Dynamic mechanical properties of polycarbonate and acrylonitrile–butadiene–styrene copolymer blends

Blends of polycarbonate (PC) and poly(acrylonitrile‐co‐butadiene‐co‐styrene) (ABS) with different compositions are characterized by means of dynamic mechanical measurements. The samples show phase separation. The shift in the temperatures of the main dynamic mechanical relaxation shown by the blend with respect to those of the pure components is attributed to the migration of oligomers present in the ABS toward the PC in the melt blending process. A comparison with other techniques (dielectric and calorimetric analysis) and the application of the Takayanagi three block model confirm this hypothesis. In all the studied blend compositions (ABS weight up to 28.6%) the PC appears as the matrix where a disperse phase of ABS is present. The scanning and transmission electron microscopy micrographs show that the size of the ABS particles increases when the proportion of ABS in the blend increases. The FTIR results indicate that the interaction between both components are nonpolar in nature and can be enhanced by the preparation procedure. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1507–1516, 2002     

Preparation and mechanical properties of acrylonitrile‐butadiene‐styrene copolymer/clay nanocomposites

Bis(3‐triethoxysilylpropyl) tetrasulfane (TSS) was reacted with the silanol groups of the commercially available clay, Closite®25A (C25A) to prepare TSS‐C25A, which was melt‐compounded with acrylonitrile‐butadiene‐styrene copolymer (ABS). The tetra sulfide groups of TSS‐C25A may chemically react with the vinyl groups of ABS to enhance the interaction between the clay and ABS. The ABS/clay composites exhibited much higher tensile strength and elongation at break than the neat ABS. Especially the elongation at break of ABS/TSS‐C25A composite was 5 times higher than that of neat ABS. The X‐ray diffraction patterns of the clay showed that the d₀₀₁ basal spacing was enlarged from 1.89 nm to 2.71–2.86 nm as a result of the compounding with ABS. According to the thermogravimetric analysis, the thermal decomposition of the composite took place at a slightly higher temperature than that of neat ABS. Intercalated/exfoliated coexisting structures were observed by transmission electron microscopy for the ABS/clay composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of compatibilizer in acrylonitrile‐butadiene‐styrene toughened nylon 6 blends: Ductile–brittle transition temperature

The ductile–brittle transition temperatures were determined for compatibilized nylon 6/acrylonitrile‐butadiene‐styrene (PA6/ABS) copolymer blends. The compatibilizers used for those blends were methyl methacrylate‐co‐maleic anhydride (MMA‐MAH) and MMA‐co‐glycidyl methacrylate (MMA‐GMA). The ductile–brittle transition temperatures were found to be lower for blends compatibilized through maleate modified acrylic polymers. At room temperature, the PA6/ABS binary blend was essentially brittle whereas the ternary blends with MMA‐MAH compatibilizer were supertough and showed a ductile–brittle transition temperature at ?10°C. The blends compatibilized with maleated copolymer exhibited impact strengths of up to 800 J/m. However, the blends compatibilized with MMA‐GMA showed poor toughness at room temperature and failed in a brittle manner at subambient temperatures. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2643–2647, 2003     

Compatibilization of polypropylene/Poly(acrylonitrile‐butadiene‐styrene) blends by polypropylene‐graft‐cardanol

The polypropylene‐graft‐cardanol (PP‐g‐cardanol) was prepared by reactive extrusion with polypropylene (PP) and natural renewable cardanol which could increase the interfacial energy of PP and inhibit the degradation of PP during the process of reactive extrusion and usage. In this article, PP‐g‐cardanol and polypropylene‐graft‐maleic anhydride (PP‐g‐MAH) were used as compatibilizers of the polypropylene (PP)/poly(acrylonitrile‐butadiene‐styrene) (ABS) blends. PP/ABS (70/30, wt %) blends with PP‐g‐cardanol and PP‐g‐MAH were prepared by a corotating twin‐screw extruder. From the results of morphological studies, the droplet size of ABS was minimized to 1.93 and 2.01 μm when the content of PP‐g‐cardanol and PP‐g‐MAH up to 5 and 7 phr, respectively. The results of mechanical testing showed that the tensile strength, impact strength and flexural strength of PP/ABS (70/30) blends increase with the increasing of PP‐g‐cardanol content up to 5 phr. The complex viscosity of PP/ABS (70/30) blends with 5 phr PP‐g‐cardanol showed the highest value. Moreover, the change of impact strength and tensile strength of PP/ABS (70/30) blends were investigated by accelerated degradation testing. After 4 accelerated degradation cycles, the impact strength of the PP/ABS (70/30) blends with 5 phr PP‐g‐cardanol decrease less than 6%, but PP/ABS (70/30) blends with 5 phr PP‐g‐MAH and without compatibilizer decrease as much as 12% and 32%, respectively. The tensile strength of PP/ABS (70/30) blends has a similar tendency to that of impact strength. The above results indicated that PP‐g‐cardanol could be used as an impact modifier and a good compatibilizer, which also exhibited better stability performance during accelerated degradation testing. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41315.     

Prediction of the creep of heterogeneous polymer blends: Rubber‐toughened polypropylene/poly(styrene‐co‐acrylonitrile)

A previously proposed predictive format for elastic, storage and loss moduli is extended for the time‐dependent compliance D_b(t) of polymer blends. The format employs a two‐parameter equivalent box model (EBM) and the data on the phase continuity of components in blends obtained by using modified general equations of the percolation theory. As input data, the compliances D₁(t) and D₂(t) and the critical volume fractions V_1cr and V_2cr (delimiting the interval of phase co‐continuity in blends) of components are sufficient. To describe the effect of time on D₁(t), D₂(t) and D_b(t) within the linear stress‐strain region, a routinely used empirical equation was found suitable. Applicability of the proposed format is demonstrated on rubbertoughened polypropylene/poly(styrene‐co‐acrylonitrile) blends consisting of components with markedly different viscoelastic properties. The proposed predictive format fits fairly well the creep behavior of blends over the interval 0.1‐10,000 minutes.     

Morphology,thermal, and mechanical properties of acrylonitrile–butadiene–styrene/carbon black composites

Acrylonitrile–butadiene–styrene (ABS) polymers are susceptible to degradation that increases the yellowness of the polymer, distorts the surface glossy, and affects the mechanical properties. One way to protect ABS against degradation is the addition of carbon black (CB) that can act as a stabilizer. In this work, CB was dispersed in ABS through melt‐compounding. Electron microscopy was used to study the morphology of the filled‐ and unfilled‐ABS, and revealed that the CB particles/aggregates were distributed within the styrene–acrylonitrile (SAN) phase and around the PB phase. The results of the Fourier transform infrared spectroscopy showed that upon processing of ABS, crosslinking in the polybutadiene (PB) phase was the governing degradation mechanism. Increasing the CB content resulted in increasing the heat stability of the ABS/CB compounds, which was confirmed by thermogravimetric analysis. The DTA results showed that the PB degradation peak occurring at about 395°C was disappeared by addition of CB. Impact strength test was performed to study the effect of CB on the toughness of ABS. Impact strength was reduced with increasing CB loading. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Fire performance and mechanical properties of acrylonitrile‐butadiene‐styrene copolymer/modified expandable graphite composites

The fire performance and mechanical properties of an acrylonitrile‐butadiene‐styrene (ABS) copolymer compounded with different expandable graphites (EG) and fire retardants were studied by using the limiting oxygen index test, the UL‐94 test, a mechanical test, and a thermogravimetric analysis. The ground EG treated with phosphoric acid and silane could have the great increase of the volume expansion ratio. The addition of the treated EG in ABS significantly enhances the fire performance but decreases the impact strength of ABS. ABS with the treated EG has a much higher impact strength than with the as‐received EG because of the smaller particle size of the treated EG and the better adhesion between the ABS and the treated EG. The addition of modified ammonium polyphosphate or decabromodiphenyl oxide/antimony trioxide can considerably improve the fire performance of ABS/treated EG composites because of a synergistic effect. The V‐0 grade (UL‐94) ABS composite with the limiting oxygen index of 32.5 can be obtained by adding small amounts of the treated EG and modified ammonium polyphosphate into ABS. Thermogravimetric analysis results indicate that the initial vapor release temperatures and the weight loss rates of ABS/EG composites are closely related to their fire performance and affected by the fire retardant used. Copyright © 2011 John Wiley & Sons, Ltd.     

Preparation and properties of poly(ether‐ester‐amide)/poly(acrylonitrile‐co‐butadiene‐co‐styrene) antistatic blends

A novel antistatic agent poly(ether‐ester‐amide) (PEEA) based on caprolactam, polyethylene glycol, and 6‐aminocaproic acid was successfully synthesized by melting polycondensation. The structure, thermal properties, and antistatic ability of the copolymer were characterized by Fourier transform infrared spectroscopy, differential scanning calorimetry, thermogravimetric analyses, and ZC36 megohmmeter. Test results show that PEEA is a block copolymer with a melting point of 217°C and a thermal decomposition temperature of 409°C, together with a surface resistivity of 10⁸ Ω/sq. Antistatic poly(acrylonitrile‐co‐butadiene‐co‐styrene) (ABS) materials were prepared by blending different content of PEEA to ABS resin. The antistatic performances, morphology, and mechanical properties were investigated. It is indicated that the surface resistivity of PEEA/ABS blends decrease with the increasing PEEA content, and the excellent antistatic performance is obtained when the antistatic agent is up to 10–15%. The antistatic performance is hardly influenced by water‐washing and relative humidity, and a permanent antistatic performance is available. The antistatic mechanism is investigated. The compatibility of the blends was studied by scanning electron microscopy images. The ladder distribution of antistatic agent is formed, and a rich phase of antistatic agent can be found in the surface layer. The elongations at break of the blend are improved with the increasing antistatic agent; the tensile strength and the notched impact strength kept almost the same. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Study of the effect of poly(acrylonitrile‐co‐butadiene‐co‐styrene) on the mechanical properties of an epoxy system

The mechanical properties of an epoxy system containing a diglycidyl ether of bisphenol A and 1,3‐bis(aminomethylcyclohexane) modified with different amounts of poly(acrylonitrile‐co‐butadiene‐co‐styrene) (ABS) were studied. Properties examined include tensile stress, percentage strain, tensile modulus, and tensile toughness determined in tensile tests, Rockwell hardness, and energy and maximum force to break a specimen in Charpy impact tests. The effect of the modification produced with the ABS was also studied using statistical methods including analysis of variance and multiple comparisons. The obtained data showed a significant effect of the modification produced with the ABS on the mechanical properties of this epoxy system, especially with the amount of 5 ABS per hundred parts of resin on the tensile properties and on the hardness. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 461–467, 2004     

Isotactic polypropylene toughened with poly(acrylonitrile–butadiene–styrene): Compatibilizing role of maleic anhydride grafted polypropylene

The β‐nucleating activity and toughening effect of acrylonitrile–butadiene–styrene (ABS) graft copolymer on isotactic polypropylene (iPP) and the compatibilizing role of maleic anhydride grafted polypropylene (PP‐g‐MAH) on the iPP/ABS blends were investigated. The results show that ABS can induce the formation of β‐crystal in iPP, and its β‐nucleating efficiency depends on its concentration and dispersibility. The relative content of β‐crystal form is up to 36.19% with the addition of 2% ABS. The tensile and impact properties of the iPP were dramatically enhanced by introducing ABS. The incorporation of PP‐g‐MAH into the iPP/ABS blends inhibits the formation of β‐crystal. The crystallization peaks of the blends shift toward higher temperature, due to the heterogeneous nucleation effect of PP‐g‐MAH on iPP. The toughness of iPP/ABS blends improved due to favorable interfacial interaction resulting from the compatibilization of PP‐g‐MAH is significantly better than the β‐crystal toughening effect induced by ABS. POLYM. ENG. SCI., 59:E317–E326, 2019. © 2019 Society of Plastics Engineers     

Influence of the tert‐dodecyl mercaptan content in poly(acrylonitrile‐butadiene‐styrene) on properties of chlorinated polyvinyl chloride/poly(acrylonitrile‐butadiene‐styrene) blends

A series of poly(acrylonitrile‐butadiene‐styrene) (ABS) grafting modifiers were synthesized by emulsion grafting poly(acrylonitrile‐styrene) (SAN) copolymer onto polybutadiene (PB) latex rubber particles. The chain transfer reagent tert‐dodecyl mercaptan (TDDM) was used to regulate the grafting degree of ABS and the molecular weight of SAN copolymers. By blending these ABS modifiers with Chlorinated polyvinyl chloride (CPVC) resin, a series of CPVC/ABS blends were obtained. The morphology, compatibility, and the mechanical properties of CPVC/ABS blends were investigated. The scanning electron microscope (SEM) studies showed that the ABS domain all uniformly dispersed in CPVC matrix. Dynamic mechanical analyses (DMA) results showed that the compatibility between CPVC and SAN became enhanced with the TDDM content. From the mechanical properties study of the CPVC/ABS blends, it was revealed that the impact strength first increases and then decreases with the TDDM content, which means that the compatibility between CPVC and the SAN was not the only requirement for maximizing toughness. The decreasing of tensile strength and the elongations might attribute to the lower entanglement between chains of CPVC and SAN. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Rubber‐toughened polypropylene nanocomposite: Effect of polyethylene octene copolymer on mechanical properties and phase morphology

Rubber‐toughened polypropylene (PP)/org‐Montmorillonite (org‐MMT) nanocomposite with polyethylene octene (POE) copolymer were compounded in a twin‐screw extruder at 230°C and injection‐molded. The POE used had 25 wt % 1‐octene content and the weight fraction of POE in the blend was varied in the range of 0–20 wt %. X‐ray diffraction analysis (XRD) revealed that an intercalation org‐MMT silicate layer structure was formed in rubber‐toughened polypropylene nanocomposites (RTPPNC). Izod impact measurements indicated that the addition of POE led to a significant improvement in the impact strength of the RTPPNC, from 6.2 kJ/m² in untoughened PP nanocomposites to 17.8 kJ/m² in RTPPNC containing 20 wt % POE. This shows that the POE elastomer was very effective in converting brittle PP nanocomposites into tough nanocomposites. However, the Young's modulus, tensile strength, flexural modulus, and flexural strength of the blends decreased with respect to the PP nanocomposites, as the weight fraction of POE was increased to 20 wt %. Scanning electron microscopy (SEM) was used for the investigation of the phase morphology and rubber particles size. SEM study revealed a two‐phase morphology where POE, as droplets was dispersed finely and uniformly in the PP matrix. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3441–3450, 2006     

Morphology and mechanical properties of polypropylene and poly(ethylene‐co‐methyl acrylate) blends

The morphology and mechanical properties of isotactic polypropylene (iPP) and poly(ethylene‐co‐methyl acrylate) (EMA) blends were investigated. Various EMA copolymers with different methyl acrylate (MA) comonomer content were used. iPP and EMA formed immiscible blends over the composition range studied. The crystallization and melting reflected that of the individual components and the crystallinity was not greatly affected. The size of the iPP crystals was larger in the blends than those of pure iPP, indicating that EMA may have reduced the nucleation density of the iPP; however, the growth rate of the iPP crystals was found to remain constant. The tensile elongation at break was greatly increased by the presence of EMA, although the modulus remained approximately constant until the EMA composition was greater than 20%. EMA with a 9.0% MA content provided the optimum effect on the mechanical properties of the blends. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 175–185, 2003     

Interfacial strength in short glass fiber reinforced acrylonitrile‐butadiene‐styrene/polyamide 6 blends

The purpose of this study is to derive the apparent interfacial shear strength of short glass fiber reinforced acrylonitrile‐butadiene‐styrene/polyamide 6 (PA6) blends with different PA6 contents. Tensile stress‐strain curves and fiber length distributions are utilized within a continuum micromechanics approach which involves a unified parameter for fiber length distribution efficiency represented as a function of strain. The unique combination of predicted micromechanical parameters is capable of accurately reproducing the mechanical response of the composite to applied strain. In this way, the influence of PA6 on interfacial zone is revealed by outcomes of the predictive method and validated by scanning electron microscopy observations. Favored intermolecular interactions in presence of PA6 chains result in the formation of a PA6 sheathing layer on glass fiber surfaces which in turn causes a drop in the apparent interfacial shear strength. The reason behind is shown to be the shift of the fracture zone from fiber/matrix interface to sheathing layer/matrixinterphase. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Thermal aging of bisphenol-A polycarbonate/acrylonitrile–butadiene–styrene blends

Thermal aging of immiscible bisphenol-A polycarbonate/acrylonitrile–butadiene–styrene (PC/ABS) blends containing 25, 60, and 75% PC and the PC and ABS blend components have been studied. Changes in Izod impact properties and dynamic mechanical spectra are reported following aging at 90, 110, and 130°C for times up to 1500 h. PC/ABS blends containing 60 and 75% PC were found to retain high impact performance following aging at elevated temperatures, compared to the PC blend component. Dynamic mechanical spectroscopy is an effective probe for investigating the structure–property changes occurring and the mechanisms of aging. For PC and ABS, the changes were mainly due to physical aging of the amorphous polymers when aged below the glass-transition temperature. For the PC/ABS blends, oxidative degradation additionally contributes to loss of toughness. Although structure–property changes are related to the behavior of the blend components, additional factors of potential importance for multiphase polymer–polymer systems have been identified, including a redistribution of stabilizers during the blend manufacture. © 1995 John Wiley & Sons, Inc.     

The vibration welding of polycarbonate/acrylonitrile‐butadiene‐styrene blends to themselves and to other resins and blends

The weldabilities of two commercial blends of polycarbonate (PC) and acrylonitrile‐butadiene‐styrene (ABS) to themselves and to several other resins and blends are assessed through 120 Hz vibration welds of 6.35‐ and 3.2‐mm‐thick specimens. While the thicker specimens of both blends have relative weld strengths of 83%, the thinner specimens in one of the grades have a lower relative weld strength of 73%. Welds of thicker specimens of both grades to PC have relative strengths of 85%. Again, welds of thinner specimens of one of the grades to PC have a lower relative strengths of 68%. Welds of the thinner specimens of this grade with ABS have relative strengths of 85%. Welds of this material with poly(butylene terephthalate) (PBT), a PC/PBT blend, modified poly(phenylene oxide), and a poly(phenylene oxide)/polyamide blend, have relative weld strengths of 45%, 26%, 76%, and 20%, respectively.     

Properties of acrylonitrile–butadiene–styrene/polycarbonate blends with styrene–butadiene–styrene block copolymer

The importance of alloys and blends has increased gradually in the polymer industry so that the plastics industry has moved toward complex systems. The main reasons for making polymer blends are the strengthening and the economic aspects of the resultant product. In this study, I attempted to improve compatibility in a polymer blend composed of two normally incompatible constituents, namely, acrylonitrile–butadiene–styrene (ABS) and polycarbonate (PC), through the addition of a compatibilizer. The compatibilizing agent, styrene–butadiene–styrene block copolymer (SBS), was added to the polymer blend in ratios of 1, 5, and 10% with a twin‐screw extruder. The morphology and the compatibility of the mixtures were examined by scanning electron microscopy and differential scanning calorimetry. Further, all three blends of ABS/PC/SBS were subjected to examination to obtain their yield and tensile strengths, elasticity modulus, percentage elongation, Izod impact strength, hardness, heat deflection temperature, Vicat softening point, and melt flow index. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2521–2527, 2004     

Preparation and properties of nano‐CaCO3/acrylonitrile‐butadiene‐styrene composites

CaCO₃/acrylonitrile‐butadiene‐styrene (ABS) and CaCO₃/ethylene‐vinyl acetate copolymer (EVA)/ABS nanocomposites were prepared by melting‐blend with a single‐screw extruder. Mechanical properties of the nanocomposites and the dispersion state of CaCO₃ particles in ABS matrix were investigated. The results showed that in CaCO₃/EVA/ABS nanocomposites, CaCO₃ nanoparticles could increase flexural modulus of the composites and maintain or increase their impact strength for a certain nano‐CaCO₃ loading range. The tensile strength of the nanocomposites, however, was appreciably decreased by adding CaCO₃ nanoparticles. The microstructure of neat ABS, CaCO₃/ABS nanocomposites, and CaCO₃/EVA/ABS nanocomposites was observed by scanning electron microscopy. It can be found that CaCO₃ nanoparticles were well‐dispersed in ABS matrix at nanoscale. The morphology of the fracture surfaces of the nanocomposites revealed that when CaCO₃/EVA/ABS nanocomposites were exposed to external force, nano‐CaCO₃ particles initiated and terminated crazing (silver streak), which can absorb more impact energy than neat ABS. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Influence of epoxy resin on the properties of maleic anhydride functionalized acrylonitrile–butadiene–styrene copolymer toughened polyamide 6 blends

Maleic anhydride functionalized acrylonitrile–butadiene–styrene copolymer (ABS‐g‐MA) was used as an impact modifier of polyamide 6 (PA6). Epoxy resin was introduced into PA6/ABS‐g‐MA blends to further improve their properties. Notched Izod impact tests showed that the impact strength of PA6/ABS‐g‐MA could be improved from 253 to 800 J/m with the addition of epoxy resin when the ABS‐g‐MA content was set at 25 wt %. Differential scanning calorimetry results showed that the addition of epoxy resin made the crystallization temperature and melting temperature shift to lower temperatures; this indicated the decrease in the PA6 crystallization ability. Dynamic mechanical analysis testing showed that the addition of epoxy resin induced the glass‐transition temperature of PA6 and the styrene‐co‐acrylonitrile copolymer phase to shift to higher temperatures due to the chemical reactions between PA6, ABS‐g‐MA, and epoxy resin. The scanning electron microscopy results indicated that the ABS‐g‐MA copolymer dispersed into the PA6 matrix uniformly and that the phase morphology of the PA6/ABS‐g‐MA blends did not change with the addition of the epoxy resin. Transmission electron microscopy showed that the epoxy resin did not change the deformation mechanisms of the PA6/ABS‐g‐MA blends. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Electrical and mechanical properties of acrylonitrile‐butadiene‐styrene/multiwall carbon nanotube nanocomposites prepared by melt‐blending

The electrical properties in polymer/carbon nanotube (CNT) nanocomposites are governed not only by the degree of dispersion but also to a greater extent on the aspect ratio of the CNTs in the final composites. Melt‐mixing of polymer and CNTs at high shear rate usually breaks the CNTS that lowers the aspect ratio of the nanotubes. Thus, homogeneous dispersion of CNTs while retaining the aspect ratio is a major challenge in melt‐mixing. Here, we demonstrate a novel method that involves melt‐blending of acrylonitrile‐butadiene‐styrene (ABS) and in situ polymerized polystyrene (PS)/multiwalled CNT (MWCNT) nanocomposites, to prepare electrically conducting ABS/MWCNT nanocomposites with very low CNT loading than reported. The rationale behind choosing PS/MWCNT as blending component was that ABS is reported to form miscible blend with the PS. Thus, (80/20 w/w) ABS/(PS/MWCNT) nanocomposites obtained by melt‐blending showed electrical conductivity value ≈1.27 × 10^?6 S cm^?1 at MWCNT loading close to 0.64 wt %, which is quite lower than previously reported value for ABS/MWCNT system prepared via solution blending. Scanning electron microscopy and differential scanning calorimetry analysis indicated the formation of homogenous and miscible blend of ABS and PS. The high temperature (100°C) storage modulus of ABS (1298 MPa) in the nanocomposites was increased to 1696 MPa in presence of 0.64 wt % of the MWCNT. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012