铣削碳纤维复合材料刀具磨损试验研究

采用未涂层和CVD金刚石薄膜涂层两种硬质合金铣刀,对碳纤维复合材料进行铣削试验,使用3D激光扫描镜对刀具磨损形貌和磨损量进行测量,分析了刀具的磨损机理和切削用量对刀具磨损的影响。试验结果表明：后刀面磨损是两种刀具的主要磨损形式,磨损机理为磨料磨损,未涂层硬质合金铣刀同时存在着刀具破损现象;切削速率和背吃刀量对刀具后刀面的磨损影响较为显著;未涂层与CVD金刚石薄膜涂层硬质合金铣刀相比较,后刀面的磨损量保持在2．3—3．8倍之间,从刀具的耐磨性考虑,CVD金刚石薄膜涂层硬质合金铣刀可以用于碳纤维复合材料的生产加工。     

不同铝基体SiC_p/Al复合材料切削力与刀具的磨损研究

对不同增强相体分比、颗粒尺寸和基体材料的Si CP/Al复合材料进行切削试验,分析了铝基体材料和颗粒尺寸对高、低增强相体分比Si C_p/Al复合材料切削力的影响。针对Si C_p/Al复合材料切削力的复杂性,提出用分形维数的方法定量描述切削力波动的复杂程度。对不同铝基体Si C_p/Al复合材料进行刀具磨损试验,研究铝基体对刀具磨损的影响。结果表明:随着增强相体分比和颗粒尺寸的增加,铝基体对切削力的影响减弱;随着增强相体分比增加,颗粒尺寸对于切削力影响有增大趋势;分形维数可以定量描述切削力波动性质,且Si C_p/6063Al切削力波动频率高于Si C_p/2024Al;相对于Si C_p/2024Al,切削Si C_p/6063Al时刀具前刀面粘结磨损加剧而颗粒磨损减少,刀具后刀面磨损程度相对较高。     

超细晶硬质合金刀具切削高温合金试验研究

使用普通晶粒度硬质合金YG8和超细晶硬质合金YG8UF两种材料刀具,分别对GH2132高温合金进行了干式切削试验,对比了两种刀具在不同切削速度条件下的切削力和刀-屑摩擦系数,测定了刀具后刀面的平均磨损宽度VB值,借助扫描电镜观察了刀具后刀面的磨损形貌,同时对刀具的磨损机理进行了分析.结果 表明,晶粒细化可以使切削力降低,刀-屑间平均摩擦系数减小.当切削速度达到65m/min后,超细晶硬质合金刀具YG8UF的使用寿命是普通晶粒度硬质合金刀具YG8的(3～4)倍.超细晶硬质合金刀具比通晶粒度硬质合金刀具具有更好的抗磨料磨损、粘着磨损和扩散磨损性能.     

切削金属基复合材料的刀具

金属基复合材料由于含有硬质增强相而难以切削加工,常规刀具因迅速发生严重的磨料磨损而失效。为此切削加工研究者对各种刀具切削金属复合材料进行了试验。本文对此加以综述。     

微米／纳米复合Ti（C，N）基金属陶瓷刀具切削铸铁的性能研究

利用热压烧结法制备了微米／纳米复合Ti（C,N）／Al2O3金属陶瓷刀具,对研制的三种金属陶瓷刀具（材料编号JT1-JT3）和YG8硬质合金刀具切削铸铁时的切削性能进行了试验研究。结果表明,研制的金属陶瓷刀具适合切削铸铁,其切削性能优于YG8,尤其是JT2刀具不但磨损较小,且加工表面质量较好。分析了刀具的磨损形貌和磨损机理,得出了Ti（C,N）金属陶瓷刀具的主要磨损机理为后刀面磨粒磨损的结论。     

钻削SiCw／LD2、SiCp／LD2复合材料的刀具磨损和表面质量的试验研究

在钻削SiCw/LD2（晶须）、SiCp/LD2(颗粒）增强铝基复合材料的实验过程中,使用不同的刀具材料进行切削性能对比实验,详细讨论了加工复合材料的刀具磨损和表面质量状况。     

PCD刀具切削颗粒增强铝基复合材料时刀具磨损研究

通过高颗粒含量铝基复合材料切削加工时PCD刀具的磨损试验,研究了切削该种材料时PCD刀具的磨损形态及磨损机理。刀具磨损区微观形貌的检测分析结果表明,PCD刀具的磨损形态主要表现为前刀面磨损和后刀面磨损,造成刀具磨损的主要原因是磨料磨损和粘结磨损。采用超声波振动切削技术可减小刀具磨损。     

超声振动铣削碳纤维复合材料刀具磨损研究

采用超声振动铣削和普通铣削对硬质合金铣刀铣削碳纤维复合材料进行试验研究。试验结果表明,在两种加工方式下,刀具的磨损形式主要是后刀面磨损、前刀面磨损和刀刃的破损,其中后刀面的磨粒磨损最严重,前刀面的粘着磨损较弱,当进给量加大或者是主轴转速过高时,很容易发生崩刃。超声振动条件下,刀具的后刀面磨损和前刀面磨损均较弱,且呈现一定的规律性,刀具的耐用度高,相对于普通切削更适合于复合材料的加工。     

高速铣削淬硬钢刀具磨损机理的研究

通过工具显微镜、扫描电镜以及能谱分析的方法对K30刀具高速铣削淬硬钢的磨损形态和磨损机理做了研究,从试验结果看出由于粘结磨损、磨料磨损、扩散磨损以及其他磨损等原因使得硬质合金刀具高速铣削淬硬钢时刀具的磨损主要发生在刀具的后刀面,主要的磨损形态是片状剥落、微崩刃以及边界磨损等,前刀面的磨损和常规切削下磨损形态不一样,主要集中在刀刃处,距离刀刃一段距离有较小剥落现象出现.     

陶瓷刀具高速干切削等温淬火球铁(ADI)磨损性能研究

采用陶瓷刀具(CC650)对等温淬火球墨铸铁(以下简称AD I)进行干式高速切削试验,用带有X射线能谱分析的扫描电镜观察刀具表面的磨损形貌,并对刀具磨损微区和工件表面成分进行定性分析,用X射线衍射仪对刀具、工件和切屑等试样进行物相分析,研究高速切削时陶瓷刀具磨损性能及磨损机制。结果表明:切削速度是影响刀具寿命的主要因素;CC650刀具高速干切削AD I时形成的刀具主后刀面和前刀面的磨损形态基本类似中、低速条件下磨损形态,主要区别在其磨损区域紧靠切削刃,最大磨损部位位于切削刃附近;CC650刀具高速切削AD I时切削温度高,其磨损是机械磨损与化学磨损综合作用的结果,磨损机制主要包括磨料磨损、扩散磨损、粘结磨损和微崩。     

车削加工陶瓷材料时刀具磨损表面形态的研究

分别使用硬质合金刀具、金刚石刀具、立方氮化硼刀具对氟金云母陶瓷及二硅酸锂玻璃陶瓷材料进行车削试验。利用显微镜观察刀具磨损形貌,通过能谱分析研究了刀具的磨损机理。试验结果表明,刀具磨损部位主要集中在刀尖和后刀面,刀具磨损形式主要为磨料磨损和粘结磨损。用硬质合金刀具车削氟金云母陶瓷时,切削深度越小,磨料磨损越严重。     

陶瓷涂层刀具切削灰铸铁的试验研究

为了探究陶瓷涂层刀具涂层材质、基体材质对切削性能的影响,试验采用四种陶瓷涂层刀具连续干切削灰铸铁,测试了切削力和切削温度的变化情况以及后刀面的磨损量和已加工表面的粗糙度。结果表明,在刀具基体同为Si_3N_4的条件下,涂层材质为Ti N/Al_2O_3/Ti C的刀具比Ti N/Al_2O_3的切削性能好;在涂层材质同为Ti N的条件下,刀具基体Al_2O_3/Ti CN比Al_2O_3/Ti C的切削性能好。研究发现:四种陶瓷涂层刀具前刀面磨损形式均为微崩刃和月牙洼,后刀面磨损形式均为磨粒磨损和粘着磨损,涂层的磨损形式均为剥落和扩散磨损。     

Failure mechanisms of a PCD tool in high-speed face milling of Ti–6Al–4V alloy

High-speed milling tests were carried out on Ti–6Al–4V titanium alloy with a polycrystalline diamond (PCD) tool. Tool wear morphologies were observed and examined with a digital microscope. The main tool failure mechanisms were discussed and analyzed utilizing scanning electron microscope, and the element distribution of the failed tool surface was detected using energy dispersive spectroscopy. Results showed that tool flank wear rate increased with the increase in cutting speed. The PCD tool is suitable for machining of Ti–6Al–4V titanium alloy with a cutting speed around 250 m/min. The PCD tool exhibited relatively serious chipping and spalling at cutting speed higher than 375 m/min, within further increasing of the cutting speed the flank wear and breakage increased greatly as a result of the enhanced thermal–mechanical impacts. In addition, the PCD tool could hardly work at cutting speed of 1,000 m/min due to the catastrophic fracture of the cutting edge and intense flank wear. There was evidence of workpiece material adhesion on the tool rake face and flank face in very close proximity to the cutting edge rather than on the chipped or flaked surface, which thereby leads to the accelerating flank wear. The failure mechanisms of PCD tool in high-speed wet milling of Ti–6Al–4V titanium alloy were mainly premature breakage and synergistic interaction among adhesive wear and abrasive wear.     

TiAlN涂层硬质合金刀具铣削35CrMoSiV钢的切削性能研究

采用有和无PVD TiAlN涂层的细晶硬质合金铣刀对35CrMoSiV合金钢进行了干式端面铣削试验。分别测量了有、无涂层情况下铣刀后刀面径向磨损量和加工槽的表面粗糙度,通过光学显微镜观察了切屑,利用扫描电子显微镜(SEM)和电子能谱(EDX)分析了后刀面的磨损形态。研究结果表明:TiAlN涂层明显提高了硬质合金刀具的切削性能;硬质合金刀具后刀面磨损机制主要为粘着磨损和磨粒磨损,而涂层损伤是粘着磨损、剥层和氧化磨损共同作用的结果;在正常工作区内,提高铣削的转速和进给量,有利于减轻刀具的粘着,提高切削效率和质量。     

ZTA陶瓷刀具连续切削淬硬T10A时的切削性能研究

研究两种自主研制的新型ZTA(Al2O3/Zr O2)陶瓷刀具切削淬硬T10A时的切削性能。刀具后刀面磨损量随切削深度和切削速度的增加而增大;刀具的主要磨损形态为后刀面磨损;主要磨损机理为后刀面磨粒磨损和部分粘结磨损。     

Experimental Study on Wear Characteristics of PCBN Tool with Variable Chamfered Edge

Owing to heavy dynamic and thermal loads, PCBN tools are seriously worn during hard cutting, which largely constrains the improvement of their machining performance. Therein, the chamfered structure of a cutting edge has a notable influence on the tool wear. Thus, a comparative study was carried out on the wear morphology and wear mechanism of PCBN tools with either a variable chamfered edge or an invariable chamfered edge. The results indicate that, for a PCBN tool with a variable chamfered edge, the rake wear area is far from the cutting edge and slowly extends toward it. A shallow large-area crater wear occurs on the rake face, and the flank wear area has a long triangular shape with a smaller wear area and width, and the cutting edge remains in a good state during the cutting process. In contrast, for a PCBN tool with an invariable chamfered edge, a deep small-area crater appears on the rake face,and the wear area is close to the cutting edge and quickly extends toward it. Thus, it is easy for chips to accumulate in the crater, resulting in large-area and high-speed wear on the flank face. In addition, the tool shows a weak wear resistance. In the initial wear stage, the rake wear mechanism of the two cutting tools is a mixture of abrasive, oxidation, and other types of wear, whereas their flank wear mechanism is dominated by abrasive wear. With an aggravation of the tool wear, the oxidation and di usion wear mechanism are both increasingly strengthened. The rake wear of the cutter with a variable chamfered edge showed an obvious increase in the oxidation and di usion wear, as did the flank wear of the cutter with an invariable chamfered edge. This study revealed the wear mechanism of the PCBN tool with a variable chamfered edge and provided theoretical and technological support for its popularization and application in the machining of high-hardness materials.     

铁基粉末冶金材料的高速干切削试验研究

用陶瓷刀具、涂层刀具和硬质合金刀具进行了铁基粉末冶金零件的干切削对比试验,研究了切削速度、切削深度以及进给速度与刀具耐用度和加工表面粗糙度的关系,分析了陶瓷刀具的磨损机理。结果表明所选用陶瓷刀具的切削性能明显优于涂层刀具和硬质合金刀具;陶瓷刀具前刀面主要磨损形式为月牙洼磨损与剥落,后刀面的主要磨损原因为磨粒磨损;认为陶瓷刀具更适合用于粉末冶金零件的切削加工。     

Crater and flank wear resistance of cutting tools having micro textured surfaces

We have proposed cutting tools with various textured surfaces to increase cutting tool life. Our previous studies have developed cutting tools having periodical stripe-grooved surfaces on their rake face formed using femtosecond laser technology, which displayed high crater wear resistance in cutting of steel materials. In this study, the mechanism for suppressing the crater wear on the tool surface and the relationship between texture dimensions and wear resistance were investigated to provide a guideline for developing tools with textured surfaces. Furthermore, we newly introduced the textured surfaces into a flank face of cutting tools to improve flank wear resistance. Face milling experiments on steel materials exhibited that the newly developed tool having the textured flank face significantly reduced the flank wear. Moreover, the influences of texture dimensions and cutting conditions on the flank wear resistance were also discussed.     

激光超声复合切削硬质合金的刀具磨损及其对工件表面质量的影响

基于激光加热辅助切削和超声椭圆振动切削提出了激光超声复合切削加工工艺。采用聚晶立方氮化硼(PCBN)刀具对YG10硬质合金进行了常规切削,超声椭圆振动切削,激光加热辅助切削和激光超声复合切削对比试验。检测了刀具磨损量、刀具磨损形貌、工件表面粗糙度以及工件表面形貌,并通过扫描电镜(SEM)对刀具磨损区域进行了能谱分析,同时研究了激光超声复合切削硬质合金时PCBN刀具的磨损及其对工件表面质量的影响。最后,与常规切削、超声振动切削及激光加热辅助切削进行了对比试验。结果表明:激光超声复合切削时刀具使用寿命显著增加,加工后的工件表面粗糙度平均值分别降低了79%、60%和64%,且工件表面更加平整光滑。激光超声复合切削硬质合金时,PCBN刀具的前刀面磨损表现为平滑且均匀的月牙洼磨损,后刀面磨损表现为较窄的三角形磨损带和较浅的凹坑和划痕;刀具的失效机理主要为黏接磨损、氧化磨损和磨粒磨损的综合作用。