The LixMPn4 phases (M/Pn = Ti/P, V/As): new negative electrode materials for lithium ion rechargeable batteries

Li_xTiP₄ ternary phases (x=7 and 9) show very close electrochemical behaviors versus lithium compared to the previously reported Li₉VAs₄ and Li₇VP₄. Up to seven lithium ions reversibly react with Li₉TiP₄, leading to specific and volumetric capacities of 970 mAh/g and 1650 mAh/cm³, respectively, at average potentials close to 1 V. Galvanostatic and potentiodynamic experiments reveal that lithium extraction/insertion follow different mechanisms: a two-phase process is evidenced on charge whereas a more complex process is achieved on discharge. Besides, in situ X-ray diffraction (XRD) patterns show that both Li₉TiP₄ and Li₉VAs₄ undergo a reversible crystalline to amorphous structural phase transition upon cycling.     

Low temperature solid-state synthesis routine and mechanism for Li3V2(PO4)3 using LiF as lithium precursor

Monoclinic lithium vanadium phosphate, Li₃V₂(PO₄)₃, has been successfully synthesized using LiF as lithium source. The one-step reaction with stoichiometric composition and relative lower sintering temperature (700 °C) has been used in our experimental processes. The solid-state reaction mechanism using LiF as lithium precursor has been studied by X-ray diffraction and Fourier transform infrared spectra. The Rietveld refinement results show that in our product sintered at 700 °C no impurity phases of VPO₄, Li₅V(PO₄)₂F₂, or LiVPO₄F can be detected. The solid-state reaction using Li₂CO₃ as Li-precursor has also been carried out for comparison. X-ray diffraction patterns indicate that impurities as Li₃PO₄ can be found in the product using Li₂CO₃ as Li-precursor unless the sintering temperatures are higher than 850 °C. An abrupt particle growth (about 2 μm) has also been observed by scanning electron microscope for the samples sintered at higher temperatures, which can result in a poor cycle performance. The product obtained using LiF as Li-precursor with the uniform flake-like particles and smaller particle size (about 300 nm) exhibits the better performance. At the 50th cycle, the reversible specific capacities for Li₃V₂(PO₄)₃ measured between 3 and 4.8 V at 1C rate are found to approach 147.1 mAh/g (93.8% of initial capacity). The specific capacity of 123.6 mAh/g can even be hold between 3 and 4.8 V at 5C rate.     

A novel lithium intercalation compound based on the layered structure of lithium nitridonickelates Li3−2xNixN

New lithium nickel nitrides Li_3−2xNi_xN (0.20 ≤ x ≤ 0.60) have been prepared and investigated as negative electrode in the 0.85/0.02 V potential window. These materials are prepared from a Ni/Li₃N mixture at 700 °C under a nitrogen flow. Their structural characteristics as well as their electrochemical behaviour are investigated as a function of the nickel content. For the first time are reported here the electrochemical properties of a lithium intercalation compound based on a layered nitride structure. The Li_3−2xNi_xN compounds can be reversibly reduced and oxidized around 0.5 V versus Li/Li⁺ leading to specific capacities in the range 120-160 mAh/g depending on the nickel content and the C rate. Due to a large number of lithium vacancies, the structural stability provides an excellent capacity retention of the specific capacity upon cycling.     

Li6V10O28, a novel cathode material for Li-ion battery

A novel cathode material, lithium decavanadate Li₆V₁₀O₂₈ with a large tunnel within the framework structure for lithium ion battery has been prepared by hydrothermal synthesis and annealing dehydration treatment. The structure and electrochemical properties of the sample have been investigated. The novel material shows good reversibility for Li⁺ insertion/extraction and long cycle life. High discharge capacity (132 mAh/g) is obtained at 0.2 mA/cm² discharge current and potential range between 2.0 and 4.2 V versus Li⁺/Li. AC impedance of the Li/Li₆V₁₀O₂₈ cell reveals that the cathode process is controlled mainly by Li⁺ diffusion in the active material. The novel material would be a promising cathode material for Li-ion batteries.     

Effect of K2O on structure-property relationships and phase transformations in Li2O-SiO2 glasses

Glass compositions with formula (71.78 − x)SiO₂-2.63Al₂O₃-(2.63 + x)K₂O-23.7Li₂O (mol.%, x = 0-10) and SiO₂/Li₂O molar ratios far beyond that of stoichiometric lithium disilicate (Li₂Si₂O₅) were prepared by conventional melt-quenching technique to investigate the influence of K₂O content on structural transformations and devitrification behaviour of glasses in the Li₂O-SiO₂ system. The scanning electron microscopy (SEM) examination of as cast non-annealed glasses revealed the presence of nanosized droplets in glassy matrices suggesting occurrence of liquid-liquid phase separation. An overall trend towards depolymerization of the silicate glass network with increasing K₂O content was demonstrated by employing magic angle spinning-nuclear magnetic resonance (MAS-NMR) spectroscopy. The distribution of structural units in the experimental glasses was estimated using ²⁹Si MAS-NMR spectroscopy suggesting the appearance of Q², enhancement of Q³ and diminishing of Q⁴ groups with increasing K₂O contents. X-ray diffraction (XRD) and differential thermal analysis (DTA) were used to assess the influence of K₂O on devitrification process and formation of lithium disilicate (Li₂Si₂O₅) and/or lithium metasilicate (Li₂SiO₃) crystalline phases.     

Synthesis of hollandite-type LixMnO2 by Li ion-exchange in molten salt and lithium insertion characteristics

The Li⁺ ion-exchange reaction of K⁺-type α-K_0.14MnO_1.93·nH₂O containing different amounts of water molecules (n = 0-0.15) with a large (2 × 2) tunnel structure has been investigated in a LiNO₃-LiCl molten salt at 300 °C. The Li⁺ ion-exchanged products were examined by chemical analysis, X-ray diffraction, and transmission electron microscopy measurements. The K⁺ ions and the hydrogens of the water molecules in the (2 × 2) tunnels of α-MnO₂ were exchanged by Li⁺ ions in the molten salt, resulting in the Li⁺-type α-MnO₂ containing different amounts of Li⁺ ions and lithium oxide (Li₂O) in the (2 × 2) tunnels with maintaining the original hollandite structure.The electrochemical properties and structural variation with initial discharge and charge-discharge cycling of the Li⁺ ion-exchanged α-MnO₂ samples have been investigated as insertion compounds in the search for new cathode materials for rechargeable lithium batteries. The Li⁺ ion-exchanged α-MnO₂ samples provided higher capacities and higher Li⁺ ion diffusivity than the parent K⁺-type materials on initial discharge and charge-discharge cyclings, probably due to the structural stabilization with the existence of Li₂O in the (2 × 2) tunnels.     

Electrochemical behavior of lithium intercalated in a molybdenum disulfide-crown ether nanocomposite

A new nanocomposite, obtained from the intercalation of the cyclic ether 12-Crown-4 into MoS₂, Li_0.32MoS₂(12-Crown-4)_0.19, is described. The laminar product has an interlaminar distance of 14.4 Å. The electrical conductivity of the nanocomposite varies from 2.5 × 10⁻² to 4.3 × 10⁻² S cm⁻¹ in the range 25-77 °C, being about four times higher than the analogous poly(ethylene oxide) (PEO) derivative at room temperature. The electrochemical step-wise galvanostatic intercalation or de-intercalation of lithium, leading to Li_xMoS₂(12-Crown-4)_0.19 with x in the range 0.07-1.0, indicates a Li/Li⁺ pair average potential of 2.8 V. The electrochemical lithium diffusion coefficients in the crown ether intercalates, determined by galvanostatic pulse relaxation between 15 and 37 °C at different lithium intercalation degrees, are higher than those of the PEO derivatives under similar conditions, being however the diffusion mechanism rather more complex. The variation of both, the lithium diffusion activation enthalpy and the quasi-equilibrium potentials, with the lithium content shows there are two different limit behaviors, at low and high lithium intercalation degree, respectively. These features are discussed by considering the high stability of the Li-crown ether complex and the different chemical environments found by lithium along the intercalation process.     

Potentiometric measurements and impedance characteristics of Li0.30La0.57TiO3 membrane in lithium anhydrous solutions

The potentiometric response of the Li⁺ ion-selective electrode based on the fast ion conductor Li_3xLa_2/3−xTiO₃ (x = 0.10) membrane (named LLTO) as well as the impedance of the LLTO membrane/Li⁺ solution in either anhydrous or hydrated PC solvent have been carried out. A four-electrode configuration has been used for the investigation of the interfacial phenomenon. It has been shown that the LLTO membrane can be used to detect the Li⁺ activity in anhydrous solutions through a Li⁺ ion exchange mechanism. The potentiometric response shows a Nernstian behavior with a Li⁺ sensitivity of −72 mV/decade at 25 °C. This high sensitivity can be correlated to a localised hydroxylation of the oxide surface with the residual water present in the solution in combination to the Li⁺ exchange reaction. An apparent standard current density of 12 μA/cm² and a charge-transfer coefficient of 0.29 have been determined. However, as water content in the electrolyte increases, the activity domain of the detection decreases to lead to the disappearance of the Li⁺ ion exchange mechanism in Li⁺ aqueous solution. This annihilation of the exchange process may be due to the predominant catalytic reaction of [Ti-O]⁻ with H₂O and/or to the formation of a water layer on the oxide surface.     

A novel layered Li [Li0.12NizMg0.32−zMn0.56]O2 cathode material for lithium-ion batteries

Layered Li[Li_0.12Ni_zMg_0.32−zMn_0.56]O₂ oxide cathodes containing lithium atoms in the transition metal layers were synthesized and characterized using X-ray diffraction (XRD), galvanostatic cycling, and differential scanning calorimetry (DSC). The Li[Li_0.12Ni_zMg_0.32−zMn_0.56]O₂ cathodes deliver a specific discharge capacity of about 190 mAh/g at room temperature and 236 mAh/g at 55 °C when cycled between 2.7 and 4.6 V versus Li/Li⁺. Excellent capacity retention and smooth potential profiles at room and elevated temperatures over extended cycles suggest that this material does not convert into a spinel structure.     

Co-precipitation synthesis of spherical Li1.05M0.05Mn1.9O4 (M = Ni, Mg, Al) spinel and its application for lithium secondary battery cathode

Metal-doped spinel lithium manganese oxides were successfully synthesized via co-precipitation. The synthesized Li_1.05M_0.05Mn_1.9O₄ (M = Ni, Mg, Al) had highly crystalline cubic spinel phase with the space group Fd3m, as confirmed by X-ray diffraction study. From scanning electron microscopic observation, it was found that the prepared materials had spherical morphology with high tap-density. The Li_1.05M_0.05Mn_1.9O₄ (M = Ni, Mg, Al) electrode exhibited improved cycling performance at elevated temperature. Especially, the Li_1.05Al_0.05Mn_1.9O₄ showed capacity retention of 91.5% during 100 cycles at elevated temperature (55 °C). Also the thermal stability of the Li_1.05M_0.05Mn_1.9O₄ (M = Ni, Mg, Al) was also significantly improved.     

High performance Li3V2(PO4)3/C composite cathode material for lithium ion batteries studied in pilot scale test

Li₃V₂(PO₄)₃/C composite cathode material was synthesized via carbothermal reduction process in a pilot scale production test using battery grade raw materials with the aim of studying the feasibility for their practical applications. XRD, FT-IR, XPS, CV, EIS and battery charge-discharge tests were used to characterize the as-prepared material. The XRD and FT-IR data suggested that the as-prepared Li₃V₂(PO₄)₃/C material exhibits an orderly monoclinic structure based on the connectivity of PO₄ tetrahedra and VO₆ octahedra. Half cell tests indicated that an excellent high-rate cyclic performance was achieved on the Li₃V₂(PO₄)₃/C cathodes in the voltage range of 3.0-4.3 V, retaining a capacity of 95% (96 mAh/g) after 100 cycles at 20C discharge rate. The low-temperature performance of the cathode was further evaluated, showing 0.5C discharge capacity of 122 and 119 mAh/g at −25 and −40 °C, respectively. The discharge capacity of graphite//Li₃V₂(PO₄)₃ batteries with a designed battery capacity of 14 Ah is as high as 109 mAh/g with a capacity retention of 92% after 224 cycles at 2C discharge rates. The promising high-rate and low-temperature performance observed in this work suggests that Li₃V₂(PO₄)₃/C is a very strong candidate to be a cathode in a next-generation Li-ion battery for electric vehicle applications.     

Preparation and electrochemical properties of LiCoO2-LiNi0.5Mn0.5O2-Li2MnO3 solid solutions with high Mn contents

The solid solutions LiCoO₂-LiNi_1/2Mn_1/2O₂-Li₂MnO₃ with higher Mn content have been prepared by a spray drying method between 750 and 950 °C and their electrochemical performances have also been characterized. The effects of the Li content on the structure and electrochemical performance of the samples have been studied. It was found that their lattice parameters a, c and V increase with the increase in Ni content and the decrease in Co content. The solid solutions xLiCoO₂-yLiNi_1/2Mn_1/2O₂-(1−x−y)Li₂MnO₃ with x = 0.18, 0.27 and y = 0.2 have the largest discharge capacity, which is more than 200 mAh/g in the voltages of 3.0-4.6 V. It is believed that the optimum Co content x in xLiCoO₂-yLiNi_1/2Mn_1/2O₂-(1−x−y)Li₂MnO₃ is between 0.2 and 0.3 in the charge-discharge voltage range of 3.0-4.6 V. The solid solutions xLiCoO₂-yLiNi_1/2Mn_1/2O₂-(1−x−y)Li₂MnO₃ with x = 0.18-0.36 and y = 0.2 have the excellent cycling performance and the capacity retention attains to almost 100% after 50 cycles. Moreover, it is found that the discharge capacity gradually increases with the increment of cycle number especially in the initial 10 cycles. XRD showed that the layered structure has been kept all the time in 20 cycles, which is perhaps the reason why the sample has the excellent cycling performance.     

Preparation and electrical conductivity of polyethers/WS2 layered nanocomposites

Utilizing the solvothermal synthesis technique, lithium intercalated tungsten disulfide Li_xWS₂ with x > 1 was obtained, which was allowed to react with water to the formation of single-molecule-layer suspension of tungsten disulfide. The layered nanocomposites PEG, PEO/WS₂, intercalating poly(ethylene glycol) (PEG, MW ≈ 1 × 10³, 6 × 10³, 1 × 10⁴) and poly(ethylene oxide) (PEO, MW ≈ 3 × 10⁵) into the tungsten disulfide host galleries, were prepared using the improved exfoliation-adsorption technique. It was revealed that the intercalated polymers within the host galleries are in a double-layer arrangement with an interlayer expansion of about 9 Å. Despite high conductivity of the host material, those of the PEG, PEO/WS₂ nanocomposites were found to be high in the order of 1 × 10⁻² to 10⁻³ S cm⁻¹ at ambient temperature, resulted from the guest-host charge transfers.     

Hydrothermal synthesis of Zn-doped Li4Ti5O12 with improved high rate properties for lithium ion batteries

Hydrothermal method has been successfully used to synthesize a spheroidic zinc doped Li₄Ti₅O₁₂ (Li_3.95Zn_0.05Ti₅O₁₂) with large specific surface area. X-ray diffraction (XRD) and scanning electron microscope (SEM) are used to characterize the structure and morphology. The electrochemical properties are measured by the galvanostatic method and the results demonstrate that the Li₄Ti_3.95Zn_0.05O₁₂ has a large discharge capacity of 182.45 mAh/g at 0.1C. With the favorable transport channel caused by the doped Zn²⁺, the Li_3.95Zn_0.05Ti₅O₁₂ exhibits an enhanced high rate capacity of 122.38 mAh/g and better cyclic stability at 10C, which is promising for application in lithium ion batteries.     

Electrochemical performance of the carbon coated Li3V2(PO4)3 cathode material synthesized by a sol-gel method

A carbon coated Li₃V₂(PO₄)₃ cathode material for lithium ion batteries was synthesized by a sol-gel method using V₂O₅, H₂O₂, NH₄H₂PO₄, LiOH and citric acid as starting materials, and its physicochemical properties were investigated using X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) spectroscopy, scanning electron microscopy (SEM), energy dispersive analysis of X-ray (EDAX), transmission electron microscope (TEM), and electrochemical methods. The sample prepared displays a monoclinic structure with a space group of P2₁/n, and its surface is covered with a rough and porous carbon layer. In the voltage range of 3.0-4.3 V, the Li₃V₂(PO₄)₃ electrode displays a large reversible capacity, good rate capability and excellent cyclic stability at both 25 and 55 °C. The largest reversible capacity of 130 mAh g⁻¹ was obtained at 0.1C and 55 °C, nearly equivalent to the reversible cycling of two lithium ions per Li₃V₂(PO₄)₃ formula unit (133 mAh g⁻¹). It was found that the increase in total carbon content can improve the discharge performance of the Li₃V₂(PO₄)₃ electrode. In the voltage range of 3.0-4.8 V, the extraction and reinsertion of the third lithium ion in the carbon coated Li₃V₂(PO₄)₃ host are almost reversible, exhibiting a reversible capacity of 177 mAh g⁻¹ and good cyclic performance. The reasons for the excellent electrochemical performance of the carbon coated Li₃V₂(PO₄)₃ cathode material were also discussed.     

Synthesis and characterization of carbon-coated Li0.5Ni0.25TiOPO4 anode material

Li_0.5Ni_0.25TiOPO₄/C composite was synthesized by the co-precipitation method using polyethylene glycol as carbon source. X-ray diffraction study showed that the as-prepared material crystallizes in the monoclinic system (S.G. P2₁/c). This 3D structure exhibits an open framework favourable to intercalation reactions. The morphology and the microstructure characterisation was performed by scanning electron microscopy (SEM). Small particles (∼1 μm) coated by carbon were observed. Raman study confirms the presence of carbon graphite in the Li_0.5Ni_0.25TiOPO₄/C composite. Cyclic voltammetry (CV) and charge-discharge galvanostatic cycling were used to characterize its electrochemical properties. The Li_0.5Ni_0.25TiOPO₄/C composite exhibits excellent electrochemical performances with good capacity retention for 50 cycles. Approximately 200 mAh/g could be reached at C, C/2, C/5 and C/20 rates in the 0.5-3 V potential range. These results clearly evidenced the positive effect of the carbon coating on the electrochemical properties of the studied phosphate.     

XPS study of Li ion intercalation in V2O5 thin films prepared by thermal oxidation of vanadium metal

The intercalation and deintercalation mechanisms of lithium into V₂O₅ thin films prepared by thermal oxidation of vanadium metal have been studied by X-ray photoelectron spectroscopy (XPS) using a direct anaerobic and anhydrous transfer from the glove box (O₂ and H₂O < 1ppm), where the samples were electrochemically treated, to the XPS analysis chamber. Vanadium in the as-prepared oxide films is mostly (from 93 to 96% depending on samples) in a pentavalent state (V⁵⁺) with a stoichiometric O/V concentration ratio fitting that of V₂O₅. Four to seven percent of VO₂ is also observed. After the 1st and the 2nd intercalation steps at E = 3.3 and 2.8 V versus Li/Li⁺, respectively, the V2p core level spectra evidence a partial reduction to V⁴⁺ states with a remaining concentration of 73 and 56% of V⁵⁺, in agreement with the intercalation of about 1/2 mol of Li per V₂O₅ mol at each intercalation step. Intercalated lithium was observed at a binding energy of 56.1 eV for Li1s. Changes of the electronic structure of the V₂O₅ thin film after intercalation are evidenced by the observation, at a binding energy of 1.3 eV, of occupied V3d states (V⁴⁺) originally empty in the pristine film (V⁵⁺). The V2p and Li1s core level spectra show that the process of Li intercalation is partially irreversible. In the first cycle, 34 and 14% of the vanadium ions remain in the V⁴⁺ state after deintercalation at E = 3.4 and 3.8 V versus Li/Li⁺, respectively, indicating a partially irreversible process already after the 1st deintercalation. The analyses of C1s and O1s XP spectra show the formation of a solid-electrolyte interface (SEI). The analyzed surface layer includes lithium carbonate and Li-alkoxides.     

ZnLi2/3Ti4/3O4: A new low loss spinel microwave dielectric ceramic

A new low loss spinel microwave dielectric ceramic with composition of ZnLi_2/3Ti_4/3O₄ was synthesized by the conventional solid-state ceramic route. The ceramic can be well densified after sintering above 1075 °C for 2 h in air. X-ray diffraction data show that ZnLi_2/3Ti_4/3O₄ ceramic has a cubic structure [Fd-3m (227)] similar to MgFe₂O₄ with lattice parameters of a = 8.40172 Å, V = 593.07 Å³, Z = 8 and ρ = 4.43 g/cm³. The best microwave dielectric properties can be obtained in ceramic with relative permittivity of 20.6, Q × f value of 106,700 GHz and τ_f value of −48 ppm/°C. The addition of BaCu(B₂O₅) (BCB) can effectively lower the sintering temperature from 1075 °C to 900 °C and does not induce much degradation of the microwave dielectric properties. Compatibility with Ag electrode indicates that the BCB added ZnLi_2/3Ti_4/3O₄ ceramics are good candidates for LTCC applications.     

Isothermal calorimetry investigation of Li1+xMn2−yAlzO4 spinel

The heat generation of LiMn₂O₄, Li_1.156Mn_1.844O₄, and Li_1.06Mn_1.89Al_0.05O₄ spinel cathode materials in a half-cell system was investigated by isothermal micro-calorimetry (IMC). The heat variations of the Li/LiMn₂O₄ cell during charging were attributed to the LiMn₂O₄ phase transition and order/disorder changes. This heat variation was largely suppressed when the stoichiometric spinel was doped with excess lithium or lithium and aluminum. The calculated entropy change (dE/dT) from the IMC confirmed that the order/disorder change of LiMn₂O₄, which occurs in the middle of the charge, was largely suppressed with lithium or lithium and aluminum doping. The dE/dT values obtained did not agree between the charge and the discharge at room temperature (25 °C), which was attributed to cell self-discharge. This discrepancy was not observed at low temperature (10 °C). Differential scanning calorimeter (DSC) results showed that the fully charged spinel with lithium doping has better thermal stability.     

Crystal structure and electrochemical performance of Li3V2(PO4)3 synthesized by optimized microwave solid-state synthesis route

To investigate the crystal structure and electrochemical performance of samples synthesized under different microwave solid-state synthesis condition, a series of Li₃V₂(PO₄)₃ samples has been synthesized at five different temperatures for 3-5 min and at 750 °C for various time. The as-synthesized Li₃V₂(PO₄)₃ samples are characterized and studied by ICP-AES analysis, X-ray diffraction (XRD), Rietveld analysis, scanning and transmission electron microcopy (SEM and TEM). At relatively lower temperature (650 °C) and very short reaction time (3 min), pure phase of Li₃V₂(PO₄)₃ could be synthesized in microwave irradiation field. The crystal structure and Li atomic fractional coordinate present a significant deviation upon the change of microwave irradiation temperature and time. Relatively, the diffusion ability of lithium cations and the electrochemical performance are affected. Under the proper reaction temperature and time, the carbon-free samples MW750C5m and MW850C3m show the best specific discharge capacity 126.4 and 132 mAh g⁻¹ at the voltage range of 3.0-4.3 V, near the reversible cycling of two lithium ions per Li₃V₂(PO₄)₃ formula unit (133 mAh g⁻¹). At the voltage range of 3-4.8 V, the sample MW750C5m presents the best initial specific charge capacity of 197 mAh g⁻¹, equivalent to the reversible cycling of three lithium ions per Li₃V₂(PO₄)₃ formula unit (197 mAh g⁻¹). The initial discharge capacity, the samples MW750C5m and MW850C3m present high specific discharge capacity 183.4 and 175.7 mAh g⁻¹, respectively. The relationship among microwave irradiation condition, crystal structure, lithium atomic fractional coordinates and the electrochemical performance have been discussed in detail.