Exfoliation targeted toughness enhancement in polypropylene‐blend‐ montmorillonite nanocomposites

BACKGROUND: Both exfoliated and toughened polypropylene‐blend‐montmorillonite (PP/MMT) nanocomposites were prepared by melt extrusion in a twin‐screw extruder. Special attention was paid to the enhancement of clay exfoliation and toughness properties of PP by the introduction of a rubber in the form of compatibilizer toughener: ethylene propylene diene‐based rubber grafted with maleic anhydride (EPDM‐g‐MA). RESULTS: The resultant nanocomposites were characterized using X‐ray diffraction, atomic force microscopy, scanning electron microscopy, thermogravimetric analysis, dynamic mechanical analysis and Izod impact testing methods. It was found that the desired exfoliated nanocomposite structure could be achieved for all compatibilizer to organoclay ratios as well as clay loadings. Moreover, a mechanism involving a decreased size of rubber domains surrounded with nanolayers as well as exfoliation of the nanolayers in the PP matrix was found to be responsible for a dramatic increase in impact resistance of the nanocomposites. CONCLUSION: Improved thermal and dynamic mechanical properties of the resultant nanocomposites promise to open the way for highly toughened super PPs via nanocomposite assemblies even with very low degrees of loading. Copyright © 2008 Society of Chemical Industry     

Effects of the ethylene–propylene–diene monomer microstructural parameters and interfacial compatibilizer upon the EPDM/montmorillonite nanocomposites microstructure: Rheology/permeability correlation

Attempts have been made to investigate the effects of ethylene–propylene–diene monomer (EPDM) rubber structural parameters on the developed microstructure, mechanical properties, rheology, and oxygen gas permeability of EPDM/organically modified montmorillonite (O‐MMT) nanocomposite samples prepared via melt mixing. Maleic anhydride grafted EPDM (EPDM‐g‐MAH) has been employed as an interfacial compatibilizer. The influence of the EPDM melt viscosity and chain linearity on the extent of exfoliation of the clay nanolayers has been evaluated through the calculation of the nanolayer aspect ratio (length/thickness) with the Halpin–Tsai model. The results are consistent with the X‐ray diffraction patterns of the samples. The flocculation of the clay nanolayers has been found to be more probable when O‐MMT is mixed with highly branched, low‐molecular‐weight EPDM. More exfoliation occurs when EPDM rubber with a high molecular weight but low branching is used. This has been confirmed by more nonlinear melt rheology behavior and broadening of the retardation time spectra. Maleated EPDM has been shown to be effective in enhancing the molecular intercalation of the clay nanolayers and the prevention of flocculation in both low‐molecular‐weight and high‐molecular‐weight EPDM matrices. Dynamic melt rheology measurements have revealed nonterminal behavior within the low‐frequency range by interfacially compatibilized molten samples with an EPDM‐g‐MAH/clay ratio of 3, regardless of the matrix molecular weight and chain linearity. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Effects of the compatibilizer structural parameters on microstructural formation in ethylene–propylene–diene monomer rubber/ethylene–propylene–diene monomer rubber‐g‐maleic anhydride/organoclay nanocomposites

Nanocomposite vulcanizates based on ethylene–propylene–diene monomer rubber (EPDM) and organically modified montmorillonite with improved mechanical and barrier properties were prepared via a melt‐mixing process in the presence of maleic anhydride grafted ethylene–propylene–diene monomer rubber (EPDM‐g‐MAH) as an interfacial compatibilizer. The effects of the EPDM Mooney viscosity as the matrix and also the compatibilizer molecular weight and its maleation degree on the developed microstructure were also studied. The annealing of the vulcanized nanocomposites based on a low‐Mooney‐viscosity EPDM matrix and low‐Mooney‐viscosity EPDM‐g‐MAH enhanced the flocculation of the dispersed clay platelets; this implied that the flocculated structure for the clay nanolayers was more thermodynamically preferred in these nanocomposites. This was verified by the decrease in the oxygen permeability of the nanocomposite vulcanizates with increasing annealing time. The tendency of the clay nanosilicate layers to flocculate within the matrix of EPDM was found to be influenced by the clay volume fraction, the maleation degree, and also, the Mooney viscosity of the compatibilizer. Interfacially compatibilized nanocomposites based on high‐molecular‐weight EPDM exhibited a more disordered dispersion of the clay nanolayers, with a broadened relaxation time spectra; this was attributed to the higher shearing subjected to the mix during the melt‐blending process. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

NR/SBR/organoclay nanocomposites: Effects of molecular interactions upon the clay microstructure and mechano‐dynamic properties

Nanocomposites based on (70/30) blends of natural rubber (NR), styrene‐butadiene rubber (SBR), and organoclay (OC) have been prepared successfully via melt‐mixing process. Effects of the extent of polymers/clay interactions upon the developed microstructure, fatigue life, and dynamic energy loss by the nanocomposites have been investigated. Maleated EPDM (EPDM‐g‐MAH) and epoxidized NR (ENR50) were employed as compatibilizer. Nanocomposites were characterized by means of X‐ray diffractometer (XRD), transmission electron microscope (TEM), scanning electron microscope, atomic force microscopy, root mean square, and dynamic mechanical thermal analysis. EPDM‐g‐MAH showed more potential in enhancing dispersion of the clay nanolayers and their interaction with rubber phases. More potential for separating and dispersing the clay nanoplatelets with better interface enhancement was exhibited by EPDM‐g‐MAH as compatibilizer. This was consistent with higher resistance towards large strain cyclic deformations along with more heat build‐up characteristics showed by EPDM‐g‐MAH based nanocomposites especially at compatibilizer/organoclay ratio of 3. Pronounced non‐terminal behavior within low frequency region was also observed for melt storage modulus of this nanocomposite, indicating higher extent of intercalation/exfoliation microstructure with reinforced interfaces than the nanocomposite generated by ENR50. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Microstructure‐properties correlations in dynamically vulcanized nanocomposite thermoplastic elastomers based on PP/EPDM

Thermoplastic vulcanized (TPV) nanocomposites were prepared in a laboratory mixer using EPDM, polypropylene of different viscosities, maleic anhydride modified polypropylene, an organo‐clay, and a sulfur‐based curing system. Based on the obtained results from X‐ray diffraction, transmission electron microscopy (TEM), scanning electron microscopy (SEM), differential scanning calorimeter, and mechanical properties, the microstructure of the prepared nanocomposites was found to be sensitive to the viscosity difference between the two phases and the clay content. X‐ray diffraction and TEM images of the TPV nanocomposites showed that clay was nearly exfoliated and randomly distributed into the polypropylene phase. The SEM photomicrographs of the dynamically vulcanized thermoplastic elastomer samples showed that the rubber particles were dispersed through the polypropylene in form of aggregates and their size increased with the introduction of clay. The nanoscale dimensions of the dispersed clay resulted in a significant improvement of the tensile modulus of the TPV nanocomposite samples, from 20 to 90% depending on clay content and the viscosity ratio of PP/EPDM. In the PP nanocomposites, the clay layers act as nucleating agents, resulting in higher crystallization temperature and reduced degree of crystallinity. Moreover, the oxygen permeability in the TPV nanocomposites was found to be lower than in unfilled but otherwise similar materials. POLYM. ENG. SCI., 47:207–217, 2007. © 2007 Society of Plastics Engineers.     

Peroxide vulcanized EPDM rubber/polyhedral oligomeric silsesquioxane nanocomposites: Vulcanization behavior,mechanical properties,and thermal stability

Effects of two different polyhedral oligomeric silsesquioxane (POSS), an acrylisobutyl POSS (AIBuPOSS) containing an acrylate group along with seven isobutyl group on its cage and an octaisobutyl POSS where the acrylate group is absent, on vulcanization behavior, mechanical properties, and thermal stability of peroxide vulcanized ethylene‐propylene‐diene rubber (EPDM) were investigated. The POSS was incorporated into the EPDM by melt mixing with POSS content of 0–10 part per hundred of rubber (phr). Oscillating disk rheometer analysis revealed that the acrylate group of the POSS are activated by dicumyl peroxide and improves the peroxide crosslinking efficiency of EPDM rubber. Solid state ²⁹Si‐nuclear magnetic resonance spectroscopy analysis and field emission scanning electron microscopy with energy dispersive X‐ray analysis of the EPDM/POSS vulcanizates showed that the AIBuPOSS are covalently grafted onto the EPDM chain during vulcanization and are dispersed uniformly at the nanometer scale in the rubber matrix. The EPDM/AIBuPOSS nanocomposites exhibit great improvement in tensile, tear strength, and modulus with a concurrent increase in elongation‐at‐break. Enhanced thermal stability in the nanocomposite was also observed. POLYM. ENG. SCI., 55:2814–2820, 2015. © 2015 Society of Plastics Engineers     

Process for preparing a nylon‐6/ clay/acrylate rubber nanocomposite with high toughness and stiffness

A novel nylon‐6/clay/acrylate rubber ternary nanocomposite has been prepared using a process developed by the authors. The process consists of two steps: firstly, an acrylate rubber/clay composite (ARCC) was manufactured by spray‐drying a mixture of clay slurry and irradiated acrylate rubber latex; secondly, the nylon‐6/unmodified clay/acrylate rubber ternary nanocomposite was prepared by blending ARCC and nylon‐6. It has been found that the acrylate rubber particles and clay platelets can help each other to disperse or exfoliate in the nylon‐6 matrix. The silicate layers without organic treatment are exfoliated with the aid of irradiated acrylate rubber particles and the irradiated acrylate rubber particles are uniformly dispersed in the matrix with the aid of clay platelets. The novel nanocomposite prepared using the new process shows simultaneously high impact strength, high flexural modulus and high heat distortion temperature. Copyright © 2007 Society of Chemical Industry     

Effects of mixing protocols on impact modified poly(lactic acid) layered silicate nanocomposites

Poly(lactic acid)/2 wt % organomodified montmorillonite (PLA/OMMT) was toughened by an ethylene‐methyl acrylate‐glycidyl methacrylate (E‐MA‐GMA) rubber. The ternary nanocomposites were prepared by melt compounding in a twin screw extruder using four different addition protocols of the components of the nanocomposite and varying the rubber content in the range of 5–20 wt %. It was found that both clay dispersion and morphology were influenced by the blending method as detected by X‐ray diffraction (XRD) and observed by TEM and scanning electron microscopy (SEM). The XRD results, which were also confirmed by TEM observations, demonstrated that the OMMT dispersed better in PLA than in E‐MA‐GMA. All formulations exhibited intercalated/partially exfoliated structure with the best clay dispersion achieved when the clay was first mixed with PLA before the rubber was added. According to SEM, the blends were immiscible and exhibited fine dispersion of the rubber in the PLA with differences in the mean particle sizes that depended on the addition order. Balanced stiffness‐toughness was observed at 10 wt % rubber content in the compounds without significant sacrifice of the strength. High impact toughness was attained when PLA was first mixed with the clay before the rubber was added, and the highest tensile toughness was obtained when PLA was first compounded with the rubber, and then clay was incorporated into the mixture. Thermal characterization by DSC confirmed the immiscibility of the blends, but in general, the thermal parameters and the degree of crystallinity of the PLA were not affected by the preparation procedure. Both the clay and the rubber decreased the crystallization temperature of the PLA by acting as nucleating agents. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41518.     

Thermoplastic elastomeric composition based on ground rubber tire

Ground rubber tire (GRT) is a particulate vulcanizate consisting mainly of rubber hydrocarbon and fillers. Rubber hydrocarbon of GRT (rGRT) has been used as a partial substitute for EPDM rubber in a dynamically vulcanized EPDM/acrylic‐modified HDPE (A‐HDPE) blend. The blends with higher rubber content show poor processability and physical properties, while the compositions with higher plastic content behave like toughened plastics. However, the 60:40 rubber/plastic blend was found to behave as a thermoplastic elastomer, and it was observed that 50% of EPDM can be replaced by rGRT without deterioration in properties.     

Preparation and properties of EPDM/organomontmorillonite hybrid nanocomposites

Hybrid nanocomposites based on organophillic montmorillonite (MMT) and ethylene–propylene–diene rubber (EPDM) have been prepared by a melt compounding process. From analysis by X‐ray diffraction and transmission electron microscopy, the rubber molecules were found to be intercalated into the galleries of organoMMT and the silicate layers of organoMMT are uniformly dispersed as platelets of 50–80 nm thickness in the EPDM matrix. Dynamic mechanical studies reveal a strong rubber–filler interaction in the hybrid nanocomposite which is manifested in the lowering of tan δ at the glass transition temperature. The hybrid nanocomposites exhibit great improvement in tensile and tear strength, and modulus, as well as elongation‐at‐break. Moreover, the permeability of oxygen for the hybrid nanocomposite was reduced remarkably. © 2002 Society of Chemical Industry     

The role of rubber characteristics in preparing rubber/clay nanocomposites by melt compounding

Rubber/organic clay (OC) nanocomposites were produced by melt blending. Polar or unsaturated matrices (e.g., NBR and SBR) could easily enter into OC layers, whereas using nonpolar unsaturated rubber (EPDM), without other additives' help, intercalation structure could not be directly obtained. For the EPDM system, an intercalated structure was observed in presence of stearic acid (SA) for composites composed of SA and OC. Transmission electron microscopy observation showed that the dispersion of clay in nonpolar saturated rubber matrix was much poorer than that in polar or unsaturated matrix. The same effect of polar matrix was confirmed by comparison between IIR/OC and BIIR/OC systems. Moreover, using OC pretreated by SA (S‐OC), the dispersion of clay was obviously improved in the investigated nanocomposites, due to the intercalation of SA into OC interlayers. Especially in the nonpolar saturated EPDM system, the intercalation structure could be easily observed. Relative to the corresponding nanocomposites using OC, tensile strengths and the stresses at low strain of NBR and SBR based nanocomposites with S‐OC were significantly improved; while with EPDM nanocomposite, using S‐OC, only tensile strengths were improved but the stresses at low strain were almost the same, which should be related to the different interfacial force between OC and different rubber matrices. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

The role of nanofillers on (natural rubber)/(ethylene vinyl acetate)/clay nanocomposite in blending and foaming

Nanocomposite foams were fabricated from 60/40 wt% ethylene vinyl acetate (EVA)/natural rubber (NR) blends by using azodicarbonamide as a blowing agent. Two different nanofillers (sodium montmorillonite and organoclay) were employed to study their effects on foam properties. The results were also compared with conventional (china clay)‐filled foams. Transmission electron microscopy, X‐ray diffraction, scanning electron microscopy, and three‐dimensional Microfocus X‐ray computed tomography scanning analysis were performed to characterize the EVA/NR blend morphology and foam structures. The results revealed that the nanofiller acted as a blend compatibilizer. Sodium montmorillonite was more effective in compatibilization, generating better phase‐separated EVA/NR blend morphology and improving foam structure. Higher filler loading increased the specific tensile strength of rubber foams. The rubber nanocomposite foam showed superior specific tensile strength to the conventional rubber composite foam. The elastic recovery and compressive strength of the nanocomposite foams decreased with increasing filler content, whereas the opposite trend was observed for the conventional composite foams with china clay. The thermal conductivity measurement indicated that the nanofiller had better beneficial effect on thermal insulation over china clay filler. From the present study, the nanofillers played an important role in obtaining better blend morphology as compatibilizer, rather than the nucleating agent and the nanofiller content of 5 phr (parts by weight per hundred parts of rubber) was recommended for the production of EVA/NR nanocomposite foams. J. VINYL ADDIT. TECHNOL., 21:134–146, 2015. © 2014 Society of Plastics Engineers     

Characteristics of ethylene propylene diene monomer rubber/organoclay nanocomposites resulting from different processing conditions and formulations

Several parameters which affect the nanocomposite formation in a sulfur‐cured ethylene propylene diene rubber (EPDM) containing 10 phr organoclay (montmorillonite modified with octadecylamine; MMT–ODA), were investigated. The parameters varied were linked to processing (mixer type, temperature) and rubber recipe (compatibilizer, accelerator). Increasing temperature and high shear mixing (internal mixer instead of open mill) improved the mechanical performance of the rubber nanocomposites. A more pronounced effect was achieved by using polar EPDM rubbers (maleic anhydride and glycidyl methacrylate grafted version) as compatibilizer. Among the accelerators, zinc diethyldithiocarbamate proved to be most suitable. The microstructure of the rubber/organoclay systems was studied by X‐ray diffraction, transmission electron microscopy and scanning electron microscopy. Organoclay intercalation/exfoliation was accompanied by its more or less severe confinement (reaggregation, deintercalation). This was traced to a partial or full removal of the ODA intercalant from the clay galleries via the formation of a zinc complex in which amine groups of the ODA and sulfur participated. Copyright © 2004 Society of Chemical Industry     

The influence of matrix viscosity and composition on the morphology,rheology, and mechanical properties of thermoplastic elastomer nanocomposites based on EPDM/PP

The morphological and rheological properties of thermoplastic elastomer nanocomposites (TPE nanocomposites) were studied using different viscosities of polypropylene (PP) and ethylene‐propylene‐diene monomer (EPDM) rubber content (20, 40, 60 wt%). The components, namely EPDM, PP, Cloisite 15A, and maleic anhydride‐modified PP as compatibilizer, were compounded by a one‐step melt mixing process in a laboratory internal mixer. The structure of the nanocomposites was characterized with X‐ray diffraction, scanning electron microscopy, transmission electron microscopy, and rheometry in small amplitude oscillatory shear. The distribution state of the clay between the two phases (PP and EPDM) was found to be dependent on the viscosity ratio of PP to EPDM. In the nanocomposites prepared based on low viscosity PP (LVP) and EPDM, the clay was mostly dispersed into the PP phase and the size of the dispersed rubber particles decreased in comparison with unfilled but otherwise similar blends. However, the dispersed elastomer droplet size in the high viscosity PP (HVP) blends containing 40 and 60% EPDM increased with the introduction of the clay. For TPE nanocomposites, the dependence of the storage modulus (G′) on angular frequency (ω) followed a clear nonterminal behavior. The increase in the storage modulus and the decrease in the terminal zone slope of the elastic modulus curve were found to be larger in the LVP nanocomposite in comparison with the HVP sample. The yield stress of nanoclay‐filled blends prepared with LVP increased more than that of HVP samples. The tensile modulus improved for all nanocomposites but a higher percentage of increase was observed in the case of LVP samples. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Radiation‐processed polychloroprene‐co‐ethylene–propene diene terpolymer blends: Evaluation of blend morphology,miscibility, and physical properties

The miscibility of polychloroprene rubber (CR) and ethylene–propylene–diene terpolymer rubber (EPDM) was studied over the entire composition range. Different blend compositions of CR and EPDM were prepared by initially mixing on a two‐roll mill and subsequently irradiating to different gamma radiation doses. The blends were characterized by differential scanning calorimetry, Fourier transform infrared spectroscopy, density measurement, hardness measurement, and solvent permeability analysis. The compatibility of the blends was studied by measuring the glass transition temperature and heat capacity change of the blends. The immiscibility of blends was reflected by the presence of two glass transition temperatures; however, partial miscible domains were observed due to inter diffusion of phases. Permeation data fitted best with the Maxwell's model and indicated that in CR‐EPDM blends, EPDM exists as continuous phase with CR as dispersed phase for lower CR weight fractions and phase inversion occurred in 40–60% CR region. It was observed that CR improved oil resistance of EPDM; however, the effect was prominent for blends of >20% CR content. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Nanocomposites of poly(trimethylene terephthalate) with organoclay

Two different kinds of clay were organomodified with cetylpyridinium chloride (CPC) as an intercalation agent. Poly(trimethylene terephthalate) (PTT)/organoclay nanocomposites were prepared by the solution intercalation method. Wide‐angle X‐ray diffraction (WAXD) indicated that the layers of clay were intercalated by CPC and the interlayer spacing was a function of the cationic exchange capacity (CEC) of the clay: the higher the CEC, the larger the interlayer spacing is. The WAXD studies showed that the interlayer spacing of organoclay in the nanocomposites depends on the amount of organoclay. From the results of differential scanning calorimetry analysis it was found that clay behaves as a nucleating agent and enhances the crystallization rate of PTT. The maximum enhancement of the crystallization rate for the nanocomposites was observed in nanocomposites containing about 5 wt % organoclay with a range of 1–15 wt %. The thermal stability of the nanocomposites was enhanced by the addition of 1–10 wt % organoclay as found from thermogravimetric analysis. The thermal stability of the PTT/organoclay nanocomposites was related to the organoclay content and the dispersion in the PTT matrix. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3315–3322, 2003     

Preparation and relaxation dynamics of ethylene–propylene–diene rubber/clay nanocomposites with crosslinking interfacial design

Ethylene–propylene–diene rubber (EPDM)/clay nanocomposites with crosslinking bonding at the interface were fabricated through the intercalation method involving double‐bond functional groups. For comparison, an organoclay modified with an intercalation agent without double bonds was also prepared. X‐ray diffraction indicated that the EPDM intercalated into the galleries of the nanoclay due to crosslinking with the organic intercalation reagent containing double bonds. According to the dielectric relaxation spectra, the segmental relaxation of EPDM was greatly confined, due to the strong filler/polymer interfacial interaction. And a new relaxation appeared at higher temperature and lower frequency than segmental relaxation when the content of clay with double bonds reached 10 phr; the new relaxation is attributed to interfacial relaxation. Whereas the new relaxation did not appear by adding ordinary organoclay, the dynamic mechanical analysis loss peak of EPDM, corresponding to the glass transition, moved to a higher temperature due to covulcanization. The presence of crosslinking in the EPDM/clay nanocomposites can play a significant role in improving their mechanical properties. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45553.     

Flame retardancy and char microstructure of nylon‐6/layered silicate nanocomposites

We investigated the effect of organically modified clay alone and in combination with zinc borate on the thermal/flammability behavior of nylon‐6 nanocomposites. Differential thermogravimetric analysis indicated that the peak decomposition temperature was not affected by the addition of clay, but the rate of weight loss decreased with increase in clay concentration. Nanocomposite films of approximately 0.5 mm thickness with 2.5 and 5 wt % clay burned for almost the same duration as neat nylon‐6 but with reduced dripping in horizontal flame test. The 10 wt % clay nanocomposite sample burned without any dripping and the flame spread rate was reduced by 25–30%. Zinc borate/clay containing nanocomposite developed into a very good intumescent system in cone calorimeter test, swelling about 10–13 mm height prior to ignition forming a cellular char structure. This was found to be an effective composition in reducing the heat release and mass loss rate of nylon‐6 by about 65% and at par with 10 wt % clay nanocomposite. Flame retardant behavior could be attributed to distinct char morphologies observed through scanning electron microscopy. Fourier transform infrared spectroscopy of the 10 wt % clay nanocomposite char showed the presence of amides, indicating possible residual polymer within the shielded char. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1540–1550, 2007     

Effect of zinc oxide nanoparticles as cure activator on the properties of natural rubber and nitrile rubber

Zinc oxide (ZnO) nanoparticles were synthesized by homogeneous precipitation and calcination method and were then characterized by transmission electron microscopy and X‐ray diffraction analysis. Synthesized ZnO was found to have no impurity and had a dimension ranging from 30–70 nm with an average of 50 nm. The effect of these ZnO nanoparticles as cure activator was studied for the first time in natural rubber (NR) and nitrile rubber (NBR) and compared with conventional rubber grade ZnO with special reference to mechanical and dynamic mechanical properties. From the rheograph, the maximum torque value was found to increase for both NR and NBR compounds containing ZnO nanoparticles. ZnO nanoparticles were found to be more uniformly dispersed in the rubber matrix in comparison with the conventional rubber grade ZnO as evident from scanning electron microscopy/X‐ray dot mapping analysis. The tensile strength was observed to improve by 80% for NR when ZnO nanoparticles were used as cure activator instead of conventional rubber grade ZnO. An improvement of 70% was observed in the case of NBR. The glass transition temperature (T_g) showed a positive shift by 6°C for both NR and NBR nanocomposites, which indicated an increase in crosslinking density. The swelling ratio was found to decrease in the case of both NR and NBR, and volume fraction of rubber in swollen gel was observed to increase, which supported the improvement in mechanical and dynamic mechanical properties. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Study on the milling behavior of chloroprene rubber blends with ethylene–propylene–diene monomer rubber,polybutadiene rubber,and natural rubber

The viscoelastic properties of the blends of chloroprene rubber (CR) with ethylene–propylene–diene monomer rubber (EPDM), polybutadiene rubber (BR), and natural rubber (NR) at different temperature were studied using rubber processing analyzer (RPA). Mooney viscosities of compounds were measured and tight milling and sheeting appearance were observed on a two‐roll mill. The results showed that Mooney viscosities and the elastic modulus of the blends decreased with the increase of the temperature from 60 to 100°C. And the decreasing trends of pure CR, pure NR, and CR/NR blend compounds were more prominent than that of pure EPDM, pure BR, CR/EPDM, and CR/BR blend compounds. For CR/EPDM blend compounds, the decreasing trend became slower with the increase of EPDM ratio in the blend. Compared with pure CR, pure NR and CR/NR blend compounds, pure EPDM, pure BR compounds, and the blend compounds of CR/EPDM and CR/BR showed less sensibility to temperature and they were less sticky to the metal surface of rolls and could be kept in elastic state at higher temperature, easy to be milled up and sheeted. At the same blend ratio and temperature, the property of tight milling of the blends decreased in the sequence of CR/EPDM, CR/BR, and CR/NR. With the increase of EPDM, BR, or NR ratio in CR blends, its property of tight milling was improved. POLYM. COMPOS., 28:667–673, 2007. © 2007 Society of Plastics Engineers