Rheological and mechanical properties of PEO/block copolymer blends

Small quantities of block copolymers from two families, styrene‐butadiene‐methylmethacrylate (SBM) and methylmethacrylate‐butylacrylate‐methylmethacrylate (MAM) have been added to a polyethylene oxide (PEO) in order to improve its processability, namely increasing its elastic modulus without increasing too much its shear viscosity. The copolymers contain one block of polymethylmethacrylate (PMMA) that is compatible with PEO; the other blocks create nano phases, dispersed in the PEO matrix. Considerable efforts were devoted to finding the best blending method, either melt processing or solution casting. PEO is very sensitive to shear, and was found to degrade both in the bulk and in solution. Degradation, which cannot be avoided, was quantified through intrinsic viscosity measurements. The rheological characterization of blends containing 1, 2, and 5 wt% block copolymer was carried out. The elastic modulus was found to increase more than the complex viscosity. Blends obtained by solution casting technique gave better results. The elongational viscosity obtained for one blend containing 5 wt% of SBM showed a slight increase with respect to the pure PEO. Mechanical properties were then investigated, through tensile tests and dynamic mechanical analysis in flexion and in torsion; the copolymer generally enhanced the mechanical properties. POLYM. ENG. SCI., 45:1385–1394, 2005. © 2005 Society of Plastics Engineers     

Rheological,mechanical, thermal,and morphological properties of polypropylene/ethylene‐octene copolymer blends

Rheological and morphological studies were performed on polymer blends of ethylene‐octene copolymer [polyethylene elastomer (PEE)] and polypropylene (PP). The viscosities of PEE, PP, and PEE/PP blends were analyzed using an Instron capillary rheometer and a Rheometrics Dynamic Stress Rheometer, SR 200. A non‐Newtonian flow behavior was observed in all samples in the shear rate range from 27 to 2700 s⁻¹, whereas at shear rates in the range from 0.01 to 0.04 s⁻¹, a Newtonian flow behavior was verified. The scanning electron micrographs showed that dual‐phase continuity may occur between 50 and 60 (wt %) of PEE. This result is consistent with the Sperling's model. The mechanical analysis showed that PEE/PP, with 5 wt % of PEE, presented an increase on the mechanical properties and as the PEE content increased, a negative deviation in relation to an empirical equation was observed. Thermal analysis showed that there were no change in the crystallization behavior of the matrix when different elastomer contents were added. Dynamic mechanical thermal analysis showed that samples with low PEE contents presented only one peak, indicating a certain degree of miscibility between the components of these blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 692–704, 2000     

Study of grafting propylene–ethylene block copolymer

The article describes the mechanical properties of a propylene–ethylene block copolymer (Co-PP) used as a matrix with acrylic acid (AA) and strengthened with glass fiber. Isotactic polypropylene (i-PP) is also used as a matrix to compare with the results obtained from the Co-PP grafting. Experimental results indicate that AA grafting improves the interfacial adhesion between the matrices and glass fiber. AA grafting also enhances the mechanical properties of glass fiber-reinforced polypropylene (FRPP). A quantitative titration is performed to analyze the grafting ratio and grafting efficiency. In addition, the specimens are injection-molded to investigate the mechanical properties and morphologies. In addition, the effects on the matrix structure, attributed to the grafting and blending of the glass fiber, are also investigated. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 68: 977–988, 1998     

Mechanical properties and morphology of crosslinked PP/PE blends and PP/PE/propylene–ethylene copolymer blends

Blending is an effective method for improving polymer properties. However, the problem of phase separation often occurs due to incompatibility of homopolymers, which deteriorates the physical properties of polyblends. In this study, isotactic polypropylene was blended with low-density polyethylene. Crosslinking agent and copolymers of propylene and ethylene (either random copolymer or block copolymer) were added to improve the interfacial adhesion of PP/LDPE blends. The tensile strength, heat deflection temperature, and impact strength of these modified PP/PE blends were investigated. The microstructures of polyblends have been studied to interpret the mechanical behavior through dynamic viscoelasticity, wide-angle X-ray diffraction, differential scanning calorimetry, picnometry, and scanning electron microscopy. The properties of crosslinked PP/PE blends were determined by the content of crosslinking agent and processing method. For the material blended by roll, a 2% concentration of peroxide corresponded to a maximum tensile strength and minimum impact strength. However, the mechanical strength of those products blended by extrusion monotonously decreased with increasing peroxide content because of serious degradation. The interfacial adhesion of PP/PE blends could be enhanced by adding random or block copolymer of propylene and ethylene, and the impact strength as well as ductility were greatly improved. Experimental data showed that the impact strength of PP/LDPE/random copolymer ternary blend could reach as high as 33.3 kg · cm/cm; however, its rigidity and tensile strength were inferior to those of PP/LDPE/block copolymer blend.     

Microdeformation mechanisms in propylene–ethylene block copolymer

Blends of propylene–ethylene block copolymer (PEB) and propylene homopolymer (PP) were prepared to give various rubber contents (4–20 wt %). By diluting the PEB with PP with molecular weight equal to that of the PEB matrix, molecular characteristics of all the blends were kept constant. The rubber particle size and size distribution of all the blends were almost constant, so that the interparticle distance decreased with increased rubber content. According to the observation of the fracture behavior at ?20°C, a brittle to ductile transition was found at the rubber content of 16 wt %. Microdeformation behavior of the blends was investigated in the region of brittle to ductile transition by using transmission electron microscopy. In the case of the brittle sample with low rubber content, crazing and voiding were observed. Whereas even in the ductile sample with high rubber content, crazing certainly took place before shear yielding. The origin of ductile fracture could possibly be attributed to the relaxation of strain constraint by the microvoids contained in the craze. © 1993 John Wiley & Sons, Inc.     

Melt rheology and properties of compatibilized recycled poly(ethylene terephthalate)/(styrene‐ethylene‐ethylene‐propylene‐styrene) block copolymer blends

Blends of recycled poly(ethylene terephthalate) (R‐PET) and (styrene‐ethylene‐ethylene‐propylene‐styrene) block copolymer (SEEPS) compatibilized with (maleic anhydride)‐grafted‐styrene‐ethylene‐butylene‐styrene (SEBS‐g‐MAH) were prepared by melt blending. The compatibilizing effects of SEBS‐g‐MAH were investigated systematically by study of the morphology, linear viscoelastic behavior, and thermal and mechanical properties of the blends. The results show that there is good agreement between the results obtained by rheological measurement and morphological analysis. The rheological test shows that the melt elasticity and melt strength of the blends increase with the addition of SEBS‐g‐MAH. The Cole‐Cole plots and van Gurp‐Palmen plots confirm the compatibilizing effect of SEBS‐g‐MAH. However, the Palierne model fails to predict the linear viscoelastic properties of the blends. The morphology observation shows that all blends exhibit a droplet‐matrix morphology. In addition, the SEEPS particle size in the (R‐PET)/SEEPS blends is significantly decreased and dispersed uniformly by the addition of SEBS‐g‐MAH. Differential scanning calorimeter analysis shows that the crystallization behavior of R‐PET is restricted by the incorporation of SEEPS, whereas the addition of SEBS‐g‐MAH improves the crystallization behavior of R‐PET compared with that of uncompatibilized (R‐PET)/SEEPS blends. The Charpy impact strength of the blends shows the highest value at SEBS‐g‐MAH content of 10%, which is about 210% higher than that of pure R‐PET. J. VINYL ADDIT. TECHNOL., 22:342–349, 2016. © 2014 Society of Plastics Engineers     

Effects of epoxy resin‐modified zinc‐ion‐coated nanosilica on structural,thermal and dynamic mechanical properties of propylene‐ethylene copolymer

This paper reports a comparative study of propylene–ethylene copolymer (EP) nanocomposites synthesized using zinc‐ion (Zn²⁺)‐coated nanosilica (ZNS) and the diglycidyl ether of bisphenol‐A (DGEBA, an epoxy resin)‐modified zinc‐ion‐coated nanosilica (EZNS) as nanofillers. These nanocomposites were prepared using the ‘melt mixing’ method at a constant loading level of 2.5 wt%. This loading level is much lower than that used for fillers in conventional composites. The EP nanocomposites were characterized using wide‐angle X‐ray diffractometer (WAXD), a thermo gravimetric analyzer (TGA), a differential scanning calorimeter (DSC), a dynamic mechanical analyzer (DMA) and scanning electron microscopy (SEM). DMA results showed a higher storage modulus for EP‐epoxy‐modified Zn²⁺‐coated nanosilica nanocomposite (EP‐EZNS) with respect to EP and EP‐Zn²⁺‐coated nanosilica nanocomposite (EP‐ZNS). In addition, TGA thermograms showed an increase in degradation temperature of EP in the presence of EZNS. Copyright © 2006 Society of Chemical Industry     

Rheological and mechanical properties of compatibilized polystyrene/ethylene vinyl acetate blends

In this study, a blend of polystyrene (PS)/ethylene vinyl acetate (EVA) (PS/EVA, 90 : 10 wt %) was compatibilized with three different block copolymers, in which their end blocks were compatible with either styrene or EVA. The compatibilized blends with different compositions were prepared using a twin‐screw extruder and injection molded into the required test specimens. Mechanical properties of the blends, such as tensile properties and Charpy impact strength, morphology of tensile fractured surfaces, rheological properties, and thermal properties, were investigated. The results show that the interaction between the dispersed and continuous phase can be improved by the addition of a compatibilizer. Appreciable improvement in the impact strength of the blend with 15 wt % of compatibilizer C (polystyrene‐block‐polybutadiene) was observed. Its mechanical properties are comparable to those of the commercial high‐impact polystyrene, STYRON 470. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2071–2082, 2004     

Thermal,thermo‐mechanical,and dynamic mechanical properties of polypropylene/cycloolefin copolymer blends

Interaction of the components and physical properties of the polypropylene (PP)/cycloolefin copolymer (COC) blends were studied by means of differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), Vicat softening temperature (VST), and measurements of the coefficient of linear thermal expansion (CLTE) and of the density. The attention was focused on the blends with 90–60% of PP by wt, where the COC minority component was present in the form of short fibers. DSC, DMTA, and density measurements concurrently prove the immiscibility of PP and COC. DSC measurements reveal that crystallinity and melting temperature of the PP component slightly decrease with the fraction of COC in blends, in the range of 56–47% and 164–161°C, respectively. Storage modulus and loss modulus of the blends are in a good accord with the model predictions based on (i) the equivalent box model (EBM) and on (ii) modified equations of the percolation theory. The dependence of the VST on the blend composition is in a good correlation with the previous morphological analysis. Measurements of the coefficient of thermal expansion provide useful data as the functions of temperature and blend composition. Density of the blends was found to obey the volume additivity. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Rheological properties and morphological evolutions of polypropylene/ethylene‐butene copolymer blends

This work aims at studying the extensional rheological behavior of polypropylene (PP), ethylene‐butene copolymer (PEB) and their blends in the melt. The weight fraction of the PEB in the blend is 20 and 40%, respectively. Dynamic mechanical analysis shows that these two blends exhibit two tanδ peaks corresponding to the glass transitions of the PP and PEB, respectively. Differential scanning calorimeter results indicate that the presence of the PEB does not alter the melting and crystallization temperatures of the PP. Master curves at 170°C are constructed for the storage and loss modulus as well as complex viscosity. The extensional behavior of the PP, PEB, and their two blends is studied. The PEB enhances the strain hardening of the PP. Changes in the blend morphology during the extensional analysis are also studied. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

LLDPE/LDPE blends. I. Rheological,thermal, and mechanical properties

Structure and mechanical properties were studied for the binary blends of a linear low density polyethylene (LLDPE) (ethylene‐1‐hexene copolymer; density = 900 kg m⁻³) with narrow short chain branching distribution and a low density polyethylene (LDPE) which is characterized by the long chain branches. It was found by the rheological measurements that the LLDPE and the LDPE are miscible in the molten state. The steady‐state rheological properties of the blends can be predicted using oscillatory shear moduli. Furthermore, the crystallization temperature of LDPE is higher than that of the LLDPE and is found to act as a nucleating agent for the crystallization of the LLDPE. Consequently, the melting temperature, degree of crystallinity, and hardness of the blend increase rapidly with increases in the LDPE content in the blend, even though the amount of the LDPE in the blend is small. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 3153–3159, 1999     

Rheology, phase morphology, mechanical, impact and thermal properties of polypropylene/metallocene catalysed ethylene 1-octene copolymer blends

Blends of a polypropylene (PP) and a metallocene catalysed ethylene-octene copolymer (EOC) were prepared using a single screw extruder fitted with a barrier screw design. The EOC used had 25 wt% 1-octene content and the weight fraction of EOC in the blends covered the range 1-30 wt.% Viscosity values for the blends determined experimentally from dual capillary rheological studies were similar to those calculated theoretically using the log additivity principle described by Ferry. This result together with scanning electron microscopy (SEM) observations and evidence from tan δ curves from dynamic mechanical thermal analysis showed PP and EOC to be partially miscible for blends having 10 wt% EOC or less. The tensile modulus, break strength and flexural modulus of the blends decreased with respect to virgin PP as the weight fraction of EOC was increased to 30 wt.% The diminution in mechanical properties was concomitant with an initial increase in elongation at break from 40% for neat PP to 140% for the blend with 15 wt% EOC before decreasing to 65% when 30 wt% EOC was blended. The optimum impact modification of the PP used in this study, in the temperature range −40 to 23 °C, was achieved by blending with between 20 and 30 wt% EOC.     

Crystallinity and mechanical properties of polylactide/ether‐amide copolymer blends

The present study focuses on the improvement of impact properties and particularly on the interaction between crystallinity development and mechanical properties of impact modified polylactide (PLA). The PLA was toughened by the addition of a random linear ether‐amide copolymer (PEBAX 3533?). A random copolymer of ethylene, methyl‐acrylate, and glycidyl‐methacrylate (LOTADER AX8900?) was also used to reactively compatibilize the ether‐amide copolymer with the PLA matrix. Melt rheology of the blends was investigated in small amplitude oscillatory shear and showed that the impact modifier could significantly influence the viscoelastic response of the material. The Izod impact resistance and tensile properties were measured using standard testing protocols. The blend morphology was also examined using scanning electron microscopy on cryofractured and microtomed surfaces, while the crystalline morphology was assessed by optical microscopy. A sub‐micron dispersion of the impact modifier was achieved in the presence of the reactive compatibilizer. Significantly improved impact strength was found with 10 wt % impact modifier. High crystallinity samples showed the highest impact strength with values reaching 68 kJ/m², hence a 20‐fold improvement with respect to the neat PLA. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44677.     

Rheological and thermal properties of single‐site polyethylene blends

Branched polyethylenes, low‐density polyethylenes (LDPE1 and LDPE2) or long‐chain‐branched very low density polyethylenes (VLDPE2), were blended with very low density polyethylenes containing short branches (VLDPE1 and VLDPE3). The rheological and thermal measurements of the pure copolymers and their blends (VLDPE1–LDPE1, VLDPE1–LDPE2, VLDPE1–VLDPE2, and VLDPE2–VLDPE3) were taken by controlled stress rheometry and differential scanning calorimetry, respectively. The shear‐thinning effect became stronger with increasing long‐chain‐branched polymer compositions when it was correlated with the flow behavior index, and the extent of shear thinning was different for each blend set. Stronger shear thinning and a linear composition dependence of the zero‐shear viscosity were observed for the VLDPE1–LDPE1 and VLDPE1–LDPE2 blends. These blends followed the log additivity rule, and this indicated that they were miscible in the melt at all compositions. In contrast, a deviation from the log additivity rule was observed for the VLDPE1–VLDPE2 blend compositions with 50% or less VLDPE2 and for the VLDPE3–VLDPE2 blends with 50% or more VLDPE2. The thermal properties of the blends were consistent with the rheological properties. VLDPE1–LDPE1 and VLDPE1–LDPE2 showed that these blends were characteristic of a single‐component system at all compositions, whereas the phase separation (immiscibility) was detected only for VLDPE1–VLDPE2 blends with 50% or less VLDPE2 and for VLDPE3–VLDPE2 blends with 50% or more VLDPE2. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1549–1557, 2005     

Compatibility study of chlorinated polyethylene/ethylene methacrylate copolymer blends using thermal,mechanical, and chemical analysis

Blends of chlorinated polyethylene (CPE) elastomer and ethylene methacrylate copolymer (EMA) in various compositions were studied for their compatibility using differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and Fourier transform infrared (FTIR) spectroscopy techniques. Irrespective of measurement techniques used, all blends showed a single glass transition temperature (T_g) lying in between the T_g of control polymers in both DSC and DMA. Glass transition temperatures of blends obtained from DSC were in consistency with Couchman–Karasz equation. Also, the T_g obtained from both DSC and DMA are above the “rule of mixing” line of the two control polymers. These results from thermal analysis clearly indicate some compatibility between the two polymers. Furthermore, compatibility of CPE/EMA blends were also been investigated by FTIR spectroscopy and scanning electron microscopic analysis. A shifting of characteristic C? Cl stretching peak of CPE and C?O stretching peak of EMA toward lower wave number indicate the presence of specific interaction between the two polymers. Mechanical properties like tensile strength, modulus at 100% elongation, elongation at break, and hardness were observed above the line of additivity drawn between the two control polymers, which corroborate compatibility between CPE and EMA. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40316.     

Rice husk/poly(propylene‐co‐ethylene) composites: Effect of different coupling agents on mechanical,thermal, and morphological properties

Poly(propylene‐co‐ethylene) composites with rice husk were prepared in a corotating intermeshing twin‐screw extruder using four different coupling agents. While modified maleic anhydrides such as maleated polypropylene (MAPP) and maleated polyethylene (MAPE) are commonly used as compatibilizers to improve interfacial adhesion between lignocellulosic filler and matrix, in this study, polypropylene grafted with acid comonomer (CAPP) and high‐density polyethylene grafted with acid comonomer (CAPE) were also used. The morphologies and the thermal and mechanical properties of the composites were characterized using scanning electron microscopy, thermogravimetric analysis, differential scanning analysis, tensile and impact tests. The results indicate that the base resin of the compatibilizer is an important factor in determining the effectiveness of compatibilizers for composites. Composites with PP‐based compatibilizers are more effective than PE‐based compatibilizers due to the improved wetting of the former compatibilizer in the matrix polymer. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Morphology,crystallization, and thermal behavior of isotactic polypropylene/propylene‐g‐styrene blends

Optical microscopy, differential scanning calorimetry, and small angle X‐ray scattering techniques were used to study the influence of the crystallization conditions on morphology and thermal behavior of samples of binary blends constituted of isotactic polypropylene (iPP) and a novel graft copolymer of unsaturated propylene with styrene (uPP‐g‐PS) isothermally crystallized from melt, at relatively low undercooling, in a range of crystallization temperatures of the iPP phase. It was shown that, irrespective of composition, no fall in the crystallinity index of the iPP phase was observed. Notwithstanding, spherulitic texture and thermal behavior of the iPP phase in the iPP/uPP‐g‐PS materials were strongly modified by the presence of copolymer. Surprisingly, iPP spherulites crystallized from the blends showed size and regularity higher than that exhibited by plain iPP spherulites. Moreover, the amount of amorphous material located in the interspherulitic amorphous regions decreased with increasing crystallization temperature, and for a given crystallization temperature, with increasing uPP‐g‐PS content. Also, relevant thermodynamic parameters, related to the crystallization process of the iPP phase from iPP/uPP‐g‐PS melts, were found, composition dependent. The equilibrium melting temperature and the surface free energy of folding of the iPP lamellar crystals grown in the presence of uPP‐g‐PS content up to 5% (wt/wt) were, in fact, respectively slightly lower and higher than that found for the lamellar crystals of plain iPP. By further increase of the copolymer content, both the equilibrium melting temperature and surface free energy of folding values were, on the contrary, depressed dramatically. The obtained results were accounted for by assuming that the iPP crystallization process from iPP/uPP‐g‐PS melts could occur through molecular fractionation inducing a combination of morphological and thermodynamic effects. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 79: 2286–2298, 2001     

Rheological properties,oil, and thermal resistance in sulfur‐cured CPE/NR blends

The use of natural rubber (NR) for partly substituting elastomeric chlorinated polyethylene (CPE) was carried out. Sulfur curing was used to vulcanize NR phase in the blends. Mechanical, rheological, and thermal aging properties as well as oil resistance of the blends were investigated. The amount of NR in blends significantly affects properties of the blends. With NR content in blends up to 20 wt %, tensile properties are similar to those of the pure CPE, even after either oil immersion or thermal aging. Rheological properties of CPE/NR blends determined from the rubber process analyzer (RPA 2000) and parallel‐plate rheometer are controlled strongly by the blend composition. The viscoelastic behavior of pure CPE and the blends with CPE as a major component is governed by the viscous response, which could be seen from the high damping factor, particularly at high strain, the short linear viscoelastic range, and the high degree of pseudoplasticity. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1129–1135, 2004     

Processing behavior of polycarbonate/functionalized‐ethylene copolymer blends

The melt blending of polycarbonate (PC) and ethylene‐methacrylic acid copolymers (EFC) either in the acid form (EFC‐H) or partially neutralized with sodium (EFC‐Na) or zinc (EFC‐Zn) was investigated. Torque monitoring of the blending showed that the polymers are capable of reacting generating new chemical species that increase the melt viscosity. As general behavior, the torque curves pass by a maximum that takes place before 30 min, the final torque being higher than that of the individual polymers. SEC analyses reveal that PC degradation also occurs and is stronger in the case of blends with EFC‐Na that acts to catalyze PC degradation, promoting CO₂ formation. FTIR studies on chloroform insoluble fractions of the PC/EFC‐Zn blends showed that in addition to a very small number of carbonate groups, feature absorption bands of aromatic ester and hydroxyl groups appear in the new chemical species formed during the reactive processing.     

Rheological and mechanical properties of ternary blends of linear-low-density polyethylene/polypropylene/ethylene-propylene block polymers

The effect of addition of an ethylene-propylene block polymer on rheological and mechanical properties of a linear-low-density polyethylene/polypropylene blend was examined. The samples were prepared by melt blending in a twin-screw extruder followed by injection molding. The single-, two- and three-component systems were treated the same way. The mechanical behavior of the blends was evaluated by means of tensile, and flexural, tests at 23 and ?40°C. The capillary, elongational, and dynamic-flow measurements were performed at 190°C.