共查询到20条相似文献,搜索用时 62 毫秒
1.
采用表面为右螺纹圆柱型搅拌针的搅拌头对3mm厚LY12铝合金进行了搅拌摩擦焊搭接试验,研究了轴肩下压量对接头界面迁移和搭接接头力学性能的影响.结果表明,随轴肩下压量增大,焊缝两侧的搭接界面均向下迁移,其迁移量随下压量的增加而增加,焊缝返回侧的界面迁移量大于前进侧.控制轴肩下压量,当轴肩下压量合适时,焊缝两侧的界面仅发生较小的迁移.当焊缝两侧的界面仅发生较小的迁移量时,搭接接头有较高的抗剪强度,且断裂都发生在上板,呈正断.焊缝两侧的搭接界面向下迁移时,断裂都发生在下板,接头抗剪强度随界面迁移高度的增加而减小,且受拉侧在下板前进侧时,接头的抗剪强度较受拉侧在下板返回侧时的高. 相似文献
2.
为了研究7B04高强铝合金搅拌摩擦焊搭接接头的界面成形与力学性能,对2 mm厚薄板搭接接头进行了不同工艺参数的搅拌摩擦焊接。试验结果表明:当旋转速度和轴肩下压量不变,焊接速度在50~300 mm/min之间变化时,接头的抗拉强度先增后减;当旋转速度和焊接速度不变,轴肩下压量在0.1~0.4 mm之间变化时,接头的抗拉强度逐渐增大;当焊接速度和轴肩下压量不变,旋转速度在400~1000 r/min之间变化时,接头的抗拉强度先增后减。当旋转速度为600 r/min、焊接速度为200 mm/min、轴肩下压量为0.3 mm时,接头强度最高。 相似文献
3.
4.
5.
以0.5 mm厚LF3薄壁铝合金微搅拌摩擦焊搭接过程为研究对象,采用超小轴肩搅拌工具,研究了其无倾角微搅拌摩擦焊接过程,重点分析了微观组织分布特点和接头力学性能.采用内聚花纹锥形超小轴肩搅拌工具,依靠轴肩及搅拌针花纹的材料内聚效果,降低了焊缝宽度,焊缝宽度仅为3 mm,为微小薄壁壳体的焊接封装问题提供了可行的解决方案.搅拌工具的超高旋转频率运动,将搭接界面进行了充分的搅拌、混合和破碎,优于传统搅拌摩擦焊的Hook搭接界面.微搅拌摩擦焊搭接接头承载能力平均达到母材承载能力的89.6%. 相似文献
6.
7.
采用自行研制的无匙孔搅拌摩擦点焊方法对3mm厚AZ31B镁板和1mm厚DP600镀锌钢板异种金属进行搭接焊接(钢板在上,镁板在下),研究了其焊接工艺参数对焊点成形及力学性能的影响.通过正交试验结果分析表明:参数因素影响从主到次为:B(轴肩下压量)→A(搅拌头旋转速度)→C(搅拌针直径).在焊接时间一定时,确定了搅拌针伸出量为1.8~2.0mm、转速为1200~1500r/min、轴肩下压量为0.1~0.3mm、搅拌针直径为5.5~6.0mm时,得到的接头表面成形较好,接头剪切力均能达到7.5kN以上. 相似文献
8.
9.
针对3 mm厚6061铝合金板,进行搅拌摩擦焊工艺参数对接头成形质量与性能的方向研究。轴肩下压量主要影响接头成形,搅拌头转速和焊接速度主要影响接头质量,通过改变上述一次参数,观察并分析接头成形和抗拉强度的变化情况。结果表明,当轴肩下压量为0.2 mm时,焊缝表面成形好、缺陷少且抗拉强度高;搅拌头转速较高或焊接速度较低时,焊缝表面成形好、强度高且鱼鳞状纹路稳定、明显;当搅拌头转数为950 r/min、焊接速度为37.5 mm/min时,焊接接头成形好、抗拉强度最大,并且只有在搅拌头转速与焊接速度相匹配的条件下,才能获得高抗拉强度的焊接接头。 相似文献
10.
对3 mm厚汽车用5754铝合金板材的搅拌摩擦焊(FSW)工艺进行系统研究,研究了焊接速度、轴肩直径和搅拌针长度等工艺参数对搅拌摩擦焊接头(对接和搭接)微观组织和力学性能的影响。结果表明,随着焊接速度的提高, 5754铝合金FSW对接接头的焊核区和轴肩区的面积逐渐减小,而搅拌针区面积先增大后减小。当焊接速度为300 mm/min时, 5754铝合金FSW对接接头的强度系数达到0.975,这是因为轴肩区和搅拌针区面积相近(面积比例为0.97),增大了焊核区和热影响区界面面积。随着5754铝合金FSW搭接搅拌针长度的增加,上下板材接触面积逐渐增大,最大拉力和抗剪强度呈先降低而后提高的趋势。研究结果表明,当上板为前进侧焊接时,焊缝中产生严重隧道缺陷,最大拉力显著减小;轴肩直径由10 mm增加到12 mm时,搭接接头中轴肩区和搅拌针区的面积相近,此时微观组织中没有隧道缺陷,接头的最大拉力和抗剪强度较高。 相似文献
11.
12.
13.
14.
A. A. Babakov 《Metal Science and Heat Treatment》1967,9(10):764-770
Conclusions Highly alloyed steels and alloys are produced in conformity with GOST or technical specifications in thick and thin sheets, beams and channels, bars, hot-rolled and cold-rolled pipe, and rod. Castings are produced in the specialized plant of the Ministry of Chemical and Petroleum Machine Building.The technology of welding stainless steels and alloys is given in [15] and [16].TsNIIChERMET. Translated from Metallovedenie i Termicheskaya Obrabotka Metallov, No. 10, pp. 43–50, October, 1967. 相似文献
15.
模具渗硼工艺及其发展应用 总被引:4,自引:0,他引:4
渗硼是提高模具使用寿命的重要途径,是在金属表面形成高硬度的金属硼化层,显著提高其耐磨性,且具有良好的耐热性和耐蚀性。近年来,随着渗硼工艺逐步改进和完善,已发展了复合渗、多元共渗及低温渗硼工艺,取得了良好的经济效果。 相似文献
16.
17.
《稀有金属材料与工程》2006,23(4):23-26
结合近年来现场试验与施工实践,分析研究了中小型镍材(工业纯镍)设备与管道的特点、性能、焊接缺陷与产生原因,以及防止与消除其缺陷、优化制造施焊质量的工艺措施,并总结了若干条注意事项。 相似文献
18.
19.
20.
A. Yu. Tsivadze G. V. Ionova V. K. Mikhalko 《Protection of Metals and Physical Chemistry of Surfaces》2010,46(2):149-169
The possibility of using unique properties of lanthanides in the nanotechnology is demonstrated. The origination of linear
and nonlinear optical properties of lanthanide compounds with phthalocyanines, porphyrins, naphthalocyanines, and their analogs
in solutions and condensed state and the prospects of obtaining novel materials on their basis are discussed. Based on the
electronic structure and properties of lanthanides and their compounds, namely, optical and magnetic characteristics, electronic
and ionic conductivity, and fluctuating valence, molecular engines are classified. High-speed storage engines or memory storage
engines; photoconversion molecular engines based on Ln(II) and Ln(III); electrochemical molecular engines involving silicate
and phosphate glasses; molecular engines whose operation is based on insulatorsemiconductor, semiconductor-metal, and metal-superconductor
types of conductivity phase transitions; solid electrolyte molecular engines; and miniaturized molecular engines for medical
analysis are distinguished. It is shown that thermodynamically stable nanoparticles of Ln
x
M
y
composition can be formed by d elements of the second halves of the series, i.e., those arranged after M = Mn, Tc, and Re.
Prospects of using lanthanide superconductors in nanotechnology are considered. 相似文献