Feasibility assessment of magnetic resonance-thermometry on pancreas undergoing laser ablation: Sensitivity analysis of three sequences

Laser ablation (LA) is a minimally invasive technique for the treatment of tumors as an alternative to surgical resection. The light absorbed by tissue is converted into heat, and causes irreversible cell damage when temperatures higher than 60 °C are reached. The knowledge in real time of temperature may be particularly beneficial for adjusting laser settings applied during treatment and to be notified in real time about its end-point. As a consequence, several techniques for temperature monitoring within the tissue have been investigated along the last decades. In the field of LA, particularly attractive are non-invasive methods. Among these techniques, thermometry based on the analysis of Magnetic Resonance Imaging (MR-thermometry) has gaining large acceptance in this field. MR-thermometry allows estimating the temperature variation thanks to the thermal dependence of several MRI parameters, among others the most promising are T₁ relaxation time, and proton resonance frequency shift.The aim of this study is to assess the sensitivity of MRI thermometry using three T₁-weighted sequences (i.e., Inversion Recovery Turbo-FLASH, IRTF, Saturation Recovery Turbo-FLASH, SRTF, and FLASH) using an 1.5-T MR scanner on healthy swine pancreases undergoing LA. The reference temperature was measured by MRI-compatible fiber optic sensors (fiber Bragg grating sensors). The sensitivity of the proposed techniques was estimated and compared. The thermal sensitivity of the three sequences was −1.47 ± 0.08 °C⁻¹, −0.95 ± 0.05 °C⁻¹, and −0.56 ± 0.04 °C⁻¹ for IRTF, SRTF and FLASH, respectively. Results show that the proposed technique may be adequate for temperature monitoring during LA.     

Regulation on radial position deviation for vertical AMB systems

As a source of model uncertainty, gyroscopic effect, depending on rotor speed, is studied for the vertical active magnetic bearing (VAMB) systems which are increasingly used in various industries such as clean rooms, compressors and satellites. This research applies H^∞ controller to regulate the rotor position deviations of the VAMB systems in four degrees of freedom. The performance of H^∞ controller is examined by experimental simulations to inspect its closed-loop stiffness, rise time and capability to suppress the high frequency disturbances. Although the H^∞ is inferior to the LQR in position deviation regulation, the required control current in the electromagnetic bearings is much less than that for LQR or PID and the performance robustness is well retained. In order to ensure the stability robustness of H^∞ controller, two approaches, by Kharitonov polynomials and TITO (two inputs & two outputs) Nyquist Stability Criterion, are employed to synthesize the control feedback loop. A test rig is built to further verify the efficacy of the proposed H^∞ controller experimentally. Two Eddy-current types of gap sensors, perpendicular to each other, are included to the realistic rotor-bearing system. A four-pole magnetic bearing is used as the actuator for generation of control force. The commercial I/O module unit with A/D and D/A converters, dSPACE DS1104, is integrated to the VAMB, gap sensors, power amplifiers and signal processing circuits. The H^∞ is designed on the basis of rotor speed 10 K rpm but in fact it is significantly robust with respect to the rotor speed, varying from 6.5 to 13.5 K rpm.     

Gas Oil Piston Prover,primary reference values for Gas-Volume

The paper describes the design, measurement results and uncertainty analyses of the hydraulic driven piston-prover system which has been in operation at VSL since 2008. The 12-meter long, 0.6 m bore piston-prover is used for the realization of Reference Values for Gas-Volume at pressures between 1 and 65 bar(a) at several gases. The principle is based on the displacement of a piston acting as a Gas–Oil separator. The standard has a flow-rate range from 5 to 230 m³/h. The system is designed to calibrate reference meters. The Calibration and Measurement Capability (CMC) of the system is proven to be smaller than 0.1% (k=2). The paper also explains the coherence between the Gas–Oil piston-prover and other traceability generators and ‘flow rate bootstrapper systems’.     

The design of polyaniline based sensor for the qualitative estimation of malonaldehyde

The detection of contaminated food in every stage of processing required new technology for fast identification and isolation of toxicity in food. Since effect of food contaminant are severe to human health, the need of pioneer technologies also increasing over last few decades. In the current study, MDA was prepared by hydrolysis of 1,1,3,3-tetramethoxypropane in HCl media and used in the electrochemical studies. The electrochemical sensor was fabricated with modified glassy carbon electrode with polyaniline. These sensors were used for detection of sodium salt of malonaldehyde and observed that a high sensitivity in the concentration range ∼1 × 10⁻¹ M and 1 × 10⁻² M. Tafel plots show the variation of over potential from − 1.73 V to − 3.74 V up to 10⁻⁵ mol/L indicating the lower limit of detection of the system.     

Triboactive materials for dry reciprocating sliding motion at ultra-high frequency

High-power piezo-electric motors with power densities of 1.4 kW/kg display a potential for substituting hydraulic actuators. For this application, two novel tribometers of the same type have been designed using commercially available components for sliding motion at 40 kHz with amplitudes between 2.5 μm and 5 μm. The tribometers are equipped with means to measure amplitude, frequency, power required to keep the samples in motion and load applied. The effective motion between the two contacting bodies is monitored in each of the tribometers. These data are used to evaluate the coefficient of friction. The wear rate was determined after the tests. The set-ups were tested using well-known 100Cr6H (AISI 52100) samples before investigating novel, non-commercial substrates such as AlFeCrTi-alloys and tungsten carbide-based coatings as well as Magnéli-type coatings (Ti_n?2Cr₂O_2n?1 and Ti_nO_2n?1). This paper presents the principle of the ultra-high frequency tribometers and first tribological quantities of materials and coatings tested up to and above 10¹¹ cycles. Very low wear rates in the range 10^?8 mm³/Nm down to 10^?10 mm³/Nm were determined under dry oscillation in air.     

On-site calibration system for trace humidity sensors

A portable device for calibration of trace humidity sensors and an adopted calibration procedure have been developed. The calibration device is based on humidity generation by permeating water through polymeric membrane tubes. Water vapour transmission rates for various polymers were experimentally determined in order to select the most suitable polymeric material. The developed trace humidity generator consists of a gas-flow polymeric hose immersed in a water reservoir thermostated by a sensor-controlled heater. Mole fractions of water vapour between 1 μmol mol⁻¹ and 350 μmol mol⁻¹ (equivalent to frost-point temperatures from −76 °C to −31 °C) were generated by varying either the operating temperature or gas flow. The operating temperature can be varied from 20 °C to 60 °C and kept stable within 0.1 K. Uncertainty analysis indicated that the trace humidity generator produces gas flows of constant humidity amounts with a relative expanded uncertainty less than 3.4% (k = 2) of the generated value.     

Determination of the thermal conductivity of composted material

The objective of this study was to develop a reliable method for the determination of the thermal conductivity of composted material using the TP08 probe. Study was set out to determine whether the selection of a signal fragment used to establish thermal conductivity (λ), has a significant influence on the results. Also minimum number of measurements was determined for every phase of the composting process. No significant differences were reported between results, but certain changes in the value of λ were noted. In successive stages of the process, thermal conductivity of composted material were: 0.31 ± 0.09, 0.45 ± 0.14, 0.27 ± 0.03 and 0.37 ± 0.17 W m⁻¹ K⁻¹.     

A high frequency digital induction system for condutive flow level measurements

A highly integrated, Field Programmable Gate Array (FPGA) based induction measurement system for conductive flow level measurement is presented. Exploiting under-sampling and digital I/Q demodulation techniques, the system use direct digital sampling and can operate at multiple frequencies (from 100 kHz to over 10 MHz). Details are discussed in both hardware and software aspects. Simulations and experiments at 2.6 MHz and 8.3 MHz are carried out using saline solutions with conductivities of 1.8 S/m and 4.3 S/m to verify the performance of the system. Application of the system for saline level monitoring is implemented and studied, which further proves the applicability of the system in low conductivity object measurements.     

Polymethacrylate optodes: A potential for chemical digital color analysis

The paper describes results of implementing a new kind of optical analytical method, digital color analysis (DCA), in which colorimetric polymethacrylate sensors (optodes) are used. The optodes are made of optically transparent polymethacrylate matrix with physically immobilized analytical reagent which is responsible for the extraction of the analyte into the sensing material and changing its color. The developed optodes can be used in determination of various analytes using both solid-phase spectrophotometer and naked eye. In order to improve accuracy and sensitivity of the naked-eye determination, it is possible to measure visible color changes using digital imaging of the polymethacrylate optode. The digital images then can be represented as basic color (e.g. RGB) data. The DCA determinations of Cu (II), Ag (I) and Co (II) have indicated that the developed optodes are linear in concentration ranges 0.02–0.30; 0.02–0.20 and 0.05–0.25 mg L⁻¹ appropriately with corresponding practical detection limits of 0.01; 0.02 and 0.07 mg L⁻¹.     

AC conduction mechanism and battery discharge characteristics of (PVC/PEO) polyblend films complexed with potassium chloride

New K⁺ ion-conducting polymer blend electrolyte films based on amorphous polymer poly(vinyl chloride) (PVC) and semicrystalline polymer poly(ethylene oxide) (PEO) complexed with KCl salt were prepared using a solution-cast technique. The maximum value of ionic conductivity of a PVC/PEO:KCl (42.5:42.5:15) system is 8.29 × 10⁻⁶ S/cm at 303 K. The absorption edge was found at 4.30 eV for undoped film, while it was observed at 4.03 and 3.93 eV for 10 and 15 wt% KCl doped films, respectively. The direct band gaps for these pure and salt doped PVC/PEO films were found to 4.10, 3.86 and 3.74 eV, respectively, whereas the indirect band gaps were determined as 4.15, 3.72 and 3.64 eV. Transference number values showed that the charge transport in this electrolyte system is predominantly due to ions (t_ion = 0.97). The discharge capacity for PVC/PEO:KCl (42.5:42.5:15) polymer blend electrolyte system is 11 μA/h.     

High immunity wafer-level measurement of MHz current

Wafer-level characterization of functional prototypes of solid state current sensors is usually the first step in the development stage, therefore a dedicated wafer-level measurement systems are required. Especially for MHz characterization, where electromagnetic interference issues became strongly relevant. Thus, for frequencies above 1 MHz, a sophisticated measurement techniques are needed, because parasitic couplings can significantly affect sensor response and other signal processing stages, causing errors or malfunction of the whole system. We propose technique for high immunity MHz current measurement by solid state sensor in wafer-level configuration. The system is especially well-suited for MHz characterization, where electromagnetic interference issues become highly relevant. We showed that balanced transmission provides possibility to reduce interference in the sensor biasing circuit of about 60 dB compared to single-ended method. The effectiveness of the proposed technique was tested in monitoring MHz current in the external line by single magnetoresistive sensors on wafer level.     

Preparation,characterization, electrical conductivity and dielectric studies of Na2SO4 and V2O5 composite solid electrolytes

Composite solid electrolytes (1 − x) Na₂SO₄–(x) V₂O₅ were prepared and characterized by various techniques such as XRD, FT-IR, DTA and SEM. AC impedance spectroscopy revealed that the contribution of grain is strong enough over the grain boundary. Arrhenius plot of the Na₂SO₄ shows a sharp increase in conductivity at 523 K due to the structural phase transition (phase V → I). Composites show the enhanced ionic conductivity than the pristine Na₂SO₄ over the entire temperature range. The maximum conductivity σ = 0.003 S cm⁻¹ at 773 K with the lowest activation energy of 0.28 eV was observed for the x = 0.4 sample. The enhanced value of dielectric constant and dielectric loss in the case of composites was obtained because of increase of conductivity, resulted from the increase of space charge polarization and charge motion.     

Analysis of tunnel displacement accuracy with total station

The remote distance measurement (RDM) method requires only common total stations and not special post-processing software. Moreover, this method is easy to operate and highly accurate results can be obtained. Therefore, RDM is used in the displacement monitoring of tunnel engineering. This study presents the calculation formulas for the crown settlement and wall convergence of tunnel as measured by RDM with total station. The mean error formulas are derived based on error propagation laws. When tunnel displacements measured by using total station with the m_s not more than 2 mm + 2D ppm (D is the measurement distance) and m_α not more than 1″, the horizontal distance between the rear viewpoint and the monitoring section is in the range of 50–150 m, the horizontal distance between the total station and the monitoring section ranges from 40 m to 60 m, and the total station is near the tunnel centerline, the measurement accuracy can reach 1 mm.     

Design and characterization of a real-time,wearable, endosomatic electrodermal system

This paper presents the design and characterization of a compact wearable system for long-term assessment of skin potential response, with the aim of monitoring mental stress in a variety of applications. Literature reports that the expected skin potential has peak-to-peak amplitudes of few millivolts in the frequency band [0.1, 10] Hz. The designed system is characterized by a slightly wider bandwidth of [0.08, 40] Hz, and it is based on a 12-bit ADC working with a sampling rate of 200 Sa/s, which can be increased up to 3.5 kSa/s. Data can be continuously acquired for up to 40 h with a battery of 3.7 V/1800 mAh. A Graphical User Interface was also developed for the host computer in .NET framework. The system, to our knowledge the first example of wearable endosomatic electrodermal activity sensor, joins to several skin conductance wearable measuring systems recently proposed in literature, and opens up opportunities for future comparisons of endosomatic and exosomatic responses in real life.The device is thoroughly characterized in accordance with the state-of-the-art of the metrological research in the field.     

1-N-alkyl -3-methylimidazolium ionic liquids as neat lubricants and lubricant additives in steel–aluminium contacts

The influence of the alkyl chain length and of the anion on the lubricating ability has been studied for the room-temperature ionic liquids (IL) 1-n-alkyl-3-methylimidazolium X⁻ [X = PF₆; n = 6 (L-P106). X = BF₄; n = 2 (L102), 6 (L106), 8 (L108). X = CF₃SO₃; n = 2 (L-T102). X = (4-CH3C6H4SO3); n = 2 (L-To102)]. Neat IL have been used for AISI 52100 steel-ASTM 2011 aluminium contacts in pin-on-disk tests under variable sliding speed. While all IL give initial friction values lower than 0.15, real-time sharp friction increments related to tribochemical processes have been observed for L102 and L-P106, at room-temperature and at 100 °C. Electronic microscopy (SEM), energy dispersive (EDS) and X-ray photoelectron (XPS) spectroscopies show that wear scar surfaces are oxidized to Al₂O₃ and wear debris contain aluminium and iron (for L102) fluorides. For L-P106, the steel surface is covered with a P-containing tribolayer. A change of anion (L-T102; L-To102) reduces friction and wear, but the lowest values are obtained by increasing the alkyl chain length (L106; L108). When the more reactive L102 and L-P106 are used as 1 wt.% base oil additives at 25 °C, tribocorrosion processes are not observed and a friction reduction (69–75% for 1 wt.% L102) and a change from severe (10⁻³ mm³ m⁻¹) to mild wear (10⁻⁴ to 10⁻⁶ mm³ m⁻¹) is obtained with respect to the neat IL. 1 wt.% IL additives also show good lubricating performance at 100 °C.     

Identification and characterisation of steel corrosion using passive high frequency RFID sensors

High frequency RFID sensors are attractive in diverse applications where sensor performance is required at a low cost and dimension restriction. An approach adapting commercial passive 13.56 MHz RFID tags has been developed for sensing corrosion stage. This investigation includes balance of sensing and positioning of RFID sensors for corrosion detection by analysing real and imaginary parts of the complex impedance. With passive HF RFID sensors, real part and imaginary part of complex impedance have been extracted from the reader coil with VNA (vector network analyser) and delivering a unique capability for corrosion sensing with different atmospheric exposure time steel samples (1 month, 6 months, 10 months and 12 months). With different positioning (5–25 mm), features extraction based on the complex impedance with PCA (principal component analysis) has been designed for position-independent corrosion evaluation.     

An improved portable biosensing system based on enzymatic chemiluminescence and magnetic immunoassay for biological compound detection

In this paper, an improved portable biosensing system has been developed for biological compounds detection. The device is based on enzymatic chemiluminescence and magnetic immunoassay with a miniaturized flow injection module. The immunoassay procedure involved a sandwich format, in which the antigen in the sample was first captured by the immobilized primary antibody on the surface of the magnetic beads, and then recognized by the second antibody labeled with enzyme. 3-(2′-spiroadamantyl)-4-methoxy- 4-(3″-phosphoryloxy)-phenyl-1,2-dioxetane (AMPPD) as the substrate amplified the enzymatic signal for the biological compound measurement. The portable biosensing system was characterized in a series of experiments with cardiac troponin I (cTnI), a golden standard protein marker for diagnosis of myocardial infarction, as a biological substance measurement model. It provided a linear response range of cTnI from 0.1 to 50 ng mL⁻¹ (R = 0.99). The coefficient of variation was 6.7% in the repeatability test (n = 6). The novel system has great potential applications in the rural and community hospitals and can be easily extended to a variety of protein compounds analysis.     

Potential step study of electrooxidation of methanol in 1-butyl-3-methylimidazolium tetrafluoroborate

A potential step method was used to characterize the electrooxidation of methanol on a chemically modified electrode in an ionic liquid solvent. Two major findings were reported from this study. Firstly, the oxidation was dominant 2.2 s after the potential step. Before that, the double layer charging and adsorption were dominant. Therefore, there should be a waiting time of a few seconds if a methanol sensor is developed with a potential step method. Secondly, the oxidation of methanol on the electrode was diffusion controlled. The concentration of methanol affected the diffusion. The diffusion constant D₀ was 8.37 × 10⁻¹⁷ m²/s when the concentration was lower than 0.5 M and was 2.66 × 10⁻¹³ m²/s when the concentration was higher than 1.0 M. This suggests that the methanol concentration should be kept higher than a threshold in an ionic liquid based fuel cell.     

Multi-range sensors for the measurement of liquid film thickness distributions based on electrical conductance

The paper presents an approach toward an enhancement of the measuring range of high-speed sensors for the measurement of liquid film thickness distributions based on electrical conductance. This type of sensors consists of electrodes mounted flush to the wall. The sampling of the current generated between a pair of neighboring electrode is used as a measure of the film thickness. Such sensors have a limited measuring range, which is proportional to the lateral distance between the electrodes. The range is therefore coupled to the spatial resolution. The proposed new design allows an extension of the film thickness range by combining electrode matrices of different resolution in one and the same sensor. In this way, a high spatial resolution is reached with a small thickness range, whereas a film thickness that exceeds the range of the high resolution measurement can still be acquired even though on the costs of a lower spatial resolution. A simultaneous signal acquisition with a sampling frequency of 3.2 kHz combines three measuring ranges for the characterization of a two-dimensional film thickness distribution: (1) thickness range 0–600 µm, lateral resolution 2×2 mm², (2) thickness range 400–1300 µm, lateral resolution 4×4 mm², and (3) thickness range 1000–3500 µm, lateral resolution 12×12 mm². The functionality of this concept sensor is demonstrated by tests in a horizontal wavy stratified air–water flow at ambient conditions. Using flexible printed circuit board technology to manufacture the sensor makes it possible to place the sensor at the inner surface of a circular pipe.     

On the film thickness dependence of shear strengths in sliding,boundary-layer friction

The density functional theory calculated pressure-dependent shear strength S of a four-layer slab of KCl on a Fe(1 0 0) substrate is compared to previous calculations for a bilayer slab to gauge the effect of film thickness on the shear properties of the film. It is found that the shear strength varies with pressure as S = S₀ + αP, where P is the contact pressure. The resulting calculated values for the four-layer slab are S₀〈1 0〉 = 62 ± 15 and S₀〈1 1〉 = 65 ± 11 MPa while α〈1 0〉 and α〈1 1〉 are 0.06 ± 0.01. The values are very close to those calculated for the bilayer slab of S₀〈1 0〉 = 64 ± 9 and S₀〈1 1〉 =69 ± 8 MPa and α〈1 0〉 and α〈1 1〉 of 0.05 ± 0.01, and in reasonable agreement with the experiment values. These results suggest that the thickness of the film does not have a profound effect on the shear properties.