Plasma spraying of Al2O3 and Al2O3Y2O3

A microstructural study has been carried out of plasma-sprayed Al₂O₃ and mixed and sintered Al₂O₃Y₂O₃. In order to ascertain the degree of metastability achieved by plasma spraying, these results are compared with a similar experiment utilizing a CO₂ laser for melting and the hammer-and-anvil technique for quenching of the same materials. X-ray diffraction methods were used to determine the obtained phases and crystal structures. In addition, transmission electron microscopy was used to confirm the phases present and to study their morpology. The porosity was studied with both mercury intrusion porosimetry and small angle neutron scattering. The addition of Y₂O₃ is shown to decrease the porosity from 15% to 7.5%. Adhesion is likewise related to the addition of Y₂O₃ and it is seen that adhesion of the mixture is measurably improved over that of pure Al₂O₃. The implication of these results is discussed.     

Surface tension of PbO-B2O3 and Bi2O3-B2O3 glass melts

The surface tensions of xPbO-(100?x) B₂O₃ (x = 30–80 mol%) and xBi₂O₃-(100?x) B₂O₃ (x = 0–100 mol%) melts were measured using the ring method over the temperature range 973 to 1373 K. The compositional and temperature dependences of surface tension were investigated. Addition of PbO and Bi₂O₃ to B₂O₃ increased the surface tensions of their respective PbO-B₂O₃ and Bi₂O₃-B₂O₃ melts. The surface tension showed a maximum at 60 mol% PbO in the PbO-B₂O₃ melts and at 70–80 mol% Bi₂O₃ in the Bi₂O₃-B₂O₃ melts. The temperature coefficient of surface tension was examined on the basis of its relationship to the structure, and it was suggested that the temperature coefficient of surface tension decreases with an increasing content of four-coordinated boron.     

Preparation of pressureless-sintered SiC-Y2O3-Al2O3

Sintering additives were prepared from aluminium hydroxide and yttrium hydroxide. These additives were soluble in water and resulted in a binder. A -SiC powder was mixed with the additive solution and sintered at 2150° C without pressure. The oxides formed from the additive promoted sintering. The sintered body contained no pores. Aluminium, silicon, and yttrium oxide were precipitated in the sintered body.     

Microstructure and Strength of Al2O3/Al2O3 Joints Bonded with ZnO-Al2O3-B2O3-SiO2 Glass-Ceramic

ZnO-Al2O3-B2O3-SiO2 （ZABS） glass powder was used as interlayer to join alumina ceramics. The effect of joining temperature on the microstructure and strength of joints was investigated. The results showed that the ZABS glass can react with alumina substrate to form a layer of ZnAl2O4 at Al2O3/glass interface. Bending test exhibited that low joining temperature （1150℃） led to low joint strength due to the formation of pores in the interlayer, originated by high viscosity of the glass. High joining temperature （1250 ℃） also resulted in low joint strength, because of large CTE （coefficient of thermal expansion） mismatch between amorphous interlayer and alumina substrate. Therefore, only when the joining temperature was appropriate （1200℃）, defect-free interface and high joint strength can be obtained. The optimum joint strength reached 285 MPa, which was the same as the base material strength.     

Al2O3/Al2O3 Joint Brazed with Al2O3-particulate-contained Composite Ag-Cu-Ti Filler Material

1.IntroductionTo improve the mechanical properties and relieve mis-matches between the filler metals and base materials,the particulates of superalloys,ceramic or carbon fiberswere added into the conventional brazing filler metal toform composite filler material.The method has beenused in aero-engine component repairing[1,2],fine castcomponent joining[3],wide clearance butt jointing[4],ce-ramic brazing[5,6]and electronic package[7].However,the method was used mostly in metal brazing.The mi-cro…     

Solid state reactions in the Fe2O3-CaCO3-In2O3 system

The kinetics of solid-state reactions of powdered reactants were investigated by X-ray and by differential thermogravimetry in a magnetic field. Measurements revealed mutual diffusion of the Fe³⁺ and In³⁺ ions in the Fe₂O₃-In₂O₃ system heat treated for 3 h at 700 to 1400° C. Diffusion of indium into the Fe₂O₃ lattice caused a shift of the Curie temperature of the antiferromagnetic iron oxide towards lower temperatures. Only Caln₂O₄ was found between CaCO₃ and In₂O₃ up to 1400° C. Also, in the Fe₂O₃-CaCO₃-In₂O₃in system, the reaction started with the mutual diffusion of iron and indium and the forming of CaFe₂O₄. End-products were the magnetic -Ca₄Fe₁₄O₂₅ and CaFe₄O₇, and the non-magnetic CaFe₅O₇, depending on the In³⁺ concentration. Indium stabilized the magnetic calcium-iron oxide structures, shifting their Curie temperatures towards lower values.     

Rare-gas mobility in some anisotropic ceramic oxides: Al2O3, Cr2O3, Fe2O3, TiO2, U3O8

The mobility of the inert gases xenon or radon in five anisotropic oxides (hexagonal corundum Al₂O₃, Cr₂O₃, Fe₂O₃, tetragonal rutile TiO₂, and orthorhombic U₃O₈) was studied. The gases were introduced by ion bombardment. The oxides were in the form of powders, sinters, or single crystals. Normal volume diffusion was found at low gas concentration, the activation energies in kilocalories per mole being 85 for Al₂O₃, 73±5 for Cr₂O₃, 68±5 for Fe₂O₃, 78±5 for TiO₂, and 85±8 for U₃O₈, and the pre-exponential termsD ₀ falling into the ideal range of about 3×10^–1±1 cm²/sec. Structural radiation damage, the annealing of which coincided with gas release at low temperatures, and, in some cases, retardation of the gas release were found at higher gas concentrations. Some evidence is presented that grain boundaries, pre-existing vacancy clusters, and dislocation loops may act as trapping sites for gas atoms (or bubbles) and may be stabilised after trapping of the gas.     

Wetting of gold by Bi2O3-B2O3 melts

The wetting of gold by Bi₂O₃-B₂O₃ melts has been studied by the sessile drop method, with the sample and substrate heated separately before being brought into contact. Only the melts containing 18.5 and 33.3 mol % B₂O₃ were found to have steady-state contact angles.     

Creep of Cr2O3 and yttrium doped Cr2O3

Abstract

Compressive creep tests of pure and Y doped Cr₂O₃ from 1217 to 1417°C have shown that the presence of Y substantially increases diffusional flow rates. It is suggested that this increase in deformation rate may account, in part, for the empirical evidence that improved adherence to the underlying metal is provided by Y containing scales compared with pure scales.

MST/819     

Some physical properties of V2O5-Fe2O3 and V2O5-Fe2O3-Li2O systems

Various methods have been used to study the physical properties of the V₂O₅-Fe₂O₃ and V₂O₅-Fe₂O₃-Li₂O systems, including X-ray, electron microscope, Mössbauer effect, NMR and thermogravimetric measurements. The iron ions are approximately equally distributed in substitutional and interstitial sites in the V₂O₅ lattice. The maximum number of iron ions dissolved in the V₂O₅ matrix corresponds to 4 mol % Fe₂O₃. In all the samples a quantity of Fe₂O₃ which has not been included in lattice is observed. The V₂O₅-Fe₂O₃ and V₂O₅-Fe₂O₃-Li₂O systems are formed from solid solutions mixed with very small Fe₂O₃ particles. The analysis of the charge compensation of iron ions suggests that V₂O₅ is a quasi-amorphous semiconductor. Irradiation of V₂O₅-based samples with an electron beam induces the V₂O₅ platelets to convert to the VO _x phase.