Determination of Cu2+ using poly(2-aminothiazole)/ multi-walled carbon nanotubes composite film modified glassy carbon electrodes

2-Aminothiazole was electropolymerized by cyclic voltammetry (CV) on the multi-walled carbon nanotubes (MWCNTs) modified glassy carbon electrode (GCE) surface. Poly(2-aminothiazole)/MWCNTs/GCE was used for determination of copper ions. The anodic peak currents of copper ions evaluated by differential pulse stripping voltammetry (DPSV) are linear with the concentrations in the range from 1.0 x 10(-7) M to 2.0 x 10(-5) M with a linear coefficiency of 0.9985. The detection limit is 2.0 x 10(-9) M calculated for a signal-to-noise ratio of 3 (S/N = 3). The proposed method was applied successfully to the determination of copper ions in drinking water, and the recovery was 96%.     

Determination of serotonin on a glassy carbon electrode modified by electropolymerization of meso-tetrakis(2-aminophenyl)porphyrin and single walled carbon nanotubes

A chemically modified electrode [poly(TAPP)-SWNT/GCE] was prepared by electropolymerization of meso-tetrakis(2-aminophenyl)porphyrin (TAPP)-single walled carbon nanotubes (SWNT) on the surface of a glassy carbon electrode (GCE). This modified electrode was employed as an electrochemical biosensor for the determination of serotonin concentration and exhibited a typical enhance effect on the current response of serotonin and lower oxidation overpotential. The biosensor was very effective to determined 5-HT in a mixture. The linear response was in the range 2.0 x 10(-7) to 1.0 x 10(-5) M, with a correlation coefficient of 0.999 [i(p)(microA) = 3.406 C (microM)+0.132] on the anodic current, with a detection limit of 1 x 10(-9) M. Due to the relatively low currents and different potentials in the electrochemical responses to ascorbic acid and dopamine, the modified electrode is a useful and effective sensing device for the selective and sensitive serotonin determination in the presence of ascorbic acid and dopamine.     

Determination of pentachlorophenol at carbon nanotubes modified electrode incorporated with beta-cyclodextrin

A facile and reliable electrochemical technique at beta-cyclodextrin incorporated carbon nanotubes modified glassy carbon electrode (beta-CD/CNTs/GCE) was proposed for determination of pentachlorophenol (PCP). The electrochemical behavior of PCP at the beta-CD/CNTs/GCE was investigated by cyclic voltammetry and linear sweep voltammetry. The beta-CD/CNTs/GCE showed good analytical performance characteristics in electrocatalytic oxidation of PCP, compared with the simple carbon nanotube modified electrode (CNTs/GCE) and bare glassy carbon electrode (GCE). After accumulation for 5 min on beta-CD/CNTs/GCE, the peak current increased linearly with the concentration of PCP in the range from 8.0 x 10(-7) to 1.04 x 10(-5) mol/L. The detection limit was 4.0 x 10(-8) mol/L at 3 sigma level. The proposed electrode presented good repeatability for the determination of PCP in artificial wastewater, and the recovery was 97%-103%. This modified electrode combined the advantages of carbon nanotubes and supramolecular cyclodextrin, leading to new capabilities for electrochemical detection of PCP.     

Fabrication of nano-porous hydroxyapatite modified electrode and its application for determination of p-chlorophenol

Nano-porous hydroxyapatite (HAp) modified electrode was fabricated by simply electrodepositing HAp onto the glassy carbon electrode (GCE) from the electrolytes solution containing Ca(NO3)2 4H2O and NH4H2PO4, the resulting electrode (nano-HAp/GCE) was characterized with scanning electron microscopy (SEM). The electrochemical behavior of p-chlorophenol (p-CP) at nano-HAp/GCE was studied by cyclic voltammetry. The electrode displayed selective and enhanced electroanalytical response towards p-CP, obviously because p-CP is accumulated at the electrode. For the greater sensitivity, a semi-derivative technique was adopted to obtain the current signal. The results indicated that the nano-HAp/GCE exhibits substantial enhancement in electrochemical sensitivity for p-CP due to its large surface area and particular adsorbability. After accumulation of 4 min for p-CP on nano-HAp/GCE, the peak height was linearly related to the concentration of p-CP in the range of 1.0 x 10(-8) to 1.0 x 10(-7) mol L(-1). The detection limit was 4.0 x 10(-9) mol L-(1) at 3sigma level. Based on this, the modified electrode was successfully applied in water samples with low cost and high sensitivity.     

Carbon fiber nanoelectrodes modified by single-walled carbon nanotubes

Microelectrode voltammetry has been considered to be a powerful technique for single biological cell analysis and brain research. In this paper, we have developed a simple method to get highly sensitive carbon fiber nanoelectrodes (CFNE) modified by single-walled carbon nanotubes (SWNTs) on the basis of our previous work. The electrochemical behavior of SWNTs/CFNE was characterized by potassium ferricyanide, dopamine (DA), epinephrine (E), and norepinephrine (NE) using cyclic voltammetry (CV). Compared with CFNE, SWNTs/CFNE has a much larger available internal surface area per external geometric area, which is supported by SEM images. The modified electrodes show very high sensitivity and favorable electrochemical behavior toward these neurotransmitters. The peak current increases linearly with the concentration of DA, E, and NE in the range of 1.0 x 10(-)(7)-1.0 x 10(-)(4), 3.0 x 10(-)(7)-1.0 x 10(-)(4), and 5.0 x 10(-)(7)-1.0 x 10(-)(4) M, respectively. The CV detection limit (S/N = 3) of DA, E, and NE is 7.7 x 10(-)(9), 3.8 x 10(-)(8), and 4.2 x 10(-)(8) M, respectively. The modified electrode exhibited almost the same electrochemical behavior after 15 days, indicating that SWNTs/CFNE is pretty stable and has good reproducibility.     

MnO2纳米棒-还原石墨烯复合修饰玻碳电极用于苋菜红的检测

利用电化学还原法制备MnO₂纳米棒-还原石墨烯复合修饰电极（MnO₂ NRs-ErGO/GCE）用于苋菜红的检测。采用SEM和XRD分别对修饰电极材料进行微观形貌和成分结构表征。通过循环伏安法考察了苋菜红在裸电极、ErGO/GCE和MnO₂ NRs-ErGO/GCE上的电化学行为,并对测定条件如pH值、富集电位、富集时间进行了优化。结果表明,MnO₂ NRs-ErGO增大了GCE电化学活性面积,提高了苋菜红的电化学氧化响应。在最优的检测条件下,MnO₂ NRs-ErGO/GCE线性扫描伏安法检测苋菜红线性范围为2.0×10^-8~1.0×10^-5 mol/L和1.0×10^-5~4.0×10^-4 mol/L,检测限为1.0×10^-8 mol/L。MnO₂ NRs-ErGO/GCE用于真实饮料样品检测,获得满意结果。     

2D-titanium carbide (MXene) based selective electrochemical sensor for simultaneous detection of ascorbic acid,dopamine and uric acid

Two-dimensional (2D) titanium carbide (MXene) nanosheets exhibited excellent conductivity,flexibility,high volumetric capacity,hydrophilic surface,thermal stability,etc.So,it has been exploited in various applications.Herein,we report synthesis of mixed phase 2D MXene as a catalytic material for simultaneous detection of important biomolecules such as ascorbic acid (AA),dopamine (DA) and uric acid (UA),Crystalline structure,surface morphology and elemental composition of mixed phase titanium carbide (Ti-C-Tx) MXene (Tx =-F,-OH,or-O) nanosheets were confirmed by X-ray diffraction (XRD),Raman spectroscopy,high-resolution transmission electron microscopy (HR-TEM),high-resolution scanning electron microscopy (HR-SEM) and Energy-dispersive X-ray spectroscopy (EDS) mapping analysis.Furthermore,Ti-C-Tx modified glassy carbon electrode (GCE) was prepared and its electrochemical properties are studied by cyclic voltammetry (CV) and differential pulse voltammetry (DPV).It was found that Ti-C-Tx modified GCE (Ti-C-Tx/GCE) showed excellent electrocatalytic activity and separated oxidation peaks of important biomolecules such as AA (at 0.01 V),DA (at 0.21 V) and UA (at 0.33 V).Also,Ti-C-Tx/GCE sensor is enabled their simultaneous detection in physiological pH from 100 to 1000 μM for AA,0.5-50 μM for DA and 0.5-4 μM & 100-1500 μM for UA.The limit ofdetection's (LOD) was estimated as 4.6 μM,0.06 μM and 0.075 μM for AA,DA and UA,respectively.Moreover,real sample analysis indicated that spiked AA,DA and UA can be determined accurately by Ti-C-Tx/GCE with the recovery ratio in the range between 100.5％-103％ in human urine samples.The proposed Ti-C-Tx modified electrode exhibited good stability,selectivity and reproducibility as an electrochemical sensor for the detection ofAA,DA and UA molecules.     

Characterization of an EDTA bonded conducting polymer modified electrode: its application for the simultaneous determination of heavy metal ions

An EDTA bonded conducting polymer modified electrode (EDTA-CPME) was fabricated by polymerization of 3',4'-diamino-2,2';5',2'-terthiophene monomer on a GCE, followed by the reaction with EDTA in the presence of catalyst. The surface of the resulting modified electrode was characterized with EQCM, ESCA, SEM, Auger electron spectroscopy, scanning Auger microscopy, and electrochemical methods. The amounts of polymer and EDTA attached on the polymer film were determined. Simple immersing of the EDTA-CPME into a sample solution led to the chemical deposition through the complexation with Pb2+, Cu2+, and Hg2+ ions, simultaniously. Various experimental parameters that affect the simultaneous analysis of the metal ions, e.g., EDTA amount, pH, deposition time, and deposition temperature, were optimized. Calibration plots for the EDTA-CPME with square wave voltammetry were obtained in the concentration range between 5.0 x 10(-10) and 1.0 x 10(-7) M for Cu(II) and between 7.5 x 10(-10) and 1.0 x 10(-7) M for Pb(II) and Hg(II). The detection limits for Pb(II), Cu(II), and Hg(II) ions were determined to be about 6.0 x 10(-10), 2.0 x 10(-10), and 5.0 x 10(-10) M, respectively. Interference effects from other metal ions were studied at various pHs and it was found that there was little or no effect on the simultaneous determination. The stability of the EDTA-CPME was remarkably improved by coating the surface with the Nafion film, and the electrode can be used for more than one month. Analytical availability of the EDTA-CPME was demonstrated by the application for the certified standard urine reference material and tap water.     

Fabrication, characterization, and potential application of carbon fiber cone nanometer-size electrodes

A novel method has been developed for the fabrication of carbon fiber cone nanometer-size ultramicroelectrodes (nanoelectrodes) with overall tip dimensions as small as 50 nm in diameter. In this method, carbon fibers were initially etched by an argon ion beam thinner. Afterward, a single etched carbon fiber was inserted into a glass capillary, which was then sealed by heating the glass/fiber interface in a vacuum; thus, no epoxy resin is involved. The success rate of our fabrication route for the electrodes with overall tip diameters of up to 500 nm was about 80%; for those with tip diameters of up to 100 nm, it was about 50%. The fabricated carbon fiber cone nanoelectrodes (CFCNEs) were inspected by optical and scanning electron microscopy. Their electrochemical behavior was examined by cyclic and linear sweep voltammetric measurements of ferricyanide and ferrocene ions in aqueous and nonaqueous media. The potential analytical applicability of the CFCNEs was tested by differential pulse voltammetric measurements of two well-known neurotransmitters, dopamine (DA) and 5-hydroxytryptamine (5-HT), and the results achieved were highly satisfactory. The calibration plots obtained were linear over the ranges from 5.0 × 10(-7) to 1.0 × 10(-4) and from 2.0 × 10(-6) to 1.0 × 10(-4) mol/L, with limits of detection of 1.0 × 10(-7) and 5.0 × 10(-7) mol/L for DA and 5-HT, respectively. Some advantages and improvements of the proposed CFCNE fabrication method, especially with respect to smoothness of the fiber (electrode) surface, strength, and control over the fiber tip dimensions, are also discussed.     

Direct electrochemistry of cytochrome c at a glassy carbon electrode modified with single-wall carbon nanotubes

The electrochemistry of horse heart cytochrome c was studied by cyclic voltammetry at a glassy carbon electrode modified with single-wall carbon nanotubes (SWNTs). A pair of well-defined redox waves was obtained in cytochrome c aqueous solution at an activated SWNT film-modified electrode. The optimal conditions for activating the SWNT film-modified electrode has been determined. The electrode reaction of cytochrome c is a diffusion-controlled process. The peak current increases linearly with the concentration of cytochrome c in the range from 3.0 x 10(-5)-7.0 x 10(-4) M. The detection limit is 1.0 x 10(-5) M. The activated SWNT film was characterized by scanning electron microscopy. Furthermore, interaction of cytochrome c with adenine was characterized by electrochemical and spectral methods.     

Conducting polymer‐coated, palladium‐functionalized multi‐walled carbon nanotubes for the electrochemical sensing of hydroxylamine

Electrochemical sensors of hydroxylamine were fabricated on glassy carbon electrodes (GCEs) by the electropolymerization of 3,4‐ethylenedioxypyrrole (EDOP) and 3,4‐ethylenedioxythiophene (EDOT) on palladium (Pd) nanoparticles attached to thiolated multi‐walled carbon nanotubes (MWCNTs), denoted as PEDOP/MWCNT‐Pd/GCE and PEDOT/MWCNT‐Pd/GCE. The sensors were characterized by field emission scanning electron microscopy and electrochemical impedance spectroscopy. They showed strong catalytic activity toward the oxidation of hydroxylamine. Cyclic voltammetry and amperometry were used to characterize the sensors' performances. The detection limits of hydroxylamine by PEDOP/MWCNT‐Pd/GCE and PEDOT/MWCNT‐Pd/GCE were 0.22 and 0.24 μM (S/N = 3), respectively. The sensors' sensitivity, selectivity, and stability were also investigated.     

Electrochemical biosensor based on multi-walled carbon nanotubes and Au nanoparticles synthesized in chitosan

A new biosensor is prepared by cross-linking glucose oxidase (GOD) with glutaradehyde at the electrode combining Au nanoparticles (AuNP) with multi-walled carbon nanotubes (MWCNTs). Au nanoparticles-doped chitosan (CS) solution (AuNP-CS) is prepared by treating the CS solution followed by chemical reduction of Au (III) with NaBH4. MWCNTs are then dispersed in AuNP-CS solution. TEM, FT-IR, and UV-Vis show that the AuNP-CS solution is highly dispersed and stable. The synergistic effect between AuNP and CNTs of the AuNP-CNTs-CS material has been investigated by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and amperometric methods. The modified glassy carbon electrode (GCE) allows low-potential detection of H2O2 with high sensitivity and fast response time. With the immobilization of GOD, a biosensor has been constructed. In phosphate buffer solutions (PBS, pH 7.0), nearly free interference determination of glucose has been realized at 0.4 V(vs. Ag/AgCl/3.0 M KCI) with a wide linear range from 2.0 x 10(-5) to 1.5 x 10(-2) M and a fast response time within 5s. The biosensor has been used to determine glucose in human serum samples and the results are satisfactory.     

纳米TiO2/还原石墨烯复合修饰电极用于食品中 柠檬黄的检测

为了检测食品中柠檬黄的含量,利用滴涂法和电化学还原法制备纳米TiO_2/还原石墨烯复合修饰玻碳电极(TiO_2-Er GO/GCE)。采用透射电子显微镜和X射线粉末衍射仪对TiO_2和TiO_2-GO两种修饰电极材料进行表征;通过循环伏安法观察了柠檬黄在不同电极上的电化学行为,并对检测条件如p H值、富集电位、富集时间进行了优化。实验结果表明:TiO_2-Er GO/GCE增大了电极的电化学活性面积,提高了柠檬黄的电化学氧化响应;最优的检测条件为p H值为3.7、富集电位为-0.20 V、富集时间为180 s;在最优的检测条件下,采用线性扫描伏安法检测柠檬黄的线性范围为2.0×10-8~2.0×10-5 mol/L,检测限为8.0×10-9 mol/L(信噪比为3)。     

Voltammetric determination of ethamsylate in bulk solution and pharmaceutical tablet by nano-material composite-film coated electrode

A sensitive electrochemical method was described for voltammetric determination of ethamsylate at a glassy carbon electrode (GCE) coated with a nano-material thin film. In this work, a nanometer material, namely, multi-wall carbon nanotubes (MWCNT) was dispersed successfully into water in the presence of dihexadecyl hydrogen phosphate (DHP) and a MWCNT–DHP composite film was conveniently obtained on the GCE surface. The electrochemical behavior of ethamsylate at this modified electrode was investigated and a pair of reversible redox peak was observed. Compared with the electrochemical response of ethamsylate at the bare GCE, the separation of peak potential (ΔE_p) of ethamsylate decreased obviously from 438 to 40 mV and the current density of redox peaks increased greatly. Based on this, differential pulse voltammetry (DPV) was employed to determine ethamsylate. Various experimental parameters such as pH value of the supporting electrolyte, the amount of modifier and so on were optimized. Under optimal conditions, a linear response of ethamsylate was obtained in the range from 1.0 × 10^− 6 to 2.0 × 10^− 5 mol/L, and the detection limit was 6.0 × 10^− 7 mol/L. The proposed method was successfully applied to detect ethamsylate in pharmaceutical samples.     

A reduced graphene oxide based electrochemical biosensor for tyrosine detection

In this paper, a 'green' and safe hydrothermal method has been used to reduce graphene oxide and produce hemin modified graphene nanosheet (HGN) based electrochemical biosensors for the determination of l-tyrosine levels. The as-fabricated HGN biosensors were characterized by UV-visible absorption spectra, fluorescence spectra, Fourier transform infrared spectroscopy (FTIR) spectra and thermogravimetric analysis (TGA). The experimental results indicated that hemin was successfully immobilized on the reduced graphene oxide nanosheet (rGO) through π-π interaction. TEM images and EDX results further confirmed the attachment of hemin on the rGO nanosheet. Cyclic voltammetry tests were carried out for the bare glass carbon electrode (GCE), the rGO electrode (rGO/GCE), and the hemin-rGO electrode (HGN/GCE). The HGN/GCE based biosensor exhibits a tyrosine detection linear range from 5?×?10(-7)?M to 2?×?10(-5)?M with a detection limitation of 7.5?×?10(-8)?M at a signal-to-noise ratio of 3. The sensitivity of this biosensor is 133 times higher than that of the bare GCE. In comparison with other works, electroactive biosensors are easily fabricated, easily controlled and cost-effective. Moreover, the hemin-rGO based biosensors demonstrate higher stability, a broader detection linear range and better detection sensitivity. Study of the oxidation scheme reveals that the rGO enhances the electron transfer between the electrode and the hemin, and the existence of hemin groups effectively electrocatalyzes the oxidation of tyrosine. This study contributes to a widespread clinical application of nanomaterial based biosensor devices with a broader detection linear range, improved stability, enhanced sensitivity and reduced costs.     

Fabrication of multi-wall carbon nanotube film on glassy carbon electrode surface and the determination of tyrosine

A novel chemically modified electrode has been prepared on the basis of the attachment of multi-wall carbon nanotubes (MWNT) onto the surface of a glassy carbon electrode (GCE) in the presence of a hydrophobic surfactant, dihexadecyl phosphate (DHP). This MWNT film was characterized by transmission electron microscopy images (TEM) and scanning electron microscopy (SEM). The electrochemical behavior of tyrosine at the MWNT film coated GCE was examined and it is found that this MWNT-modified GCE greatly enhances the oxidation peak current of tyrosine. Effects of some important factors, including pH, scan rate and amount of modifier, on the oxidation process of tyrosine were investigated. When the signal to noise ratio (SNR) is 3, the detection limit is 1 x 10(-7) M. The low relative standard deviations of the detection of tyrosine in human morning urine (3.3%) and white wine (5.2%) suggest a good reproducibility of the modified electrode.     

Electrocatalytic detection of NADH and glycerol by NAD(+)-modified carbon electrodes

The electrochemical oxidation of the adenine moiety in NAD+ and other adenine nucleotides at carbon paste electrodes gives rise to redox-active products which strongly adsorb on the electrode surface. Carbon paste electrodes modified with the oxidation products of NAD+ show excellent electrocatalytic activity toward NADH oxidation, reducing its overpotential by about 400 mV. The rate constant for the catalytic oxidation of NADH, determined by rotating disk electrode measurements and extrapolation to zero concentration of NADH, was found to be 2.5 x 10(5) M-1 s-1. The catalytic oxidation current allows the amperometric detection of NADH at an applied potential of +50 mV (Ag/AgCl) with a detection limit of 4.0 x 10(-7) M and linear response up to 1.0 x 10(-5) M NADH. These modified electrodes can be used as amperometric transducers in the design of biosensors based on coupled dehydrogenase enzymes and, in fact, we have designed an amperometric biosensor for glycerol based on the glycerol dehydrogenase (GlDH) system. The enzyme GlDH and its cofactor NAD+ were co-immobilized in a carbon paste electrode using an electropolymerized layer of nonconducting poly(o-phenylenediamine) (PPD). After partial oxidation of the immobilized NAD+, the modified electrode allows the amperometric detection of the NADH enzymatically obtained at applied potential above 0 V (Ag/AgCl). The resulting biosensor shows a fast and linear response to glycerol within the concentration range of 1.0 x 10(-6)-1.0 x 10(-4) M with a detection limit of 4.3 x 10(-7) M. The amperometric response remains stable for at least 3 days. The biosensor was applied to the determination of glycerol in a plant-extract syrup, with results in good agreement with those for the standard spectrophotometric method.     

A method for the fabrication of low-noise carbon fiber nanoelectrodes

A new and facile method has been developed for the fabrication of low-noise carbon fiber microelectrodes (CFMEs) and carbon fiber nanoelectrodes (CFNEs). The carbon fiber was flame-fuse sealed in the tip of the glass capillary. The CFMEs were made by cutting the protruding carbon fiber to the desired length, and the CFNEs were achieved by etching the protruding carbon on the flame to form a nanometer-scale tip. The tip of CFNEs can be controlled within the range from 100 to 300 nm. Thus, no epoxy wax was involved in the CFMEs and CFNEs. The experimental results of inspecting CFMEs and CFNEs by scanning electron microscopy demonstrated that the surface of the electrodes and the glass/fiber interface are very smooth. Therefore, the noise caused by the glass/fiber of these electrodes is much lower than that of the electrodes fabricated conventionlly. The electrodes were characterized by ferricyanide, catecholamine (dopamine,DA), norepinephrine (NE), and epinephrine (E)) and 5-hydroxytryptamine (5-HT) neurotransmitters using CV, LSV, DPV, and FSCV. The results showed that the CFMEs and CFNEs have very excellent electrochemical behavior and high sensitivity. The CV and DPV detection limits of DA, NE, and E are 7.6 x 10(-8), 7.0 x 10(-8), and 5.0 x 10(-8) mol/L, and the DPV detection limits of DA, NE, and E are 4.0 x 10(-8), 1.0 x 10(-7), and 2.2 x 10(-7) mol/L, respectively. This experiment offers a new and facile method for the fabrication of CFMEs and CFNEs of very high sensitivity and low noise.     

Polyeugenol-modified platinum electrode for selective detection of dopamine in the presence of ascorbic Acid

A platinum electrode was modified with electropolymerized films of 4-allyl-2-methoxyphenol (eugenol) by its oxidative polymerization from an alkaline solution by cyclic voltammetry. The modified electrode was than used to determine dopamine (DA) in an excess of ascorbic acid (AA) by differential pulse voltammetry. The peak positions as well as relative sensitivity DA/AA were affected by the potential window applied for the polymerization. For polymerization between 0 and 2.2 V, the peak potentials recorded in a phosphate buffer solution (pH 7.4) were -61 and +152 mV vs Ag/AgCl for AA and DA, respectively. After a 5-min equilibration, relative sensitivity DA/AA was 164 and the current sensitivity for DA was 7.9 nA μM(-)(1). The detection limit for S/N = 3 is 0.1 μM. The high selectivity and sensitivity for DA was found to be due to charge discrimination/analyte accumulation and an effect of catalytic mediation of redox sites. Chronocoulometric data reveal that DA is accumulated on the electrode as a monolayer. The electrode is stable, reversible, and free of fouling problems.     

Voltammetric determination of tryptophan at a single-wall carbon nanotubes modified electrode

A single-wall carbon nanotubes (SWNT)-film coated glassy carbon electrode (GCE) was described for the determination of tryptophan. In pH 2.5 Na2HPO4-citric acid buffer, tryptophan yields a well-defined and very sensitive oxidation peak at about 1.08 V at the SWNT-film coated GCE. The oxidation peak current increases greatly and the peak potential shifts toward more negative direction at the SWNT-modified GCE in contrast to that at the bare GCE. Under optimized conditions, the oxidation peak current is proportional to the concentration of tryptophan over the range from 4 x 10(-8) to 1 x 10(-5) mol/L. The detection limit is 1 x 10(-8) mol/L at 3 min of accumulation. Using the proposed method, tryptophan in the human's blood serum samples was determined.