Compatibilization of polypropylene/ poly(3‐hydroxybutyrate) blends

Blending polypropylene (PP) with biodegradable poly(3‐hydroxybutyrate) (PHB) can be a nice alternative to minimize the disposal problem of PP and the intrinsic brittleness that restricts PHB applications. However, to achieve acceptable engineering properties, the blend needs to be compatibilized because of the immiscibility between PP and PHB. In this work, PP/PHB blends were prepared with different types of copolymers as possible compatibilizers: poly(propylene‐g‐maleic anhydride) (PP–MAH), poly (ethylene‐co‐methyl acrylate) [P(E–MA)], poly(ethylene‐co‐glycidyl methacrylate) [P(E–GMA)], and poly(ethylene‐co‐methyl acrylate‐co‐glycidyl methacrylate) [P(E–MA–GMA)]. The effect of each copolymer on the morphology and mechanical properties of the blends was investigated. The results show that the compatibilizers efficiency decreased in this order: P(E–MA–GMA) > P(E–MA) > P(E–GMA) > PP–MAH; we explained this by taking into consideration the affinity degree of the compatibilizers with the PP matrix, the compatibilizers properties, and their ability to provide physical and/or reactive compatibilization with PHB. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Thermoplastic elastomeric blend of nitrile rubber and poly(styrene‐co‐acrylonitrile). I. Effect of mixing sequence and dynamic vulcanization on mechanical properties

The effects of dynamic vulcanization and blend ratios on mechanical properties and morphology of thermoplastic elastomeric (TPE) compositions, based on blends of nitrile rubber (NBR) and poly(styrene‐co‐acrylonitrile) (SAN), were studied. The TPE composition prepared by adding a rubber‐curatives masterbatch to softened SAN yields higher mechanical properties than that prepared by adding curatives to the softened plastic–rubber preblend. The blends having a higher rubber–plastic ratio (60 : 40 to 80 : 20) display thermoplastic elastomeric behavior, whereas those having a higher plastic–rubber ratio (50 : 50 to 90 : 10) display the behavior of impact‐resistant plastics. DSC studies revealed that NBR and SAN are thermodynamically immiscible. SEM studies of the thermoplastic elastomeric compositions show that SAN forms the matrix in which fine particles of NBR form the dispersed phase. It was further confirmed by dynamic mechanical thermal analysis. Dynamic vulcanization causes a decrease in the size of dispersed particles and improvement in mechanical properties. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1976–1987, 2003     

Surface modification effects of core–shell rubber particles on the toughening of poly(butylene terephthalate)

We toughened poly(butylene terephthalate) (PBT) by loading core–shell rubber (CSR) type impact modifiers, consisting of a rubbery poly(n‐butyl acrylate) core and a rigid poly(methyl methacrylate) shell. To optimize the dispersion of CSR particles into the PBT matrix during melt compounding, the shell surface was modified with different grafting ratios of glycidyl methacrylate (GMA) reactive with PBT chain ends. In PBT blends with a 20 wt % CSR loading, the dispersed rubbery phases showed discernible shapes depending on the grafted GMA content, from predetermined spheres with 0.25 ± 0.05 μm diameters to their aggregates in the 2–3 μm diameter range. As a result, the interparticle spacing (τ) could be controlled from 0.25 to 4.0 μm in the PBT blends containing the fixed rubber loading. The Izod impact strengths of these samples increased significantly below τ = 0.4 μm. Additional thermal and morphological analyses strongly supported the hypothesis that the marked increase in toughness of the blends was related to less ordered lamellar formation of the PBT matrix under the confined geometry. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Design of highly tough poly(l‐lactide)‐based ternary blends for automotive applications

Technical renewable poly(l ‐lactide) (PLA)‐based blends represent an elegant way to achieve attractive properties for engineering applications. Recently, the miscibility between PLA and poly(methyl methacrylate) (PMMA) gave rise to new formulations with enhanced thermo‐mechanical properties but their high brittleness still remains a challenge to be overcome. This work here focuses on rubber‐toughened PLA/PMMA formulations for injection‐molding processes upon the addition of a commercially available ethylene‐acrylate impact modifier (BS). The miscibility between PLA and PMMA is not altered by the presence of BS but the incorporation of BS (17% by weight) into a PLA/PMMA matrix could enhance both ductility and toughness of PLA/PMMA blends for PMMA content up to 50 wt %. An optimum range of particle sizes (d_n ～0.5 µm) of the dispersed domains for high impact toughness is identified. These bio‐based ternary blends appear as promising alternatives to petro‐sourced blends such as ABS‐based blends in engineering injection‐molding parts. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43402.     

Complexation of poly(dimethylsiloxane)/poly(methyl methacrylate‐co‐butyl acrylate‐co‐methacrylic acid) latex with poly(dimethylsiloxane)/poly(vinyl acetate‐co‐butyl acrylate) latex

Two latices—the poly(dimethylsiloxane) (PDMS)/poly(methyl methacrylate‐co‐butyl acrylate‐co‐methacrylic acid) system (PA latex) and the PDMS/poly(vinyl acetate‐co‐butyl acrylate) system (PB latex)—were prepared by seeded emulsion polymerization, and PA/PB complex latices were obtained through the interparticle complexation of the PA latex with the PB latex. In addition, for the further study of the interparticle complexation of the PA latex with the PB latex, copolymer latices [PDMS/methyl methacrylate‐co‐butyl acrylate‐co‐vinyl acetate‐co‐methacrylic acid) (PC)] were prepared according to the monomer recipe of the complex latices and the polymerization process of the component latices. The properties of the obtained polymer latices and complex latices were investigated with surface‐tension, contact‐angle, and viscosity measurements. The mechanical properties of the coatings obtained from the latices were investigated with tensile‐strength measurements. The results showed that, in comparison with the two component latices (PA latex and PB latex) and the corresponding copolymer latices (PC latices), the PA/PB complex latices had lower surface tension, lower viscosities, and better wettability to different substrates. The tensile strengths of the coatings obtained from the complex latices were higher than the tensile strengths of the coatings from the two component latices and copolymer latices. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2522–2527, 2004     

Blends of poly(vinyl chloride) (PVC)/natural rubber‐g‐(styrene‐co‐methyl methacrylate) for improved impact resistance of PVC

To improve the mechanical properties of poly(vinyl chloride) (PVC), the possibility of combining PVC with elastomers was considered. Modification of natural rubber (NR) by graft copolymerization with methyl methacrylate (MMA) and styrene (St) was carried out by emulsion polymerization by using redox initiator to provide an impact modifier for PVC. The impact resistance, dynamic mechanical analysis (DMA), and scanning electron microscopy (SEM) of St and MMA grafted NR [NR‐g‐(St‐co‐MMA)]/PVC (graft copolymer product contents of 5, 10, and 15%) blends were investigated as a function of the amount of graft copolymer product. It was found that the impact strength of blends was increased with an increase of the graft copolymer product content. DMA studies showed that NR‐g‐(St‐co‐MMA) has partial compatibility with PVC. SEM confirmed a shift from brittle failure to ductility with an increase graft copolymer content in the blends. The mechanical properties showed that NR‐g‐(St‐co‐MMA) interacts well with PVC and can also be used as an impact modifier for PVC. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1666–1672, 2004     

Effect of ageing and annealing on the mechanical behaviour and biodegradability of a poly(3‐hydroxybutyrate) and poly(ethylene‐co‐methyl‐acrylate‐co‐glycidyl‐methacrylate)blend

Poly(3‐hydroxybutyrate) (PHB) undergoes an ageing process that contributes to its remarkable fragility. Blending it with an elastomer is a possibility to increase toughness. In this work, the mechanical properties of a 70/30 wt% blend of PHB and poly(ethylene‐co‐methyl‐acrylate‐co‐glycidyl‐methacrylate) were studied over time. The phenomenon of ageing affected the blend, which lost its ductility and became fragile days after its processing. Differential scanning calorimetry and small angle X‐ray scattering analyses showed that this drop in mechanical properties was due to changes in the crystalline structure of the matrix. Annealing reduced fragility, increased toughness and prevented a re‐ageing of the blend. Biodegradation in soil was also more intense for annealed samples. © 2013 Society of Chemical Industry     

Influence of aliphatic amine epoxy hardener on the adhesive properties of blends of mono‐carboxyl‐terminated poly(2‐ethylhexyl acrylate‐co‐methyl methacrylate) with epoxy resin

The adhesive properties have been investigated in blends of mono‐carboxyl‐terminated poly(2‐ethylhexyl acrylate‐co‐methyl methacrylate) with diglycidyl ether of bisphenol A and three different aliphatic amine epoxy hardener. The adhesives properties are evaluated in steel alloy substrate using single‐lap shear test. The copolymers are initially miscible in the stoichiometric blends of epoxy resin and hardener at room temperature. Phase separation is noted in the course of the polymerization reaction. Different morphologies are obtained according to the amine epoxy hardener. The most effective adhesive for steel–steel joints in single‐lap shear test is the blends using 1‐(2‐aminoethyl)piperazine (AEP) as hardener. This system shows the biggest lap shear strength. However, the modified adhesives show a reduction in the mechanical resistance. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Influence of granulometry and organic treatment of a Brazilian montmorillonite on the properties of poly(styrene‐co‐n‐butyl acrylate)/layered silicate nanocomposites prepared by miniemulsion polymerization

The influence of granulometry and organic treatment of a Brazilian montmorillonite (MMT) clay on the synthesis and properties of poly(styrene‐co‐n‐butyl acrylate)/layered silicate nanocomposites was studied. Hybrid latexes of poly(styrene‐co‐butyl acrylate)/MMT were synthesized via miniemulsion polymerization using either sodium or organically modified MMT. Five clay granulometries ranging from clay particles smaller than 75 μm to colloidal size were selected. The size of the clay particles was evaluated by specific surface area measurements (BET). Cetyl trimethyl ammonium chloride was used as an organic modifier to enhance the clay compatibility with the monomer phase before polymerization and to improve the clay distribution and dispersion within the polymeric matrix after polymerization. The sodium and organically modified natural clays as well as the composites were characterized by X‐ray diffraction analysis. The latexes were characterized by dynamic light scattering. The mechanical, thermal, and rheological properties of the composites obtained were characterized by dynamical‐mechanical analysis, thermogravimetry, and small amplitude oscillatory shear tests, respectively. The results showed that smaller the size of the organically modified MMT, the higher the degree of exfoliation of nanoplatelets. Hybrid latexes in presence of Na‐MMT resulted in materials with intercalated structures. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Dynamic mechanical properties of semi‐interpenetrating polymer network‐based on nitrile rubber and poly(methyl methacrylate‐co‐butyl acrylate)

In this article, semi‐interpenetrating polymer network (Semi‐IPNs) based on nitrile rubber (NBR) and poly(methyl methacrylate‐co‐butyl acrylate) (P(MMA‐BA)) were synthesized. The structure and damping properties of the prepared Semi‐IPNs blends were characterized and by fourier transform infrared spectrum (FTIR), dynamic mechanical analysis (DMA), scanning electron microscopy (SEM), thermogravimetric analysis (TGA/DTG), and tensile mechanical properties. The results showed that interpenetrating network based on P(MMA‐BA) and NBR was successfully obtained, which showed the improved thermal stability compared to NBR/P(MMA‐BA)‐based two‐roll mill blends. Furthermore, Semi‐IPNs showed significantly better the dynamic mechanical properties than that of the two‐roll mill system. With the increasing feed ratio of BA and MMA during the preparation of Semi‐IPNs, the loss peak position for P(MMA‐BA) in NBR/PMMA IPNs shifted to a lower temperature from 20°C to ?17°C, and when NBR in Semi‐IPNs was accounted for 40 wt %, the dynamic mechanical thermal analysis showed that much more advanced damping material with wider temperature range (?30°C < T < 80°C) as tan δ > 0.45 can be achieved. Therefore, it was expected as a promising way to obtain the excellent damping materials with good oil‐resisted properties according the Semi‐IPNs system. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40217.     

Preparation of thermoplastic elastomer nanocomposites based on polyamide‐6/polyepichlorohydrin‐co‐ethylene oxide

This work is aimed at determining the effect of nanoclay and polyepichlorohydrin‐co‐ethylene oxide (ECO) content on the microstructure and mechanical properties of PA6/ECO thermoplastic elastomers (TPEs). TPE nanocomposites were prepared in a laboratory mixer using polyamide 6 (PA6), ECO, and an organoclay by a two‐step melt mixing process. First, the PA6 was melt blended with Cloisite 30B and then mixed by ECO rubber. X‐ray diffraction results and transmission electron microscopy image showed that the nanoclay platelets were nearly exfoliated in both the phases. The SEM photomicrograph of PA6 with ECO showed that the elastomer particles are dispersed throughout the polyamide matrix and the size of rubber particles is less than 3 μm. Introduction of organoclay in the PA6 matrix increased the size of dispersed rubber particles in comparison with the unfilled but otherwise similar blends. The nanoscale dimension of the dispersed clay results in an improvement of the tensile modulus of the nanocomposites. POLYM. ENG. SCI., 2011. © 2010 Society of Plastics Engineers     

Investigation on the morphological and mechanical properties of (polyamide 6)/(poly[styrene‐co‐acrylonitrile])/(poly[styrene‐b‐{ethylene‐co‐butylene}‐b‐styrene]) ternary blends

In this work, ternary polymer blends based on (polyamide 6)/(poly[styrene‐co‐acrylonitrile])/(poly[styrene‐b‐{ethylene‐co‐butylene}‐b‐styrene]) (SEBS) triblock copolymer and a varying concentration of the reactive (maleic anhydride)‐grafted SEBS were prepared by using a melt‐blending process. The effects of the material parameters (composition of ternary blends and SEBS/[{maleic anhydride}‐grafted SEBS] concentration ratio) and blending sequence on the morphological and mechanical properties of ternary blends were studied. Taguchi experimental design methodology was employed to design the experiments and select the material and processing parameters for the optimized mechanical properties. Tensile properties (Young's modulus and yield stress) and impact strength were considered as the response variables. It was demonstrated that there is a meaningful relationship between the composition of blends, processing parameters, observed phase structure, and obtained mechanical properties. The mechanical tests showed that the highest impact strength was achieved as the dispersion of the rubbery phase achieved an optimum size of about 1 μm. J. VINYL ADDIT. TECHNOL., 23:329–337, 2017. © 2015 Society of Plastics Engineers     

Fracture properties of epoxy/poly(styrene‐co‐allylalcohol) blends

The epoxy/polystyrene system is characterized by a poor adhesion between the constituent phases, which determines its mechanical properties. The adhesion can be improved via blends based on epoxy resin and random copolymers, poly(styrene‐co‐allylalcohol) (PS‐co‐PA). In this work, the influence of PS‐co‐PA content and the good adhesion between the phases on the tensile properties and the fracture toughness achieved through instrumented Charpy tests have been investigated. The tensile strength and the deformation at break showed an increase in the PS‐co‐PA content while the Young's modulus remained the same. The tensile fracture surfaces revealed that the improvement of these magnitudes was mainly due to a crack deflection mechanism. Also, the fracture toughness of the blends was superior to that of the pure epoxy resin. The main operating toughening mechanism was crack deflection. The fractographic analysis showed that ～ 80% of the particles were broken, and the crack tended to divert from its original path through the broken PS‐co‐PA particles. The remaining particles were detached from the epoxy resin, and the holes left suffered plastic deformation. Analytical models were used to predict successfully the toughness due to these mechanisms. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Preparation of PBAS core-shell structured polymer by seeded emulsion polymerization and investigation in AS resin toughness

The preparation of poly(n-butyl acrylate)/poly(acrylonitrile-co-styrene), i.e., poly(BA)/poly(AN-co-St) (PBAS) core-shell structured modifier with controlled particle size was reported, and the mechanical properties of AS/PBAS blends were investigated. The modifier was prepared at a solid content of 50 wt % by a two-stage sequential emulsion polymerization. Dynamic light scattering (DLS) was used to monitor the particle diameters and showed that the particles grew without significant secondary nucleation occurring. The morphology was confirmed by means of transmission electron microscopy (TEM). According to the research on mechanical properties of the AS/PBAS blends, a remarkable toughening effect of PBAS on AS resin was found. By means of scanning electron microscopy (SEM) observation, the toughening mechanism was proposed to be crazing caused by rubber particles and shear yielding of AS matrix. Uniform dispersion of rubber particles in AS matrix was attributed to the good compatibility between AS and PBAS modifier. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Influence of the degree of grafting on the morphology and mechanical properties of blends of poly(butylene terephthalate) and glycidyl methacrylate grafted poly(ethylene‐co‐propylene) (EPR)

Poly(ethylene‐co‐propylene) (EPR) was functionalized to varying degrees with glycidyl methacrylate (GMA) by melt grafting processes. The EPR‐graft‐GMA elastomers were used to toughen poly(butylene terephthalate) (PBT). Results showed that the grafting degree strongly influenced the morphology and mechanical properties of PBT/EPR‐graft‐GMA blends. Compatibilization reactions between the carboxyl and/or hydroxyl of PBT and epoxy groups of EPR‐graft‐GMA induced smaller dispersed phase sizes and uniform dispersed phase distributions. However, higher degrees of grafting (>1.3) and dispersed phase contents (>10 wt%) led to higher viscosities and severe crosslinking reactions in PBT/EPR‐graft‐GMA blends, resulting in larger dispersed domains of PBT blends. Consistent with the change in morphology, the impact strength of the PBT blends increased with the increase in EPR‐graft‐GMA degrees of grafting for the same dispersion phase content when the degree of grafting was below 1.8. However, PBT/EPR‐graft‐GMA1.8 displayed much lower impact strength in the ductile region than a comparable PBT/EPR‐graft‐GMA1.3 blend (1.3 indicates degree of grafting). Morphology and mechanical results showed that EPR‐graft‐GMA 1.3 was more suitable in improving the toughness of PBT. SEM results showed that the shear yielding properties of the PBT matrix and cavitation of rubber particles were major toughening mechanisms. Copyright © 2006 Society of Chemical Industry     

Mechanical properties and surface morphology of photodegraded polyoxymethylene modified by a core–shell acrylate elastomer with UV stabilization

In order to improve the photostability of polyoxymethylene (POM), a core‐shell acrylate elastomer with UV stabilization, i.e. poly[(methyl methacrylate)‐(butyl acrylate)‐2‐hydroxy‐4‐(3‐methacryloxy‐2‐hydroxypropoxy)benzophenone] (core‐shell poly(MMA‐BA‐BPMA)), was added into the POM matrix using a melt‐mixing method. The effect of the modification with core‐shell poly(MMA‐BA‐BPMA) on POM was compared with that of poly(MMA‐ co ‐BA‐ co ‐BPMA) copolymer. Scanning electron microscopy, metallographic microscopy, Fourier transform infrared spectroscopy, differential scanning calorimetry, X‐ray diffraction and X‐ray photoelectron spectroscopy were employed to characterize POM blends before and after UV irradiation, and the mechanical properties of the POM blends were investigated. The results showed that core‐shell poly(MMA‐BA‐BPMA) improved well the compatibility with and toughness of the POM matrix, and its light‐stable functional groups could increase the UV resistance of POM blends. During UV aging, the impact strength and elongation at break of POM/core‐shell poly(MMA‐BA‐BPMA) blends were retained, the growth rate of surface cracks of POM was inhibited effectively by core‐shell poly(MMA‐BA‐BPMA) and the degree of photo‐oxidation of POM blend surfaces was improved to a certain extent. Compared with poly(MMA‐ co ‐BA‐ co ‐BPMA), core‐shell poly(MMA‐BA‐BPMA) had a better UV stabilization effect on the POM matrix. Our results indicate that the core‐shell acrylate elastomer with toughening and UV stabilization functions can significantly improve the long‐term UV stability of POM. Copyright © 2012 Society of Chemical Industry     

n‐Butyl acrylate based latex interpenetrating polymer networks used as processing modifiers and impact modifiers of poly(vinyl chloride)

A latex interpenetrating polymer network (LIPN), consisting of poly(n‐butyl acrylate), poly(n‐butyl acrylate‐co‐ethylhexyl acrylate), and poly(methyl methacrylate‐co‐ethyl acrylate) and labeled PBEM, with 1,4‐butanediol diacrylate as a crosslinking agent was synthesized by three‐stage emulsion polymerization. The initial poly(n‐butyl acrylate) latex was agglomerated by a polymer latex containing an acrylic acid residue and then was encapsulated by poly(n‐butyl acrylate‐co‐ethylhexyl acrylate) and poly(methyl methacrylate‐co‐ethyl acrylate). A polyblend of poly(vinyl chloride) (PVC) and PBEM was prepared through the blending of PVC and PBEM. The morphology and properties of the polyblend were studied. The experimental results showed that the processability and impact resistance of PVC could be enhanced considerably by the blending of 6–10 phr PBEM. This three‐stage LIPN PBEM is a promising modifier for manufacturing rigid PVC. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1168–1173, 2004     

Microfluidic assembly of uniform fluorescent microbeads from quantum‐dot‐loaded fluorine‐containing microemulsion

We report a facile strategy for fabricating fluorescent quantum dot (QD)‐loaded microbeads by means of microfluidic technology. First, a functional fluorine‐containing microemulsion was synthesized with poly[(2‐(N‐ethylperfluorobutanesulfonamido)ethyl acrylate)‐co‐(methyl methacrylate)‐co‐(butyl acrylate)] (poly(FBMA‐co‐MMA‐co‐BA)) as the core and glycidyl methacrylate (GMA) as the shell via differential microemulsion polymerization. Then, CdTe QDs capped with N‐acetyl‐l ‐cysteine (NAC) were assembled into the poly(FBMA‐co‐MMA‐co‐BA‐co‐GMA) microemulsion particles through the reaction of the epoxy group on the shell of the microemulsion and the carboxyl group of the NAC ligand capped on the QDs. Finally, fluorescent microbeads were fabricated using the CdTe QD‐loaded fluorine‐containing microemulsion as the discontinuous phase and methylsilicone oil as the continuous phase by means of a simple microfluidic device. By changing flow rate of methylsilicone oil and hybrid microemulsion system, fluorescent microbeads with adjustable sizes ranging from 290 to 420 µm were achieved. The morphology and fluorescent properties of the microbeads were thoroughly investigated using optical microscopy and fluorescence microscopy. Results showed that the fluorescent microbeads exhibited uniform size distribution and excellent fluorescence performance. © 2014 Society of Chemical Industry     

Acrylate/EVA reactive blends and semi‐IPN: Chemical,chemical–physical,and thermo‐optical characterization

In the present work, blends between poly(methyl methacrylate) (PMMA) or its copolymer with butyl methacrylate P(MMA‐co‐BMA) and poly(ethylene‐co‐vinyl acetate) (EVA) rubbers obtained applying the reactive blending principles were deeply investigated to clarify the chemistry of the system. A copolymeric phase, which is created in situ, was isolated and its chemical structure was determined through NMR analysis. The blends were also crosslinked with a flexible dimethacrylate to realize semi‐interpenetrated networks. The blends were characterized for their properties of interest (mechanical and optical behaviors). Particularly, an accurate investigation of the optical properties as a function of the temperature was performed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Film formation from pigmented latex systems: Mechanical and surface properties of ground calcium carbonate/functionalized poly(n‐butyl methacrylate‐co‐n‐butyl acrylate) latex blend films

The mechanical and surface properties of films prepared from model latex/pigment blends were studied using tensile tests, surface gloss measurements, and atomic force microscopy. Functionalized poly(n‐butyl methacrylate‐co‐n‐butyl acrylate) [P(BMA/BA)] and ground calcium carbonate (GCC) were used as latex and extender pigment particles, respectively. The critical pigment volume concentration of this pigment/latex blend system was found to be between 50 and 60 vol % as determined by surface gloss measurement and tensile testing of the blend films. As the pigment volume concentration increased in the blends, the Young's modulus of the films increased. Nielsen's equations were found to fit the experimental data very well. When the surface coverage of carboxyl groups on the latex particles was increased, the yield strength and Young's modulus of the films both increased, indicating better adhesion at the interfaces between the GCC and latex particles. When the carboxyl groups were neutralized during the film formation process, regions with reduced chain mobility were formed. These regions acted as a filler to improve the modulus of the copolymer matrix and the modulus of the resulting films. The carboxyl groups on the latex particle surfaces increased the surface smoothness of the films as determined by surface gloss measurement. When the initial stabilizer coverage of the latex particles was increased, the mechanical strength of the resulting films increased. At the same time, rougher film surfaces also were observed because of the migration of the stabilizer to the surface during film formation. With smaller‐sized latex particles, the pigment/latex blends had higher yield strength and Young's modulus. Higher film formation temperatures strengthen the resulting films and also influence their surface morphology. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4550–4560, 2006