Organic light-emitting devices fabricated utilizing core/shell CdSe/ZnS quantum dots embedded in a polyvinylcarbazole

Electrical and the optical properties of organic light-emitting devices (OLEDs) fabricated utilizing core/shell CdSe/ZnS quantum dots (QDs) embedded in a polyvinylcarbazole (PVK) layer were investigated. An abrupt increase of the current density above an applied voltage of 12 V for OLEDs consisting of Al/LiF/4,7-diphenyl-1,10-phenanthroline/bis-(2-methyl-8-quinolinolate)-4-(phenylphenolato) aluminium/[CdSe/ZnS QDs embedded in PVK]/poly(3,4-ethylenedioxythiophene) and poly(styrenesulfonate)/ITO/glass substrate was attributed to the existence of the QDs. Photoluminescence spectra showed that the peaks at 390 and 636 nm corresponding to the PVK layer and the CdSe/ZnS QDs were observed. While the electroluminescence (EL) peak of the OLEDs at low voltage range was related to the PVK layer, the EL peak of the OLEDs above 12 V was dominantly attributed to the CdSe/ZnS QDs. The Commission Internationale de l’Eclairage (CIE) chromaticity coordinates of the OLEDs at high voltages were (0.581, 0.380) indicative of a red color. When the holes existing in the PVK layer above 12 V were tunneled into the CdSe/ZnS QDs, the holes occupied by the CdSe/ZnS QDs combined with the electrons in the PVK layer to emit a red color related to the CdSe/ZnS QDs.     

Traps and performance of MEH-PPV/CdSe(ZnS) nanocomposite-based organic light-emitting diodes

We report the fabrication and investigations of organic light-emitting diodes (OLEDs) using a composite made by mixing poly[2-methoxy-5(2'-ethylhexyloxy)-1,4-phenylenevinylene] (MEH-PPV) with CdSe/ZnS core/shell quantum dots (QDs). The electroluminescence efficiency of the studied devices was found to be improved as compared to devices using MEH-PPV. Moreover, the current density decreased with increasing QD concentration. We checked the effects of QDs on the electrical transport by determining the trap states, making use of the charge-based deep level transient spectroscopy (Q-DLTS) technique. The most striking result obtained is the decrease in trap density when adding QDs to the MEH-PPV polymer film. These results suggest that QDs would heal defects in nanocomposite-based devices and that CdSe/ZnS QDs prevent the trap center formation.     

Synthesis and photoluminescence of bright water-soluble CdSe/ZnS quantum dots overcoated by hybrid organic shell

Photoluminescence properties from water soluble CdSe/ZnS QDs encapsulated with hybrid trioctylphosphine-poly(acrylamide-co-acrylic acid)-ethanolamine (TOPO-PSMA-EA) shell have been investigated. It was found that PL efficiency of CdSe/ZnS QDs in water was increased 5–30% after introducing PSMA-EA polymers to encapsulate CdSe/ZnS-TOPO QDs. Higher PSMA concentrations were found to enhance the PL efficiency of QDs up to 1.8 folds, which is ascribed to a better packing and passivation of the TOPO-PSMA-EA shell over the QDs. Time-resolved photoluminescence suggested that the mean lifetime of photoexcited carriers in the water-soluble CdSe/ZnS-TOPO-PSMA-EA QDs elongated 2–17 ns compared with that of uncoated samples, indicating that PL quenching defects were effectively removed for CdSe/ZnS QDs with hybrid TOPO-PSMA-EA shell.     

Fabrication of quantum dot-sensitized solar cells with multilayer TiO2/PbS(X)/CdS/CdSe/ZnS/SiO2 photoanode and optimization of the PbS nanocrystalline layer

In this work, two multilayer photoanode structures of TiO₂/PbS(X)/CdS/ZnS/SiO₂ and TiO₂/PbS(X)/CdS/CdSe/ZnS/SiO₂ were fabricated and applied in quantum dot-sensitized solar cells (QDSCs). Then, the effect of PbS QDs layer on the photovoltaic performance of corresponding cells was investigated. The sensitization was carried out by PbS and CdS QDs layers deposited on TiO₂ scaffold through successive ionic layer adsorption and reaction (SILAR) method. The CdSe QDs film was also formed by a fast, modified chemical bath deposition (CBD) approach. Two passivating ZnS and SiO₂ layers were finally deposited by SILAR and CBD methods, respectively. It was shown that the reference cell with TiO₂/CdS/ZnS/SiO₂ photoanode demonstrated a power conversion efficiency (PCE) of 3.0%. This efficiency was increased to 4.0% for the QDSC with TiO₂/PbS(2)/CdS/ZnS/SiO₂ photoelectrode. This was due to the co-absorption of incident light by low-bandgap PbS nanocrystalline film and also the CdS QDs layer and well transport of the charge carriers. For the CdSe included QDSCs, the PbS-free reference cell represented a PCE of 4.1%. This efficiency was improved to 5.1% for the optimized cell with TiO₂/PbS(2)/CdS/CdSe/ZnS/SiO₂ photoelectrode. The maximized efficiency was enhanced about 25% and 70% compared to the PbS-free reference cells with and without the CdSe QDs layer.

     

Cytotoxicity of cadmium-containing quantum dots based on a study using a microfluidic chip

There is a lack of reliable nanotoxicity assays available for monitoring and quantifying multiple cellular events in cultured cells. In this study, we used a microfluidic chip to systematically investigate the cytotoxicity of three kinds of well-characterized cadmium-containing quantum dots (QDs) with the same core but different shell structures, including CdTe core QDs, CdTe/CdS core–shell QDs, and CdTe/CdS/ZnS core-shell-shell QDs, in HEK293 cells. Using the microfluidic chip combined with fluorescence microscopy, multiple QD-induced cellular events including cell morphology, viability, proliferation, and QD uptake were simultaneously analysed. The three kinds of QDs showed significantly different cytotoxicities. The CdTe QDs, which are highly toxic to HEK293 cells, resulted in remarkable cellular and nuclear morphological changes, a dose-dependent decrease in cell viability, and strong inhibition of cell proliferation; the CdTe/CdS QDs were moderately toxic but did not significantly affect the proliferation of HEK293 cells; while the CdTe/CdS/ZnS QDs had no detectable influence on cytotoxicity with respect to cell morphology, viability, and proliferation. Our data indicated that QD cytotoxicity was closely related to their surface structures and specific physicochemical properties. This study also demonstrated that the microfluidic chip could serve as a powerful tool to systematically evaluate the cytotoxicity of nanoparticles in multiple cellular events.     

CdSe and CdSe/ZnS quantum dots for the detection of C-reactive protein

In this study, a method for the detection of C-reactive protein (CRP) using CdSe and CdSe/ZnS quantum dots (QDs) is proposed. CdSe and CdSe/ZnS core-shell QDs are synthesised by using 2-mercaptosuccinic acid (MSA) as a capping agent. These QDs were then subjected to various characterisation studies, namely X-ray diffraction and transmission electron microscope for size and structure, Fourier transform infrared spectroscopy for the confirmation of functional groups, ultraviolet–visible absorption and fluorescence spectroscopy for optical characteristics and dynamic light scattering for hydrodynamic changes of QDs. Two biochemical mixtures were developed: one by mixing blood serum containing CRP and CdSe-phosphorylethanolamine (PEA) and the other by mixing blood serum with CdSe/ZnS-PEA. When these mixtures are observed for fluorescence due to interaction of QDs with CRP, a correlation between changes in fluorescence for different concentrations of CRP is noted. The result demonstrates that CRP can be detected with the help of QDs without using any antibodies.     

Radiative interface state study in CdSe/ZnS quantum dots covered by polymer

The paper presents the transformation of photoluminescence (PL) spectra of nonconjugated and bioconjugated core/shell CdSe/ZnS QDs covered by PEG polymer at the aging in ambient air. Studied QDs are characterized by the sizes: (i) 3.6-4.0 nm and color emission with the maxima at 560-565 nm (2.19-2.25 eV) and (ii) 5.2-5.3 nm and with emission at 605-610 nm (2.02-2.08 eV). The part of 565 nm CdSe/ZnS QDs has been bioconjugated to the mouse anti PSA (Prostate-Specific Antigen) antibodies and the part of 605 nm QDs has been bioconjugated to the antihuman IL10 (Interleukin 10) antibodies using the commercially available 565 nm and 605 nm QD conjugation kits. It is revealed that the aging process in ambient air has the very strong impact on PL spectra of nonconjugated core/shell CdSe/ZnS QDs covered with PEG polymer. The aging process relates to the polymer modification in ambient air that is accompanied by the three effects: (i) polymer transparency increasing for the emission of CdSe cores (2.03 or 2.20 eV), (ii) the intensity stimulation of high energy PL bands (2.37, 2.73 and 3.06 eV) related to the interface states at the ZnS/PEG polymer interface and (iii) the elastic strain modification in QD systems. The concentration of interface states at the ZnS/polymer interface increases at the aging of PEG polymer in ambient air.     

核壳型量子点-纳米金颗粒组装体高效检测神经性毒剂模拟剂

实验设计制备了一种由12层硫化锌包覆硒化镉的核壳型量子点(CdSe/12ZnS QDs)和纳米金颗粒(Au NPs)自组装形成的CdSe/12ZnS QDs/Au NPs复合结构, 并将其应用于神经性毒剂模拟剂氰基磷酸二乙酯(Diethyl Cyanophosphonate, DCNP)的高效检测。QDs由于与Au NPs存在荧光共振能量转移作用(Fluorescence Resonance Energy Transfer, FRET)而发生荧光猝灭, 乙酰胆碱酯酶(AChE)水解氯化硫代乙酰胆碱(ATC)生成的硫胆碱能够将量子点取代而使量子点荧光恢复。当QDs与Au NPs的摩尔浓度比为20 : 1时, QDs荧光猝灭效果最佳, AChE浓度为1.0×10 ^-3 U/L时, QDs荧光恢复效果最好。DCNP的存在会抑制AChE的活性, 减少硫胆碱的生成并降低QDs的荧光恢复效率, 通过对QDs荧光恢复效率测定能够检测DCNP。在最优条件下对DCNP的检测结果表明, 量子点的荧光恢复效率与DCNP浓度的对数在5.0×10 ^-9~5.0×10 ^-4mol/L的范围内存在良好的线性关系, 检出限达5.0×10 ^-9mol/L。     

Encapsulation of CdSe/ZnS nanocrystals within mesoporous silica spheres

Quantum dots (QDs) have attracted much attention on account of their unique optical and electronic properties. Applications of QDs in biological systems face challenges owing to their toxicity and hydrophobicity. Incorporation of QDs in mesoporous silica spheres affords not only hydrophilic shell for QDs in order to enhance their dispersion in aqueous medium, but also offers chemically inert shielding to reduce QD cytotoxicity. In the current work, two types of mesoporous silica encapsulated QDs were synthesized by rationally adjusting the reaction conditions. Mesoporous silica coated single CdSe/ZnS nanoparticles (sCdSe/ZnS@mSiO₂) were prepared through the one-pot reaction. Further modification of this reaction offered hollow mesoporous silica spheres (CdSe/ZnS@HMSS) encapsulating multiple CdSe/ZnS QDs assembled on the internal surface of the spheres. Both of sCdSe/ZnS@mSiO₂ and CdSe/ZnS@HMSS show significant photophysical properties. Possible formation mechanism of the two types of nanostructures was investigated and discussed.     

CdSe胶质量子点的电致发光特性研究

采用胶体化学法合成硒化镉(CdSe)胶质量子点, 在此基础上制成了以CdSe胶质量子点为有源层, 结构为ITO/ZnS/CdSe/ZnS/Al的电致发光(EL)器件. 透射电镜测量表明量子点的尺寸为4.3 nm, 扫描电子显微镜测量ZnS薄膜和Al薄膜结果显示表面均较为平整, 由器件结构的X射线衍射分析观察到了CdSe(111)、ZnS(111)等晶面的衍射, 表明器件中包含了CdSe量子点和ZnS绝缘层材料. 光致发光谱表征胶质量子点的室温发光峰位于614 nm, 电致发光测量得到器件在室温下的发光波长位于450 ~ 850 nm, 峰值在800 nm附近. 本文对电致发光机制及其与光致发光谱的区别进行了讨论.     

Photoluminescent, transparent and flexible di-ureasil hybrids containing CdSe/ZnS quantum dots

We describe, in this paper, the sol-gel synthesis of di-ureasil based nanocomposites prepared in situ in the presence of organically capped CdSe quantum dots (QDs) or CdSe QDs which have been coated with a ZnS shell. For the latter a new chemical route to coat the CdSe QDs with ZnS shells was investigated and is now reported. The QDs became well dispersed in the final nanocomposites, whose microstructural homogeneity was evaluated by atomic force microscopy (AFM) and transmission electron microscopy (TEM) analyses. In order to understand the optical behaviour of di-ureasil containing QDs, a detailed photoluminescent study was undertaken for a selected particle size distribution of ZnS coated CdSe QDs (d～4.5?nm). Emission quantum yields up to 0.11 were measured in the final nanocomposites that present a huge (between 3 and 6 orders of magnitude) increase in the lifetime of the QDs (relative to that of isolated ones), as a result of energy transfer occurring between the intimately mixed di-ureasil host and the QDs.     

Enhanced photovoltaic performance of solar cell based on front-side illuminated CdSe/CdS double-sensitized TiO2 nanotube arrays electrode

Free-standing TiO₂ nanotube (NT) arrays have been prepared by a two-step anodization method. These translucent TiO₂ NT arrays can be transferred to the fluorine-doped tin oxide glass substrates to form front-side illuminated TiO₂ NT electrodes. The TiO₂ NT electrodes were double-sensitized by CdSe/CdS quantum dots (QDs) through successive ionic layer adsorption and reaction (SILAR) process. The absorption range of the TiO₂ NT electrode was extended from ~380 to 700 nm after sensitization with CdSe/CdS QDs. The SILAR cycles were investigated to find out the best combination of CdS and CdSe QDs for photovoltaic performance. The power conversion efficiency of 2.42 % was achieved by the CdSe(10)/CdS(8)/TiO₂ NT solar cell. A further improved efficiency of 2.57 % was obtained with two cycles of ZnS overlayer on the CdSe(10)/CdS(8)/TiO₂ NT electrode, which is 45.19 % higher than that of back-side illuminated solar cell. Furthermore, the ZnS(2)/CdSe(10)/CdS(8)/TiO₂ NT solar cell possesses a higher stability than CdSe(10)/CdS(8)/TiO₂ NT solar cell during the same period. The better photovoltaic performance of the ZnS(2)/CdSe(10)/CdS(8)/TiO₂ NT solar cell has demonstrated the promising value to design quantum dots-sensitized solar cells with double-sensitized front-side illuminated TiO₂ NT arrays strategy.     

在多相体系中制备核壳型CdSe/ZnS量子点

在多相体系中制得了CdSe/ZnS半导体量子点,采用X射线粉末衍射(XRD)、电子透射显微镜(TEM)等测试手段对产物进行了表征,结果表明CaSe/CdS量子点尺寸均一、形貌规则,具有立方晶体结构.初步研究了此体系的反应机理,并通过紫外-可见吸收光谱和荧光光谱对产物的光学性质进行了分析,结果表明在CASe量子点外面包覆一定厚度的ZnS壳层后,其激子发射强度和量子效率显著提高.     

Quantum dot encapsulation in viral capsids

Incorporation of CdSe/ZnS semiconductor quantum dots (QDs) into viral particles provides a new paradigm for the design of intracellular microscopic probes and vectors. Several strategies for the incorporation of QDs into viral capsids were explored; those functionalized with poly(ethylene glycol) (PEG) can be self-assembled into viral particles with minimal release of photoreaction products and enhanced stability against prolonged irradiation.     

Photoluminescence-enhanced biocompatible quantum dots by phospholipid functionalization

A simple two-step strategy using phospholipid (PPL) to functionalize core/shell CdSe/ZnS quantum dots (QDs) has been described. The experimental data show that the use of S-H terminated PPL results not only in the high colloidal stability of core/shell CdSe/ZnS QDs in the aqueous phase, but also in the significant enhancement of photoluminescence. The degree of the enhancement is a function of the PPL-CdSe/ZnS QDs sample concentration. These results might be promising for future biological platform in new devices ranging from photovoltaic cells to biosensors and other devices.     

Synergistic effects of SPR and FRET on the photoluminescence of ZnO nanorod heterostructures

Solution-grown ZnO nanorods (NRs) were successfully conjugated with CdSe/ZnS quantum dots (QDs) and Ag nanoparticles (NPs) to suppress intrinsic defect emission and to enhance band-edge emission at the same time. First, high-density and high-crystallinity ZnO NRs of diameter 80–90 nm and length 1.2–1.5 μm were grown on glass substrates using a low-temperature seed-assisted solution method. The as-synthesized ZnO NRs showed sharp photoluminescence (PL) band-edge emission centered at ～377 nm together with broad defect emission in the range of ～450–800 nm. The ZnO NRs were decorated with CdSe/ZnS QDs and Ag NPs, respectively, by sequential drop-coating. The PL of CdSe/ZnS QD||ZnO NR conjugates showed that ZnO band-edge emission decreased by 73.8% due to fluorescence resonance energy transfer (FRET) and charge separation between ZnO and CdSe/ZnS by type II energy band structure formation. On the other hand, Ag NP||CdSe/ZnS QD||ZnO NR conjugates showed increased band-edge emission (by 25.8%) and suppressed defect emission compared to bare ZnO NRs. A possible energy transfer mechanism to explain the improved PL properties of ZnO NRs was proposed based upon the combined effects of FRET and surface plasmon resonance (SPR).     

Photoluminescence of colloidal CdSe/ZnS quantum dots under oxygen atmosphere

The effects of oxygen versus vacuum ambients on colloidal CdSe/ZnS quantum dots (QDs) were studied using both continuous and time-resolved photoluminescence (PL) measurements. The PL intensities were found to be an order of magnitude higher in an oxygen atmosphere, which is explained by the passivation of surface defects by oxygen absorption. The decay of PL intensities can be best fitted by a biexponential function with lifetimes of approximately 1 ns for the fast decay and approximately 10 ns for the slow decay. Based on the emission-energy dependence of carrier lifetimes and of the amplitude ratio of the fast-decay component to the slow-decay component, we suggest that the fast and slow PL decay of colloidal CdSe/ZnS QDs is caused by the recombination of delocalized carriers in the internal core states and the localized carriers in the surface states, respectively.     

Structural characterization of CdSe/ZnS core–shell quantum dots (QDs) using TEM/STEM observation

CdSe/ZnS core–shell structured nano-crystal quantum dots (QDs) are ideal candidates for light-emission applications due to their high quantum efficiency, narrow-band, and particle-size-tunable photoluminescence. In particular, their small size results in the quantum confinement of semiconductor nano-crystals, which widens their energy gaps. In general, structural analyses of QDs using a transmission electron microscope (TEM) are very important due to the significantly small size of QDs. We were able to obtain structural information of CdSe/ZnS core–shell QDs using nano-beam diffraction by controlling the nano-probe of the dark field scanning TEM (DF-STEM) mode and strain analysis with high-resolution TEM (HRTEM)/STEM images. Furthermore, we could clearly distinguish the interface between the CdSe core and the ZnS shell from the strain analysis with the HRTEM/STEM images.     

Toxicity of CdTe Quantum Dots on Yeast Saccharomyces Cerevisiae

Along with the widespread development of their bioapplications, concerns about the biosafety of quantum dots (QDs) have increasingly attracted intensive attention. This study examines the toxic effect and subcellular location of cadmium telluride (CdTe) QDs with different sizes against yeast Saccharomyces cerevisiae. The innovative approach is based on the combination of microcalorimetric, spectroscopic, electrochemical, and microscopic methods, which allows analysis of the toxic effect of CdTe QDs on S. cerevisiae and its mechanism. According to the values of the half inhibitory concentration (IC(50) ), CdTe QDs exhibit marked cytotoxicity in yeast cells at concentrations as low as 80.81 nmol L(-1) for green-emitting CdTe QDs and 17.07 nmol L(-1) for orange-emitting CdTe QDs. QD-induced cell death is characterized by cell wall breakage and cytoplasm blebbing. These findings suggest that QDs with sizes ranging from 4.1 to 5.8 nm can be internalized into yeast cells, which then leads to QD-induced cytotoxicity. These studies provide valuable information for the design and development of aqueous QDs for biological applications.     

Shell distribution on colloidal CdSe/ZnS quantum dots

Scanning transmission electron microscopy (STEM) coupled with electron energy loss spectroscopy (EELS) was used to determine the chemical distribution of semiconductor shell material around colloidal core-shell CdSe/ZnS quantum dots (QDs). EELS signals from positions around the QD indicate a well-defined shell of ZnS surrounding the CdSe core, but the distribution of the shell material is highly anisotropic. This nonuniformity may reflect the differences in chemical activity of the crystal faces of the core QD and implies a nonoptimal QD surface passivation.