Experimental Evaluation of Compressive Behavior of Orthotropic Steel Plates for the New San Francisco–Oakland Bay Bridge

Compression tests were conducted on two reduced-scale orthotropic plates to verify the design strength of steel box girders for the new San Francisco–Oakland Bay Bridge. The first specimen was composed of three longitudinal closed ribs and a top deck plate. It failed in global buckling, followed by local buckling in the deck plate and ribs. The second specimen, which was composed of four longitudinal T-shaped ribs and a bottom deck plate, experienced global buckling as well as local buckling in the ribs and the deck plate. The ultimate strength and failure mode of both specimens were evaluated by two bridge design specifications: the 1998 AASHTO load and resistance factor design specification and the 2002 Japanese JRA specification. Findings from code comparisons showed that: (1) Sufficient flexural rigidity of ribs were provided for both specimens; (2) the JRA specification slightly overestimated the ultimate strength of both specimens; and (3) neither specifications predicted the observed buckling sequence in Specimen 2. A general-purpose nonlinear finite element analysis program (ABAQUS) was used to perform correlation study. The analysis showed that the ultimate strength and postbuckling behavior of the specimens could be reliably predicted when both the effects of residual stresses and initial geometric imperfections were considered in the model.     

Dynamic Response of Three Fiber Reinforced Polymer Composite Bridges

Fiber reinforced polymer (FRP) composite bridge decks are gaining the attention of bridge owners because of their light self-weight, corrosion resistance, and ease of installation. Constructed Facilities Center at West Virginia University working with the Federal Highway Administration and West Virginia Department of Transportation has developed three different FRP decking systems and installed several FRP deck bridges in West Virginia. These FRP bridge decks are lighter in weight than comparable concrete systems and therefore their dynamic performance is equally as important as their static performance. In the current study dynamic tests were performed on three FRP deck bridges, namely, Katy Truss Bridge, Market Street Bridge, and Laurel Lick Bridge, in the state of West Virginia. The dynamic response parameters evaluated for the three bridges include dynamic load allowance (DLA) factors, natural frequencies, damping ratios, and deck accelerations caused by moving test trucks. It was found that the DLA factors for Katy Truss and Market Street bridges are within the AASHTO 1998 LRFD specifications, but the deck accelerations were found to be high for both these bridges. DLA factors for Laurel Lick bridge were found to be as high as 93% against the typical design value of 33%; however absolute deck stress induced by vehicle loads is less than 10% of the deck ultimate stress.     

Impact Factors for Curved Continuous Composite Multiple-Box Girder Bridges

The results from a parametric study on the impact factors for 180 curved continuous composite multiple-box girder bridges are presented. Expressions for the impact factors for tangential flexural stresses, deflection, shear forces and reactions are deduced for AASHTO truck loading. The finite-element method was utilized to model the bridges as three-dimensional structures. The vehicle axle used in the analysis was simulated as a pair of concentrated forces moving along the concrete deck in a circumferential path with a constant speed. The effects of bridge configurations, loading positions, and vehicle speed on the impact factors were examined. Bridge configurations included span length, span-to-radius of curvature ratio, number of lanes, and number of boxes. The effect of the mass of the vehicle on the dynamic response of the bridges is also investigated. The data generated from the parametric study and the deduced expressions for the impact factors would enable bridge engineers to design curved continuous composite multiple-box girder bridges more reliably and economically.     

Approximate Series Solution for Analysis of FRP Composite Highway Bridges

The design of a deck-and-stringer bridge system is usually reduced to the analysis of a T-beam section, loaded by concentrated loads corresponding to an equivalent fraction of the applied truck load. This equivalent load is defined by wheel load–distribution factors, which approximate the overall behavior of the bridge superstructure. In this paper, a one-term approximation of a macroflexibility series solution including deformations for fiber-reinforced polymer (FRP) deck-and-stringer orthotropic bridge systems, is used to develop explicit expressions for symmetric and asymmetric load distribution factors. It is significant that the equations presented herein include important parameters that represent, as accurately as possible, the response characteristics of the super structure, such as the geometry and material properties of the FRP deck and stringers, bridge aspect ratio, and number and spacing of stringers. As an illustration in actual design applications, the formulation presented in this paper is used to develop an analytical method for FRP deck-and-stringer bridge systems, and the method is verified by predicting the response of an all FRP model bridge in the lab and an FRP deck on steel stringers in the field. The results of the present formulation compare well with experimental lab and field results. The simplified analysis presented in this paper can be used with sufficient accuracy for the design of composite FRP deck on stringers bridges.     

Refined Stick Model for Dynamic Analysis of Skew Highway Bridges

Stick models are widely employed in the dynamic analysis of bridges when only approximate results are desired or when detailed models are difficult or time-consuming to construct. Although the use of stick models for regular bridges has been validated by various researchers, the application of such models to skew highway bridges continues to present challenges. The conventional single-beam stick model used to represent the bridge deck often fails to capture certain predominant vibration modes that are important in obtaining the true dynamic response of the bridge. In this paper, a refined stick model is proposed for the preliminary dynamic analysis of skew bridges. The model utilizes a dual-beam stick representation of the bridge deck. The validity of the model is established by comparing results obtained from the proposed model with numerical solutions obtained for skew plates and a skew bridge. It is shown that this dual-beam stick model is superior to the conventional single-beam model in estimating the natural vibration frequencies and in predicting the predominant vibration modes of the bridge. Because of its simplicity and relative accuracy, this model is recommended for the preliminary dynamic analysis of skew highway bridges.     

Fuzzy Logic Based Condition Rating of Existing Reinforced Concrete Bridges

Fuzzy logic is a means for modeling the uncertainty involved in describing an event/result using natural language. The fuzzy logic approach would be particularly useful for remedying the uncertainties and imprecision in bridge inspectors’ observations. This study explores the possibilities of using fuzzy mathematics for condition assessment and rating of bridges, developing a systematic procedure and formulations for rating existing bridges using fuzzy mathematics. Computer programs developed from formulations presented in this paper are used for evaluating the rating of existing bridges, and the details are presented in the paper. In this approach, the entire bridge has been divided into three major components—deck, superstructure, and substructure—each of which is further subdivided into a number of elements. Using fuzzy mathematics in combination with an eigenvector-based priority setting approach, the resultant rating set for the bridge has been evaluated based on the specified ratings and importance factors for all the elements of the bridge. Then the defuzzified value of the resultant rating fuzzy set becomes the rating value for the bridge as a whole. It is argued that the methodology presented in this paper would help the decision makers/bridge inspectors immensely.     

Effects of Edge-Stiffening Elements and Diaphragms on Bridge Resistance and Load Distribution

This research investigates the effects of barriers, sidewalks, and diaphragms (secondary elements) on bridge structure ultimate capacity and load distribution. Simple-span, two-lane highway girder bridges with composite steel and prestressed concrete girders are considered. The finite-element method is used for structural analysis. For the elastic range, typical secondary elements can reduce girder distribution factors (GDF) between 10 and 40%, depending on stiffness and bridge geometry. For the inelastic response, steel is modeled using von Mises yield criterion and isotropic (work) hardening. Concrete is modeled with a softening curve in compression with the ability to crack in tension. At ultimate capacity, typical secondary elements can reduce GDF an additional 5 to 20%, and bridge system ultimate capacity can be increased from 1.1 to 2.2 times that of the base bridge without secondary elements, depending on bridge geometry and secondary-element dimensions.     

Analytical Load Rating of an Open-Spandrel Arch Bridge: Case Study

The live load structural capacity of open-spandrel arch bridge structures is difficult to quantify. In addition to live and dead loads, geometric nonlinear effects, temperature effects, and material behavior play key roles in the design and load rating of such a structure. This paper is a case study that illustrates the effect these variables have on load rating a two-span shallow concrete arch bridge. Presented are load ratings of the structure’s arch ribs using a three-dimensional finite-element model with American Association of State Highway and Transportation Officials publications. As a result of this study, a refined analysis is recommended for load rating arch bridges.     

Field Load Tests and Numerical Analysis of Qingzhou Cable-Stayed Bridge

A field load test is an essential way to understand the behavior and fundamental characteristics of newly constructed bridges before they are allowed to go into service. The results of field static load tests and numerical analyses on the Qingzhou cable-stayed bridge (605?m central span length) over the Ming River, in Fuzhou, China are presented in the paper. The general test plan, tasks, and the responses measured are described. The level of test loading is about 80–95% of the code-specified serviceability load. The measured results include the deck profile, deck and tower displacements, and stresses of steel-concrete composite deck. A full three-dimensional finite-element model is developed and calibrated to match the measured elevations of the bridge deck. A good agreement is achieved between the experimental and analytical results. It is demonstrated that the initial equilibrium configuration of the bridge plays an important role in the finite-element calculations. Both experimental and analytical results have shown that the bridge is in the elastic state under the planned test loads, which indicates that the bridge has an adequate load-carrying capacity. The calibrated finite-element model that reflects the as-built conditions can be used as a baseline for health monitoring and future maintenance of the bridge.     

Dynamic Stress Analysis of Long Suspension Bridges under Wind, Railway, and Highway Loadings

Computation of the dynamic stress of long suspension bridges under multiloadings is essential for either the strength or fatigue assessment of the bridge. This paper presents a framework for dynamic stress analysis of long suspension bridges under wind, railway, and highway loadings. The bridge, trains, and road vehicles are respectively modeled using the finite-element method (FEM). The connections between the bridge and trains and between the bridge and road vehicles are respectively considered in terms of wheel-rail and tire-road surface contact conditions. The spatial distributions of both buffeting forces and self-excited forces over the bridge deck surface are considered. The Tsing Ma suspension bridge and the field measurement data recorded by a wind and structural health monitoring system (WASHMS) installed in the bridge are utilized as a case study to examine the proposed framework. The information on the concerned loadings measured by the WASHMS is taken as inputs for the computation simulation, and the computed stress responses are compared with the measured ones. The results show that running trains play a predominant role in bridge stress responses compared with running road vehicles and fluctuating wind loading.     

Dynamic and Impact Behavior of Half-Through Arch Bridges

The objective of this paper is to present the results of an investigation of the dynamic and impact characteristics of half-through arch bridges with rough decks caused by vehicles moving across them. Seven arch bridges modeled as three-dimensional structures with overall span lengths ranging from 20?to?200?m (65.5?to?656.2?ft) are analyzed. The American Association of State Highway and Transportation Officials Specifications HS20-44 truck is the applied vehicle loading used in the analysis and is simulated as a three-dimensional, nonlinear vehicle model with 11 degrees of freedom. Truck components include the body, suspension, and tires. The bridge deck surface is assumed to have a “good” surface roughness and is simulated using a stochastic process (power spectral density function). The effect on impact factors of span length, rise-to-span ratio, and vehicle speed is discussed. The results of the analyses show that the impact factors of bending moment and axial force will not exceed 0.4 and 0.25, respectively. The proposed impact equations are simple and conservative and can be used in the design of half-through arch bridges.     

Tests of RC Deck Girders with 1950s Vintage Details

Large numbers of conventionally reinforced concrete (CRC) bridges in the national bridge inventory built during the 1950s are lightly reinforced for shear. Inspections revealed many of these bridges exhibit diagonal cracks resulting in load postings, monitoring, emergency shoring, repairs, and unscheduled bridge replacements. A research program was conducted to investigate the behavior and capacity of CRC bridge girders with vintage details. Laboratory tests of large-size girders representative of 1950s design and construction practice were carried out. Various steel reinforcement configurations were tested. Loading conditions were varied to reproduce girder behavior at different positions in a bridge and various loading protocols were considered. Test results provide a comprehensive data set for comparison of analysis methods and repair strategies; and indicated that anchorage of flexural steel was key to developing higher ultimate capacity, initial crack damage may not necessarily contribute to the final failure mode, and crack width alone may not indicate the level of damage to the beam.     

Impact Factors for Horizontally Curved Composite Box Girder Bridges

This paper presents a method for determining the dynamic impact factors for horizontally curved composite single- or multicell box girder bridges under AASHTO truck loading. The bridges are modeled as three-dimensional structures using commercially available software. The vehicle is idealized as a pair of concentrated forces, with no mass, traveling in two circumferential paths parallel to the curved centerline of bridges. An extensive parametric study is conducted, in which over 215 curved composite box girder bridge prototypes are analyzed. The key parameters considered in this study are: Number of cells, number of lanes, degree of curvature, arc span length, slope of the outer steel webs, number and area of bracing and top chord systems, and truck(s) speed and truck(s) positioning. Based on the data generated from the parametric study, expressions for dynamic impact factors for longitudinal moment, reaction, and deflection are proposed as function of the ratio of the arc span length to the radius of curvature. The results from this study would enable bridge engineers to design horizontally curved composite box girder bridges more reliably and economically. Furthermore, the results can be used to potentially increase the live-load capacity of existing bridges to prevent posting or closing of the bridge.     

Extreme Thermal Loading on Steel Bridges in Tropical Region

In the design of highway bridges, it is important to consider the thermal stresses induced by the nonlinear temperature distribution in the bridge deck irrespective of their spans. To cope with this, design temperature profiles are provided by many bridge design codes, which are normally based on extensive research on the thermal behavior of bridges. This paper presents the results of a comprehensive investigation on the thermal behavior of steel bridges carried out in Hong Kong. A method for predicting bridge temperatures from given meteorological conditions is briefly discussed. The theoretical results have been validated by temperature measurements on experimental models mounted on the roof of a building as well as on an existing steel bridge. Both the theoretical and field results confirm the validity of the one-dimensional heat transfer model on which most design codes are based. Values of design thermal loading for a 50-year return period are determined from the statistics of extremes over 40 years of meteorological information in Hong Kong. The design temperature profiles for various types of steel bridge deck with different thickness of bituminous surfacing are developed.     

Design for Shear in Curved Composite Multiple Steel Box Girder Bridges

Modern highway bridges are often subject to tight geometric restrictions and, in many cases, must be built in curved alignment. These bridges may have a cross section in the form of a multiple steel box girder composite with a concrete deck slab. This type of cross section is one of the most suitable for resisting the torsional, distortional, and warping effects induced by the bridge’s curvature. Current design practice in North America does not specifically deal with shear distribution in horizontally curved composite multiple steel box girder bridges. In this paper an extensive parametric study, using an experimentally calibrated finite-element model, is presented, in which simply supported straight and curved prototype bridges are analyzed to determine their shear distribution characteristics under dead load and under AASHTO live loadings. The parameters considered in this study are span length, number of steel boxes, number of traffic lanes, bridge aspect ratio, degree of curvature, and number and stiffness of cross bracings and of top-chord systems. Results from tests on five box girder bridge models verify the finite-element model. Based on the results from the parametric study simple empirical formulas for maximum shears (reactions) are developed that are suitable for the design office. A comparison is made with AASHTO and CHBDC formulas for straight bridges. An illustrative example of the design is presented.     

Load Distribution for a Highly Skewed Bridge: Testing and Analysis

The American Association of State Highway and Transportation Officials (AASHTO) specifications provide formulas for determining live load distribution factors for bridges. For load distribution factors to be accurate, the behavior of the bridge must be understood. While the behavior of right-angle bridges and bridges with limited skews is relatively well understood, that of highly skewed bridges is not. This paper presents a study aimed at developing a better understanding of the transverse load distribution for highly skewed slab-on-steel girder bridges. The study involved both a diagnostic field test of a recently constructed bridge and an extensive numerical analysis. The bridge tested and analyzed is a two-span, continuous, slab-on-steel composite highway bridge with a skew angle of 60°. The bridge behavior is defined based on the field test data. Finite-element analyses of the bridge were conducted to investigate the influence of model mesh, transverse stiffness, diaphragms, and modeling of the supports. The resulting test and analytical results are compared with AASHTO’s Load and Resistance Factor Design formulas for live load distribution to assess the accuracy of the current empirical formulas.     

Dynamic Behavior of Steel Deck Tension-Tied Arch Bridges to Seismic Excitation

The dynamic responses of steel deck, tension-tied, arch bridges subjected to earthquake excitations were investigated. The 620 ft (189 m) Birmingham Bridge, located in Pittsburgh, was selected as an analytical model for the study. The bridge has a single deck tension-tied arch span and is supported by two bridge piers, which in turn are supported by the pile foundations. Due to the complex configuration of the deck system, two analytical models were considered to represent the bridge deck system. Using the normal mode method, seismic responses were calculated for two bridge models and the results were compared with each other. Three orthogonal records of the El Centro 1940 earthquake were used as input for the seismic response analysis. The modal contributions were also checked in order to obtain a reasonable representation of the response and to minimize computational cost. Displacements and stresses at the panel points of the bridge are calculated and presented in graphical form.     

Evaluation of Load Distribution Factor by Series Solution for Orthotropic Bridge Decks

In bridge engineering, the three-dimensional behavior of a bridge system is usually reduced to the analysis of a T-beam section, loaded by an equivalent fraction of the applied live load, which is called the live load distribution factor (LDF). The LDF is defined in the both the AASHTO Standard Specifications and the LRFD Specifications primarily for concrete slabs and has inherent applicable limitations. This paper provides explicit formulas using series solutions for LDF of orthotropic bridge decks, applicable to various materials but intended for fiber-reinforced polymer (FRP) decks. The present formulation considers important parameters that represent the response characteristics of the structure that are often omitted or limited in the AASHTO Specifications. A one-term series solution is proposed based on the macroflexibility approach, in which the bridge system is simplified into two major components, deck and stringers. The governing equations for the two components are obtained separately, and the deflections and interaction forces are solved by ensuring displacement compatibility at stringer lines. The LDF is calculated as the ratio of the single stringer interaction force to the summation of total stringer interaction forces. To verify this solution, a finite-element (FE) parametric study is conducted on 66 simply supported concrete slab-on-steel girder bridges. The results from the series solution correlates well with the FE results. It is also illustrated that the series solution can be applied to predict LDF for FRP deck-on-steel girder bridges, by favorable comparisons among the analytical, FE, and testing results for a one-third-scale bridge model. The scale test specimen consists of an FRP sandwich deck attached to steel stringers by a mechanical connector. The series solution is further used to obtain multiple regression functions for the LDF in terms of nondimensional variables, which can be used for simplified design purposes.