On the fractal character of polymer spherulites: an ultra‐small‐angle X‐ray scattering study of poly[(R)‐3‐hydroxybutyrate]

Ultra‐small‐angle X‐ray scattering (USAXS) and small‐angle X‐ray scattering (SAXS) measurements are presented for poly[(R)‐3‐hydroxybutyrate] (PHB) crystallized at room temperature. The USAXS patterns indicated that the spherulites had a radially orientated fibrillar nanostructure with fractal geometry over a length scale ranging from 12 nm up to at least 300 nm, with a mass fractal dimension of approximately 2.7 in aged samples. The SAXS patterns indicated that the fibrils themselves were built up of bundles of crystalline lamellae separated by layers of disordered material, with a period length of approximately 6 nm. The SAXS measurements during primary crystallization gave an initial fractal dimension of 4 during spherulite growth, due to the sharp phase boundary between the spherulites and the melt. Copyright © 2004 Society of Chemical Industry     

Effect of N,N′‐diphenyl adipamide on the formation of the β‐crystalline form in isotactic polypropylene

The polymorphic compositions and mechanical properties of isotactic polypropylene (iPP) samples nucleated by a selective β‐nucleating agent [N,N′‐diphenyl adipamide (DPA)] were investigated with wide‐angle X‐ray diffraction, polarized light microscopy, scanning electron microscopy, and mechanical tests. It was found that β‐phase crystals emerged with the addition of DPA, and the relative proportion of the β‐crystalline form reached the maximum value of 0.97 with the addition of 0.1 wt % DPA. The curved lamellae in the β spherulites were like flowers. The β spherulites were etched more easily than α spherulites because amorphous regions were distributed inside the β spherulites. The Izod notched impact strength increased sharply with the addition of DPA and attained the maximum value of 7.30 kJ/m² (the value of blank iPP was 3.13 kJ/m²) with the addition of 0.1 wt % DPA. An analysis of the misfit factors between DPA and β‐iPP showed that β‐iPP could epitaxially crystallize on the DPA crystal well. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Cation exchange membranes by radiation‐induced graft copolymerization of styrene onto PFA copolymer films. IV. Morphological investigations using X‐ray photoelectron spectroscopy

Morphological investigations of poly(tetrafluoroethylene‐co‐perfluorovinyl ether) (PFA)‐g‐polystyrene sulfonic acid membranes prepared by radiation‐induced graft copolymerization of styrene onto PFA films followed by sulfonation were performed by X‐ray photoelectron spectroscopy. The analyzed materials included grafted film and sulfonated membrane samples having various degrees of grafting. Original PFA film was used as a reference material. The results of the X‐ray photoelectron spectral analysis show that PFA film undergoes changes in terms of chemical compositions and binding energies of its basic elemental components under the influence of membrane preparation procedure, i.e., grafting and sulfonation. The chemical compositions of the surfaces of the membranes were found to be dependent on the degree of grafting unlike the binding energies of their elemental components (C, F, O, and S), which were found to be independent of the degree of grafting. The atomic ratio of F/C was found to decrease drastically with the increase in the degree of grafting and the membranes were found to have almost pure hydrocarbon structure at the layers close to their surfaces where degradation is suggested to be concentrated. The results of these investigations suggest that the morphology of the membranes plays an important role in the chemical degradation of the membranes. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 2455–2463, 2000     

The influence of thermal treatment and processing on the structure and morphology of poly(propylene‐ran‐1‐butene) copolymers

New poly(propylene‐ran‐1‐butene) copolymers were analyzed to study the influence of different processing techniques on their structure and morphology. Wide‐angle X‐ray diffraction allowed determination of the percentage of the γ form and the crystallinity in the samples and also the influence of the percentage of 1‐butene on the cell parameters. Furthermore, it was possible to appraise the contributions of different stacks of lamellae to the small‐angle X‐ray diffraction patterns. © 2001 Society of Chemical Industry     

Crystallization kinetics and melting behavior of poly[(trimethylene terephthalate)‐co‐(29 mol % ethylene terephthalate)] copolyester

The copolyester was characterized as having 71 mol % trimethylene terephthalate units and 29 mol % ethylene terephthalate units in a random sequence according to the NMR spectra. Differential scanning calorimeter (DSC) was used to investigate the isothermal crystallization kinetics in the temperature range (T_c) from 130 to 170°C. The melting behavior after isothermal crystallization was studied using DSC and temperature‐modulated DSC by varying the T_c, the crystallization time, and the heating rate. The DSC thermograms and wide‐angle X‐ray diffraction patterns reveal that the complex melting behavior involves melting‐recrystallization‐remelting and different lamellar crystals. As the T_c increases, the contribution of recrystallization gradually falls and finally disappears. A Hoffman‐Weeks linear plot yields an equilibrium melting temperature of 198.7°C. The kinetic analysis of the growth rates of spherulites and the change in the morphology from regular to banded spherulites indicate that a regime II→III transition occurs at 148°C. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Fully biobased biodegradable poly(l‐lactide)‐b‐poly(ethylene brassylate)‐b‐poly(l‐lactide) triblock copolymers: synthesis and investigation of relationship between crystallization morphology and thermal properties

Well‐defined poly(l ‐lactide‐b‐ethylene brassylate‐b‐l ‐lactide) (PLLA‐b‐PEB‐b‐PLLA) triblock copolymer was synthesized by using double hydroxyl‐terminated PEBs with different molecular weights. Gel permeation chromatography and NMR characterization were employed to confirm the structure and composition of the triblock copolymers. DSC, wide‐angle X‐ray diffraction, TGA and polarized optical microscopy were also employed to demonstrate the relationship between the composition and properties. According to the DSC curves, the cold crystallization peak vanished gradually with decrease of the PLLA block, illustrating that the relatively smaller content of PLLA may lead to the formation of a deficient PLLA type crystal, leading to a decrease of melting enthalpy and melting temperature. Multi‐step thermal decompositions were determined by TGA, and the PEB unit exhibited much better thermal stability than the PLLA unit. Polarized optical microscopy images of all the triblock samples showed that spherulites which develop radially and with an extinction pattern in the form of a Maltese cross exhibit no ring bond. The growth rate of the spherulites of all triblock samples was investigated. The crystallization capacity of PLLA improved with incorporation of PLLA, which accords with the DSC and wide‐angle X‐ray diffraction results. © 2019 Society of Chemical Industry     

Influence of the radiation grafting conditions on the cross‐sectional distribution of poly(vinylbenzyl chloride) grafted polymer onto poly(tetrafluoroethylene‐co‐hexafluoropropylene) films

Poly(vinylbenzyl chloride) (PVBC)‐grafted poly(tetrafluoroethylene‐co‐hexafluoropropylene) (FEP) films were prepared as precursors for ion‐exchange membranes with a radiation grafting technique. A scanning electron microscopy–energy dispersive X‐ray spectroscopy (SEM‐EDX) instrument was used to investigate the effects of the radiation grafting conditions on the distribution profiles of the grafts in the FEP‐g‐PVBC films because the properties of the ion‐exchange membranes were largely affected not only by the degree of grafting (DOG) but also by the distribution of the graft chain. These results indicate that the distribution profile of the grafts largely depended on the grafting parameters, such as the solvent, monomer concentration, film thickness, and irradiation dose. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and characterization of chiral side‐chain liquid‐crystalline polymer containing menthol ester

The synthesis of new chiral side‐chain liquid‐crystalline polysiloxanes containing p‐(allyoxy)benzoxy‐p‐chlorophenyl (ABCH) as mesogenic units and undecylenic acid menthol ester (UM) as chiral nonmesogenic units is presented. The chemical structures of monomers and polymers are confirmed by IR spectroscopy. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) are used to measure thermal properties of those polymers. Mesogenic properties are characterized by polarized optical microscope (POM), DSC, and small‐angle X‐ray diffraction. Analytic results revealed that polymers P₀–P₆ are thermotropic liquid‐crystalline polymers with low glass transition; Polymers P₂–P₆ exhibit chiral smectic liquid‐crystalline properties with marble texture, optical rotation, and a sharp reflection at low angles in X‐ray diffraction; polymers P₀, P₁ only exhibit smectic liquid‐crystalline properties without chirality; and P₇ only exhibits chirality without liquid‐crystalline properties. All the polymers exhibit good thermal stability with temperature of 5% mass loss over 297°C. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2845–2851, 2003     

Correlation between gas transport properties and the morphology/dynamics of crystalline fluorinated copolymer membranes

The crystalline structure, dynamics, and gas transport properties (i.e., the gas permeability, gas diffusion coefficient, and gas solubility coefficient) of poly(tetrafluoroethylene‐co‐perfluoroethylvinylether) (PFA) membranes were systematically investigated via differential scanning calorimetry, wide/small/ultra‐small‐angle X‐ray scattering, and quasielastic neutron scattering measurements. We evaluated the gas transport properties using a constant‐volume/variable‐pressure method. The gas permeability and the gas diffusion coefficient decreased with increasing crystallinity of the PFA membranes at crystallinities below 32%. However, in membranes with a crystallinity of 32% or greater, these parameters depended on the characteristics of the gas molecules, such as their kinetic diameter. The so‐called long spacing period and the thickness of the crystalline/amorphous regions increased with crystallinity according to the small/ultra‐small‐angle X‐ray scattering results. Furthermore, the quasielastic neutron scattering measurements indicated that the scattering law was well fitted to a sum of narrow and broad Lorentzian components. In particular, the narrow components, that is, the local motion of amorphous components and side chains, increased with crystallinity. These results suggest that large gas molecules could pass through the PFA membranes, assisted by the motion in the amorphous region. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45665.     

Development of novel biopolymer blends based on poly(l‐lactic acid), poly((R)‐3‐hydroxybutyrate), and plasticizer

Poly(l ‐lactic acid) (PLLA), a biopolymer that can be derived from renewable resources, is known for its brittleness as a result of slow crystallization rates under supercooling conditions, which is associated with the formation of large spherulites. In addition, the glass transition temperature (T_g) of PLLA is 60°C, such that the polymer chain is immobile at room temperature. These disadvantages make PLLA unsuitable for use in the food packaging sector. In this research, biopolymer blends based on PLLA and poly((R)‐3‐hydroxybutyrate) (PHB), together with tributyl citrate (TBC) as a plasticizer, were developed. TBC was added to increase polymer chain mobility, and to decrease PLLA T_g from 60 to 10°C in blends. Furthermore, the addition of PHB as a nucleating agent to PLLA resulted in an increased proportion of smaller spherulites. Fourier‐transform infrared (FT‐IR) spectroscopy indicated that the carbonyl group and several other characteristic peaks in blends are shifted to lower wavenumber. In addition, polarized optical microscopy experiments confirmed the results of differential scanning calorimetry, FT‐IR, and wide‐angle X‐ray diffraction, showing that PHB enhances the crystallization behavior by acting as a bionucleation. POLYM. ENG. SCI., 54:1394–1402, 2014. © 2013 Society of Plastics Engineers     

Influence of regioirregular structural units on the crystallization of isotactic polypropylene

Seven samples of isotactic polypropylene were examined to study the influence on the formation of the γ crystalline phase of possible regiodefects along the chain. Wide‐angle X‐ray diffraction allowed the determination of the percentage of the γ phase in the samples and ¹³C‐NMR spectroscopy was used to correlate the development of the γ phase with the existence of regioirregular structural units along the chain. Furthermore, it was possible to appraise the contributions given by the different families of lamellae to the small‐angle X‐ray diffraction patterns. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 375–384, 2001     

RuO4 staining and lamellar structure of α‐ and β‐PP

Monoclinic (α) and hexagonal (β) polypropylene (α‐ and β‐PP) were stained in the vapor of a ruthenium tetroxide solution prepared in situ. The effect of staining on the fusion behavior was investigated using a DSC. A staining duration between 10 and 24 h was found suitable for obtaining a good electron contrast between the crystalline and amorphous regions for TEM examination without causing severe damage to the crystals. The spherulites of the water‐quenched α‐PP were found to be composed of very fine cross‐hatched lamellae whose long period was about 10 nm. In comparison, the β‐PP spherulites crystallized isothermally at 130°C had a category 2 morphology and the lamellae have a long period of 20 nm. The morphology of the spherulite boundary varied depending on the contact angle between the lamellae of the neighboring spherulites. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 1529–1538, 1999     

Chemical Structures Formed in Electron Beam Irradiated Poly(tetrafluoroethylene‐co‐hexafluoropropylene) (FEP)

Summary: The perfluorinated copolymer poly(tetrafluoroethylene‐co‐hexafluoropropylene) (FEP) was electron beam irradiated under vacuum at various temperatures ranging from room temperature to a temperature above the melting temperature of FEP. Changes of the chemical structure were analyzed by ¹⁹F solid‐state NMR and IR spectroscopy. Trifluoromethyl end groups were generated as a result of main chain scission at all irradiation temperatures studied. In addition, trifluoromethyl side groups in various environments and double bond structures were formed. Quantitative analysis showed that long‐chain branches were formed at irradiation temperatures above 200 °C. Furthermore, the hexafluoropropylene (HFP) units in FEP were found to be less sensitive to radiation than the perfluoropropyl vinyl ether (PPVE) units in poly[tetrafluoroethylene‐co‐(perfluoropropyl vinyl ether)] (PFA).

¹⁹F solid‐state NMR spectra of FEP.     

Synthesis and characterization of aliphatic polyesteramides mainly composed of alternating diester diamide units from N,N′‐bis(2‐Hydroxyethyl)‐oxamide and diacids

This article provided a convenient method to synthesize aliphatic polyesteramides mainly composed of alternating diester diamide units by polycondensation and chain extension. Two kinds of polyesteramide prepolymers were prepared through melt polycondensation from N,N'‐bis(2‐hydroxyethyl)oxamide and adipic acid or sebacic acid. Chain extension of them was conducted with 2,2′‐(1,4‐phenylene)‐bis(2‐oxazoline) and adipoyl biscaprolactamate as combined chain extenders. The chain extended polyesteramides (ExtPEAs) were characterized by IR, ¹H NMR, differential scanning calorimetry, thermogravimetric analysis, wide‐angle X‐ray scattering, tensile test, and dynamic thermomechanical analysis. The results showed that the ExtPEA(0, m)s were mainly constituted with the diester oxamide alternating units. They had T_m above 140.8°C and the initial decomposition temperature above 298.0°C. They crystallized in similar crystallites to Nylon‐66 and were thermoplastic materials with tensile strength up to 31.47 MPa. POLYM. ENG. SCI., 54:756–765, 2014. © 2013 Society of Plastics Engineers     

Synthesis and characterization of side‐chain liquid‐crystalline ionomers containing quaternary ammonium salt groups

A series of thermotropic side‐chain liquid‐crystalline ionomers (LCIs) containing 4‐(4‐alkoxybenzyloxy)‐4′‐allyloxybiphenyl (M) as mesogenic units and allyl triethylammonium bromide (ATAB) as nonmesogenic units were synthesized by graft copolymerization upon polymethylhydrosiloxane. The chemical structures of the polymers were confirmed by IR spectroscopy. DSC was used to measure the thermal properties of these polymers. The mesogenic properties were characterized by polarizing optical microscopy, DSC, and X‐ray diffraction. Homopolymers without ionic groups exhibit smectic and nematic mesophases. The nematic mesophases of the ionomers disappear and the mesomorphic temperature ranges decrease with increasing concentration of ionic units. The influence of the alkoxy chain length on clearing temperature (T_c) values of ionomers clearly shows an odd‐even effect, similar to that of other side‐chain liquid‐crystalline polymers. The mesomorphic temperature ranges increase with increasing alkoxy chain length when the number of alkoxy carbon is over 3. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2879–2886, 2003     

Microstructural investigation of butt‐fusion joint in high‐density polyethylene pipes using wide‐ and small‐angle X‐ray scattering

The melt fusion zone (MFZ) of polyethylene pipe was investigated employing synchrotron wide‐ and small‐angle X‐ray scattering at various locations in MFZ by changing X‐ray incidence angles to probe three‐dimensional structural features. It was determined that the crystals were oriented in two different modes. One is that the polymer chains are oriented parallel to the joint interface line consistently throughout the MFZ. The other is that the crystals are oriented in particular directions depending on the positions in MFZ. The combination of pressure and melt flow during joining process resulted in such a complex structure. It was notable that the boundary of MFZ against the base material was found to be very different depending on the structures involved such as crystallographic unit orientation, lamellae orientation, crystallinity, and spherulitic morphology. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45668.     

Thermal properties and crystalline structure of liquid crystalline poly(ethylene terephthalate‐co‐2(3)‐chloro‐1,4‐phenylene terephthalate)

Thermal properties and crystalline structure of liquid crystalline (LC) poly(ethylene terephthalate‐co‐2(3)‐chloro‐1,4‐phenylene terephthalate) [copoly(ET/CPT)] were investigated using differential scanning calorimetry (DSC), thermogravimetry (TGA), limiting oxygen index (LOI) measurement, electron dispersive X‐ray analysis (EDX), X‐ray diffractometry, and infrared spectrometry (IR). The thermal transition temperatures of copoly(ET/CPT) were changed with the composition. Copoly(ET/CPT) showed two thermal decomposition steps and the residues at 700°C and LOI values of copoly(ET/CPT) were almost proportional to its chlorine content. The activation energy of thermal decomposition of LC units was very low compared to that of poly(ethylene terephthalate)(PET) units. Crystal structure of copoly(ET/CPT) (20/80) was of triclinic system with the lattice constants of a = 9.98 A?, b = 8.78 A?, c = 12.93 A?, α = 97.4°, β = 96.1°, and γ = 90.8°, which is very close to that of poly(chloro‐p‐phenylene terephthlate) (PCPT) with the lattice constants of a = 9.51 A?, b = 8.61 A?, c = 12.73 A?, α = 96.8°, β = 95.4°, and γ = 90.8°. When copoly(ET/CPT)(50/50) was annealed at 220°C in vacuum, crystallization induced sequential reordering (CISR) was not observed but the heat of fusion was slightly increased due to the increase of the trans isomer content in PET units. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1286–1294, 2002; DOI 10.1002/app.10451     

Sequence distribution,thermal properties,and crystallization studies of poly(trimethylene terephthalate‐co‐1,4‐cyclohexylene dimethylene terephthalate) copolyesters

A series of novel poly(trimethylene terephthalate‐co‐1,4‐cyclohexylene dimethylene terephthalate) (PTCT) with various compositions were synthesized by melt polycondensation of 1,3‐propanediol, 1,4‐cyclohexanedimethanol and dimethyl terephthalate. The resulting copolyesters were characterized using ¹³C and ¹H nuclear magnetic resonance. The average length of both trimethylene terephthalate (TT) and cyclohexylene dimethylene terephthalate (CT) sequences varies from 1 to 10, and the chain structure is statistically random. The crystallization was investigated using wide angle X‐ray diffractometer (WAXD) and differential scanning calorimeter. The WAXD patterns can be divided in two groups according to the composition: copolyesters with less than 35 mol % CT content exhibit PTT‐type lattice, and those with CT unit content higher than 42 mol % crystallize with the PCT‐type lattice. The crystallizability of CT sequence is higher than that of TT sequence. Thermodynamic analysis shows that the comonomer is excluded from the PTT‐type or PCT‐type crystal of the copolyesters. The thermal decomposition temperature of copolyesters increases with increasing CT content, and their thermal stability is improved as compared to that of PTT. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Less‐ordered lamellar structure of intercalated poly(L‐lactide)/organo‐modified montmorillonite hybrids

Hybrids of poly(L ‐lactide)/organophilic clay (PLACHs) have been prepared via a melt‐compounding process using poly(L ‐lactide) (PLLA) and different contents of surface‐treated montmorillonite modified with dimethyl dioctadecyl ammonium‐salt. The crystalline structures of PLLA and dispersion states of clay particles in those PLACHs were investigated by use of wide‐angle X‐ray diffraction, small‐angle X‐ray scattering, transmission electron microscopy (both cross section and replication modes), and polarized optical microscopy. Those structures are viewed from the conformational changes of PLLA chains in the space of a few nanometer widths between silicate galleries to crystalline lamellae of several nanometer thicknesses, and spherulitic textures more than micrometer sizes. After annealing treatments at 115°C for 1 hr, the PLACHs formed coarse‐grained spherulitic textures with 40 μm diameter composed of less‐ordered and fragmented lamellae, caused by the reduced mobility of the PLLA chain due to the dispersed clay particles in the PLLA matrix and the intercalation of the PLLA chains in the silicate galleries. The formation of the interfibril structure accompanied by the fragmented lamellae among the dispersed clay particles was examined. POLYM. ENG. SCI., 46:703–711, 2006. © 2006 Society of Plastics Engineers     

Synthesis and properties of homopolyamide and copolyamides fibers based on 2,6‐bis(p‐aminophenyl)benzo[1,2‐d;5,4‐d′]bisoxazole

A novel aromatic homopolyamide with benzobisoxazole units in the main chain was synthesized with 2,6‐bis(p‐aminophenyl)benzo[1,2‐d;5,4‐d′]bisoxazole and terephthaloyl chloride by low temperature solution polycondensation, the inherent viscosity of which was 1.98 dL/g. The diamine and p‐phenylendiamine with terephthaloyl chloride were used to synthesize the copolyamides. The structures of homopolyamide and copolyamides were characterized by IR spectra, elemental analysis, and wide‐angle X‐ray diffraction. Wide‐angle X‐ray diffraction measurements showed that homopolyamide and copolyamides were predominantly crystallinity. The results of thermal analysis indicated that the thermal stabilities of the copolymer increased with an increase of the molar fraction of benzobisoxazole in the copolymers. The thermal stability of the copolyamides with decomposition temperatures (at 10% weight loss) above 570°C was better than that of poly(p‐phenylene terephthalamide) (PPTA). Fibers of homopolyamide and copolyterephthalamides were spun from lyotropic liquid crystal dope in 100% H₂SO₄. When compared with PPTA fibers prepared under the same conditions, the tensile strengths of copolyamides fibers improved by 20–33% with tensile strengths of 1.81 GPa, tensile moduli of 76 GPa, and elongations at break of 3.8–4.1%, which indicated that copolyamides fibers had outstanding mechanical properties. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008