Comparison of potential power production at on‐ and offshore sites

This article presents analyses of the potential power production from turbines located in the near‐shore and offshore environment relative to an onshore location, using half‐hourly average wind speed data from four sites in the Danish wind monitoring network. These measurement sites are located in a relatively high wind speed environment, and data from these sites indicate a high degree of spatial coherence. For these sites and representative turbine specifications (rated power 1·3–2 W) the fraction of time with power output in excess of 500 kW is twice as high for the offshore location as for the land site. Also, the fraction of time with negligible power production (defined as <100 kW output from the turbines described herein) is less than 20% for the offshore site and twice as high at the land‐based location. Capacity factors are higher for coastal sites than for the land site, and the annual capacity factor for the offshore location is twice that of the land site. Potential power output at the offshore site exhibits approximately the same seasonal variation as at the land site but little diurnal variation. Copyright © 2001 John Wiley & Sons, Ltd.     

Wind turbine generator trends for site‐specific tailoring

Turbine optimization for specific wind regimes and climate conditions is becoming more common as the market expands into new territories (offshore, low‐wind regimes) and as technology matures. Tailoring turbines for specific sites by varying rotor diameter, tower height and power electronics may be a viable technique to make wind energy more economic and less intermittent. By better understanding the wind resource trends and evaluating important wind turbine performance parameters such as specific power (ratio of rated power and rotor swept area), developers and operators can optimize plant output and better anticipate operational impacts. This article presents a methodology to evaluate site‐specific wind data for turbine tailoring. Wind characteristics for the Tehachapi wind resource area in California were utilized for this study. These data were used to evaluate the performance of a range of wind turbine configurations. The goal was to analyse the variations in wind power output for the area, assess the changes in these levels with the time of day and season and determine how turbine configuration affects the output. Wind turbine output was compared with California statewide system electrical demand to evaluate the correlation of the wind resource site with local peak demand loads. A comparison of the commercial value of electricity and corresponding wind generation is also presented using a time‐dependent valuation methodology. Copyright © 2005 John Wiley & Sons, Ltd.     

特种风力发电机组塔筒防腐方案研究

高原和海洋的风能资源丰富,更能发挥大容量风力发电机组的优势,利用前景广阔。但高原和海上的自然环境恶劣,对风机承载部件——塔筒的防腐要求更为严格。针对在高原和海上运行的特种风机,分析了塔筒的腐蚀环境,研究了塔筒的防腐原理,提出了塔筒的具体防腐措施和防腐方案,为特种风机塔筒的防腐提供了参考。     

Spatial dependence in wind and optimal wind power allocation: A copula-based analysis

The investment decision on the placement of wind turbines is, neglecting legal formalities, mainly driven by the aim to maximize the expected annual energy production of single turbines. The result is a concentration of wind farms at locations with high average wind speed. While this strategy may be optimal for single investors maximizing their own return on investment, the resulting overall allocation of wind turbines may be unfavorable for energy suppliers and the economy because of large fluctuations in the overall wind power output. This paper investigates to what extent optimal allocation of wind farms in Germany can reduce these fluctuations. We analyze stochastic dependencies of wind speed for a large data set of German on- and offshore weather stations and find that these dependencies turn out to be highly nonlinear but constant over time. Using copula theory we determine the value at risk of energy production for given allocation sets of wind farms and derive optimal allocation plans. We find that the optimized allocation of wind farms may substantially stabilize the overall wind energy supply on daily as well as hourly frequency.     

理论发电量完成率在海上风电场评价中的应用

针对中国目前海上风电场起步较晚,技术不够完善,行业内对于海上风电场建设、机组选型和运营维护缺乏足够经验的特点,为完善海上风电场效能评价体系,提出理论发电量完成率的概念和相应的计算方法;同时,将理论发电量完成率这一指标代入实际案例进行计算分析。结果表明,理论发电量完成率能较好地反映风电机组和风电场的运行状态,能够将风资源状况和风电机组运行状态按照时间序列有机结合起来,是一个可操作性强且具有实际参考价值的指标,对海上风电场的评价和运行管理水平的提升有较好的指导意义。     

Modeling of the dynamics of wind to power conversion including high wind speed behavior

This paper proposes and validates an efficient, generic and computationally simple dynamic model for the conversion of the wind speed at hub height into the electrical power by a wind turbine. This proposed wind turbine model was developed as a first step to simulate wind power time series for power system studies. This paper focuses on describing and validating the single wind turbine model, and is therefore neither describing wind speed modeling nor aggregation of contributions from a whole wind farm or a power system area. The state‐of‐the‐art is to use static power curves for the purpose of power system studies, but the idea of the proposed wind turbine model is to include the main dynamic effects in order to have a better representation of the fluctuations in the output power and of the fast power ramping especially because of high wind speed shutdowns of the wind turbine. The high wind speed shutdowns and restarts are represented as on–off switching rules that govern the output of the wind turbine at extreme wind speed conditions. The model uses the concept of equivalent wind speed, estimated from the single point (hub height) wind speed using a second‐order dynamic filter that is derived from an admittance function. The equivalent wind speed is a representation of the averaging of the wind speeds over the wind turbine rotor plane and is used as input to the static power curve to get the output power. The proposed wind turbine model is validated for the whole operating range using measurements available from the DONG Energy offshore wind farm Horns Rev 2. Copyright © 2015 John Wiley & Sons, Ltd.     

Demonstrating the effect of vertical and directional shear for resource mapping of wind power

The use of wind energy is growing around the world, and its growth is set to continue into the foreseeable future. Estimates of the wind speed and power are helpful to assess the potential of new sites for development and to facilitate electric grid integration studies. In the present paper, wind speed and power resource mapping analyses are performed. These resource mappings are produced on a 13 km, hourly model grid over the entire continental USA for the years of 2006–2014. The effects of the rotor equivalent wind speed (REWS) along with directional shear are investigated. The total dataset (wind speed and power) contains ≈152,000 model grid points, with each location containing ≈78,000 hourly time steps. The resource mapping and dataset are created from analysis fields, which are output from an advanced weather assimilation model. Two different methods were used to estimate the wind speed over the rotor swept area (with rotor diameter of 100 m). First, using a single wind speed at hub height (80 m) and, second, the REWS with directional shear. The demonstration study shows that in most locations the incorporation of the REWS reduces the average available wind power. In addition, the REWS technique estimates more wind power production at night and less production in the day compared with the hub height technique; potentially critical for siting new wind turbines and plants. However, the wind power estimate differences are dependent on seasonality, diurnal cycle and geographic location. More research is warranted into these effects to determine the level at which these features are observed at actual wind plants.© 2015 The Authors. Wind Energy published by John Wiley & Sons, Ltd.     

基于等效风速的风电机组参数对输出功率波动和功率损失特性的影响

以大型三叶风电机组为例,研究发电机组参数对输出功率波动及功率损失的影响.首先建立包括风剪切和塔影效应的等效风速模型,推导输出功率和功率系数的数学模型,研究叶轮半径、塔筒高度、塔筒直径和叶片到塔筒中线的悬垂距离等相关参数对功率波动的频率、幅值、波长、波动区域等特性影响规律.然后建立功率损失的数学模型,研究风电机组参数通过...     

Reliably model of microwind power energy output under real conditions in France suburban area

Micro-wind turbine are now specially designed for rural or urban environment and one of the main advantages of such turbine is that it can be propelled by a wind speed as low as 3 m/s. However, due to terrain roughness in urban environments wind flow is reduced compared to open spaces reducing power output and increasing payback time on capital investment. Well mounting turbines in urban areas may provide the perfect opportunity for onsite generation from wind power. In this paper, we investigate the performance of a micro-wind turbine in a complex urban area and show that due to long time period and very subtile onsite measurements the ideal position for the wind turbine can be determined. Well measured data, wind speed, power output at this particular location are approximated by the Weibull function. The considered model is tested and validated at an urban landscape location in Metz City, France, where an anemometry is positioned at adjacent to the turbine and the instrumentation is positioned specific to its surrounding location and, record wind turbine data thanks to real time wireless communications. Technical data including wind speed and output power were analyzed and reported allowing to provide an reliable estimation of the wind energy potential in an urban location.     

Experimental verification of computational predictions in power generation variation with layout of offshore wind farms

The optimization of wind farms with respect to spatial layout is addressed experimentally. Wake effects within wind turbine farms are well known to be deleterious in terms of power generation and structural loading, which is corroborated in this study. Computational models are the predominant tools in the prediction of turbine‐induced flow fields. However, for wind farms comprising hundreds of turbines, reliability of the obtained numerical data becomes a growing concern with potentially costly consequences. This study pursues a systematic complementary theoretical, experimental and numerical study of variations in generated power with turbine layout of an 80 turbine large wind farm. Wake effects within offshore wind turbine arrays are emulated using porous discs mounted on a flat plate in a wind tunnel. The adopted approach to reproduce experimentally individual turbine wake characteristics is presented, and drag measurements are argued to correctly capture the variation in power generation with turbine layout. Experimental data are juxtaposed with power predictions using ANSYS WindModeller simulation suite. Although comparison with available wind farm power output data has been limited, it is demonstrated nonetheless that this approach has potential for the validation of numerical models of power loss due to wake effects or even to make a direct physical prediction. The approach has even indicated useful data for the improvement of the physics within numerical models. Copyright © 2014 John Wiley & Sons, Ltd.     

Survey of wind farm control—power and fatigue optimization

The main goal of this paper is to establish the present state of the art for wind farm control. The control area that will be focused on is the mechanical/aerodynamic part, which includes the wind turbines, their power production, fatigue and wakes affecting neighbouring wind turbines. The sub‐objectives in this area of research are as follows: (i) maximizing the total wind farm power production; (ii) following a reference for the total wind farm active power; and (iii) doing this in a manner that minimizes fatigue loading for the wind turbines in the farm. Each of these sub‐objectives is discussed, including the following important control issues: choice of input and output, control method and modelling used for controller design and simulation. The available literature from industry is also considered. Finally, a conclusion is presented discussing the established results, open challenges and necessary research. Copyright © 2014 John Wiley & Sons, Ltd.     

A study of the performance benefits of closely-spaced lateral wind farm configurations

Scaled wind turbine experiments were conducted in order to evaluate the beneficial effect of closely-spaced lateral wind turbine configurations on the performance of a wind farm. Two outer wind turbines were spaced apart with a particular gap distance and the longitudinal setback of a central rotor was varied at each gap width. The turbine placement resulted in tip-to-tip separation distances that ranged from 1 diameter (D) to 0.25D. Additionally, the performance of a wind farm layout in rough and smooth boundary layers, designed to mimic onshore and offshore conditions, respectively, was evaluated. It was observed that a narrow gap between several laterally-aligned rotors creates an in-field blockage effect that results in beneficial flow acceleration through the gap. This increase in speed increases the power output of the central turbine when its longitudinal setback is between 0D and 2.5D. A cumulative increase in power output of 17% was observed when 3 rotors were aligned in a lateral plane with a blade tip separation of 0.5D or 0.25D, compared to the same number of rotors in isolation. While the benefits of closely-spaced wind turbines were observed in both of the tested boundary layers, the performance benefits with a smooth boundary layer were smaller than with a rough boundary layer. These results may lead to new wind farm design methodologies for certain topology- and wind distribution-specific sites and suggest that wind turbines can be closely-spaced in the lateral direction in order to obtain substantial increases in power.     

Utility scale wind turbines on a grid-connected island: A feasibility study

This paper analyzes the technical and economic feasibility of installing utility-scale wind turbines on the Fox Islands, located 12 miles from the coast of Maine in the United States. Three locations on the islands, as well as a near offshore site, are analyzed in detail as potential sites for wind turbine installations. As discussed in this work, the logistic problems of transporting and installing wind turbines on the island require innovative solutions. These include locally available amphibious vessels, which can land turbine components at suitable shallow spots on the island, self-erecting towers, which allow use of a smaller crane for installation, and a special turbine foundation suitable for the local ground conditions. In the economic analysis, in addition to standard life-cycle parameters, renewable energy credits (REC) were also included. This work concludes that the installation of sub-megawatt wind turbines on the island is logistically possible and will lead to a reduction in the cost of electricity to the customers.     

Profiling the regional wind power fluctuation in China

As China starts to build 6 10-GW wind zones in 5 provinces by 2020, accommodating the wind electricity generated from these large wind zones will be a great challenge for the regional grids. Inadequate wind observing data hinders profiling the wind power fluctuations at the regional grid level. This paper proposed a method to assess the seasonal and diurnal wind power patterns based on the wind speed data from the NASA GEOS-5 DAS system, which provides data to the study of climate processes including the long-term estimates of meteorological quantities. The wind power fluctuations for the 6 largest wind zones in China are presented with both the capacity factor and the megawatt wind power output. The measured hourly wind output in a regional grid is compared to the calculating result to test the analyzing model. To investigate the offsetting effect of dispersed wind farms over large regions, the regional correlations of hourly wind power fluctuations are calculated. The result illustrates the different offsetting effects of minute and hourly fluctuations.     

Numerical study of a concept for major repair and replacement of offshore wind turbine blades

Repair and replacement of offshore wind turbine blades are necessary for current and future offshore wind turbines. To date, repair activities are often conducted using huge jack‐up crane vessels and by applying a reverse installation procedure. Because of the high costs associated with installation and removal of offshore wind turbine components and the low profit margin of the offshore wind industry, alternative methods for installation and removal are needed. This paper introduces a novel concept for replacement or installation of offshore wind turbine blades. The concept involves a medium‐sized jack‐up crane vessel and a tower climbing mechanism. This mechanism provides a stable platform for clamping, lowering, and lifting of a blade. A case study of a 5‐MW offshore wind turbine is shown, where common engineering practices were applied and numerical simulations of the marine operations were carried out using finite element and multibody simulation tools. Operational limits for wave and wind actions were established to demonstrate the technical feasibility of the proposed concept.     

Comparative assessment of performance of foreign and local wind turbine manufacturers in China

Compared to the conventional fossil fuel energy, wind power provides clean energy which can mitigate the impacts of greenhouse gas emission and optimize the electric power source structure. During the last decade, the strong support of the Chinese government has contributed to the rapid development of the Chinese wind power sector which has in turn resulted in a significant growth of the Chinese wind turbine manufacturing industry. This growth went through several phases including the initial approval of several leading global Wind Turbine Manufacturers (WTMs) to enter the Chinese market through various methods which included the establishment of wholly foreign-owned enterprises from 2005. Similarly, several government policies have contributed to the significant expansion in terms of both productivity and quantities by local Chinese WTMs. The entrance of foreign WTMs into the Chinese market coupled with the rapid growth of local WTMs has contributed to intense competition in China’s wind turbine manufacture market. This paper analyzes the characteristics of the wind turbine manufacturing industry in China and establishes a hierarchical structure of the WTMs’ competitive priority system. This system consists of 5 indicators and 10 sub-indicators. By comparing the different performances of each indicator, the competitive advantages and disadvantages of the foreign and local WTMs in the Chinese market are identified. The findings provide a valuable reference for the WTMs to improve their competitive priorities and to formulate their competitive strategy in the Chinese wind turbine market. This paper provides inputs for the sustainable development of wind power industry in other countries.     

海上风电场功率提升和疲劳平衡综合优化控制

针对海上风电场,综合功率提升和疲劳平衡分配的优化目标,提出一种以天为优化周期的优化策略。在电网高负荷时段,基于Jensen尾流模型,以轴向诱导因子为优化变量,风电场整场功率最大为目标,运用随机粒子群算法进行风功率利用提升优化控制;在电网低负荷时段,基于风电机组综合疲劳系数计算方法,以机组轴向诱导因子为优化变量,应用尾流计算模型调整轴向诱导因子来满足电网限功率指令,以机组疲劳系数标准差最小为目标,采用粒子群算法寻优进行疲劳平衡优化。以某海上风电场进行算例分析,结果表明该优化策略在一天的优化周期内可较好地实现风电场功率提升和疲劳平衡的综合优化。     

Sensitivity of southern California wind energy to turbine characteristics

Using output from a high‐resolution meteorological simulation, we evaluate the sensitivity of southern California wind energy generation to variations in key characteristics of current wind turbines. These characteristics include hub height, rotor diameter and rated power, and depend on turbine make and model. They shape the turbine's power curve and thus have large implications for the energy generation capacity of wind farms. For each characteristic, we find complex and substantial geographical variations in the sensitivity of energy generation. However, the sensitivity associated with each characteristic can be predicted by a single corresponding climate statistic, greatly simplifying understanding of the relationship between climate and turbine optimization for energy production. In the case of the sensitivity to rotor diameter, the change in energy output per unit change in rotor diameter at any location is directly proportional to the weighted average wind speed between the cut‐in speed and the rated speed. The sensitivity to rated power variations is likewise captured by the percent of the wind speed distribution between the turbines rated and cut‐out speeds. Finally, the sensitivity to hub height is proportional to lower atmospheric wind shear. Using a wind turbine component cost model, we also evaluate energy output increase per dollar investment in each turbine characteristic. We find that rotor diameter increases typically provide a much larger wind energy boost per dollar invested, although there are some zones where investment in the other two characteristics is competitive. Our study underscores the need for joint analysis of regional climate, turbine engineering and economic modeling to optimize wind energy production. Copyright © 2012 John Wiley & Sons, Ltd.     

Validation of the dynamic wake meander model for loads and power production in the Egmond aan Zee wind farm

This paper investigates wake effects on load and power production by using the dynamic wake meander (DWM) model implemented in the aeroelastic code HAWC2. The instationary wind farm flow characteristics are modeled by treating the wind turbine wakes as passive tracers transported downstream using a meandering process driven by the low frequent cross‐wind turbulence components. The model complex is validated by comparing simulated and measured loads for the Dutch Egmond aan Zee wind farm consisting of 36 Vestas V90 turbine located outside the coast of the Netherlands. Loads and production are compared for two distinct wind directions—a free wind situation from the dominating southwest and a full wake situation from northwest, where the observed turbine is operating in wake from five turbines in a row with 7D spacing. The measurements have a very high quality, allowing for detailed comparison of both fatigue and min–mean–max loads for blade root flap, tower yaw and tower bottom bending moments, respectively. Since the observed turbine is located deep inside a row of turbines, a new method on how to handle multiple wakes interaction is proposed. The agreement between measurements and simulations is excellent regarding power production in both free and wake sector, and a very good agreement is seen for the load comparisons too. This enables the conclusion that wake meandering, caused by large scale ambient turbulence, is indeed an important contribution to wake loading in wind farms. Copyright © 2012 John Wiley & Sons, Ltd.     

New high profitable wind turbines

To generate more quantities of electric energy from wind it is necessary to use a new type of wind turbine built in the regulable mantle's nozzle. This wind turbine type replaces the free air stream from wind by a programmed, i.e. regulated, and partially concentrated stream of air. The nozzle shell is designed as an aerodynamically shaped ring with wings with its lower pressure side pointed towards the centre so that the lift force on each part of the wing is directed radially towards the centre. This induces centrifugal reaction force in the airflow that causes the stream field to expand strongly downstream of the rotor and includes a greater number of streamlines in the active stream in front of the rotor (upstream). Thus the nozzle forces a higher mass flow rate of air through the turbine. The higher mass flow and higher velocity reduction behind the rotor result in a higher energy output from the wind turbine in the nozzle. In this way the wind turbine efficiency is multiplied. New turbines induce more power from weaker and medium winds and their lasting time, because of the relation P=f(v³) (i.e. the power corresponds to wind velocity raised to third power). Wind turbine nozzle produces three times more energy than conventional wind turbine. Short economic analysis for conditions of the island of Lastovo indicates that profit gained by new turbines is up to five times higher than by conventional turbines. The new wind turbine nozzle should generate interest and demand on an international market, even for regions with weaker winds.