Mechanically robust and self‐healing rubbers are highly desired to satisfy the increasing demand of high‐performance smart tires and related materials. Herein, a self‐healing rubber nanocomposite with enhanced mechanical and self‐healing performance based on Diels–Alder chemistry has been investigated. The furfuryl grafted styrene‐butadiene rubber and furfuryl terminated MWCNT (MWCNT‐FA) are reacted with bifunctional maleimide to form a covalently bonded and reversibly cross‐linked rubber composite. Obvious reinforcing effect is obtained at high cross‐linking density. Over 200–300% increase in the Young's modulus and toughness can be achieved in the rubber nanocomposites with 5 wt% MWCNT‐FA. Meanwhile, the healing efficiency increased with MWCNT‐FA content. MWCNT‐FA plays dual roles of effective reinforcer and a kind of healant.
A conjugated polymer, poly(9,9‐bis(6‐bromohexyl)‐9H‐fluorene‐alt‐1,4‐phenylene), is synthesized, converted to nanoparticles via a nanoprecipitation process, and utilized to fabricate thin films including conjugated polymer nanoparticles. The nanoparticles with surface bromides can be conjugated with an amine‐functionalized dendrimer via a nucleophilic coupling reaction. Thus, when microliter solutions of the particulates are dragged at a constant velocity on substrates alternately in a layer‐by‐layer manner, thin films composed of the nanoparticles and dendrimers can be successfully built up on the substrates. Our results suggest a methodology to control the deposition of thin films bearing conjugated polymer nanoparticles while minimizing processing time and decreasing material consumption.
The effects of ethylene oxide (EO), vaporized hydrogen peroxide (VHP), gamma (γ) radiation, and electron‐beam (E‐beam) on the physiochemical and morphological properties of medical device polymers are investigated. Polymers with ether, carbonate, carboxylic acid, amide and ester functionalities are selected from a family of poly(ethylene glycol) (PEG) containing tyrosine‐derived polycarbonates (TyrPCs) to include slow, medium, fast, and ultra‐fast degrading polymers. Poly(lactic acid) (PLA) is used for comparison. Molecular weight (Mw) of all tested polymers decreases upon gamma and E‐beam, and this effect becomes more pronounced at higher PEG content. Gamma sterilization increases the glass transition temperature of polymers with high PEG content. EO esterifies the carboxylic acid groups in desaminotyrosol‐tyrosine (DT) and causes significant degradation. VHP causes hydroxylation of the phenyl ring, and hydrolytic degradation. This study signifies the importance of the chemical composition when selecting a sterilization method, and provides suggested conditions for each of the sterilization methods.
This study describes novel and simple conditions for the fabrication of collagen microfibers with specific physical and mechanical properties, which can then be potentially applied as cell‐based matrices. The microfibers are fabricated from collagen hydrogels, using various concentrations of ethanol, in ethanol–water solvents. At higher ethanol concentration, fibers exhibited increased uniformity of surface morphology, decreased diameter, and increased tensile strength. The morphology of cells on microfibers varies due to the surface morphology of microfibers but the microfibers fabricated under all conditions investigated show similar number of attached cells on the surface of fibers, and cells sustain their viability for 90 h.
Dopamine is a molecule that facilitates biomineralization, and it is used to prepare electropolymerization‐induced polydopamine (PDA). For the first time, dopamine is used for template‐free electrochemical polymerization to form biocompatible polypyrrole (PPy) nanofiber coatings on bone implants. Dopamine monomers are electropolymerized to PDA chains affixed to biomedical titanium after the nanomicelles are tuned to self‐assemble by triggering the potential, resulting in nanofiber formation. Dopamine serves as a dopant to induce the formation of conductive PPy nanofibers and as a promoter to accelerate biomineralization, cell proliferation, and adhesion.
Segmental polyurethanes (PU) with hydrophilic segments form colloidal dispersions which are ultimately arrested into gel‐like structure in aqueous continuous phase owing to the differential interactions between polymer and solvent. These structural states of amphiphilic PUs evolve hierarchically, but the structure‐function correlation between PU colloidal dispersion and gels is not clear. Here, this correlation is defined from the mechanomorphology of hydrophilic polyethylene glycol based PU which forms dispersions and finally transforms into gel‐structure. Morphological and rheological analyses show that PU with comparable hydrophilic and hydrophobic content forms attractive colloids with self‐similar fractal microstructures whereas PU with increased hydrophilic character forms space‐filling colloids without any defined organization. Furthermore, colloidal dispersions are densified under shear or gravity to form gel where gel mechanics is defined by colloidal particle organization and the morphology is dependent on gelation mode. This stepwise organization of PU colloidal particles into microgel can independently control microgel mechanics and morphology.
Four bromine‐containing methacrylates 1 – 4 are synthesized from pentaerythritol tribromide and 2,2,2‐tribromoethanol and are characterized by 1H and 13C NMR spectroscopy. Their free radical polymerization is performed in dimethylformamide (DMF), using 2,2′‐azobis(2‐methylpropionitrile) as initiator. The photopolymerization behavior of monomers 1–4 is investigated using a differential scanning calorimeter. Homopolymerizations and copolymerizations with 2‐hydroxyethyl methacrylate are carried out. Both the presence of a carbamate group and of bromine atoms result in an increase of the polymerization rate. Dental resins are prepared by replacing a certain amount of 2‐(4‐cumyl‐phenoxy)ethyl methacrylate by monomers 3 and 4 in a model formulation. The incorporation of these methacrylates leads to a significant increase of the radiopacity. Resins based on monomer 4 exhibit improved mechanical properties.
Superabsorbent hydrogel nanocomposites (SHN) with semi‐interpenetrating polymer network (semi‐IPN) are synthesized by the polymerization of acrylamide monomer in a polyethylene glycol aqueous solution in the presence of the octadecylamine (ODA)‐modified graphene oxide (GO‐ODA) nanosheets. The hydrogel composites are characterized by Fourier transform infrared spectroscopy, thermal gravity analysis, and scanning electron microscopy. The water absorbency of the resulting SHN in distilled water and saline solutions are measured. The results show that doping GO‐ODA nanosheets into hydrogel semi‐IPN would enhance both their salt resistance and water retention. Using a simple freezing‐dry method, porous SHN with macroscopically interconnected pores is prepared, which exhibits excellent separation ability for removal of trace water from oils. Based on their better water absorbency, salt resistance, and excellent oil/water separation ability, the resulting SHN has great potentials in a wide range of applications, for example, oil dehydration, absorption, and separation.
Nanofiber‐based hydrocolloid scaffold is prepared by colloid electrospinning of thermoplastic polyurethane (TPU)/sodium carboxymethyl cellulose (S.CMC) in tetrahydrofuran (THF)/dimethylformamide (DMF). The most suitable process of electrospinning for successful formation of fibers is investigated by controlling the concentration of polymeric solution and co‐solvent ratio. In order to accomplish high wettability, the amount of colloid (S.CMC) and the co‐solvent ratio (THF/DMF), which affects the morphology of fibers, are adjusted. Finally, the open wound healing effect is confirmed using nanofiber‐hydrocolloid from in vivo animal studies. A detailed study of the wound healing process is also demonstrated for the first time.
Using synchrotron‐radiation X‐rays for nanoscale computed tomography (X‐ray nano‐CT), the structure and corresponding reinforcement effects of carbon black (CB) filler at various amounts in natural rubber (NR) are studied during cyclic loading. All structural parameters of the CB filler, which are extracted from X‐ray images—such as the destruction and reconstruction ratios of the aggregates and the network connectivity, show a transition point with the CB content at around 30 phr (phr = parts by weight per hundred parts of rubber). When the CB content is above the transition point, the effective volume fraction exceeds the percolation threshold, and a stress‐bearing filler network can form; this network can effectively transmit the external stress to the entire sample and abruptly enhance the reinforcement factor. Below the percolation threshold, the CB filler is mainly disconnected aggregates, where its reinforcement of the rubber matrix can be mainly described by the volume‐filling effect. Using the dynamic cluster–cluster aggregation (CCA) model, calculations of the mechanical properties related to the CB content suggest that the network structure plays a major role in the reinforcement of the NR.
The flame retardancy and mechanical properties of polyamide‐6 (PA6)/aluminum diethylphosphinate (AlPi) composite are greatly improved by the addition of novelly synthesized phosphorus flame retardant‐based diepoxide (DEP) during extrusion. The PA6/AlPi/DEP composite passes V‐0 rating of UL94 test with limiting oxygen index (LOI) of 32.6% at 13 wt% AlPi and 1 wt% DEP, as revealed by the results of flammability. The synergistic flame retardation mechanism offered by the two additives (AlPi and DEP) is studied in terms of in‐depth characterization of the charred residue and evolved gas. The deteriorated mechanical strength of PA6 due to existence of AlPi is compensated by the simultaneous chain extension effect of DEP. Accordingly, the flexural and impact strengths of PA6/AlPi/DEP composite are even superior to those of neat PA6.
A green polymer self‐etching strategy for fabricating superhydrophobic surfaces exhibiting low and high adhesion is proposed by using hot‐pressing and exfoliation on a pair of low density polyethylene (LDPE) films. It is demonstrated that the hot‐pressing temperature has significant influence on the surface morphology of LDPE. Effective hot‐pressing temperature for low‐adhesive superhydrophobicity ranges from 109 to 161 °C. Bird's‐nest like micro‐/nanostructures are observed in the unzipped LDPE surfaces compressed at 109 °C, which shows excellent water repellency. LDPE surface compressed at 108 °C demonstrates superhydrophobicity with high adhesion, i.e., a water droplet cannot roll off even when the surface is turned upside down. Furthermore, superhydrophobic vessels are processed and applied to transport water and microdroplets of water losslessly.
The present work focuses on the influence of nucleation processes on the crystallization of bio‐based poly(ethylene 2,5‐furandicarboxylate) (PEF). Nuclei formation has been studied by means of fast scanning calorimetry (FSC) both when cooling from the melt (nonisothermal conditions) and when annealing at either low‐ or high‐temperatures (isothermal conditions). FSC results show that nucleation on cooling can be prevented by using fast rates allowing to keep the polymer in its amorphous state; whereas cooling at moderate rates results in sample nucleation with a subsequent increase of the crystallization rate. Isothermal pretreatment just above the PEF glass transition temperature (Tg) results in nuclei formation whose rate decreases when the nucleation temperature approaches PEF Tg. On the other hand, annealing below the PEF melting point allows determination of the sample self‐nucleation behavior which occurs in a very narrow temperature range, i.e., between 195 and 198 °C.
Porous polymer materials prepared from biodegradable polymers have received considerable attention due to their potential as cell culture scaffolds for tissue engineering. Porous materials are generally sterilized by autoclaving prior to use as cell culture scaffolds to avoid unexpected biological infection. However, the melting point of biodegradable polymers is typically lower than the temperature used in autoclave sterilization. Here, the preparation of honeycomb films comprising a poly(L‐lactic acid) (PLLA) and poly(D‐lactic acid) (PDLA) stereo complex is described and their thermal stabilities are evaluated. The hierarchic photochemical patterning of PLLA/PDLA stereo complex honeycomb‐patterned films by UV‐O3 treatment is also demonstrated.
A gas‐permeable cellulose template for microimprint lithography has been synthesized and characterized for the reduction of template damage and gas trapping caused by solvents and oxygen generated from cross‐linked materials. The 5 μm line‐pattern failure of the microimprinted UV cross‐linked liquid materials with 4.7 wt% acetone as a volatile solvent is solved by using the gas‐permeable cellulose template because of its increased oxygen permeability. The gas‐permeable cellulose template also allows the use of volatile solvents with high coating property and solubility into the microimprinted materials instead of the compounds and plastic resins conventionally used in mold injection.
Hydrophobic and super‐hydrophobic materials have many important applications, but most of the artificially hydrophobic and super‐hydrophobic surfaces suffer from poor durability. Herein, a facile method is reported to fabricate robust hydrophobic and super‐hydrophobic polymer films through backfilling the silica colloidal crystal templates with the mixture of fluoropolymer, thermoset hydroxyl acrylate resins, and curing agent. After removal of the template, 3D ordered porous structures are obtained. The obtained polymer films have not only excellent hydrophobic or super‐hydrophobic properties but also good stability against temperatures, acids, and alkalis. Dual ordered porous structure can obviously enhance the hydrophobicity of polymer films compared to unitary one.
The previously introduced process for enzyme‐mediated in situ synthesis and deposition of eumelanin is investigated with covalent immobilization of the tyrosinase. It results in a monolayer structure of non‐coalesced melanin particles, with a film thickness of 5–8 nm. The reaction is self‐terminating due to overlay of the enzymes with particles. The melanin particles are rodlike with lengths down to 6 nm. Isolated melanin structures of such small size have not been observed before and might be a kind of protoparticle in the supramolecular buildup of melanin oligomers. Utilization of melanin particles with such small size can enable nanotechnological applications in the areas of bioelectronics and biosensors.
The introduction of nanodiamond particles (NDs) in silane‐crosslinked polyethylene is found to lead to a notable and systematic deformation of the polymer unit cell. X‐ray diffraction evidence of the existence of a modified crystalline structure in the bulk of the polymer due to the presence of NDs is reported here for the first time. The covalent bonding between NDs and the surrounding macromolecular chains may support that the excessive local stress field ultimately distorts the polymer conformation, yielding a new distorted but still crystalline interface. Supporting data from solid‐state NMR experiments confirm the existence of a modified crystalline interface of about 1–2 nm in all the nanocomposite materials.
Thermal induced solid phase polymer reactions between bisphenol‐A‐based polycarbonate (PC) and polyvinylamine (PVAm) are used to form permanent composite material. The PC–PVAm interface is characterized by infrared (IR) spectroscopy. IR spectra of synthesized reference substances which can be expected after PC–PVAm reaction are recorded and used to identify amidation product structures within the PC–PVAm interphase. Curve fit analysis is performed to isolated sub‐bands. The spectral position of the carbonyl absorption band is a suitable marker for the identification of different amidation products. While the formation of urethane and cyclic Allophanate points to the formation of a co‐polymer cyclic Urea indicates a PC chain scission without binding between both polymer materials.
Nanogels loaded with fluorescent dextran as a model drug are synthesized by the oxidation induced cross‐linking of water soluble redox responsive thiolated poly(amino acid) in miniemulsion without the introduction of any cross‐linker molecule. Two types of high energy methods, namely, ultrasonication and high pressure homogenization (HPH), are compared. Dynamic light scattering and transmission electron microscopy measurements confirm that spherical nanogels in 100–150 nm diameter range are prepared successfully by HPH method. Size and surface charge of the nanogels can easily be controlled by environmental pH. The release of encapsulated drug is triggered by the degradation of nanogels in reducing environment due to the cleavage of disulphide bonds.
下载免费PDF全文