A green polymer self‐etching strategy for fabricating superhydrophobic surfaces exhibiting low and high adhesion is proposed by using hot‐pressing and exfoliation on a pair of low density polyethylene (LDPE) films. It is demonstrated that the hot‐pressing temperature has significant influence on the surface morphology of LDPE. Effective hot‐pressing temperature for low‐adhesive superhydrophobicity ranges from 109 to 161 °C. Bird's‐nest like micro‐/nanostructures are observed in the unzipped LDPE surfaces compressed at 109 °C, which shows excellent water repellency. LDPE surface compressed at 108 °C demonstrates superhydrophobicity with high adhesion, i.e., a water droplet cannot roll off even when the surface is turned upside down. Furthermore, superhydrophobic vessels are processed and applied to transport water and microdroplets of water losslessly.
Mechanically robust and self‐healing rubbers are highly desired to satisfy the increasing demand of high‐performance smart tires and related materials. Herein, a self‐healing rubber nanocomposite with enhanced mechanical and self‐healing performance based on Diels–Alder chemistry has been investigated. The furfuryl grafted styrene‐butadiene rubber and furfuryl terminated MWCNT (MWCNT‐FA) are reacted with bifunctional maleimide to form a covalently bonded and reversibly cross‐linked rubber composite. Obvious reinforcing effect is obtained at high cross‐linking density. Over 200–300% increase in the Young's modulus and toughness can be achieved in the rubber nanocomposites with 5 wt% MWCNT‐FA. Meanwhile, the healing efficiency increased with MWCNT‐FA content. MWCNT‐FA plays dual roles of effective reinforcer and a kind of healant.
We herein report on an iontronic device to drive and control Aβ1‐40 and Aβ1‐42 fibril formation. This system allows kinetic control of Aβ aggregation by regulation of H+ flows. The formed aggregates show both nanometer‐sized fibril structure and microscopic growth, thus mimicking senile plaques, at the H+‐outlet. Mechanistically we observed initial accumulation of Aβ1‐40 likely driven by electrophoretic migration which preceded nucleation of amyloid structures in the accumulated peptide cluster.
Three different dopants are used to fabricate electrospun dopants/polystyrene (dopants/PS) composite fibers from PS solution and PS sol. The relative humidity and the influence of the dopants on the morphologies, diameter, porous structures, and dopant distribution of electrospun PS fibers are investigated. Compared to those obtained from PS solution, electrospun dopants/PS composite fibers from PS sol with hollow‐porous and multichannel hollow‐porous structures present significant advantages due to the multi‐stage degree of interfacial structure and diversity of the internal environment. In comparison to coaxial electrospun PS fibers, the electrospun dopants/PS composite fibers from PS sol obtained in one step have an improved yield and a simplified technological process simultaneously, leading to significant competitiveness in fields such as catalysis, fluidics gas storage, and sensing.
Colloidal assemblies of inorganic nanoparticles dispersed in liquid media hold particular promise for the creation of a unique class of functional materials with innovative applications. In the present report, “compound‐eye”‐like core–shell and Janus‐type silica and amino‐terminated 1,2‐polybutadiene (PB‐NH2) and polystyrene (PS) composite microspheres are successfully prepared by simply mixing an aqueous dispersion of silica particles into a tetrahydrofran (THF) solution of PB‐NH2, and PB‐NH2 and PS blends, followed by evaporation of the THF. This co‐precipitation process provides a new approach for producing organic–inorganic composite particles without the need for surface modification of the inorganic nanoparticles.
Ferroelectric polymer nanowires grown using a template‐wetting method are shown to achieve an orientated “self‐poled” structure resulting from the confined growth process. Self‐poling is highly desirable as it negates the need for high electric fields, mechanical stretching, and/or high temperatures typically associated with poling treatments in ferroelectric polymers, as required for piezoelectric and/or pyroelectric applications. Here, differential scanning calorimetry, infrared spectroscopy, and dielectric permittivity measurements have been presented on as‐fabricated template‐grown polyvinylidene fluoride‐trifluoroethylene nanowires, and quantitatively compared with spin‐cast films of the same composition that have been electrically poled, both before and after subsequent depoling temperature treatment. The measurements reveal remarkably similar trends between the physical properties of the as‐grown nanowires and the electrically poled film samples, providing insight into the material structure of the “self‐poled” nanowires. In addition, piezoresponse force microscopy data are presented that allow for unambiguous identification of self‐poling in ferroelectric polymer nanostructures. Our results indicate the suitability of the template‐wetting approach in fabricating nanowires that can be used directly for piezoelectric/pyroelectric applications, without the need for post‐deposition poling/processing.
Microcapsules containing an ionic liquid (IL) are potential candidate materials for preparing in situ self‐lubricating composites with excellent tribological properties. 1‐ethyl‐3‐methylimidazolium bis[(trifluoromethyl) sulfonyl]imide ([EMIm]NTf2) IL encapsulated polysulphone microcapsules are synthesized. The mean diameter and wall thickness are about 128 μm and 10 μm, respectively. Microcapsules have excellent thermal stability, with a thermal degradation onset temperature of 440 °C compared to traditional lubricants‐loaded microcapsules. In situ self‐lubricating composites are prepared by incorporating the IL‐encapsulated microcapsules into epoxy matrix. When the concentration of the IL microcapsules is 20 wt%, the frictional coefficient and specific wear rate of composites are reduced by 66.7% and 64.9% under low sliding velocity and middling applied load conditions, respectively, as compared to the neat epoxy. The tribological behavior of the self‐lubricating composites is further assessed in different applied load and sliding velocity conditions. The in situ self‐lubricating mechanism of composites is proposed.
Preparation of novel nanocomposite hydrogels opens up new avenues to next generation of biocompatible materials to be used in bioengineering and drug delivery. Toward this goal, chitosan nanocomposite hydrogels using click chemistry inspired cross‐linking are prepared. To enable this, Diels–Alder reaction of furan‐containing chitosan and maleimide‐coated gold nanoparticles is employed. The viscoelastic properties of the obtained nanocomposites as well as the effect of the nanoparticles as cross‐linkers are studied, indicating that they play significant role in hydrogel formation and stability. Nanoparticle‐enriched hydrogels are also found to demonstrate pH‐sensitivity therefore showing their potential for future biosensing applications.
Pollution control has become increasingly important in recent years. Heavy metal ions, proteins, and dyes are frequently found in wastewater because of their extensive industrial applications. In this study, pH, temperature, and magnetic triple‐responsive poly(N‐isopropylacrylamide‐co‐methacrylic acid) porous microspheres doped with magnetite nanoparticles as a new type of smart adsorbents are used to remove the aforementioned pollutants. The pH‐ and temperature‐responsiveness of these microspheres realizes tunable adsorption toward Cu(II). Simultaneously, the microspheres exhibit good adsorption capability to lysozyme and basic fuchsine. Microsphere‐adsorbing pollutants are easlily separated from wastewater by applying an external magnetic field to reuse the microspheres.
The introduction of nanodiamond particles (NDs) in silane‐crosslinked polyethylene is found to lead to a notable and systematic deformation of the polymer unit cell. X‐ray diffraction evidence of the existence of a modified crystalline structure in the bulk of the polymer due to the presence of NDs is reported here for the first time. The covalent bonding between NDs and the surrounding macromolecular chains may support that the excessive local stress field ultimately distorts the polymer conformation, yielding a new distorted but still crystalline interface. Supporting data from solid‐state NMR experiments confirm the existence of a modified crystalline interface of about 1–2 nm in all the nanocomposite materials.
Hydrophobic and super‐hydrophobic materials have many important applications, but most of the artificially hydrophobic and super‐hydrophobic surfaces suffer from poor durability. Herein, a facile method is reported to fabricate robust hydrophobic and super‐hydrophobic polymer films through backfilling the silica colloidal crystal templates with the mixture of fluoropolymer, thermoset hydroxyl acrylate resins, and curing agent. After removal of the template, 3D ordered porous structures are obtained. The obtained polymer films have not only excellent hydrophobic or super‐hydrophobic properties but also good stability against temperatures, acids, and alkalis. Dual ordered porous structure can obviously enhance the hydrophobicity of polymer films compared to unitary one.
Acrylonitrile–butadiene–styrene (ABS) is a polymer composing of acrylonitrile, butadiene, and styrene. It has been widely used in industry because of its good mechanical and physical properties. The fabrication of ABS fibers, however, has been rarely studied. Here the fabrication of ABS fibers has been reported by an electrospinning technique, in which the sizes and morphologies of the fibers can be controlled by adjusting the electrospinning conditions. The morphologies of the ABS fibers can also be transformed by annealing the fibers on poly (methyl methacrylate) (PMMA) films. After annealing, the ABS fibers gradually transform to ABS particles embedded in the PMMA films by a mechanism similar to the Rayleigh‐instability‐type transformation. To extend the applications of the electrospun ABS fibers, electroless deposition of copper is also conducted, resulting in copper‐coated ABS fibers.
A new facile approach for the fabrication of polymer‐Ag honeycomb film is reported. A polymer‐Ag+ honeycomb thin film is obtained by casting a CHCl3 solution of a functional graft copolymer on aqueous silver nitrate solution, leading to metal complexation induced phase separation at the air/water interface. The film is reduced by UV irradiation to give a polymer‐Ag honeycomb film with regular morphology. Pyrolysis of the film gives a translucent Ag honeycomb film.
A polydimethylsiloxane (PDMS)‐based fluidic device with two flow channels is fabricated by using a rapid prototyping method. The PDMS‐based fluidic device is used to produce water‐in‐oil emulsion (W/O) droplets due to its intrinsic hydrophobicity. To produce uniform oil‐in‐water (O/W) emulsion droplets, the inner channel of the PDMS fluidic device is coated with polydopamine (PDA) by flowing a dopamine precursor in the water channel of the fluidic device. The PDA coating is confirmed by an increase in morphological roughness and nitrogen content. In addition, the contact angle of the PDMS surface decreases from 95° to 30° during PDA coating, suggesting that the inner surface of the fluidic device is hydrophilic. Uniform W/O and O/W emulsion droplets are produced by the pristine PDMS and PDA‐coated PDMS fluidic devices, respectively.
A self‐cleaning membrane that periodically rids itself of attached cells to maintain glucose diffusion could extend the lifetime of implanted glucose biosensors. Herein, we evaluate the functionality of thermoresponsive double network (DN) hydrogel membranes based on poly(N‐isopropylacrylamide) (PNIPAAm) and an electrostatic co‐monomer, 2‐acrylamido‐2‐methylpropane sulfonic acid (AMPS). DN hydrogels are comprised of a tightly crosslinked, ionized first network [P(NIPAAm‐co‐AMPS)] containing variable levels of AMPS (100:0–25:75 wt% ratio of NIPAAm:AMPS) and a loosely crosslinked, interpenetrating second network [PNIPAAm]. To meet the specific requirements of a subcutaneously implanted glucose biosensor, the volume phase transition temperature is tuned and essential properties, such as glucose diffusion kinetics, thermosensitivity, and cytocompatibility are evaluated. In addition, the self‐cleaning functionality is demonstrated through thermally driven cell detachment from the membranes in vitro.
Segmental polyurethanes (PU) with hydrophilic segments form colloidal dispersions which are ultimately arrested into gel‐like structure in aqueous continuous phase owing to the differential interactions between polymer and solvent. These structural states of amphiphilic PUs evolve hierarchically, but the structure‐function correlation between PU colloidal dispersion and gels is not clear. Here, this correlation is defined from the mechanomorphology of hydrophilic polyethylene glycol based PU which forms dispersions and finally transforms into gel‐structure. Morphological and rheological analyses show that PU with comparable hydrophilic and hydrophobic content forms attractive colloids with self‐similar fractal microstructures whereas PU with increased hydrophilic character forms space‐filling colloids without any defined organization. Furthermore, colloidal dispersions are densified under shear or gravity to form gel where gel mechanics is defined by colloidal particle organization and the morphology is dependent on gelation mode. This stepwise organization of PU colloidal particles into microgel can independently control microgel mechanics and morphology.
One major challenge of biomaterial engineering is to mimic the mechanical properties of anisotropic, multifunctional natural soft tissues. Existing solutions toward controlled anisotropy include the use of oriented reinforcing fillers, with complicated interface issues, or UV‐curing processing through patterned masks, that makes use of harmful photosensitive molecules. Here, a versatile process to manufacture biocompatible silicone elastomer membranes by light degradation of the platinum catalyst prior to thermal cross‐linking is presented. The spatial control of network density is demonstrated by experimental and theoretical characterizations of the mechanical responses of patterned cross‐linked membranes, with a view to mimic advanced implantable materials.
In the present study, the covalent bonding of electroconductive cross‐linked hydrogel networks with both electro‐properties and hydrogel characteristics to titanium surfaces via a UV‐initiated radical thiol‐ene click reaction is investigated. The electroconductive hydrogel layers are formed by the electropolymerization of pyrrole within the titanium implant‐supported gelatin methacrylate hydrogel. Characterization of the surface morphology of the layers reveals a unique rough macroporous structure. The hydrogel coating layer on the titanium surfaces possesses the desired characteristics of high electrochemical activity and high mechanical stability due to the effects of the chemical functionalization. Bone mesenchymal stem cells cultured on the hydrogel substrates exhibit high cell viability. This study is the first to demonstrate the potential of an electroconductive hydrogel as a surface coating on titanium implants for cell growth and provides a foundation for the development of new implantable bioelectronic devices.
Porous polymer materials prepared from biodegradable polymers have received considerable attention due to their potential as cell culture scaffolds for tissue engineering. Porous materials are generally sterilized by autoclaving prior to use as cell culture scaffolds to avoid unexpected biological infection. However, the melting point of biodegradable polymers is typically lower than the temperature used in autoclave sterilization. Here, the preparation of honeycomb films comprising a poly(L‐lactic acid) (PLLA) and poly(D‐lactic acid) (PDLA) stereo complex is described and their thermal stabilities are evaluated. The hierarchic photochemical patterning of PLLA/PDLA stereo complex honeycomb‐patterned films by UV‐O3 treatment is also demonstrated.
Light triggered soft actuator in aqueous media has applications in operating underwater objects, creating liquid flow, and adjusting reaction velocity, etc. Here, composites prepared from commercial materials, poly[ethylene‐ran‐(vinyl acetate)] (EVA) and aniline black (AB), are reported as one cost efficient material for preparing such actuator, where EVA and AB work respectively as shape‐memory polymer matrix and near‐infrared light triggered photothermal filler. Upon irradiation, the temperature of the composites increases greatly with light power density and AB content. Light‐induced shape‐memory effect (SME) with recovery ratio >98%, temperature‐memory effect (TME), and reversible bidirectional shape‐memory effect (rbSME) of the prepared composites in air are realized. Higher light power density is required to trigger the shape recovery in aqueous media, while good SME, TME, and rbSME are also achieved. Releasing device and gripper are used to indicate the feasibility of the composites as light triggered soft underwater actuators.
下载免费PDF全文