Particle size effect of Li[Ni0.5Mn0.5]O2 prepared by co-precipitation

Spherical (Ni_0.5Mn_0.5)(OH)₂ with different secondary particle size (3 μm, 10 μm in diameter) was synthesized by co-precipitation method. Mixture of the prepared hydroxide and lithium hydroxide was calcined at 950 °C for 20 h in air. X-ray diffraction patterns revealed that the prepared material had a typical layered structure with space group. Spherical morphologies with mono-dispersed powders were observed by scanning electron microscopy. It was found that the layered Li[Ni_0.5Mn_0.5]O₂ delivered an initial discharge capacity of 148 mAh g⁻¹ (3.0-4.3 V) though the particle sizes were different. Li[Ni_0.5Mn_0.5]O₂ having smaller particle size (3 μm) showed improved area specific impedance due to the reduced Li⁺ diffusion path, compared with that of Li[Ni_0.5Mn_0.5]O₂ possessing larger particle size (10 μm). Although the Li[Ni_0.5Mn_0.5]O₂ (3 μm) was electrochemically delithiated to Li_0.39[Ni_0.5Mn_0.5]O₂, the resulting exothermic onset temperature was around 295 °C, of which the value is significantly higher than that of highly delithiated Li_1−δCoO₂ (∼180 °C).     

Synthesis of spherical Li[Ni(1/3−z)Co(1/3−z)Mn(1/3−z)Mgz]O2 as positive electrode material for lithium-ion battery

Li[Ni_(1/3−z)Co_(1/3−z)Mn_(1/3−z)Mg_z]O₂ (z = 0, 0.04) positive electrode materials were synthesized via a co-precipitation method. These materials have α-NaFeO₂ () structure, as confirmed by X-ray diffraction (XRD) studies. Cation mixing in Li layer seemed to be decreased by Mg substitution as examined by Rietveld refinements of XRD data. Spherical morphologies were observed for the as-synthesized final products by scanning electron microscopy. Their electrochemical properties during charge and discharge were discussed. When magnesium ions are substituted, the initial reversible capacity reduced. However, the substitution for Mn sites in Li[Ni_1/3Co_1/3Mn_1/3]O₂ did not decrease the capacity because Mn sites substitution did not result in loss of electroactive elements in the compound. Differential scanning calorimetric studies showed the exothermic peaks of the charged electrode Li[Ni_(1/3−z)Co_(1/3−z)Mn_(1/3−z)Mg_z]O₂ (z = 0.04) were significantly smaller than that of Li[Ni_1/3Co_1/3Mn_1/3]O₂, which means that thermal stability was greatly improved by Mg substitution even at highly delithiated state.     

Zr-doped Li[Ni0.5−xMn0.5−xZr2x]O2 (x = 0, 0.025) as cathode material for lithium ion batteries

Layered Li[Ni_0.5−xMn_0.5−xZr_2x]O₂ (x = 0, 0.025) have been prepared by the mixed hydroxide and molten-salt synthesis method. The individual particles of synthesized materials have a sub-microsize range of 200-500 nm, and LiNi_0.475Mn_0.475Zr_0.05O₂ has a rougher surface than that of LiNi_0.5Mn_0.5O₂. The Li/Li[Ni_0.5−xMn_0.5−xZr_2x]O₂ (x = 0, 0.025) electrodes were cycled between 4.5 and 2.0 V at a current density of 15 mA/g, the discharge capacity of both cells increased during the first ten cycles. The discharge capacity of the Li/LiNi_0.475Mn_0.475Zr_0.05O₂ cell increased from 150 to 220 mAh/g, which is 50 mAh/g larger than that of the Li/LiNi_0.5Mn_0.5O₂ cell. We found that the oxidation of oxygen and the Mn³⁺ ion concerned this phenomenon from the cyclic voltammetry (CV). Thermal stability of the charged Li[Ni_0.5−xMn_0.5−xZr_2x]O₂ (x = 0, 0.025) cathode was improved by Zr doping.     

Effect of synthesis condition on the structure and electrochemical properties of Li[Ni1/3Mn1/3Co1/3]O2 prepared by hydroxide co-precipitation method

The layered Li[Ni_1/3Co_1/3Mn_1/3]O₂ powder with good crystalline and spherical shape was prepared by hydroxide co-precipitation method. The effects of pH value, NH₄OH amount, calcination temperature and extra Li amount on the morphology, structure and electrochemical properties of the cathode material were investigated in detail. SEM results indicate that pH value affected both the morphology and the property of the cathode material, and the highest discharge capacity in the first cycle of 163 mAh g⁻¹ (2.8-4.3 V) was obtained at pH value was 12. On the contrary, the NH₄OH amount, which was used as a chelating agent, only affected the particle size distribution of the material. The calcination temperatures caused great difference in the structure and property of layered Li[Ni_1/3Co_1/3Mn_1/3]O₂, and the best electrochemical properties were obtained at the calcination temperature of 800 °C. Extra Li amount not only caused difference in the material structure, but also affected their electrochemical properties. With increasing Li amount, the lattice parameters (a and c) increased monotonously, and the highest first cycle coulombic efficiency (the ratio of discharge capacity to charge capacity in the first cycle) was obtained with the Li/M of 1.10. Therefore, the optimum synthetic conditions for the hydroxide co-precipitation reaction were: pH value was 12, NH₄OH amount was 0.36 mol L⁻¹, calcination temperature was 800 °C and the Li/M molar ratio was 1.10.     

Synthetic optimization of spherical Li[Ni1/3Mn1/3Co1/3]O2 prepared by a carbonate co-precipitation method

A carbonate co-precipitation method was employed to prepare spherical Li[Ni_1/3Co_1/3Mn_1/3]O₂ cathode material. The precursor, [Ni_1/3Co_1/3Mn_1/3]CO₃, was prepared using ammonia as chelating agent under CO₂ atmosphere. The spherical Li[Ni_1/3Co_1/3Mn_1/3]O₂ was prepared by mixing the precalcined [Ni_1/3Co_1/3Mn_1/3]CO₃ with LiOH followed by high temperature calcination. The preparation conditions such as ammonia concentration, co-precipitation temperature, calcination temperature and Li/[Ni_1/3Co_1/3Mn_1/3] ratio were varied to optimize the physical and electrochemical properties of the prepared Li[Ni_1/3Co_1/3Mn_1/3]O₂. The structural, morphological, and electrochemical properties of the prepared LiNi_1/3Co_1/3Mn_1/3O₂ were characterized by XRD, SEM, and galvanostatic charge-discharge cycling. The optimized material has a spherical particle shape and a well ordered layered structure, and it also has an initial discharge capacity of 162.7 mAh g^− 1 in a voltage range of 2.8-4.3 V and a capacity retention of 94.8% after a hundred cycles. The optimized ammonia concentration, co-precipitation temperature, calcination temperature, and Li/[Ni_1/3Co_1/3Mn_1/3] ratio are 0.3 mol L^− 1, 60 °C, 850 °C, and 1.10, respectively.     

Structural modification of Li[Li0.27Co0.20Mn0.53]O2 by lithium extraction and its electrochemical property as the positive electrode for Li-ion batteries

In our previous report, we have synthesized Li₂MnO₃-LiCoO₂ solid solutions and have investigated electrochemical properties [J.-M. Kim, T. Sho, N. Kumagai, Electrochem. Commun. 9 (2007) 103]. These materials have showed a long charge plateau at above 4.5 V during the first charge, which disappears with the subsequent cycles. This phenomenon is usually observed in Li₂MnO₃ and Li₂MnO₃-LiMeO₂ system (Me = Ni_1/2Mn_1/2 [Z. Lu, D.D. MacNeil, J.R. Dahn, Electrochem. Solid State Lett. 4 (2001) 191], Co [K. Numata, C. Sakaki, S. Yamanaka, Solid State Ionics 117 (1999) 257; Y.J. Park, Y.-S. Hong, X. Wu, M.K. Kim, K.S. Ryu, S.H. Chang, J. Electrochem. Soc. 151 (2004) A720], Fe [M. Tabuchi, A. Nakashima, H. Shigemura, K. Ado, H. Kobayashi, H. Sakaebe, H. Kageyama, T. Nakamura, M. Kohzaki, A. Hirano, R. Kanno, J. Electrochem. Soc. 149 (2002) A509], or Cr [B. Ammundsen, J. Paulsen, Adv. Mater. 13 (2001) 943]). In this study, we investigate the relationship between the first lithium extraction process and the electrochemical property of the synthesized Li[Li_0.27Co_0.2Mn_0.53]O₂ material. The crystal structure and electrochemical performance of the synthesized Li[Li_0.27Co_0.20Mn_0.53]O₂ are modified by the Li⁺ extraction.     

Synthetic optimization of Li[Ni1/3Co1/3Mn1/3]O2 via co-precipitation

Li[Ni_1/3Co_1/3Mn_1/3]O₂ powders were synthesized from co-precipitated spherical metal hydroxide, (Ni_1/3Co_1/3Mn_1/3)(OH)₂. The preparation of metal hydroxide was significantly dependent on synthetic conditions, such as pH, amount of chelating agent, stirring speed, etc. The optimized condition resulted in (Ni_1/3Co_1/3Mn_1/3)(OH)₂, of which the particle size distribution was uniform and the particle shape was spherical, as observed by scanning electron microscopy. Calcination of the uniform metal hydroxide with LiOH at higher temperature led to a well-ordered layer-structured Li[Ni_1/3Co_1/3Mn_1/3]O₂, as confirmed by Rietveld refinement of X-ray diffraction pattern. Due to the homogeneity of the metal hydroxide, (Ni_1/3Co_1/3Mn_1/3)(OH)₂, the final product, Li[Ni_1/3Co_1/3Mn_1/3]O₂, was also significantly uniform, i.e., the average particle size was of about 10 μm in diameter and the distribution was relatively narrow. As a result, the corresponding tap-density was also high approximately 2.39 g cm−3, of which the value is comparable to that of commercialized LiCoO₂. In the voltage range of 2.8-4.3, 2.8-4.4, and 2.8-4.5 V, the discharge capacities of Li[Ni_1/3Co_1/3Mn_1/3]O₂ electrode were 159, 168, and 177 mAh g⁻¹, respectively. For elevated temperature operation (55 °C), the resulted capacity was of about 168 mAh g⁻¹ with an excellent cyclability.     

Improved electrochemical properties of Li1+x(Ni0.3Co0.4Mn0.3)O2−δ (x = 0, 0.03 and 0.06) with lithium excess composition prepared by a spray drying method

Layered Li_1+x(Ni_0.3Co_0.4Mn_0.3)O_2−δ (x = 0, 0.03 and 0.06) materials were synthesized through the different calcination times using the spray-dried precursor with the molar ratio of Li/Me = 1.25 (Me = transition metals). The physical and electrochemical properties of the lithium excess and the stoichiometric materials were examined using XRD, AAS, BET and galvanostatic electrochemical method. As results, the lithium excess Li_1.06(Ni_0.3Co_0.4Mn_0.3)O_2−δ could show better electrochemical properties, such as discharge capacity, capacity retention and C rate ability, than those of the stoichiometric Li_1.00(Ni_0.3Co_0.4Mn_0.3)O_2−δ. In this paper, the effect of excess lithium on the electrochemical properties of Li_1+x(Ni_0.3Co_0.4Mn_0.3)O_2−δ materials will be discussed based on the experimental results of ex situ X-ray diffraction, transmission electron microscopy (TEM) and galvanostatic intermittent titration technique (GITT)     

Effect of synthesis condition on the structural and electrochemical properties of Li[Ni1/3Mn1/3Co1/3]O2 prepared by the metal acetates decomposition method

In order to get homogeneous layered oxide Li[Ni_1/3Mn_1/3Co_1/3]O₂ as a lithium insertion positive electrode material, we applied the metal acetates decomposition method. The oxide compounds were calcined at various temperatures, which results in greater difference in morphological (shape, particle size and specific surface area) and the electrochemical (first charge profile, reversible capacity and rate capability) differences. The Li[Ni_1/3Mn_1/3Co_1/3]O₂ powders were characterized by means of X-ray diffraction (XRD), charge/discharge cycling, cyclic voltammetry and SEM. XRD experiment revealed that the layered Li[Ni_1/3Mn_1/3Co_1/3]O₂ material can be best synthesized at temperature of 800 °C. In that synthesized temperature, the sample showed high discharge capacity of 190 mAh g⁻¹ as well as stable cycling performance at a current density of 0.2 mA cm⁻² in the voltage range 2.3-4.6 V. The reversible capacity after 100 cycles is more than 190 mAh g⁻¹ at room temperature.     

Electrochemical performance of LiV3−xNixO8 cathode materials synthesized by a novel low-temperature solid-state method

A series of cathode materials for lithium ion batteries with the formula LiV_3−xNi_xO₈ (x = 0.000, 0.025, 0.050 and 0.100) have been synthesized by a novel low-temperature solid-state method. The synthesized cathode materials have been characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), discharge-charge test, cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). These results indicate that LiV_2.95Ni_0.050O₈ shows much better electrochemical performances than LiV₃O₈. This is due to better electrochemical reversibility and lower particle-to-particle resistance after Ni²⁺ doping.     

Hydrothermal synthesis of LiNixCo1−xO2 cathode materials

Ultrafine powders of LiCoO₂, nonstoichiometric LiNiO₂ and LiNi_0.9Co_0.1O₂ were prepared under mild hydrothermal conditions. The influence of the molar ratio of Li/Co, Li/Ni and Li/(Ni + Co) was studied. The final products were investigated by XRD, TEM and EDS. To synthesize a stoichiometric LiNiO₂ under mild hydrothermal conditions was found to be a big challenge. Transmission electron microscopies (TEM) revealed the formation of well-crystallized LiCoO₂ and LiNi_0.9Co_0.1O₂ with average size of 100 nm and 10 nm, respectively.     

Electrochemical and thermal studies of Li[NixLi(1/3−2x/3)Mn(2/3−x/3)]O2 (x = 1/12, 1/4, 5/12, and 1/2)

Samples of the layered cathode materials, Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ (x = 1/12, 1/4, 5/12, and 1/2), were synthesized at 900 °C. Electrodes of these samples were charged in Li-ion coin cells to remove lithium. The charged electrode materials were rinsed to remove the electrolyte salt and then added, along with EC/DEC solvent or 1 M LiPF₆ EC/DEC, to stainless steel accelerating rate calorimetry (ARC) sample holders that were then welded closed. The reactivity of the samples with electrolyte was probed at two states of charge. First, for samples charged to near 4.45 V and second, for samples charged to 4.8 V, corresponding to removal of all mobile lithium from the samples and also concomitant release of oxygen in a plateau near 4.5 V. Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples with x = 1/4, 5/12 and 1/2 charged to 4.45 V do not react appreciably till 190 °C in EC/DEC. Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples charged to 4.8 V versus Li, across the oxygen release plateau, start to significantly react with EC/DEC at about 130 °C. However, their high reactivity is similar to that of Li_0.5CoO₂ (4.2 V) with 1 μm particle size. Therefore, Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples showing specific capacity of up to 225 mAh/g may be acceptable for replacing LiCoO₂ (145 mAh/g to 4.2 V) from a safety point of view, if their particle size is increased.     

Amorphous LiCoO2 thin films on Li1+x+yAlxTi2−xSiyP3−yO12 prepared by radio frequency magnetron sputtering for all-solid-state Li-ion batteries

Amorphous LiCoO₂ thin films were deposited on the NASICON-type glass ceramics, Li_1+x+yAl_xTi_2−xSi_yP_3−yO₁₂ (LATSP), by radio frequency (RF) magnetron sputtering below 180 °C. The as-deposited LiCoO₂ thin films were characterized by X-ray diffraction, scanning electron microscopy and atomic force microscope. All-solid-state Li/PEO₁₈-Li (CF₃SO₂)₂N/LATSP/LiCoO₂/Au cells were fabricated using the amorphous film. The electrochemical performance of the cells was investigated by galvanostatic cycling, cyclic voltammetry, potentiostatic intermittent titration technique and electrochemical impedance spectroscopy. It was found that the amorphous LiCoO₂ thin film shows a promising electrochemical performance, making it a potential application in microbatteries for microelectronic devices.     

A novel layered Li [Li0.12NizMg0.32−zMn0.56]O2 cathode material for lithium-ion batteries

Layered Li[Li_0.12Ni_zMg_0.32−zMn_0.56]O₂ oxide cathodes containing lithium atoms in the transition metal layers were synthesized and characterized using X-ray diffraction (XRD), galvanostatic cycling, and differential scanning calorimetry (DSC). The Li[Li_0.12Ni_zMg_0.32−zMn_0.56]O₂ cathodes deliver a specific discharge capacity of about 190 mAh/g at room temperature and 236 mAh/g at 55 °C when cycled between 2.7 and 4.6 V versus Li/Li⁺. Excellent capacity retention and smooth potential profiles at room and elevated temperatures over extended cycles suggest that this material does not convert into a spinel structure.     

Enhanced electrochemical and thermal stability of surface-modified LiCoO2 cathode by CeO2 coating

CeO₂-coated LiCoO₂ particles were successfully synthesized by a sol-gel coating of CeO₂ on the surface of the LiCoO₂ powder and subsequent heat treatment at 700 °C for 5 h. The surface-modified and pristine LiCoO₂ powders were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), Auger electron spectroscopy (AES), slow rate cyclic voltammogram (CV), and differential scanning calorimetry (DSC). Cyclic voltammetry curves suggested that the CeO₂ coating suppressed the phase transitions. Unlike pristine LiCoO₂, the CeO₂-coated LiCoO₂ cathode exhibited better capacity retention than the pristine LiCoO₂ electrode in the higher cutoff voltage. Differential scanning calorimetric data revealed the higher thermal stability of the CeO₂-coated LiCoO₂ electrode.     

Characterization of high tap density Li[Ni1/3Co1/3Mn1/3]O2 cathode material synthesized via hydroxide co-precipitation

Li[Ni_1/3Co_1/3Mn_1/3]O₂ cathode material for lithium ion batteries was prepared by mixing metal hydroxide, (Ni_1/3Co_1/3Mn_1/3)(OH)₂, with 6% excess LiOH followed by calcinations. The (Ni_1/3Co_1/3Mn_1/3)(OH)₂ with secondary particle of about 12 μm was prepared by hydroxide co-precipitation. The tap density of the obtained Li[Ni_1/3Co_1/3Mn_1/3]O₂ powder was 2.56 ± 0.21 g cm⁻³. The powder was characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), particle size distribution (PSD) and galvanostatic charge-discharge cycling. The XRD pattern of Li[Ni_1/3Co_1/3Mn_1/3]O₂ revealed a well ordered hexagonal layered structure with low cation mixing. Secondary particles with size of 13-14 μm and primary particles with size of about 1 μm can be identified from the SEM observations. In the voltage range of 2.8-4.3 V, the initial discharge capacity of the Li[Ni_1/3Co_1/3Mn_1/3]O₂ electrode was 166.6 mAh g⁻¹, and 96.5% of the initial capacity was retained after 50 charge-discharge cycling.     

Optimum synthesis of Li2Fe1−xMnxSiO4/C cathode for lithium ion batteries

Li₂Fe_1−xMn_xSi0₄/C cathode materials were synthesized by mechanical activation-solid-state reaction. The effects of Mn-doping content, roasting temperature, soaking time and Li/Si molar ratio on the physical properties and electrochemical performance of the Li₂Fe_1−xMn_xSi0₄/C composites were investigated. The materials were characterized by X-ray diffraction (XRD) and scanning electron microscope (SEM), charge-discharge tests and AC impedance measurements. SEM images suggest that the morphology of the Li₂Fe_1−xMn_xSi0₄/C composite is sensitive to the reaction temperature. Samples synthesized at different temperatures have different extent of agglomeration. Being charged-discharged at C/32 between 1.5 and 4.8 V, the Li₂Fe_0.9Mn_0.1Si0₄/C synthesized at the optimum conditions shows good electrochemical performances with an initial discharge capacity of 158.1 mAh g⁻¹ and a capacity retention ratio of 94.3% after 30 cycles. AC impendence investigation shows Li₂Fe_0.9Mn_0.1SiO₄/C have much lower resistance of electrode/electrolyte interface than Li₂FeSiO₄/C.     

Effect of fluorine in the preparation of Li(Ni1/3Co1/3Mn1/3)O2 via hydroxide co-precipitation

Uniform and spherical Li(Ni_1/3Co_1/3Mn_1/3)O_(2−δ)F_δ powders were synthesized via NH₃ and F⁻ coordination hydroxide co-precipitation. The effect of F⁻ coordination agent on the morphology, structure and electrochemical properties of the Li(Ni_1/3Co_1/3Mn_1/3)O_(2−δ)F_δ were studied. The morphology, size, and distribution of (Ni_1/3Co_1/3Mn_1/3)(OH)_(2−δ)F_δ particle diameter were improved in a shorter reaction time through the addition of F⁻. The study suggested that the added F improves the layered characteristics of the lattice and the cyclic performance of Li(Ni_1/3Co_1/3Mn_1/3)O₂ in the voltage range of 2.8-4.6 V. The initial capacity of the Li(Ni_1/3Co_1/3Mn_1/3)O_1.96F_0.04 was 178 mAh g⁻¹, the maximum capacity was 186 mAh g⁻¹ and the capacity after 50 cycles was 179 mAh g⁻¹ in the voltage range of 2.8-4.6 V.