Efficient and non-hysteresis CH3NH3PbI3/PCBM planar heterojunction solar cells

Highly efficient and non-hysteresis organic/perovskite planar heterojunction solar cells was fabricated by low-temperature, solution-processed method with a structure of ITO/PEDOT:PSS/CH₃NH₃PbI₃/PCBM/Al. The high-quality perovskite thin film was obtained using a solvent-induced-fast-crystallization deposition involving spin-coating the CH₃NH₃PbI₃ solution followed by top-dropping chlorobenzene with an accurate control to induce the crystallization, which results in highly crystalline, pinhole-free, and smooth perovskite thin film. Furthermore, it was found that the molar ratio of CH₃NH₃I to PbI₂ greatly influence the properties of CH₃NH₃PbI₃ film and the device performance. The equimolar or excess PbI₂ was facile to form a flat CH₃NH₃PbI₃ film and produced relatively uniform perovskite crystals. Perovskite solar cells (PSCs) with high-quality CH₃NH₃PbI₃ thin film showed good performance and excellent repeatability. The power conversion efficiency (PCE) up to 13.49% was achieved, which is one of the highest PCEs obtained for low-temperature, solution-processed planar perovskite solar cells based on the structure ITO/PEDOT:PSS/CH₃NH₃PbI₃/PC₆₁BM/Al. More importantly, PSCs fabricated using this method didn’t show obvious hysteresis under different scan direction and speed.     

Improving efficiency of planar hybrid CH3NH3PbI3−xClx perovskite solar cells by isopropanol solvent treatment

Hybrid organic/inorganic perovskite planar heterojunction (PHJ) solar cells are becoming one of the most competitive emerging technologies. Here, the devices (ITO/PEDOT:PSS/CH₃NH₃PbI_3−xCl_x/PC₆₀BM/C₆₀/Al) are fabricated based on solution process. A power conversion efficiency (PCE) up to 13.1% was obtained after isopropanol (IPA) solvent treatment, which was 9% improvement than that of the original devices. Photocurrent hysteresis could be reduced to a certain extent by introducing IPA treatment. Solvent treatment can remove as-grown impurities like CH₃NH₃I and defects formed during the device fabrication. We also demonstrated the electrical and optical properties of perovskite films were improved. The addition of IPA-treated facilitates the formation of a relatively smooth PC₆₀BM films. This work provides a very simple but effective strategy to enhance the power conversion efficiency of perovskite solar cells.     

Improved performance of perovskite solar cells with a TiO2/MoO3 core/shell nanoparticles doped PEDOT:PSS hole-transporter

We demonstrate improved performance of inverted planar heterojunction CH₃NH₃PbI_3-xCl_x perovskite solar cells with a TiO₂/MoO₃ core/shell nanoparticles (NPs) doped poly(3,4-ethylene dioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS) hole-transporting layer (HTL). TiO₂/MoO₃ Core/shell NPs with size of approximately 40 nm are successfully prepared with a simple wet solution method and are interspersed into PEDOT: PSS layer to construct the HTL. The optimized device shows a high power conversion efficiency of 13.63%, which is dramatically improved compared with the reference device with a pristine PEDOT:PSS HTL. The improvement is mainly attributed to the increased crystalline of the CH₃NH₃PbI_3-xCl_x film with large-scale domains and a compact morphology. More interesting, the cells exhibit superior stability in ambient conditions, which is attributed to the inhibited penetration of moisture due to the compact morphology of the CH₃NH₃PbI_3-xCl_x film and the reduced hygroscopicity of the PEDOT:PSS film.     

Improved morphology and enhanced stability via solvent engineering for planar heterojunction perovskite solar cells

Solvent engineering technique for planar heterojunction perovskite solar cells is an efficient way to achieve uniformly controlled grain morphology for perovskite films. In this report, diethyl ether solvent engineering technique was used for Methyl ammonium lead triiodide (CH₃NH₃PbI₃) perovskite thin films for planar heterojunction solar cells which exhibited a PCE of 9.20%. Morphological improvements and enhanced grain sizes leads to enhanced absorption of CH₃NH₃PbI₃. Moreover solar cells have showed an excellent environmental stability of more than 100 days. This increase in efficiency is due to improved film morphology of perovskite layer after solvent treatment which has been revealed under UV–Vis spectroscopy, SEM images, X-ray diffraction and impedance spectroscopy.     

High-quality CH3NH3PbI3 thin film fabricated via intramolecular exchange for efficient planar heterojunction perovskite solar cells

The high-quality CH₃NH₃PbI₃ perovskite thin film with excellent coverage and uniformity was prepared using an intramolecular exchange technology via a low-temperature, two-step sequential deposition process. The PbI₂(DMSO) complex was synthesized at room temperature without any additives and was deposited, then the CH₃NH₃I solution was deposited subsequently. The further controllable thermal annealing process resulted in the complete formation of flat and uniform CH₃NH₃PbI₃ thin film with large-size grains and (110) preferred crystallographic orientation. The perovskite solar cells (PSCs) with a very simple inverted planar heterojunction structure of ITO/PEDOT:PSS/CH₃NH₃PbI₃/PCBM/Al and without other buffer layers, e.g., C₆₀, LiF, BCP, etc., were fabricated, resulting in a power conversion efficiency (PCE) as high as 14.26%. The results suggest that the low-temperature, two-step sequential deposition process with intramolecular exchange technology provides a good route to fabricate high-quality perovskite thin film and efficient PSCs, which would match with large-scale, high-output roll-to-roll (R2R) printing/coating techniques.     

Copolymers based on thiazolothiazole-dithienosilole as hole-transporting materials for high efficient perovskite solar cells

The interlayers, including hole transporting layer (HTL) and electron transporting layer (ETL), segregating photoactive layer and the electrodes play an important role in charge extraction and transportation in perovskite solar cells (pero-SCs). Two novel copolymers, PDTSTTz and PDTSTTz-4, for the first time were applied as HTL in the n-i-p type pero-SCs, with the device structure of ITO/compact TiO₂/CH₃NH₃PbI_3-xCl_x/HTL/MoO₃/Ag. The highest occupied molecular orbitals (HOMO) levels of PDTSTTz and PDTSTTz-4 exhibit a suitable band alignment with the valence band edge of the perovskite. Both of them lead to improved device performances compared with reference pero-SCs based on P3HT as HTL. To further balance the charge extraction and the diffusion length of charge carriers, pristine C₆₀ was introduced at the cathode side of the pero-SCs, working together with TiO₂ as ETL. With insertion of both the HTL and ETL, the performance of pero-SCs was greatly enhanced. The optimized devices exhibited impressive PCEs of 14.4% and 15.8% for devices based on PDTSTTz and PDTSTTz-4. The improved performance is attributed to better light harvest ability, decreased interface resistance and faster decay time due to the introduction of the interlayers.     

Synergistic Effect of PbI2 Passivation and Chlorine Inclusion Yielding High Open‐Circuit Voltage Exceeding 1.15 V in Both Mesoscopic and Inverted Planar CH3NH3PbI3(Cl)‐Based Perovskite Solar Cells

Enhancing open‐circuit voltage in CH₃NH₃PbI₃(Cl) perovskite solar cells has become a major challenge for approaching the theoretical limit of the power conversion efficiency. Here, for the first time, it is demonstrated that the synergistic effect of PbI₂ passivation and chlorine incorporation via controlling the molar ratio of PbI₂, PbCl₂ (or MACl), and MAI in the precursor solutions, boosts the open‐circuit voltage of CH₃NH₃PbI₃(Cl) perovskite solar cells over 1.15 V in both mesoscopic and inverted planar perovskite solar cells. Such high open‐circuit voltage can be attributed to the enhanced photoluminescence emission and carrier lifetime associated with the reduced trap densities. The morphology and composition analysis using scanning electron microscopy, X‐ray diffraction measurements, and energy dispersive X‐ray spectroscopy confirm the high quality of the optimized CH₃NH₃PbI₃(Cl) perovskite film. On this basis, record‐high efficiencies of 16.6% for nonmetal‐electrode all‐solution‐processed perovskite solar cells and 18.4% for inverted planar perovskite solar cells are achieved.     

In-situ synthesis of metal nanoparticle-polymer composites and their application as efficient interfacial materials for both polymer and planar heterojunction perovskite solar cells

A new approach for the synthesis of gold nanoparticles (Au NPs) via a simple and fast in-situ generation method using an amine-containing polymer (PN4N) as both stabilizer and reducing agent is reported. The application of the Au NPs-PN4N hybrid material as efficient interfacial layer in different types of solar cells was also explored. The synthesized Au NPs show good uniformity in size and shape and the Au NPs doped PN4N hybrid composites exhibit high stability. Amine-containing polymers are good cathode interfacial materials (CIMs) in polymer solar cells (PSCs) and planar heterojunction perovskite solar cells (PVKSCs). The performance of the PSCs with Au NPs doped PN4N CIMs is largely improved when compares to devices with pristine PN4N CIM due to the enhanced electronic properties of the doped PN4N. Furthermore, by incorporating larger Au NPs into PEDOT:PSS to enhance absorption of the light harvesting layer, power conversion efficiencies (PCEs) of 6.82% and 13.7% are achieved for PSC with PCDTBT/PC₇₁BM as the light harvesting materials and PVKSC with a ∼280 nm-thick CH₃NH₃PbI_3−xCl_x perovskite layer, respectively. These results indicate that Au NPs doped into both PEDOT:PSS and PN4N interlayers exhibited a synergistic effect in performance improvement of PSCs and PVKSCs.     

Efficient planar heterojunction perovskite solar cells fabricated by in-situ thermal-annealing doctor blading in ambient condition

The in-situ thermal-annealing doctor blading was developed to fabricate high-quality perovskite CH₃NH₃PbI₃ thin film and efficient planar heterojunction perovskite solar cells (PHJ-PSCs) in ambient condition with humidity of ∼45%. The morphology of CH₃NH₃PbI₃ thin film fabricated by in-situ thermal-annealing doctor blading varied from random nanowires to oriented domains as increasing the substrate temperature, and the domain size became larger and larger with increasing substrate temperature. The PHJ-PSCs with a structure of ITO/PEDOT:PSS/CH₃NH₃PbI₃/PCBM/Ag was fabricated based on in-situ thermal-annealing doctor-bladed CH₃NH₃PbI₃ thin film in ambient condition, resulting in the power conversion efficiency up to 11.29% without obvious hysteresis under different scanning directions and speeds. The performance is comparable to that of PHJ-PSCs fabricated by spin-coating deposition in glovebox with the same structure. The research results suggested that efficient PHJ-PSCs could be fabricated by large-scale in-situ thermal-annealing doctor blading in ambient condition, which is matchable with large-scale, roll-to-roll process and shows potential application in industrial production.     

Viscosity effect of ionic liquid-assisted controlled growth of CH3NH3PbI3 nanoparticle-based planar perovskite solar cells

A precise control of the morphology and crystallization of perovskite thin-films is well-correlated to higher perovskite solar cells performances. Ionic liquids (ILs) can retard perovskite crystallization to aid the formation of films with uniform morphology to realize highly efficient perovskite solar cells. Herein, we attempt to control the nanostructural growth of CH₃NH₃PbI₃ thin films by adding ILs to the perovskite spin-coating solution and investigate the effect of IL viscosity on the resulting CH₃NH₃PbI₃ nanoparticle (NP) thin films. NPs with desirable morphology were obtained using ILs with a low viscosity that completely dissolved in the CH₃NH₃PbI₃ solution. In particular, the IL tetrabutylammonium chloride yielded NPs with a diameter of 500 nm and controllable morphology, crystallinity, and absorption behavior, which led to improved photovoltaic performance compared with that of solar cells containing NPs produced using other ILs. Our findings revealed a pathway to obtain uniformly distributed CH₃NH₃PbI₃ NP thin films for use in perovskite solar cells. The developed method is well suited for large-scale production of perovskite thin films on flexible substrates.     

Improved performance of CH3NH3PbI3 based photodetector with a MoO3 interface layer

Planar CH₃NH₃PbI₃ perovskite based photodetectors are fabricated by a facile and low-cost one-step method. The devices show broad spectral photoresponse from the ultraviolet to whole visible region and the performance can be significantly improved by the introduction of a bipolar transporting MoO₃ interface layer between CH₃NH₃PbI₃ film and Au electrode. The photocurrent of the device with an optimized MoO₃ layer is about twice that of the reference device without MoO₃ layer, which results in a high ON/OFF current ratio of 5.9 × 10³ at 5 V. Besides, slightly increased photoresponse speed is also found in the optimized device with rise time and decay time of 21.6 and 9.9 ms, respectively. The improvement can be attributed to the improved hole and electron collection efficiency and the quickly filled in or emptied trap states at the CH₃NH₃PbI₃/Au interface due to the introduction of the bipolar transporting MoO₃ layer.     

A low-cost and low-temperature processable zinc oxide-polyethylenimine (ZnO:PEI) nano-composite as cathode buffer layer for organic and perovskite solar cells

Nanocomposite buffer layer based on metal oxide and polymer is merging as a novel buffer layer for organic solar cells, which combines the high charge carrier mobility of metal oxide and good film formation properties of polymer. In this work, a nanocomposite of zinc oxide and a commercialized available polyethylenimine (PEI) was developed and used as the cathode buffer layer (CBL) for the inverted organic solar cells and p-i-n heterojunction perovskite solar cells. The cooperation of PEI in nano ZnO offers a good film forming ability of the composite material, which is an advantage in device fabrication. In addition, power conversion efficiency (PCE) of the ZnO:PEI CBL based device was also improved when compared to that of ZnO-only and PEI-only devices. The highest PCE of P3HT:PC₆₁BM and PTB7-Th:PC₆₁BM devices reached to 3.57% and 8.16%, respectively. More importantly, there is no obvious device performance loss with the increase of the layer thickness of ZnO:PEI CBL to 60 nm in organic solar cells, which is in contrast to the PEI based devices, whose device performance decreases dramatically when the PEI layer thickness is higher than 6 nm. Such a nano composite material is also applicable in inverted heterojunction perovskite solar cells. A PCE of 11.76% was achieved for the perovskite solar cell with a thick ZnO:PEI CBL (150 nm) CBL, which is around 1.71% higher than that of the reference cell without CBL, or with ZnO CBL. In addition, stability of the organic and perovskite solar cells having ZnO:PEI CBL was also found to be improved in comparison with that of PEI based device.     

Efficient lead acetate sourced planar heterojunction perovskite solar cells with enhanced substrate coverage via one-step spin-coating

In planar heterojunction (PHJ) perovskite solar cells (PerSCs) without mesoporous metal oxide skeleton, there is challenge of formation perovskite film with full coverage to the conductive substrate through solution-process the lead halide precursors. Selecting a lead source with more volatile byproducts is an effective approach to obtain much smoother films with smaller and fewer pinholes. Herein, we demonstrate efficient CH₃NH₃PbI₃/PCBM PHJ PerSCs by using lead acetate (Pb(Ac)₂) as lead precursor. The morphology of the perovskite thin films were investigated by scanning electron microscopy (SEM) and atomic force microscopy (AFM), respectively, and the crystalline quality of the perovskite films were investigated by X-ray diffraction (XRD) spectroscopy. Time-resolved photoluminescence (TRPL) was used to investigate the PL lifetime of the perovskite film. The perovskite film derived from Pb(Ac)₂ shows enhanced surface coverage and improved photoluminescence lifetime in comparison with PbI₂ sourced perovskite film. Averaged over 20 individual devices, the power conversion efficiency (PCE) of devices derived from Pb(Ac)₂ reaches 14.81%, much higher than PbI₂ sourced devices by one-step (8.23%) or two-step (10.58%) spin-coating.     

Enhancing the Optoelectronic Performance of Perovskite Solar Cells via a Textured CH3NH3PbI3 Morphology

Perovskite‐based solar cells are generally assembled as planar structures comprising a flat organoammonium metal halide perovskite layer, or mesoscopic structures employing a mesoporous metal‐oxide scaffold into which the perovskite material is infiltrated. To present, little attention has been directed toward the texturing of the perovskite material itself. Herein, a textured CH₃NH₃PbI₃ morphology formed through a thin mesoporous TiO₂ seeding layer and a gas‐assisted crystallization method is reported. The textured morphology comprises a multitiered nanostructure, which allows for significant improvements in the light harvesting and charge extraction performance of the solar cells. Due to these improvements, average short‐circuit current densities for a batch of 28 devices are in excess of 22 mA cm^?2, and the maximum recorded power conversion efficiency is 16.3%. The performance gains concomitant with this textured CH₃NH₃PbI₃ morphology provide further insights into how control of the perovskite microstructure can be used to enhance the cell performance.     

Efficiencies of perovskite hybrid solar cells influenced by film thickness and morphology of CH3NH3PbI3−xClx layer

Perovskite hybrid solar cells (pero-HSCs) have been intensively investigated due to their promising photovoltaic performance. However, the correlations between the efficiencies of pero-HSCs and thin film thicknesses and morphologies of CH₃NH₃PbI_3−xCl_x perovskite layers are rarely addressed. In this study, we report the correlation between the efficiencies of “planar heterojunction” (PHJ) pero-HSCs and the thin film thicknesses and morphologies of solution-processed CH₃NH₃PbI_3−xCl_x perovskite layers. Investigation of absorption spectra, X-ray diffraction patterns, atomic force microscopy and scanning electron microscopy images of CH₃NH₃PbI_3−xCl_x layers indicate that the efficiencies of PHJ pero-HSCs are dependent on the film thickness, as the thickness of CH₃NH₃PbI_3−xCl_x is less than 400 nm; whereas the efficiencies are significantly dependent on the film morphologies of CH₃NH₃PbI_3−xCl_x layers as the thickness is larger than 400 nm. Our studies provide a promising pathway for fabricating high efficiency PHJ pero-HSCs.     

Self-encapsulated semi-transparent perovskite solar cells with water-soaked stability and metal-free electrode

Semi-transparent and self-encapsulated perovskite solar cells could be fabricated by simply laminating the front sub-cell (ITO/poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS)/CH₃NH₃PbI₃) and back sub-cell (FTO/compact-TiO₂/mesoporous-TiO₂/CH₃NH₃PbI₃), without vacuum-evaporating metal electrode. The addition of chlorobenzene (CB) between two perovskite layers accelerated perovskite crystals interfusion and close interfacial contact from two separated sub-cells, which contributed to perovskite film with high crystallinity and light absorption in laminated cells. The self-encapsulated perovskite solar cell (device area of 0.39 cm²) with CB treatment not only showed power conversion efficiency of 6.9%, but also existed excellent stability even if soaking in water for 24 h. This novel approach to fabricate semi-transparent, solution-processible, cost-effective and high-stable perovskite solar cells may provide a reliable royal road for realizing commercial application in exterior building window, with the combination of large-area roll-to-roll printing technique, etc.     

In situ recycle of PbI2 as a step towards sustainable perovskite solar cells

The development of organometal halide perovskite solar cells has grown rapidly and the highest efficiency of the devices has recently surpassed 22%. Because these solar cells contain toxic lead, a sustainable strategy is required to prevent environmental pollution and avoid healthy hazard caused by possible lead outflow. Here, in situ recycling PbI₂ from thermal decomposition CH₃NH₃PbI₃ perovskite films for efficient perovskite solar cells was developed. The thermal behavior of CH₃NH₃PbI₃ perovskite and its individual components were examined by thermogravimetric analysis. By optimizing the process of thermal decomposition CH₃NH₃PbI₃ film, the complete conversion from CH₃NH₃PbI₃ to pure PbI₂ layer with a mesoporous scaffold was achieved. The mesoporous structure readily promotes the conversion efficiency of perovskite and consequently results in high‐performance device. A perovskite crystal growth mechanism on the mesoporous PbI₂ structure was proposed. These results suggest that in situ recycled PbI₂ scaffolds can be a new route in manipulating the morphology of the perovskite active layer, providing new possibilities for high performance. Meanwhile, the risk of lead outflow can be released, and the saving‐energy fabrication of efficient solar cells can be realized.     

Morphological Control for High Performance,Solution‐Processed Planar Heterojunction Perovskite Solar Cells

Organometal trihalide perovskite based solar cells have exhibited the highest efficiencies to‐date when incorporated into mesostructured composites. However, thin solid films of a perovskite absorber should be capable of operating at the highest efficiency in a simple planar heterojunction configuration. Here, it is shown that film morphology is a critical issue in planar heterojunction CH₃NH₃PbI_3‐xCl_x solar cells. The morphology is carefully controlled by varying processing conditions, and it is demonstrated that the highest photocurrents are attainable only with the highest perovskite surface coverages. With optimized solution based film formation, power conversion efficiencies of up to 11.4% are achieved, the first report of efficiencies above 10% in fully thin‐film solution processed perovskite solar cells with no mesoporous layer.     

Blade-Coated Carbon Electrode Perovskite Solar Cells to Exceed 20% Efficiency Through Protective Buffer Layers

Perovskite solar cells with carbon electrode have a commercial impact because of their facile scalability, low-cost, and stability. In these devices, it remains a challenge to design an efficient hole transport layer (HTL) for robust interfacing with perovskite on one side and carbon on another. Herein, an organic/inorganic double planar HTL is constructed based on polythiophene (P3HT) and nickel oxide (NiOx) nanoparticles to address the named challenge. Through adding an alkyl ammonium bromide (CTAB) modified NiOx nanoparticle layer on P3HT, the planar HTL achieves a cascade type-II energy level alignment at the perovskite/HTL interfaces and a preferential ohmic contact at NiOx/carbon electrode, which greatly benefits in charge collection while suppressing charge transfer recombination. Besides, compared with the single P3HT layer, the planar composite enables a robust interfacial contact by protecting perovskite from being corroded by carbon paste during fabrication. As a result, the blade-coated FA_0.6MA_0.4PbI₃ perovskite solar cells (fabricated in ambient air in fume hood) with carbon electrode deliver an efficiency of 20.14%, the highest value for bladed coated carbon and perovskite solar cells, and withstand 275 h maximum power point tracking in air without encapsulation (95% efficiency retained).     

Interface degradation of perovskite solar cells and its modification using an annealing-free TiO2 NPs layer

Interface is one of the most important factors to influence the device stability, which directly determines the commercialization of perovskite solar cells (PSCs). The research disclosed the degradation process and mechanism of planar heterojunction (PHJ) PSCs with a structure of ITO/PEDOT:PSS/CH₃NH₃PbI₃/PCBM/Al using in-situ experiments. The degradation of PHJ-PSCs is mainly attributed to the interface decay of perovskite/cathode. Large amount of bubbles formed quickly at the interface and grew up as PHJ-PSCs exposed to air. The cathode electrode easily peeled off from the devices that led to lose the efficiency completely after only 1 h exposure to air. On the other hand, the degradation driven by intrinsic decomposition of perovskite itself under atmosphere (humidity ∼ 45 RH%) was not obvious and the power conversion efficiency (PCE) could retain almost the same when only the perovskite layer was exposed to air for 200 h. Furthermore, annealing-free TiO₂ nanocrystalline particles (TiO₂ NPs) as an interface modification layer was inserted into PHJ-PSCs and dramatically improved the stability, of which the PCEs retained over 75% of its initial values after exposure to air for 200 h. The results provide important information to understand the degradation of PSCs and the improvement of the stability, which may potentially accelerate the development and commercialization of PSCs.