Grafting of N,N′‐methylenebisacrylamide onto cellulose using Co(III)‐acetylacetonate complex in aqueous medium

The grafting of N,N′‐methylenebisacrylamide (N,N′‐MBA) onto cellulose is carried out using the cobaltacetylacetonate complex (Co(acac)₃) under nitrogen atmosphere at 40°C. The rate of graft copolymerization has been studied as a function of [N,N′‐MBA], [Co(acac)₃], and temperature. The activation energy of grafting is found to be 156.0 k J mol⁻¹ within the temperature range of 30–60°C. The effect of perchloric acid, methanol, and surfactants on graft yield has also been studied and results are suitably explained. The higher efficiency of the metal chelate in initiation of graft copolymerization has been assumed due to the coordination of the π electrons of the N,N′‐MBA with the metal chelate, which facilitated the formation of the radicals through homolytic cleavage of metal–oxygen bond of the cobalt acetylacetonate complex. On the basis of the results, a suitable kinetic scheme for graft copolymerization is presented and rate expression is derived. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 906–912, 2000     

Synthesis,characterization and properties evaluation of copolymers of 2,3,4,5,6‐pentafluorostyrene and N‐phenylmaleimide

Copolymers of 2,3,4,5,6‐pentafluorostyrene (PFS) having a combination of high hydrophobicity and high glass transition temperature (T_g) are reported here for the first time. The copolymerization was carried out using N‐phenylmaleimide (NPM) as the comonomer and azobisisobutyronitrile (AIBN) as the initiator under both conventional thermal heating and microwave heating. The initial copolymerization rate was found to be higher under microwave heating than under thermal heating. The copolymerization parameters were determined using the Fineman–Ross method and were found to be r₁ (NPM) = 0.28 and r₂ (PFS) = 0.86. Increased incorporation of NPM in the copolymers led to an increase in T_g of the copolymers without significantly affecting the hydrophobicity of poly(2,3,4,5,6‐pentafluorostyrene). Thermal stability of the copolymers is also reported. Copyright © 2005 Society of Chemical Industry     

Synthesis of poly(β‐pinene)‐g‐polystyrene from allylic brominated poly(β‐pinene)

Poly(β‐pinene) was brominated by N‐bromosuccinimide on the allylic carbons. Then the brominated product was activated by AlEt₂Cl to initiate the polymerization of styrene to give a β‐pinene/styrene graft copolymer. AlEt₂Cl was selected because it alone could not initiate the polymerization of styrene. The obtained graft copolymer was characterized by GPC, ¹H‐NMR, and DSC measurements, respectively. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 599–603, 2000     

Conventional and RAFT miniemulsion copolymerizations of butyl methacrylate with fluoromethacrylate and monomer reactivity ratios

Reversible addition fragmentation chain transfer (RAFT) mediated and conventional miniemulsion copolymerizations of butyl methacrylate (BMA) with fluoromethacrylate (FMA) were carried out at 70°C with potassium persulphate as initiator. The kinetics of the copolymerizations was investigated comparatively. Copolymer compositions at low conversion levels were determined by ¹H NMR and FTIR spectra techniques. In the presence of RAFT agent 2‐cyanoprop‐2‐yl dithiobenzoate, the copolymerization of BMA with FMA in miniemulsion was obviously retarded. The copolymerization exhibited typical features of controlled molecular weights and narrow polydispersities. The reactivity ratios were evaluated by Kellen‐Tudos (K‐T) method, which yields the apparent reactivity ratios: r_BMA = 0.73 and r_FMA = 0.75 in conventional copolymerizations, and r_BMA = 0.65 and r_FMA = 0.70 in CPDB‐mediated system. The results show that the monomer FMA with a perfluoroalkyl side chain is slightly more reactive than BMA, and the copolymerizations process have a tendency to crosspropagate and to produce a higher FMA content in the copolymers. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Design and synthesis of zero–zero‐birefringence polymers using N‐methylmaleimide

Zero–zero‐birefringence polymers which exhibit no orientational birefringence and no photoelastic birefringence may be suitable candidates for the components of optical devices. To develop zero–zero‐birefringence polymers, a novel copolymerization system is required. We investigated two types of birefringence of poly(N‐methylmaleimide) (PMeMI) and showed that PMeMI exhibits positive orientational and photoelastic birefringence. On the basis of the results, we calculated the optimal composition for compensating both types of birefringence by solving three equations which describe the relationship between birefringence properties and weight fraction of monomers. When the copolymer compositions were MMA/BzMA/MeMI = 86/8/6 and 88/8/4 (wt %), zero–zero‐birefringence polymers were obtained. By using MeMI as a comonomer, these zero–zero‐birefringence polymers have a much higher glass transition temperature (T_g) than those of previous researches. Also, this polymer film has high transparency comparable with that of PMMA film. Therefore, we conclude that we successfully prepared zero–zero‐birefringence polymers using N‐substituted maleimide and that N‐substituted maleimide is a promising material for zero–zero‐birefringence polymers for optical devices. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40423.     

Free radical copolymerization of N,N‐dimethylaminoethyl methacrylate with styrene and methyl methacrylate: monomer reactivity ratios and glass transition temperatures

BACKGROUND: The properties of copolymers depend strongly on their composition; therefore in order to tailor some for specific applications, it is necessary to control their synthesis, and, in particular, to know the reactivity ratios of their constituent monomers. Free radical copolymerizations of N,N‐dimethylaminoethyl methacrylate (DMAEM) with styrene (ST) and methyl methacrylate (MMA) in toluene solution using 1‐di(tert‐butylperoxy)‐3,3,5‐trimethylcyclohexane as initiator at 70 °C were investigated. Monomer reactivity ratios were determined for low conversions using both linear and nonlinear methods. RESULTS: For the DMAEM/ST system the average values are r₁ = 0.43 and r₂ = 1.74; for the DMAEM/MMA system the average values are r₁ = 0.85 and r₂ = 0.86. The initial copolymerization rate, R_p, for DMAEM/ST sharply decreases as the content of ST in the monomer mixture increases up to 30 mol% and then attains a steady value. For the DMAEM/MMA copolymerization system the composition of the feed does not have a significant influence on R_p. The glass transition temperatures (T_g) of the copolymers were determined calorimetrically and calculated using Johnston's sequence length method. A linear dependence of T_g on copolymer composition for both systems is observed: T_g increases with increasing ST or MMA content. CONCLUSION: Copolymerization reactivity ratios enable the design of high‐conversion processes for the production of copolymers of well‐defined properties for particular applications, such as the improvement of rheological properties of lubricating mineral oils. Copyright © 2009 Society of Chemical Industry     

Complex-radical copolymerization of <Emphasis Type="Italic">N-</Emphasis>vinyl pyrrolidone with isostructural analogs of maleic anhydride

Radical copolymerizations of N-vinyl-2-pyrrolidone (VP) with isostructural analogs of maleic anhydride (MA), such as citraconic anhydride (CA) and N-substituted maleimides [maleimide (MI), N-ethylmaleimide (EMI) and N-phenylmaleimide (PhMI)] were studied. Compositions of copolymers synthesized in a wide range of monomer feed ratios were determined by alkali titration (for anhydride copolymers), FTIR and ¹H NMR spectroscopy using 1495 and 630 cm^-1 (for VP-MI), 1289 and 1225 cm^-1 (for VP-EMI) and 1050 and 3067 cm^-1 (for VP-PhMI) analytical bands and integral areas of CH₂ (pyrrolidone ring) and CH (MI), CH₃ (EMI) and CH= (benzene ring in PhMI) groups, respectively. Electron-donor VP monomer was found to have substantially different reactivities in the radical copolymerization with MA, CA and N-substituted (H, C₂H₅ and phenyl) malemides as electron-acceptor comonomers. Effects of H-bonding and N→O=C coordination on the monomer reactivity ratios were evaluated. Tendency to alternation of the monomer pairs increases in the order of VP–MA > VP–CA > VP-MI > VP-PhMI > VP-EMI. Structure-thermal property-relationship for the synthesized copolymers was also studied.     

Polymerization of 1,3‐dienes containing functional groups: 8. Free‐radical polymerization of 2‐triethoxysilyl‐ 1,3‐butadiene

The presence of a bulky substituent at the 2‐position of 1,3‐butadiene derivatives is known to affect the polymerization behavior and microstructure of the resulting polymers. Free‐radical polymerization of 2‐triethoxysilyl‐1,3‐butadiene ( 1 ) was carried out under various conditions, and its polymerization behavior was compared with that of 2‐triethoxymethyl‐ and other silyl‐substituted butadienes. A sticky polymer of high 1,4‐structure ( ) was obtained in moderate yield by 2,2′‐azobisisobutyronitrile (AIBN)‐initiated polymerization. A smaller amount of Diels–Alder dimer was formed compared with the case of other silyl‐substituted butadienes. The rate of polymerization (R_p) was found to be R_p = k[AIBN]^0.5[ 1 ]^1.2, and the overall activation energy for polymerization was determined to be 117 kJ mol^?1. The monomer reactivity ratios in copolymerization with styrene were r ₁ = 2.65 and r_st = 0.26. The glass transition temperature of the polymer of 1 was found to be ?78 °C. Free‐radical polymerization of 1 proceeded smoothly to give the corresponding 1,4‐polydiene. The 1,4‐E content of the polymer was less compared with that of poly(2‐triethoxymethyl‐1,3‐butadiene) and poly(2‐triisopropoxysilyl‐1,3‐butadiene) prepared under similar conditions. Copyright © 2010 Society of Chemical Industry     

Reactivity ratios of free monomers and their charge‐transfer complex in the copolymerization of N‐butyl maleimide and styrene

As for the charge‐transfer complex (CTC) formed by N‐butyl maleimide (NMBI) and styrene in chloroform, the complex formation constant was determined by ¹H‐NMR of Hanna–Ashbaugh. The copolymerization of NBMI (NBMI, M₁) and styrene (St, M₂) in chloroform using AIBN as an initiator was investigated. On the basis of the kinetic model proposed by Shan, the reactivity ratios of free monomers and CTC in the copolymerization were calculated to be r₁₂ = 0.0440, r₂₁ = 0.0349, r_1C = 0.00688, r_2C = 0.00476, and the ratios of rate constants were obtained to be k_1C/k₁₂ = 6.40, k_2C/k₂₁ = 7.33. In addition, the copolymer was characterized by IR, ¹H‐NMR, DSC, and TGA. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 3007–3012, 2002; DOI 10.1002/app.2330     

Copolymerization of N‐(4‐carboxyphenyl) itaconimide or N‐(4‐carboxyphenyl) itaconamic acid with methyl methacrylate

This paper describes the synthesis and characterization of N‐(4‐carboxyphenyl) itaconamic acid (CPA) and N‐(4‐carboxyphenyl) itaconimide (CPI) obtained by reacting itaconic anhydride with p‐aminobenzoic acid. Structural and thermal characterization of CPA and CPI was done using ¹H‐NMR, FTIR, and differential scanning calorimetry (DSC). Copolymerization of CPA or CPI with methyl methacrylate (MMA) in solution was carried out at 60 °C using azobisisobutyronitrile as an initiator and dimethyl acetamide or THF as solvent. Feed compositions having varying mole fractions of CPA or CPI ranging from 0.05–0.20 or 0.1–0.5 were taken to prepare copolymers. Copolymerizations were terminated at low percentage conversion. Structural characterization of copolymers was done by ¹H‐NMR and elemental analysis. Copolymer composition was determined using percentage nitrogen content. The reactivity ratios were r₁ (MMA) = 0.68 ± 0.06 and r₂ (CPI) = 0.46 ± 0.06. The intrinsic viscosity [η] was determined using an Ubbelohde suspension level viscometer. [η] decreased with increasing mole fraction of N‐(p‐carboxyphenyl) itaconimide or N‐(p‐carboxyphenyl) itaconamic acid in copolymers. Glass transition temperature and thermal stability of the copolymers were determined using DSC and thermogravimetric analysis, respectively. The glass transition temperature (T_g) as determined from DSC scans increased with increasing amounts of CPA or CPI in copolymers. A significant improvement in the char yield was observed upon copolymerization. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1909–1915, 2005     

Kinetics for copolymerization of methyl methacrylate with N‐cyclohexylmaleimide

The kinetics for the radical copolymerization of methyl methacrylate (MMA) with N‐cyclohexylmaleimide (NCMI) was investigated. The initial copolymerization rate R_p is proportional to the initiator concentration to the power of 0.54. The apparent activation energy of the overall copolymerization was measured to be 69.0 kJ/mol. The monomer reactivity ratios were determined to be r_NCMI = 0.42 and r_MMA = 1.63. R_p reduces slightly, and the molecular weight of the resultant copolymer decreases with increasing the concentration of the chain transfer agent N‐dodecanethiol (RSH). The more the transfer agent, the narrower the molecular weight distribution of the resulting copolymer. The following chain‐transfer constant of RSH for the copolymerization of MMA with NCMI in benzene at 50°C was obtained: C_s = 0.23. The glass transition temperature (T_g) of the copolymer increases with increasing f_NCMI, which indicates that adding NCMI can improve the heat resistance of Plexiglas. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1293–1297, 1999     

Copolymerization of 2‐Acrylamido‐2‐methyl‐1‐propanesulfonic Acid and 1‐Vinylimidazole in Ethanol

Polymerization rate and copolymerization parameters of the free‐radical copolymerization of AMPS with 1‐VIm was studied as a function of the monomer feed and the pH value in ethanol. It was found that neutral and basic monomer mixtures containing the sodium salt of AMPS polymerized faster and led to polymers with a higher proportion of NaAMPS incorporated than those monomer mixtures containing the free acid. Additionally, based on the experimental data, copolymerization parameters of r_AMPS = 0.3 and r_1‐VIm = 0.13 were calculated for polymerization in acidic solution and r_AMPS = 4.1 and r_1‐VIm = 0.1 for polymerization in basic and neutral solutions. Finally, the thermal stability, rheological behavior, and intrinsic viscosity were determined for the polymers.

     

Synthesis of poly[(2‐oxo‐1,3‐dioxolan‐4‐yl)methyl vinyl ether‐co‐N‐phenylmaleimide] and its miscibility in blends with styrene‐acrylonitrile or poly(vinyl chloride)

The aim of the study was to investigate the synthesis of a copolymer bearing cyclic carbonate and its miscibility with styrene/acrylonitrile copolymer (SAN) or poly(vinyl chloride) (PVC). (2‐Oxo‐1,3‐dioxolan‐4‐yl)methyl vinyl ether (OVE) as a monomer was synthesized from glycidyl vinyl ether and CO₂ using quaternary ammonium chloride salts as catalysts. The highest reaction rate was observed when tetraoctylammonium chloride (TOAC) was used as a catalyst. Even at the atmospheric pressure of CO₂, the yield of OVE using TOAC was above 80% after 6 h of reaction at 80°C. The copolymer of OVE and N‐phenylmaleimide (NPM) was prepared by radical copolymerization and was characterized by FTIR and ¹H‐NMR spectroscopies and differential scanning calorimetry (DSC). The monomer reactivity ratios were given as r₁ (OVE) = 0.53–0.57 and r₂ (NPM) = 2.23–2.24 in the copolymerization of OVE and NPM. The films of poly(OVE‐co‐NPM)/SAN and poly(OVE‐co‐NPM)/PVC blends were cast from N‐dimethylformamide. An optical clarity test and DSC analysis showed that poly(OVE‐co‐NPM)/SAN and poly(OVE‐co‐NPM)/PVC blends were both miscible over the whole composition range. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1809–1815, 2000     

4‐Acetamidophenyl acrylate copolymers with acrylonitrile and N‐vinyl‐2‐pyrrolidone: Synthesis,characterization, and reactivity ratios

4‐Acetamidophenyl acrylate (APA) was synthesized and characterized by IR, ¹H and ¹³C NMR spectroscopies. Homo‐ and copolymers of APA with acrylonitrile (AN) and N‐vinyl‐2‐pyrrolidone (NVP) were prepared by a free radical polymerization. All the copolymer compositions have been determined by ¹H NMR technique, and the reactivity ratios of the monomer pairs have been evaluated using the linearization methods Fineman–Ross, Kelen–Tudos, and extended Kelen–Tudos. Nonlinear error‐in‐variable model (EVM) method was used to compare the reactivity ratios. The reactivity ratios for copoly(APA–AN) system were APA(r₁) = 0.70 and AN(r₂) = 0.333, and for copoly(APA–NVP) system the values were APA(r₁) = 4.99 and NVP(r₂) = 0.019. Thermal stability and molecular weights of the copolymers are reported. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1919–1927, 2006     

Copolymerization and thermal behavior of methyl methacrylate with N‐(phenyl/p‐tolyl) itaconimides

This study describes the synthesis, characterization, and thermal behavior of copolymers of methyl methacrylate (MMA) and N‐p‐tolyl itaconimide (PTI)/N‐phenyl itaconimide (I). Homopolymerization and copolymerization of N‐(phenyl/p‐tolyl) itaconimide with MMA was carried out by use of various mole fractions of N‐aryl itaconimide in the initial feed from 0.1 to 0.5, using azobisisobutyronitrile as an initiator and tetrahydrofuran as the solvent. The copolymer composition was determined by ¹H‐NMR spectroscopy using the proton resonance signals attributed to –OCH₃ of MMA (δ = 3.5–3.8 ppm) and the aromatic protons (δ = 7.0–7.5 ppm) of N‐aryl itaconimide. The reactivity ratios of the monomers were found to be r₁ (PTI) = 1.33 ± 0.05/r₂ (MMA) = 0.24 ± 0.03 and r₁ (I) = 1.465 ± 0.035/r₂ (MMA) = 0.385 ± 0.005. The molecular weight of the copolymers decreased with increasing mole fraction of N‐aryl itaconimide in the copolymers. Glass‐transition temperature (T_g) and thermal stability of PMMA increased with increasing amounts of itaconimides in the polymer backbone. A significant increase in the percentage char yield at 700°C was observed on incorporation of a low mole fraction of N‐aryl itaconimides. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1195–1202, 2003     

N,N′‐Dioxide‐Magnesium Ditriflate Complex‐Catalyzed Asymmetric α‐Hydroxylation of β‐Keto Esters and β‐Keto Amides

The highly catalytic asymmetric α‐hydroxylation of 1‐tetralone‐derived β‐keto esters and β‐keto amides using tert‐butyl hydroperoxide (TBHP) as the oxidant was realized by a chiral N,N′‐dioxide‐magnesium ditriflate [Mg(OTf)₂] complex. A series of corresponding chiral α‐hydroxy dicarbonyl compounds was obtained in excellent yields (up to 99%) with excellent enantioselectivities (up to 98% ee). The products were easily transformed into useful building blocks and the precursor of daunomycin was achieved in an asymmetric catalytic way for the first time.     

Controlled radical alternating copolymerization of N‐phenyl maleimide with ethyl α‐ethylacrylate by reversible addition fragmentation chain‐transfer process

The alternating copolymerization of N‐phenyl maleimide (NPMI) with ethyl α‐ethylacrylate (EEA) by the reversible addition fragmentation chain‐transfer process was investigated. The monomer reactivity ratios were measured and r₁ = 0.19 ± 0.03 for NPMI and r₂ = 0.20 ± 0.04 for EEA. It was found that before about 45% of the comonomer conversion, the molecular weight of the copolymer increased with the conversion, the molecular weight distribution was rather narrow, and the molecular weight of the copolymer approached a constant value, irrespective of the length of the polymerization time. Electronic spin resonance determined that the radical signal disappeared quickly after the conversion of comonomer exceeded 45%, which may be attributed to the coupling termination of the propagating polymer chains with the EEA end with the intermediate radicals when the concentration of comonomers decreased. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 2376–2382, 2004     

Forgotten monomers: access to α‐modified N‐vinylpyrrolidone polymers via C‐alkylation

Alkylation of N‐vinylpyrrolidone using lithium diisopropylamide and bis(2‐bromoethyl) ether was carried out to obtain 3‐(2‐(2‐bromoethoxy)ethyl)‐1‐vinyl‐2‐pyrrolidone ( 2 ). The derivative 2 represents a versatile starting molecule for further modification via nucleophilic displacement yielding, for example, the bicyclic 2‐vinyl‐8‐oxa‐2‐azaspiro[4.5]decan‐1‐one ( 4 ) or the ammonium salt 3‐diethoxy‐N,N′‐((dimethylbenzyl)ammonium bromide)‐1‐vinyl‐2‐pyrrolidone ( 10 ). Via free radical polymerization of 4 and 10 , the corresponding homopolymers were obtained. Copolymerization of 4 and 10 with N,N′‐diethylacrylamide yielded water‐soluble materials. The thermosensitive solubility of copolymers poly[(2‐vinyl‐8‐oxa‐2‐azaspiro[4.5]decan‐1‐one)‐co‐(N,N′‐diethylacrylamide)] and poly[(3‐diethoxy‐N,N′‐((dimethylbenzyl)ammonium bromide)‐1‐vinyl‐2‐pyrrolidone)‐co‐(N‐vinylpyrrolidone)] in water was investigated. © 2015 Society of Chemical Industry     

Radical copolymerization between methyl methacrylate and N‐cyclohexylmaleimide with thiol as an inifer

N‐dodecanethiol (RSH) was found efficient to initiate the radical copolymerization of methyl methacrylate (MMA) with N‐cyclohexylmaleimide (NCMI) at 40–60°C. The initial copolymerization rate, R_p, increases respectively with increasing [RSH] and the mol fraction of NCMI in the comonomer feed, f_NCMI. The molecular weight of the copolymer decreases with increasing [RSH]. The initiator transfer constant of RSH was determined to be C_I = 0.21. The apparent activation energy of the overall copolymerization was measured to be 46.9 kJ/mol. The monomer reactivity ratios were determined to be r_NCMI = 0.32 and r_MMA = 1.35. The glass transition temperature of the copolymer increases obviously with increasing f_NCMI, which indicates that adding NCMI may improve the heat resistance of plexiglass. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1417–1423, 1999     

Copolymerization of butadiene with styrene using a rare‐earth metal compound – dialkylmagnesium – halohydrocarbon catalytic system

Copolymerizations of butadiene (Bd) with styrene (St) were carried out with catalytic systems composed of a rare‐earth compound, Mg(n‐Bu)₂ (di‐n‐butyl magnesium) and halohydrocarbon. Of all the rare earth catalysts examined, Nd(P₅₀₇)₃–Mg(n‐Bu)₂–CHCl₃ showed a high activity in the copolymerization under certain conditions: [Bd] = [St] = 1.8 mol l^?1, [Nd] = 6.0 × 10^?3 mol l^?1, Mg/Nd = 10, Cl/Nd = 10 (molar ratio), ageing for 2 h, copolymerization at 50 °C for 6–20 h. The copolymer of butadiene and styrene obtained has a relatively high styrene content (10–30 mol%), cis‐1,4 content in butadiene unit (85–90%), and molecular weight ([η] = 0.8–1 dL g^?1). Monomer reactivity ratios were estimated to be r_Bd = 36 and r_St = 0.36 in the copolymerization. © 2002 Society of Chemical Industry