Mechanical and piezo‐resistive properties of styrene–butadiene–styrene copolymer covalently modified with graphene/styrene–butadiene–styrene composites

As novel piezoelectric materials, carbon‐reinforced polymer composites exhibit excellent piezoelectric properties and flexibility. In this study, we used a styrene–butadiene–styrene triblock copolymer covalently grafted with graphene (SBS‐g‐RGO) to prepare SBS‐g‐RGO/styrene–butadiene–styrene (SBS) composites to enhance the organic solubility of graphene sheets and its dispersion in composites. Once exfoliated from natural graphite, graphene oxide was chemically modified with 1,6‐hexanediamine to functionalize with amino groups (GO–NH₂), and this was followed by reduction with hydrazine [amine‐functionalized graphene oxide (RGO–NH₂)]. SBS‐g‐RGO was finally obtained by the reaction of RGO–NH₂ and maleic anhydride grafted SBS. After that, X‐ray diffraction, X‐ray photoelectron spectroscopy, Raman spectroscopy, scanning electron microscopy, transmission electron microscopy, thermogravimetric analysis, and other methods were applied to characterize SBS‐g‐RGO. The results indicate that the SBS molecules were grafted onto the graphene sheets by covalent bonds, and SBS‐g‐RGO was dispersed well. In addition, the mechanical and electrical conductivity properties of the SBS‐g‐RGO/SBS composites showed significant improvements because of the excellent interfacial interactions and homogeneous dispersion of SBS‐g‐RGO in SBS. Moreover, the composites exhibited remarkable piezo resistivity under vertical compression and great repeatability after 10 compression cycles; thus, the composites have the potential to be applied in sensor production. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46568.     

Preparation and properties of bitumen modified with the maleic anhydride grafted styrene‐butadiene‐styrene triblock copolymer

A procedure to improve the properties of styrene‐butadiene‐styrene (SBS) copolymer modified bitumen by grafting of maleic anhydride (MAH) onto SBS in the presence of benzoyl peroxide (BPO) as initiator was proposed. The effects of the grafting degree (GD) on the properties of modified bitumen were investigated. FTIR spectroscopy was employed to verify the grafting of MAH onto SBS. The GD of MAH onto SBS was determined by a back titration procedure. To assess the effects of the GD of grafted SBS on properties of modified bitumen, the softening point, penetration, ductility, elastic recovery, penetration index, viscosity, storage stability, and dynamic shear properties were tested. Experimental results indicated that the SBS grafted with maleic anhydride (SBS‐g‐MAH) copolymer was successfully synthesized by solvothermal method, and different GD of the SBS‐g‐MAH was obtained by control the MAH concentration. The GD of the MAH onto SBS has great effect on the rheological properties of the modified bitumen, and the high temperature performance and storage stability of modified bitumen were improved with the GD of the MAH onto SBS increasing. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

The influence of styrene–butadiene diblock copolymer on styrene–butadiene–styrene triblock copolymer viscoelastic properties and product performance

The effects of the styrene–butadiene (SB) diblock copolymer on the viscoelastic properties of styrene–butadiene–styrene (SBS) triblock copolymers were examined in both in the the neat state and within specific product applications. The addition of the SB diblock copolymer into a pure SBS triblock copolymer resulted in a significant decrease in the plateau storage modulus and a quantitative linear rise in tan delta. In a pure triblock, in which all endblocks are anchored in polystyrene domains, all entanglements are physically trapped. The SB diblock embodies untrapped polybutadiene endblocks that are able to relax stress by chain reptation through the rubbery polybutadiene matrix. The SB diblock copolymer quantitatively lowered the microphase separation temperature (MST) of the SBS triblock copolymer. These changes in linear viscoelastic behavior manifest themselves into a reduction in the efficiency and performance of the SBS triblock copolymer in asphalt pavement binders and hot-melt adhesive blends. Specifically, the SB diblock diminished the complex shear modulus and elasticity of a polymer-modified asphalt, which translated into lower predicted rutting specification values. The increase in diblock content altered the viscoelastic response of the hot-melt adhesive blend, translating into a reduction in the shear holding power and shear adhesion failure temperature. The lack of network participation, coupled with the relaxation of the polybutadiene endblocks, accounts for the lower strength and greater temperature susceptibility of the diblock-containing systems. © 1995 John Wiley & Sons, Inc.     

Properties of acrylonitrile–butadiene–styrene/polycarbonate blends with styrene–butadiene–styrene block copolymer

The importance of alloys and blends has increased gradually in the polymer industry so that the plastics industry has moved toward complex systems. The main reasons for making polymer blends are the strengthening and the economic aspects of the resultant product. In this study, I attempted to improve compatibility in a polymer blend composed of two normally incompatible constituents, namely, acrylonitrile–butadiene–styrene (ABS) and polycarbonate (PC), through the addition of a compatibilizer. The compatibilizing agent, styrene–butadiene–styrene block copolymer (SBS), was added to the polymer blend in ratios of 1, 5, and 10% with a twin‐screw extruder. The morphology and the compatibility of the mixtures were examined by scanning electron microscopy and differential scanning calorimetry. Further, all three blends of ABS/PC/SBS were subjected to examination to obtain their yield and tensile strengths, elasticity modulus, percentage elongation, Izod impact strength, hardness, heat deflection temperature, Vicat softening point, and melt flow index. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2521–2527, 2004     

Amphiphilic styrene–butadiene–styrene triblock copolymer grafted with polyoxyethylene

A styrene–butadiene–styrene triblock copolymer (SBS) was grafted with polyoxyethylene via a ring‐opening reaction of an epoxidized styrene–butadiene– styrene triblock copolymer (ESBS) with monocarboxylic‐group‐terminated methoxypoly(ethylene glycol) (CMPEG). The latter was prepared through the esterification of methoxypoly(ethylene glycol) with maleic anhydride. The optimum conditions for the preparation of the graft copolymer were studied. The graft copolymer was characterized with Fourier transform infrared spectrophotometry. Its water absorbency, oil absorbency, emulsifying property, phase‐transfer catalysis property in the Williamson solid–liquid reaction, and use as a compatibilizer in the blending of SBS with oil‐resistant chlorohydrin rubber (CHR) were also studied. The optimum conditions were a CMPEG/epoxy group molar ratio of 1.5, an N,N‐dimethyl aniline/ESBS concentration of 5 wt %, and an ESBS concentration of 12–14 g/100 mL at 75–80°C for 10 h. The polyoxyethylene content could reach 0.27 mmol/g. The graft copolymer absorbed a certain amount of water, fairly resisted kerosene, and possessed good emulsifying and phase‐transfer catalysis properties, both of which were enhanced with increasing polyoxyethylene graft content. The graft copolymer could be used as a compatibilizer for a blend of SBS and CHR. A 3 wt % concentration of the graft copolymer based on a 50/50 blend could increase both the tensile strength and ultimate elongation of the blend about 1.7 times. The blend behaved like an oil‐resistant thermoplastic elastomer. Scanning electron microscopy demonstrated the improved compatibility of the two components by the graft copolymer. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Bulk modification of styrene–butadiene–styrene triblock copolymer with maleic anhydride

The bulk modification of SBS rubber with maleic anhydride in a mixing chamber of a Haake rheomixer was studied. The effect of temperature, maleic anhydride, and benzoyl peroxide concentrations on the grafting efficiency was evaluated. High grafting efficiency was achieved when the ratio of peroxide and maleic anhydride concentration was high. On the other hand, on this condition high insoluble fraction was generated. The addition of a diamine, 4,4′‐diaminediphenylmethane to the reaction mixture minimizes the amount of insoluble polymer. However, the grafted MAH content also decreases. The graft copolymer was characterized by infrared spectroscopy and the grafting extension was determined by titration. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2953–2960, 2002; DOI 10.1002/app.10355     

Blends of styrene–butadiene–styrene triblock copolymer and isotactic polypropylene: morphology and thermomechanical properties

A set of blends of styrene–butadiene–styrene triblock copolymer (SBS) and isotactic polypropylene (i‐PP) in a composition range 0–100 % polypropylene by weight was prepared in a twin screw extruder. The morphology of the blends has been studied by transmission electron microscopy. The blends present phase separation. Dynamic mechanical measurements show an improvement of the mechanical properties of SBS when i‐PP is the dispersed phase. This reinforcing effect can be observed even at high temperatures when i‐PP is in the rubbery state. The mechanical properties of the blends have been interpreted using Takayanagi's block model. The melting and crystallization behaviour of the i‐PP in the blends has been studied by differential scanning calorimetry. The fractionated crystallization phenomenon has been observed in the blends where i‐PP forms the dispersed phase. The results are consistent with the morphology shown by the blends, in particular, with its phase inversion, which occurs at a composition near to 50% i‐PP. © 2000 Society of Chemical Industry     

Physical and rheological properties of crumb rubber/styrene–butadiene–styrene compound modified asphalts

In order to improve the storage stability and tenacity of crumb rubber modified (CRM) asphalt, CRM compound modified asphalt was prepared by the addition of styrene–butadiene–styrene (SBS) and sulfur. The addition of SBS improved the tenacity of CRM asphalt, due to the formation of a dense polymer network. The storage stability of crumb rubber (CR)/SBS‐modified (CRSM) asphalt was improved by the addition of sulfur. The rheological tests confirmed the effect of SBS and sulfur on the physical properties of CRM asphalt to some extent and showed the susceptibility of CR/SBS/sulfur‐modified (CRSSM) asphalt to dynamic shearing. The morphology observation showed the compatibility of CRSM asphalt was improved greatly by vulcanization. POLYM. COMPOS., 38:1918–1927, 2017. © 2015 Society of Plastics Engineers     

Effect of styrene–isoprene–styrene,styrene–butadiene–styrene,and styrene–butadiene–rubber on the mechanical,thermal, rheological,and morphological properties of polypropylene/polystyrene blends

The mechanical, thermal, rheological, and morphological properties of polypropylene (PP)/polystyrene (PS) blends compatibilized with styrene–isoprene–styrene (SIS), styrene–butadiene–styrene (SBS), and styrene–butadiene–rubber (SBR) were studied. The incompatible PP and PS phases were effectively dispersed by the addition of SIS, SBS, and SBR as compatibilizers. The PP/PS blends were mechanically evaluated in terms of the impact strength, ductility, and tensile yield stress to determine the influence of the compatibilizers on the performance properties of these materials. SIS‐ and SBS‐compatibilized blends showed significantly improved impact strength and ductility in comparison with SBR‐compatibilized blends over the entire range of compatibilizer concentrations. Differential scanning calorimetry indicated compatibility between the components upon the addition of SIS, SBS, and SBR by the appearance of shifts in the melt peak of PP toward the melting range of PS. The melt viscosity and storage modulus of the blends depended on the composition, type, and amount of compatibilizer. Scanning electron microscopy images confirmed the compatibility between the PP and PS components in the presence of SIS, SBS, and SBR by showing finer phase domains. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 266–277, 2003     

Radiation-induced graft polymerization of 4-vinyl pyridine to styrene–butadiene–styrene triblock copolymer

The radiation-induced graft polymerization of 4-vinyl pyridine to styrene–butadiene–styrene triblock copolymer (SBS) was investigated. Relations between the rate of grafting and the dose rate when SBS was irradiated in 4-vinyl pyridine–methanol solution, and between the rate of grafting and 4-vinyl pyridine concentration of 4-vinyl pyridine–methanol solution have been investigated. An experiment that had been carried out on SBS immersed in various 4-vinyl pyridine concentration of 4-vinyl pyridine–methanol solutions showed that the extent of swelling of SBS by the various 4-vinyl pyridine–methanol solutions increased with increasing 4-vinyl pyridine concentration. The largest rate was found at 20 vol % 4-vinyl pyridine–methanol solution. The rate was smaller at the volume percent of 4-vinyl pyridine higher or lower than 20 vol %. On the assumption that the theory of homogeneous homopolymerization could be applied to this grafting reaction, the value of k_p²/k_t was obtained, where k_p and k_t are the propagation and termination constant, respectively. The value of k_p²/k_t greatly decreased with increasing adsorbed concentration of vinyl pyridine–methanol solution. This decrease of k_p²/k_t was explained by the fact that 4-vinyl pyridine and methanol absorbed in SBS acted as a plasticizer which increased the molecular motion of the polymer. The solvent effect on the graft polymerization was also investigated. The result was explained by solubility parameter. When the chosen solvent had better solubility with the polymer, the degree of grafting was smaller. That was connected with the extent of the polymer chain mobility.     

Compatibility effect of radiation‐grafting‐functionalized styrene–butadiene–styrene on polyamide 6/styrene–butadiene–styrene blends

Styrene–butadiene–styrene (SBS) was grafted with dibutyl maleate (DBM), methacrylic acid (MAA), or maleic anhydride (MAH) by ⁶⁰Co γ‐rays. The grafted SBS was blended with polyamide 6 (PA6). The compatibility of the PA6/SBS blends was studied with scanning electron microscopy and rheological measurements. The results showed significant improvement in the compatibility of PA6 blended with MAH‐ or MAA‐grafted SBS, with the former being more effective, whereas grafting DBM was ineffective in this respect. Mechanisms of the compatibility enhancement and ineffectiveness are discussed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Grafting of N‐carbamyl maleamic acid onto a styrene–butadiene–styrene copolymer

A styrene–butadiene–styrene block copolymer (SBS) was functionalized with N‐carbamyl maleamic acid (NCMA) using two peroxide initiators with the aim of grafting polar groups onto the molecular chains of the polymer. The influence of the concentration of benzoyl peroxide (BPO) and 2,5‐dimethyl, 2,5‐diterbuthylperoxihexane (DBPH) was studied. The concentration of peroxy groups ranged between 0.75 and 6 × 10^?4 mol % while the concentration of NCMA was constant at 1 wt %. The reaction temperature was chosen according to the type of peroxide employed, being 140°C for BPO and 190°C for DBPH. FTIR spectra confirmed that NCMA was grafted onto the SBS macromolecules. It was found that the highest grafting level was achieved at a concentration of peroxy groups of about 3 × 10^?4 mol %. Contact angle measurements were used to characterize the surface of the SBS and modified polymers. The contact angle of water drops decreased with the amount of NCMA grafted from 95°, the one corresponding to the SBS, to about 73°. T‐peel strength of polymer/polyurethane adhesive/polymer joints made with the modified polymers was larger than those prepared with the original SBS. The peel strength of SBS modified with 1.5 and 3 × 10^?4 mol % of peroxy groups from BPO were five times larger than that of the original SBS. The materials modified using BPO showed peel strengths higher than the ones obtained with DBPH. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4468–4477, 2006     

Effects of molecular weight and arm number on properties of star‐shape styrene–butadiene–styrene triblock copolymer

A star‐shape styrene–butadiene–styrene triblock copolymer SBS (802) was synthesized and fractionated into four fractions coded as 802‐F1 (four arms), 802‐F2 (two arms), 802‐F3 (one arm), and 802‐F4 by repeating fractional precipitation. Their weight‐average molecular weight (M_w) was measured by size‐exclusion chromatography combined with laser light scattering to be 16.0 × 10⁴, 8.2 × 10⁴, 4.3 × 10⁴, and 1.19 × 10⁴, respectively. The samples were, respectively, compression‐molded and solution‐cast to obtain the sheets coded as 802C, 802‐F1C, 802‐F2C, and 802S, 802‐F1S, 802‐F2S. The structures and mechanical properties of the sheets were characterized by ¹H‐NMR, scanning electron microscope, wide‐angle X‐ray diffractometer, tensile testing, and dynamic mechanical thermal analysis. The results indicated that the compression‐molded 802‐F1C exhibited the higher tensile strength (σ_b, 28.4 MPa) and elongation at break (ε_b, 1610%), and its optical transmittance is much higher than those of 802C and 802‐F2C. This work revealed that the star‐shape SBS with four arms could be helpful in the enhancement of the properties as a result of good miscibility of the compression‐molded SBS sheets. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 832–840, 2005     

Mechanical properties of styrene–butadiene–styrene block copolymer composites filled with calcium carbonate treated by liquid polybutadienes

The factors influencing the mechanical properties of styrene–butadiene–styrene block copolymer (SBS) composites filled with liquid polybutadiene (LB)‐surface‐treated calcium carbonate (CaCO₃) were investigated with respect to the molecular structure of the LB, the amount of the LB adsorbed on the CaCO₃ surface, the heat treatment conditions, and the surface treatment method. The mechanical properties, such as the modulus, tensile strength at break, tear strength, storage modulus, and tension set, of the SBS composites were improved remarkably through the filling of CaCO₃ surface‐treated with a carboxylated LB with a high content of 1,2‐double bonds. The heat treatment of LB–CaCO₃ in air was also effective in enhancing such properties. When SBS, CaCO₃, and LB were directly blended (with the integral blend method), secondary aggregation of CaCO₃ took place, and the mechanical properties of the composite were significantly lower. In the integral blend method, LB functioned as a plasticizer. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Photodegradation and stabilization of styrene–butadiene–styrene rubber

Photooxidative degradation and stabilization of a polystyrene–block–polybutadiene–block–polystyrene thermoplastic elastomer using a polychromatic UV light in air at 60°C has been studied by monitoring the appearance of the hydroxyl and carbonyl groups in Fourier transform infrared spectroscopy. The extent of photooxidative degradation in different samples has been compared. The rate of photooxidation was also estimated in the presence of different concentrations of 2,6‐di‐tert‐butyl‐4‐methylphenol [BHT], 2‐(2′‐hydroxy‐5′‐methylphenyl)benzotriazole [Tinuvin P] and tris(nonylphenyl) phosphite [Irgafos TNPP], and 1,2,2,6,6‐pentamethyl piperidinyl‐4‐acrylate was grafted onto the surface of the SBS film. The kinetic evolution of the oxidative reaction was determined. The morphological changes upon irradiation in the solution cast SBS films were studied by scanning electron microscopy. Based on the experimental data a suitable photooxidative degradation mechanism also has been proposed. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1097–1102, 2000     

Novel method for preparation of quaternary ammonium ionomer from epoxidized styrene–butadiene–styrene triblock copolymer and its use as compatibilizer for blending of styrene–butadiene–styrene and chlorosulfonated polyethylene

A novel method for the preparation of a quaternary ammonium ionomer of styrene–butadiene–styrene triblock copolymer (SBS) was developed by a ring‐opening reaction of epoxidized SBS with triethylamine hydrochloride in the presence of a phase transfer catalyst. The optimum conditions were studied. The ionomer was characterized by quantitative analysis, IR spectroscopy, and ¹H‐NMR spectroscopy. Its water absorbency, oil absorbency, dilute solution viscosity, and use as a compatibilizer for the blending of SBS and chlorosulfonated polyethylene (CSPE) were investigated. The results showed that, under optimum conditions, the epoxy groups can be completely converted to the quaternary ammonium groups. The IR spectrum did not exhibit the absorption peak for quaternary ammonium groups, whereas the ¹H‐NMR spectrum and titration method demonstrated it. With increasing ionic group content, the water absorbency of the ionomer increased whereas its oil absorbency decreased. These indicated the amphiphilic character of the SBS ionomer. The dilute solution viscosity of the ionomer in toluene/methanol (9/1) solvent increased with increasing quaternary ammonium group content. The ionomer was used as a compatibilizer for the blends of SBS and CSPE. The addition of a small amount of the ionomer to the blend enhanced the mechanical properties of the blends: 2 wt % ionomer based on the blend increased the tensile strength and ultimate elongation of the blend nearly 2 times. The blends of equal parts SBS and CSPE behaved as oil‐resistant thermoplastic elastomers. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1975–1980, 2006     

Positron annihilation lifetime spectroscopy for miscibility investigations of styrene–butadiene–styrene copolymer/polystyrene blends

The free volume parameters of styrene–butadiene–styrene copolymer/polystyrene (SBS/PS) blends were investigated with positron annihilation lifetime spectroscopy (PALS) in this study. The behaviors of free volume distribution, average free volume, and relative fractional free volume revealed the difference of interfacial miscibility. Based on different models, inter‐chain interaction parameter β, geometric factor γ, and hydrodynamic interaction parameter α obtained from free volume data were employed to further determine the effect of molecular architecture and styrene content on the miscibility. The results suggest the better miscibility in star‐shaped SBS/PS blends than that of corresponding linear SBS/PS systems, even than that of systems containing more styrene unit. In addition, differential scanning calorimetry, dynamic mechanical analysis, and scanning electron microscopy, which are sensitive to heterogeneities in larger domain size, give different results of miscibility from free volume data. It should be attributed the difference of characterization scale. The mechanical property corroborates the results of miscibility. POLYM. ENG. SCI., 54:785–793, 2014. © 2013 Society of Plastics Engineers     

Preparation,characterization, and some properties of ionomers from a sulfonated styrene–butadiene–styrene triblock copolymer without gelation

The conditions for the sulfonation of a highly unsaturated styrene–butadiene–styrene triblock copolymer (SBS) in cyclohexane containing a small amount of acetone with acetyl sulfate made by sulfuric acid and acetic anhydride without gelation were studied. After neutralization with metallic ions, the ionomers were characterized with IR spectrophotometry, dynamic mechanical analysis, and transmission electron microscopy. The melt flow, solution properties, and mechanical properties of the ionomers were studied. The results showed that gelation occurred during the sulfonation of SBS in cyclohexane at a 5–10% concentration without acetone, whereas in the presence of 5–10 vol % acetone, sulfonation proceeded smoothly without gelation. Transmission electron microphotographs of the lead ionomer indicated the presence of ionic domains. A dynamic mechanical spectrum showed the presence of three transition temperatures: ?82.9, 68, and 96.5°C. The melt viscosity of the ionomer increased with the sulfonate content. The melt viscosity of the different ionomers neutralized with different cations seemed to decrease with decreasing ionic potential for both monovalent cations and divalent cations The solution viscosity of the sodium‐sulfonated ionomer increased with increasing sulfonate content. The ionomer still behaved as a thermoplastic elastomer and showed better mechanical properties than the original SBS. The tensile strength of the different ionomers decreased as follows. For the monovalent cations, it decreased with decreasing ionic potentials: Li⁺ > Na⁺ > K⁺. For the divalent cations, it decreased with increasing ionic potentials: Pb²⁺ > Zn²⁺ > Mg²⁺. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1398–1404, 2005     

Effect of styrene–isopren–styrene addition on the recycled polycarbonate/acrylonitrile–butadiene–styrene polymer blends

Interfacial agents as compatibilizers have recently been introduced into polymer blends to improve microstructure and mechanical properties of thermoplastics. In this way, it is possible to prepare a mixture of polymeric materials that can have superior mechanical properties over a wide temperature range. In this study, an incompatible blend of Polycarbonate (PC) and Acrylonitrile Butadiene Styrene (ABS) Copolymer were made compatible by addition of 5, 10, and 20% Styrene–Isopren–Styrene Copolymer (SIS). The mixing operation was conducted using a twin‐screw extruder. The morphology and the compatibility of the mixtures were examined by SEM and DSC techniques. Furthermore, the elastic modulus, tensile and yield strengths, percentage elongation, hardness, melt flow index, Izod impact resistance, heat deflection temperature (HDT), Vicat softening point values of polymer alloys of various ratios were determined. It was found that addition of SIS to the structures decreased the tensile strength, yield strength, elastic modulus, and hardness, whereas it increased Izod impact strength and percentage elongation values. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 559–566, 2006