were synthesized in mass production by a simple hydrothermal treatment. One micrometer-sized spherical particles with well-crystallization could be obtained by XRD and SEM. Higher specific surface area (93.4 m² g⁻¹) and larger pore volume (78.4 cm³ g⁻¹) by BET measurements offered more interfacial bondings for extra sites of Li⁺ insertion, which resulted in the anomalous large initial irreversible capacity and capacity cycling loss due to SEI film formation. The capacity retention of Co₃O₄ microspheres involved first forming acted as Li-ion anode material is almost above 90% from 12th cycle and it retain lithium storage capacity of 550.2 mAh g⁻¹ after 25 cycles, which show good long-life stability. The electrochemical impedance spectroscopy (EIS) tests before and after cyclic voltammetry measurements and charge-discharge experiments were carried out and the corresponding D_Li values were also calculated. The relationship of the ac impedance spectra and the cycling behaviors was discussed. It is found that the decrease of capacity results from the larger Li⁺ charge-transfer impedance and the lower lithium-diffusion processes on cycling, which is in very good agreement with the electrochemical behaviors of Co₃O₄ electrode.     

Preparation and electrochemical capacitance of cobalt oxide (Co3O4) nanotubes as supercapacitor material

Cobalt oxide (Co₃O₄) nanotubes have been successfully synthesized by chemically depositing cobalt hydroxide in anodic aluminum oxide (AAO) templates and thermally annealing at 500 °C. The synthesized nanotubes have been characterized by scanning electron microscope (SEM), transmission electron microscope (TEM) and X-ray diffraction (XRD). The electrochemical capacitance behavior of the Co₃O₄ nanotubes electrode was investigated by cyclic voltammetry, galvanostatic charge-discharge studies and electrochemical impedance spectroscopy in 6 mol L⁻¹ KOH solution. The electrochemical data demonstrate that the Co₃O₄ nanotubes display good capacitive behavior with a specific capacitance of 574 F g⁻¹ at a current density of 0.1 A g⁻¹ and a good specific capacitance retention of ca. 95% after 1000 continuous charge-discharge cycles, indicating that the Co₃O₄ nanotubes can be promising electroactive materials for supercapacitor.     

Structural and electrical properties of La0.7Sr0.3Co0.5Fe0.5O3 powders synthesized by solid state reaction

This work investigates the effect of synthesis parameters (calcination temperature, milling conditions and sintering temperature) on the structural, morphological and electrical properties of La_0.7Sr_0.3Co_0.5Fe_0.5O₃ (LSCF) powders prepared by the solid state reaction. The thermogravimetric profile showed that the minimum temperature needed for the carbonate decomposition and formation of perovskite phase is 800 °C. SEM analysis revealed the loose and porous structure of the powder materials. The XRD patterns demonstrate that milling parameters such as grinding balls:sample ratio, rotational speed, and milling time influence the structural properties. The results revealed that powders synthesized with grinding balls:sample ratio of 8:1, 500 rpm and 4 h of milling present pure LSCF phase. Porosity of the pellets decreased with increasing sintering temperature from 950 to 1100 °C. Electrical conductivity was measured at 400–1000 °C and correlated with sintering temperature.     

Textural and capacitive characteristics of MnO2 nanocrystals derived from a novel solid-reaction route

Nanostructured manganese dioxide (MnO₂) materials were synthesized via a novel room-temperature solid-reaction route starting with Mn(OAc)₂·4H₂O and (NH₄)₂C₂O₄·H₂O raw materials. In brief, the various MnO₂ materials were obtained by air-calcination (oxidation decomposition) of the MnC₂O₄ precursor at different temperatures followed by acid-treatment in 2 M H₂SO₄ solution. The influence of calcination temperature on the structural characteristics and capacitive properties in 1 M LiOH electrolyte of the MnO₂ materials were investigated by X-ray diffraction (XRD), infrared spectrum (IR), transmission electron microscope (TEM) and Brunauer-Emmett-Teller (BET) surface area analysis, cyclic voltammetry, ac impedance and galvanostatic charge/discharge electrochemical methods. Experimental results showed that calcination temperature has a significant influence on the textural and capacitive characteristics of the products. The MnO₂ material obtained at the calcination temperature of 300 °C followed by acid-treatment belongs to nano-scale column-like (or needle-like) γ,α-type MnO₂ mischcrystals. While, the MnO₂ materials obtained at the calcination temperatures of 400, 500, and 600 °C followed by acid-treatment, respectively, belong to γ-type MnO₂ with the morphology of aggregates of crystallites. The γ,α-MnO₂ derived from calcination temperature of 300 °C exhibited a initial specific capacitance lower than that of the γ-MnO₂ derived from the elevated temperatures, but presented a better high-rate charge/discharge cyclability.     

Storage behavior of LiNi1/3Co1/3Mn1/3O2/artificial graphite Li-ion cells

A series of Li-ion cells containing LiNi_1/3Co_1/3Mn_1/3O₂ and artificial graphite as the active materials, have been stored at various temperatures from 0 to 70 °C. The 3-electrode impedance study shows that both the solid electrolyte interphase (SEI) film resistance and charge-transfer resistance of the negative electrode first decrease and then increase during storage at 70 °C, while both resistances for the positive electrode increase under this condition. The reversible capacity loss of the 3-electrode cell, which is possibly attributed to dissolution of SEI film, accounts for over half of the total capacity loss after 5 weeks of storage. Gases generated from the swelling aged cell at 60 °C are mainly attributed to the reduction of the electrolyte on the negative electrode. A further study on the side-reaction has been done on graphite electrodes and separators, indicating that SEI films may be rearranged and reformed on negative electrodes, and that some pores on the positive electrode side of separator are blocked due to the oxidation of electrolyte, resulting in poor Li-ion transfer and rise of the ohmic resistance during storage at elevated temperature. However, at 0 °C, this side-reaction is impeded.     

Porous Co3O4 nanoplatelets by self-supported formation as electrode material for lithium-ion batteries

In this paper, we have reported a simple and rapid approach for the large-scale synthesis of β-Co(OH)₂ nanoplatelets via the microwave hydrothermal process using potassium hydroxide as mineralizer at 140 °C for 3 h. Calcining the β-Co(OH)₂ nanoplatelets at 350 °C for 2 h, porous Co₃O₄ nanoplatelets with a 3D quasi-single-crystal framework were obtained. The process of converting the β-Co(OH)₂ nanoplatelets into the Co₃O₄ nanoplatelets is a self-supported topotactic transformation, which is easily controlled by varying the calcining temperature. The textural characteristics of Co₃O₄ products have strong positive effects on their electrochemical properties as electrode materials in lithium-ion batteries. The obtained porous Co₃O₄ nanoplatelets exhibit a low initial irreversible loss (18.1%), ultrahigh capacity, and excellent cyclability. For example, a reversible capacity of 900 mAh g⁻¹ can be maintained after 100 cycles.     

Synthesis and electrochemical characterization of nano-CeO2-coated nanostructure LiMn2O4 cathode materials for rechargeable lithium batteries

LiMn₂O₄ spinel cathode materials were coated with 0.5, 1.0, and 1.5 wt.% CeO₂ by a polymeric process, followed by calcination at 850 °C for 6 h in air. The surface-coated LiMn₂O₄ cathode materials were physically characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray photoelectron microscopy (XPS). XRD patterns of CeO₂-coated LiMn₂O₄ revealed that the coating did not affect the crystal structure or the Fd3m space group of the cathode materials compared to uncoated LiMn₂O₄. The surface morphology and particle agglomeration were investigated using SEM, TEM image showed a compact coating layer on the surface of the core materials that had average thickness of about 20 nm. The XPS data illustrated that the CeO₂ completely coated the surface of the LiMn₂O₄ core cathode materials. The galvanostatic charge and discharge of the uncoated and CeO₂-coated LiMn₂O₄ cathode materials were measured in the potential range of 3.0-4.5 V (0.5 C rate) at 30 °C and 60 °C. Among them, the 1.0 wt.% of CeO₂-coated spinel LiMn₂O₄ cathode satisfies the structural stability, high reversible capacity and excellent electrochemical performances of rechargeable lithium batteries.     

Spray-drying synthesized LiNi0.6Co0.2Mn0.2O2 and its electrochemical performance as cathode materials for lithium ion batteries

Layered LiNi_0.6Co_0.2Mn_0.2O₂ materials were synthesized at different sintering temperatures using spray-drying precursor with molar ratio of Li/Me = 1.04 (Me = transition metals). The influences of sintering temperature on crystal structure, morphology and electrochemical performance of LiNi_0.6Co_0.2Mn_0.2O₂ materials have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and charge-discharge test. As a result, material synthesized at 850 °C has excellent electrochemical performance, delivering an initial discharge capacity of 173.1 mAh g^− 1 between 2.8 and 4.3 V at a current density of 16 mA g^− 1 and exhibiting good cycling performance.     

Synthesis of LiNi1/3Co1/3Mn1/3O2 cathode materials by using a supercritical water method in a batch reactor

LiNi_1/3Co_1/3Mn_1/3O₂ and LiCoO₂ cathode materials were synthesized by using a supercritical water (SCW) method with a metal salt solution in a batch reactor. Stoichiometric LiNi_1/3Co_1/3Mn_1/3O₂ was successfully synthesized in a 10-min reaction without calcination, while overlithiated LiCoO₂ (Li_1.15CoO₂) was synthesized using the batch SCW method. The physical properties and electrochemical performances of LiNi_1/3Co_1/3Mn_1/3O₂ were compared to those of Li_1.15CoO₂ by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), and charge/discharge cycling tests. The XRD pattern of LiNi_1/3Co_1/3Mn_1/3O₂ was found to be similar to that of Li_1.15CoO₂, showing clear splitting of the (0 0 6)/(1 0 2) and (1 0 8)/(1 1 0) peak pairs as particular characteristics of the layered structure. In addition, both cathode powders showed good crystallinity and phase purity, even though a short reaction time without calcination was applied to the SCW method. The initial specific discharge capacities of the Li_1.15CoO₂ and LiNi_1/3Co_1/3Mn_1/3O₂ powders at a current density of 0.24 mA/cm² in 2.5-4.5 V were 149 and 180 mAh/g, and their irreversible capacity loss was 20 and 17 mAh/g, respectively. The discharge capacities of the Li_1.15CoO₂ and LiNi_1/3Co_1/3Mn_1/3O₂ powders decreased with cycling and remained at 108 and 154 mAh/g after 30 cycles, which are 79% and 89% of the initial capacities. Compared to the overlithiated LiCoO₂ cathode powders, the LiNi_1/3Co_1/3Mn_1/3O₂ cathode powders synthesized by SCW method had better electrochemical performances.     

Formation of LiNi0.5Co0.5VO4 nano-crystals by solvothermal reaction

LiNi_0.5Co_0.5VO₄ nano-crystals were solvothermally prepared using a mixture of LiOH·H₂O, Ni(NO₃)₂·6H₂O, Co(NO₃)₂·6H₂O and NH₄VO₃ in isopropanol at 150–200 °C followed by 300–600 °C calcination to form powders. TGA curves of the solvothermal products show weight losses due to evaporation and decomposition processes. The purified products seem to form at 500 °C and above. The products analyzed by XRD, selected area electron diffraction (SAED), energy dispersive X-ray (EDX) and atomic absorption spectrophotometer (AAS) correspond to LiNi_0.5Co_0.5VO₄. V–O stretching vibrations of VO₄ tetrahedrons analyzed using FTIR and Raman spectrometer are in the range of 620–900 cm⁻¹. A solvothermal reaction at 150 °C for 10 h followed by calcination at 600 °C for 6 h yields crystals with lattice parameter of 0.8252 ± 0.0008 nm. Transmission electron microscope (TEM) images clearly show that the solvothermal temperatures play a more important role in the size formation than the reaction times.     

Synthesis and characterization of Al2O3 nanopowders by a simple chitosan-polymer complex solution route

Al₂O₃ nanopowders were synthesized by a simple chitosan-polymer complex solution route. The precursors were calcined at 800–1200 °C for 2 h in air. The prepared samples were characterized by XRD, FTIR and TEM. The results showed that for the precursors prepared with pH 3–9 γ-Al₂O₃ and δ-Al₂O₃ are the two main phases formed after calcination at 800–1000 °C. Interestingly, when the precursor prepared with pH 2 was used, α-Al₂O₃ was formed after calcination at 1000 °C, and pure α-Al₂O₃ was obtained after calcination at 1200 °C. The crystallite sizes of the prepared powders were found to be in the range of 4–49 nm, as evaluated by the XRD line broadening method. TEM investigation revealed that the Al₂O₃ nanopowders consisted of rod-like shaped particles and nanospheres with particle sizes in the range of 10–300 nm. The corresponding selected-area electron diffraction (SAED) analysis confirmed the formation of γ- and α-Al₂O₃ phases in the samples.     

Rapid microwave-assisted synthesis of graphene nanosheet/Co3O4 composite for supercapacitors

Graphene nanosheet (GNS)/Co₃O₄ composite has been rapidly synthesized by microwave-assisted method. Field emission scanning electron microscopy and transmission electron microscopy observation reveals the homogeneous distribution of Co₃O₄ nanoparticles (3-5 nm in size) on graphene sheets. Electrochemical properties are characterized by cyclic voltammetry, galvanostatic charge/discharge and electrochemical impedance spectroscopy. A maximum specific capacitance of 243.2 F g⁻¹ has been obtained at a scan rate of 10 mV s⁻¹ in 6 M KOH aqueous solution for GNS/Co₃O₄ composite. Furthermore, the composite exhibits excellent long cycle life along with ∼95.6% specific capacitance retained after 2000 cycle tests.     

Effect of fluoroethylene carbonate on high temperature capacity retention of LiMn2O4/graphite Li-ion cells

In order to overcome severe capacity fading of LiMn₂O₄/graphite Li-ion cells at high temperature at 60 °C, fluoroethylene carbonate (FEC) was newly evaluated as an electrolyte additive. With 2 wt.% FEC addition into the electrolyte (EC/DEC/PC with 1 M LiPF₆), the capacity retention at 60 °C after 130 cycles was significantly improved by about 20%. To understand the underlying principle on the capacity retention enhancement, the electrochemical properties of the cells including cell performance, impedance behavior as well as the characteristics of the interfacial properties were examined. Based on these results, it is suggested that the improved capacity retention of LiMn₂O₄/graphite Li-ion cells with addition of FEC especially at high temperature is mainly originated from the thin and stable SEI layer formed on the graphite anode surface.     

Low-temperature solution combustion synthesis of high performance LiNi0.5Mn1.5O4

High-voltage LiNi_0.5Mn_1.5O₄ spinels were synthesized by a low temperature solution combustion method at 400 °C, 600 °C and 800 °C for 3 h. The phase composition, structural disordering, micro-morphologies and electrochemical properties of the products were investigated by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscope (SEM) and constant current charge–discharge test. XRD analysis indicated that single phase LiNi_0.5Mn_1.5O₄ powders with disordered Fd-3m structures were obtained by the method at 400 °C, 600 °C and 800 °C. The crystallinity increased with increasing preparation temperatures. XRD and FTIR data indicated that the degree of structural disordering in the product prepared at 800 °C was the largest and in the product prepared at 600 °C was the least. SEM investigation demonstrated that the particle size and the crystal perfection of the products were increased with increasing temperatures. The particles of the product prepared at 600 °C with ~200 nm in size are well developed and homogeneously distributed. Charge/discharge curves and cycling performance tests at different current density indicated that the product prepared at 600 °C had the largest specific capacity and the best cycling performance, due to its high purity, high crystallinity, small particle size as well as moderate amount of Mn³⁺ ions.