Thermodynamic properties of 2,2,2-trifluoroethanol

(p, V, T) data for 2,2,2-trifiuoroethanol (TFE) have been obtained in the form of volume ratios for six temperatures in the range 278.15 to 338.15 K for pressures up to 280 MPa. Isothermal compressibilities, isobaric expansivities, and internal pressures have been evaluated from the volumetric data. The compressibilities and internal pressures indicate that the behavior of TFE is closer to that of methanol than of ethanol for most of the pressure range. The use of only the present volumetric results together with the requirement that the B coefficient of the Tait equation should become equal to the negative of the critical pressure at the critical temperature provides interpolations and extrapolations up to 413 K of comparable accuracy.     

Volumetric and thermodynamic properties of liquid 2-fluoroethanol

p-V T data for liquid 2-fluoroethanol (FE) have been obtained in the form of volume ratios at six temperatures (278.15, 288.15, 298.14, 313.14, 323.14, and 338.130 K) at pressures from atmospheric to 314 MPa or higher. Freezing pressures have also been measured in the temperature range from the normal freezing point to 288 K. Densities at atmospheric pressure in the same temperature range as that for thep V T data are also reported. Isothermal compressibilities, isobaric expansivities, changes in the isobaric heat capacity, and internal pressures have been calculated from the volumetric data. Representation of the volume ratios for FE, 2,2-difluoroethanol, 2,2,2-trifluoroethanol, and ethanol by a form of the modified Tait equation shows that the effect of the progressive substitution of fluorine into ethanol cannot be represented by a simple correlation.     

An automated volumometer: Thermodynamic properties of 1,1-dichloro-2,2,2-trifluoroethane (R123) for temperatures of 278.15 to 338.15 K and pressures of 0.1 to 380 MPa

An automated bellows volumometer is described which is capable of obtaining p-V-T data in the form of volume ratios for pressures up to 380 MPa. Volume ratios for 1,1-dichloro-2,2,2-trifluoroethane (R123) have been measured for six temperatures in the range of 278.15 to 338.15 K in the liquid phase. The accuracy of the volume ratios is estimated to be ±0.05 to 0.1% for the experimental temperatures up to 298.15 K and better than ±0.15% for temperatures above the normal boiling point of R123 (300.15 K). They agree with the literature data (which do not extend beyond 4 MPa) within the experimental uncertainty of those results. Isothermal compressibilities, isobaric expansivities, internal pressures, and isobaric molar heat capacities have been evaluated from the volumetric data. The pressure dependence of isobaric molar heat capacities obtained from the data generally agree with the pressure dependence of experimentally measured literature values within the latter's accuracy of ±0.4%.     

Vapor pressure and liquid and gas densities of 2,2,2-trifluoroethanol

Forty-three vapor pressures were measured for temperatures from the normal boiling point to the critical point. These data were obtained with a phase-equilibrium cell designed for precise static measurements at pressures up to 20 MPa. The cell is located within an oil-operated thermostatic bath which provides a homogeneous temperature field with variations less than ±1 mK. The vapor pressure data were fitted to a Wagner-type equation. Sixty-two liquid densities were measured on seven isotherms between 20 and 140°C for pressures up to 16 MPa. These measurements were carried out with a precision density meter operating on a vibrational technique. Sixty-nine gas-PVT triples were determined from Burnett expansion series on five isotherms between 140 and 200°C for pressures up to the saturation line. In all experiments, temperature measurements were made with platinum resistance thermometers. Precise pressure measurements were performed using a mercury column of 6-m height and a standard deadweight gauge for the higher pressures.Paper presented at the Tenth Symposium on Thermophysical Properties, June 20–23, 1988, Gaithersburg, Maryland, U.S.A.     

Thermodynamic properties of 2,2,4-trimethylpentane

p, V, T data for 2,2,4-trimethylpentane (TMP) have been obtained in the form of volume ratios for six temperatures in the range 278.15 to 338.15 K for pressures up to 280 MPa. Isothermal compressibilities, isobaric expansivities, and internal pressures have been evaluated from the volumetric data. There are strong indications that the combination of the present results with literature data at 348 and 373 K enable accurate extrapolations in the liquid range up to 473 K, and possibly to as low as 170 K, for pressures up to 980 MPa; use of only the present results with the requirement that the B coefficient of the Tait equation should become equal to the negative of the critical pressure at the critical temperature provides interpolations and extrapolations of comparable accuracy. It is suggested that 2,2,4-trimethylpentane is a suitable secondary reference material (because of its large liquid range at atmospheric pressure and the similarity of its volumetric properties to a wide range of fluids) for calibration of measuring cells used for determining volumes of fluids under pressure.     

Thermodynamic and transport properties of 1, 2-dichloroethane

(p, V, T) data for dichloroethane (DCE) have been obtained at 278.15, 288.15, 298.15, 313.15, 323.15, and 338.15 K for pressures either slightly below the freezing pressure or up to a maximum of 280 M Pa, together with densities at 0.1 MPa. A high-pressure self-centering falling-body viscometer method has been used to measure shear viscosities at 278.15, 288.15, 298.15, 313.15, and 323.15 K for pressures either slightly below the freezing pressure or up to a maximum of 330 MPa. Self-diffusion coefficients for DCE are reported at 278.15, 288.15, 298.15, and 313.15 K for maximum pressures up to 300 MPa. Isothermal compressibilities, isobaric expansivities, and internal pressures have been evaluated from the volumetric data. The shear viscosities and self-diffusion coefficients have been interpreted in terms of a modified rough hard-spheres theory. The anomalous behavior observed for p-V-T, shear viscosities, and self diffusion at higher temperatures and pressures is suspected to be the result of temperature and pressure altering the population ratio of the two molecular conformers, trans and gauche.     

Volumetric and Thermodynamic Properties of Liquid Mixtures of 2-n-Butoxyethanol with Water

p–V–T data for six compositions of 2-n-butoxyethanol (BE) and water have been obtained in the form of volume ratios at several temperatures in the range 278.15 to 353.13 K at pressures from atmospheric to 347 MPa or higher. One of the compositions is in the region where two phases exist at certain temperatures, while two compositions are near the boundary of that region. Densities at atmospheric pressure in a temperature range similar to that for the p–V–T data are also reported. Isothermal compressibilities, isobaric expansivities, and changes in the isobaric heat capacity have been calculated from the volumetric data for pressures up to 300 MPa. The values of normalized volume fluctuations obtained from the data at 0.1 MPa approach those of water for conditions which are close to those for phase separation in this system. Such behavior is not observed at 100 MPa, where such separation is suppressed.     

Volumetric measurements under pressure for 2,2,4-trimethylpentane at temperatures up to 353.15 K and for benzene and three of their mixtures at temperatures up to 348.15 K

(p, V, T) data have been obtained in the form of volume ratios relative to 0.1 MPa for benzene (298.15 to 348.15 K), 2,2,4-trimethylpentane (TMP) (313.15 to 353.15 K), and their mixtures near 0.25, 0.5, and 0.75 mole fraction of benzene (313.15 to 348.15 K) for pressures up to near the freezing pressures for benzene and the mixtures, and up to 400 MPa for TMP. Isothermal compressibilitiesκ _T, isobaric expansivitie α, changes in heat capacity at constant pressureΔC _p, and excess molar volumesV ^E have been determined from the data. Literature data at atmospheric pressure have been used to convert theΔC _p toC _p at several temperatures. The isobars for α over the temperature range 278.15 to 353.15 K for TMP intersect near 47 MPa and reverse their order in temperature when plotted against pressure; normalization of the α's by dividing the values at each temperature by the α at 0.1 MPa prevents both the intersection and the reversal of the order. TheV ^E are positive and have an unusual dependence on pressure: they increase with temperature and pressure so that the order of the curves for 0.1, 50, and 100 MPa changes in going from 313.15 to 348.15 K.     

Thermodynamic properties and excess volumes of 2,2,4-trimethylpentane + n-heptane mixtures from 298 to 338 K for pressures up to 400 MPa

(p, V, T) data for mixtures of 2,2,4-trimethylpentane (TMP) and heptane have been obtained in the form of volume ratios for four temperatures in the range 298.15 to 338.15 K for pressures up to 390 MPa. The data have been represented by the Tait equation of state for the purposes of interpolation and extrapolation. The atmospheric pressure densities of both pure components and their mixtures for three temperatures have been measured and used to determine the excess molar volumes. Isothermal compressibilities have been evaluated from the volumetric data.     

Thermodynamic properties of n-hexane

Specific volumes and isobaric heat capacity measurements are reported for n-hexane. The measurements were made in the liquid and vapor phases at temperatures from the triple point and also cover a wide region around the critical point. The thermal, caloric, and acoustic data from our own investigation as well as those of a number of other authors are fitted to a single equation of state with 32 constants. This equation yields to all thermodynamic properties of n-hexane in the temperature range 180 to 630 K and pressures up to 100 MPa. The data in the critical region have been analyzed in terms of a scaled equation of state.     

n-hexane as a model for compressed simple liquids

Isobaric thermal expansivities, _p, ofn-hexane have been measured by pressure-controlled scanning calorimetry from just above the saturation vapor pressure to 40 MPa at temperatures from 303 to 453 K and to 300 MPa at 503 K. These new data are combined with literature data to obtain a correlation equation for _p valid from 240 to 503 K at pressures up to 700 MPa. Correlation equations are developed for the saturated vapor pressure, specific volume, and isobaric heat capacity of liquid n-hexane from 240 to 503 K. Calculated volumes, isobaric and isochoric specific heat capacities. isothermal compressibilities, and thermal coefficients of pressure are presented for the entire range of pressure and temperature. The pressure-temperature behavior of these quantities is discussed as a model behavior for simple liquids without strong intermolecular interactions.     

Thermodynamic properties of n-pentane

Specific volumes and isobaric heat capacity measurements are reported for n-pentane. The measurements were made in the liquid and vapor phases at temperatures ranging from the triple point (173 K) to the onset of dissociation temperature (700 K) and pressures up to 100 MPa including a wide region around the critical point. We are able to fit our data, as well as those of a number of other authors, to a single equation of state with 30 constants. This equation yields the density of n-pentane in the temperature range from 280 to 650 K at pressures up to 80 MPa and the caloric properties up to 500 K. Additional experimental investigations of the thermodynamic properties are required for temperatures above 500 K. Interpolating equations for the caloric properties on the saturated line and in the critical region are also presented.     

p,V, T and derived thermodynamic data for bromobenzene at temperatures from 278 to 323 K and pressures up to 280 MPa

Experimentally determined p, V, T data are reported for bromobenzene at 278, 288, 298, 313, and 323 K, at pressures up to about 280 MPa or (at 278 and 288 K) a lower pressure slightly below the freezing pressure at the temperature of measurement. Values of the isobaric expansivity, isothermal compressibility, internal pressure, and equivalent hard-sphere diameter, derived from the p, V, T data, are presented.On leave from the Department of Chemistry, The University of Auckland, Auckland, New Zealand.     

Thermodynamic properties and vapor pressures of polar fluids from a four-parameter corresponding-states method

A recently proposed extended Lee-Kesler corresponding-states method (ELK) for polar fluids which accurately predicts compressibility factors and departure functions is considered. Tables of polar deviation functions have been generated and values of the shape/size and polar parameters for 52 polar fluids have been calculated, allowing the method to be used for quick hand calculations in addition to the previous, more accurate, computer applications. Additionally, vapor pressures of 44 pure polar fluids were computed using the full version of the ELK and the equality of the Gibbs free energy criterion for phase equilibrium. An ELK vapor pressure correlation is proposed which is essentially numerically equivalent to, but computationally simpler than, the former method. Computed vapor pressures agree with experimental values as well or better than other vapor pressure equations designed exclusively for vapor pressure prediction of polar fluids.     

Isobaric thermal expansivities of binary mixtures ofn-Hexane with 1-hexanol at pressures from 0.1 to 350 MPa and at temperatures from 303 to 503 K

Isobaric thermal expansivities, α_p(p, T), of seven binary mixtures ofn-hexane with l-hexanol (0.0553, 0.1088, 0.2737, 0.2983, 0.4962, 0.6036, and 0.7455 mol fraction of l-hexanol) have been measured with a pressure-controlled scanning calorimeter over the pressure range from just above the saturation pressures to 350 MPa and at temperatures from 302.6 to 503.1 K. The low-temperature isotherms of α_p for particular mixtures observed with respect to the unique crossing point ofn-hexane isotherms reveal an association effect which is reduced when the temperature increases. The high-temperature isotherms of α_p are very similar to the isotherms of puren-hexane, especially for lower mole fractions ofn-hexanol. No known equation of state can reproduce these properties.     

Freezing pressures,p, V,T, and self-diffusion data at 298 and 313 K and pressures up to 300 MPa for 1,3,5-trimethylbenzene

Mesurements are reported for the melting point of 1,3,5-trimethylbenzene at pressures up to 345 MPa. Self-diffusion coefficients and p, V, T data have been obtained at 298 and 313 K for pressures up to 280 MPa. Isothermal compressibilities have been calculated from the p, V, T results. The freezing pressures at 0.1 MPa correspond to previously reported values for modification III of trimethylbenzene. Equivalent hard-sphere diameters estimated from the melting point and p, V, T data are used to apply the rough hard-spheres theory to the self-diffusion data; the calculations indicate that there is random packing of the particles.On leave from Department of Chemistry, University of Auckland, Auckland, New Zealand.     

Thermodynamic Properties of Heavy n-Alkanes in the Liquid State: n-Dodecane

A grid algorithm based on sound speed data, was used to calculate the thermodynamic properties of liquid n-dodecane. The density, isobaric expansion coefficient, isothermal compressibility, isobaric and isochoric heat capacities, enthalpy, and entropy of liquid n-dodecane were calculated in the range of temperatures from 293 to 433 K and pressures from 0.1 to 140 MPa. Coefficients of the Tait equation were determined in the above-identified range of parameters. A table of the thermodynamic properties of n-dodecane is presented.     

Volume ratios for n-pentane in the temperature range 278–338 K and at pressures up to 280 MPa

Volume ratios (V _P/V _0.1), and isothermal compressibilities calculated from them, are reported for n-pentane for seven temperatures in the range 278 to 338 K for pressures up to 280 MPa. The isobaric measurements were made with a bellows volumometer for which a novel technique had to be devised to enable measurements to be made above the normal boiling point (309.3 K). The accuracy of the volume ratios is estimated to be ±0.05 to 0.1% up to 303.15 K and ±0.1 to 0.2% from 313.15 to 338.15 K. The volume ratios are in good agreement with those calculated from recent literature data up to the maximum pressure of the latter, viz., 60 MPa.     

Thermodynamic properties of 1-chloro-1,2,2,2-tetrafluoroethane (R124)

The critical temperature and pressure, vapor pressure, and PVT relations for gaseous and liquid 1-chloro-1,2,2,2-tetrafluoroethane (R124) were determined experimentally. The vapor pressure was measured in the temperature range from 278.15 K to the critical temperature. The PVT measurements were carried out using two types of volumeters in the temperature range from 278.15 to 423.15 K, at pressure up to 100 MPa. The numerical PVT data of gaseous state are fitted as a function of density to a modified Benedict-Webb-Rubin equation. The pressure-volume relations of the liquid at each temperature are correlated satisfactorily as a function of pressure by the Tait equation. The critical density and saturated vapor and liquid densities are also determined and some of the thermodynamic properties are derived from the experimental results.     

Thermodynamic properties of vanadium

This work reviews and discusses the data and information on the various thermodynamic properties of vanadium available through March 1985. These include the heat capacity and enthalpy, enthalpy of melting, vapor pressure, and enthalpy of vaporization. The existing data have been critically evaluated and analyzed, and the recommended values for heat capacity, enthalpy, entropy, and Gibbs energy function covering the temperature range from 1 to 3800 K have been generated. These values are referred to temperatures based on IPTS-1968. The units used for various properties are joules per mole (J · mol^–1). The estimated uncertainties in the heat capacity are ±3% below 15 K, ±10% from 15 to 150 K, ±3% from 150 to 298.15 K, ±2% from 298.15 to 1000 K, ±3% from 1000 to the melting point (2202 K), and ±5% in the liquid region.Paper presented at the Ninth Symposium on Thermophysical Properties, June 24–27, 1985, Boulder, Colorado, U.S.A.