Inactivation of Escherichia Coli Using Remote Low Temperature Glow Discharge Plasma

Low-temperature plasma is distinguished as a developing approach for sterilization which can deal with and overcome those problems such as thermal sensitivity and destruction by heat, formation of toxic by-products, higher costs and inefficiency in performances, caused by conventional methods. In this study, an experimental investigation was undertaken to characterize the effects of the operational parameters, such as treating time, discharge power and gas flow rate, of remote glow discharge air plasma. The results show that the inactivation of Escherichia coli can reach above 99.99% in less than 60 seconds and the optimal operational conditions for treating time, discharge power and gas flow rate were： 40 s, 80 W and 60 cm^3/min, respectively. The contribution of UV radiation during plasma germ deactivation is very limited.     

A Study of Multi-Permeating TiN/Ti Alloying Layer Using Plasma Surface Alloying Technology

TiN/Ti multi-permeating alloying layer has been formed on the low carbon steel by means of the double glow-discharge plasma surface alloying technique and hollow-cathode effect. The alloying layer was detected by axiovert 25 CA optical microscope with computer analyzing software （LEC）, GDA-2 glow discharge spectroscopy （GDS）, X-ray diffraction （XRD） and galvanochemical method. The results showed that the thickness of TiN/Ti multi-permeating alloying layer was about 10μm, the content of Ti on the surface was up to 63.48 wt% and the content of N was up to 12.46 wt%. The atom Ti and N concentrations changed gradually across the depth of the alloying layer and the preferred orientation of TiN/Ti alloying layer was crystal surface （200）. The multi-permeating alloying layer and substrate were combined through metallurgy. The surface appearances of the multi-permeating alloying layer were uniform and of a compact cellular structure. The hardness of the surface was about 1600-3000 HV0.1. The corrosion resistance of the permeating TiN/Ti alloying layer in 0.5 mol/L H2SO4 solution was greatly increased and the corrosion rate was only 0.3082 g/m^2. h.     

RC-Coupled Atmospheric Glow Discharge in Air

Resistance and capacity-coupled glow discharge （RCCGD） is a new method to produce atmospheric pressure glow discharge in air. In RCCGD, each electrode is connected with both a resistor R and a capacitor C. The R and C can provide a negative feedback to prevent the transition from glow to spark discharge. The influence of coupled resistance, coupled capacity, inter-electrode gap and power source frequency on the discharge is studied and discussed.     

Study on Glow Discharge Plasma Used in Polyester Surface Modification

To achieve an atmospheric pressure glow discharge(APGD)in air and modify the surface of polyester thread using plasma,the electric field distribution and discharge characteristics under different conditions were studied.We found that the region with a strong electric field,which was formed in a tiny gap between two electrodes constituting a line-line contact electrode structure,provided the initial electron for the entire discharge process.Thus,the discharge voltage was reduced.The dielectric barrier of the line-line contact electrodes can inhibit the generation of secondary electrons.Thus,the transient current pulse discharge was reduced significantly,and an APGD in air was achieved.We designed double layer line-line contact electrodes,which can generate the APGD on the surface of a material under treatment directly.A noticeable change in the surface morphology of polyester fiber was visualized with the aid of a scanning electron microscope(SEM).Two electrode structures–the multi-row line-line and double-helix line-line contact electrodes–were designed.A large area of the APGD plasma with flat and curved surfaces can be formed in air using these contact electrodes.This can improve the efficiency of surface treatment and is significant for the application of the APGD plasma in industries.     

Application of the Multi-Electrode in the Degradation of Alizarin Red Induced by Glow Discharge Plasma

This paper presents a novel set-up to be used in the degradation of dye, Various influencing factors, such as the voltage, the number of the anodes, and the catalytic action of Fe^2＋, were examined. Chemical oxygen demand （COD）, ultraviolet （UV）, FTIR absorption spectra, and atomic force microscopy （AFM） were used to monitor the degradation process. The results showed that the efficiency of degradation is raised by increasing the applied voltage, and is further improved when two or three anodes are used. Moreover, the use of Fe^2＋ ion can promote the degradation reaction and shorten the degradation time. So the multi-electrode instrument is more efficient in degrading the dye and should be further studied.     

Study of Atmospheric Pressure Abnormal Glow Discharge

Atmospheric pressure abnormal glow discharge （APAGD） was carried out simply with a transformer of 1 ： 500 driven by a alternating current with a frequency of 50 Hz. Typical stable discharge parameters, namely voltage of 400 V to 850 V and current of 60 mA to 110 mA were measured by oscillograph. Simulation of the discharge process suggested that the stable discharge was supported by the impedance from the secondary coil of the transformer, which offered a negative feedback to prevent the discharge from turning into an arc. An interpretation was given for the oscillogram of the sinuous discharge current and square voltage. Furthermore, the electron temperature and electron density averaged in the discharge channel of APAGD were estimated.     

Transition from Spark Discharge to Constricted Glow Discharge in Atmospheric Air by Capacitor Coupled Discharge

The transition from a spark discharge to a constricted glow discharge in atmospheric air was studied with a capacitor coupled pin-to-water plasma reactor. The reason of the transition is considered to be of various factors, namely the change of the air gap due to the polarization of water molecules by the electric field, the feedback effect of the capacitors, and the ion trapping mechanism. The effects of the frequency of the power supply, inter-electrode gap, and coupled capacitance on the discharge transition were also investigated.     

Degradation of Anionic Dye Eosin by Glow Discharge Electrolysis Plasma

This paper describes a novel method for the degradation of eosin by using glow discharge electrolysis （GDE）. The effects of various parameters on the removal efficiency were studied. It was found that the eosin degradation could be raised considerably by increasing the applied voltage and the initial concentration, or by decreasing pH of the aqueous solution. Fe^2＋ ion had an evident accelerating effect on the eosin degradation. The degradation process of eosin obeyed a pseudo-first-order reaction. The relationship between the degradation rate constant k and the reaction temperature T could be expressed by Arrhenius equation with which the apparent activation energy Ea of 14.110 kJ· mol^-1 and the pre-exponential factor k0 of 2.065× 10^-1 min^-1 were obtained, too. The determination of hydroxyl radical was carried out by using N, N-dimethyl -p-nitrosoaniline （RNO） as a scavenger. The results showed that the hydroxyl radical plays an important role in the degradation process.     

Low Pressure DC Glow Discharge Air Plasma Surface Treatment of Polyethylene (PE) Film for Improvement of Adhesive Properties

The present work deals with the change in surface properties of polyethylene (PE) film using DC low pressure glow discharge air plasma and makes it useful for technical applications. The change in hydrophilicity of the modified PE film surface was investigated by measuring contact angle and surface energy as a function of exposure time. Changes in the morphological and chemical composition of PE films were analyzed by atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). The improvement in adhesion was studied by measuring T-peel and lap-shear strength. The results show that the wettability and surface energy of the PE film has been improved due to the introduction of oxygen-containing polar groups and an increase in surface roughness. The XPS result clearly shows the increase in concentration of oxygen content and the formation of polar groups on the polymer surface. The AFM observation on PE film shows that the roughness of the surface increased due to plasma treatment. The above morphological and chemical changes enhanced the adhesive properties of the PE film surfaces, which was confirmed by T-peel and lap-shear tests.     

Experimental Study on the Interaction of Electromagnetic Waves and Glow Plasma

An experimental system was established in order to study the interaction between electromagnetic waves, with a frequency of 300 kHz to 3 GHz, and DC glow discharge plasma. The results show that the DC glow discharge plasma affects the transmission properties of electromagnetic waves, while the waves can change both temperature and density of electrons.     

Degradation of Methyl Orange in Water by Contact Glow Discharge Electrolysis

The degradation of methyl orange in a neutral phosphate buffer solution was investigated by means of contact glow discharge electrolysis （CGDE）. The methyl oranges were degraded and eventually decomposed into inorganic carbon when CGDE was conducted under the applied DC voltage of 480 V and current of ca. 80 mA. As the intermediate products, some phenolic compounds were detected as well as carboxylic acids. Experimental results showed that the oxidation process followed the first-order reaction law. Based on the analysis of the ultraviolet （UV） spectra of the solution and the intermediate products from High Pressure Liquid Chromatography-Mass Spectrum （HPLC-MS）, the reaction pathway was proposed. The attack of hydroxyl radicals was considered to be a key step to start the whole oxidation process.     

Self-Consistent Model for Pulsed Direct-Current N2 Glow Discharge

A self-consistent analysis of a pulsed direct-current (DC) N2 glow discharge is presented. The model is based on a numerical solution of the continuity equations for electron and ions coupled with Poisson‘s equation. The spatial-temporal variations of ionic and electronic densities and electric field are obtained. The electric field structure exhibits all the characteristic regions of a typical glow discharge (the cathode fall, the negative glow, and the positive column). Current-voltage characteristics of the discharge can be obtained from the model. The calculated current-voltage results using a constant secondary electron emission coefficient for the gas pressure 133.32 Pa are in reasonable agreement with experiment.     

Characterization of Nitrogen Glow Discharge Plasma via Optical Emission Spectrum Simulation

Optical emission spectroscopy in nitrogen glow discharge plasma is simulated, and the collision excitations and characteristic emissions of the species （N2, N2^＋, N^＋, N） are investigated by a Monte Carlo model for nitrogen molecular gas discharge. The excitation rates of the main excited states are calculated and the corresponding relation and relative magnitude between the distribution of excitation rate of a certain excited state and the distributions of the emission rates of various lines originating from this excited level are also explored. The simulated results are compared with the experimental measurements in two typical discharge conditions. The luminescence mechanism of the line N2^＋： 391.4 nm is explained based on the microscopic plasma processes. The cathode glow in N2 discharge is found to be mainly caused by N^＋ impact excitation and the intensity of cathode glow decreases with the voltage. The corresponding relation between the emission rate or intensity of the 391.4 nm line and the production rate and the density of N2^＋ is also examined.     

Excited Electron Temperature and Molecular Vibration Temperature During Transition from Filamentary Discharge to Glow Discharge in Surface Discharge in Air

A dielectric barrier surface discharge device was used to investigate the transition from a filamentary discharge to a glow discharge in air at different gas pressures. Discharge images and waveforms of the applied voltage and discharge current were recorded simultaneously, and it was found that the discharge could transit from filamentary to glow with the decrease in pressure. Optical emission spectra during the transition from a filamentary discharge to a glow one were recorded. Excited electron temperature can be determined from the ratios of the relative intensities of spectral lines while molecular vibration temperature can be measured by analysing spectral lines of the N2 second positive band system. The results show that both the excited temperature and molecular vibration temperature increase with the decrease in the gas pressure. Qualitative explanations are given.     

Oxidative Degradation of 4-chlorophenol in Aqueous Induced by Plasma with Submersed Glow Discharge Electrolysis

The oxidative degradation of 4-chlorophenol （4-CP） in aqueous solution induced by plasma with submersed glow discharge has been investigated. The concentration of 4-CP and the reaction intermediates were determined by high performance liquid chromatography （HPLC）. Various influencing factors such as the initial pH, the concentration of 4-CP and the catalytic action of Fe^2＋ were examined. The results indicate that 4-CP is eventually degraded into inorganic ion, dioxide carbon and water. The attack of hydroxyl radicals on the benzene rings of 4-CP in the initial stage of oxidative reactions is presumed to be a key step. They also suggest that the reaction is of a pseudo-first order kinetic reaction and the proposed method is an efficient way for the 4-CP degradation,     

Surface Treatment of Polyethylene Terephthalate Film Using Atmospheric Pressure Glow Discharge in Air

Non-thermal plasmas under atmospheric pressure are of great interest in polymer surface processing because of their convenience, effectiveness and low cost. In this paper, the treatment of Polyethylene terephthalate (PET) film surface for improving hydrophilicity using the non-thermal plasma generated by atmospheric pressure glow discharge (APGD) in air is conducted. The discharge characteristics of APGD are shown by measurement of their electrical discharge parameters and observation of light-emission phenomena, and the surface properties of PET before and after the APGD treatment are studied using contact angle measurement, x-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). It is found that the APGD is homogeneous and stable in the whole gas gap, which differs from the commonly filamentary dielectric barrier discharge (DBD). A short time (several seconds) APGD treatment can modify the surface characteristics of PET film markedly and uniformly. After 10 s APGD treatment, the     

Degradation of Chloroanilines in Aqueous Solution by Contact Glow Discharge Electrolysis

Contact glow discharge electrolysis of some chloroanilines in sodium sulfate was investigated in different initial concentrations.Each of them underwent the dechlorination,deamination theough oxidative degradation,and were eventually decomposed into hydrogen carbonate and carbon dioxide.It was testifies that the chlorine atomn and amidogen could be transformed into chloride ion and nitrite ion ,respectively.Fe^2 has a remarkable catalytic effect on the degradation of them.On the basis of the detailed analysis of the intermediate products and kinetic hehaviors,the reaction pathway was proposed,in which the attack of hydroxyl radical on the benzene ring of starting material might be a key step.     

Synthesis of Poly （Butyl Methacrylate/Butyl Acrylate） Highly Absorptive Resin Using Glow Discharge Electrolysis

A highly absorptive resin poly （butyl methacrylate （BMA）-co-butyl acrylate （BA）） was prepared by emulsion polymerization, which was initiated by glow discharge electrolysis plasma （GDEP）. The effects of discharge voltage, discharge time, monomer ratio and the amounts of cross- linking agent were examined and discussed in detaiI. The chemical structure of the obtained resin was characterized by means of attenuated total reflectance Fourier transform infrared spectroscopy, thermogravimetric analysis, and scanning electron microscopy. The optimal conditions were ob- tained as： discharge voltage was 600 V, discharge time was 8 min, the ratios of BMA：BA being 2：1 for chloroform and 3：1 for xylene, with 2% N, N＇-methylenebis. Under optimal conditions, the oil absorbency was 70 g/g for chloroform and 46 g/g for xylene. Moreover, the absorptive dynamical behavior of the resulting resin was also investigated.     

Best Magnetic Condition to Generate Hollow Cathode Glow Plasma in High Vacuum简

Based on magnetron hollow cathode discharge, the magnetic condition of glow plasma generation in high vacuum, including both direction and magnitude of the applied mag- netic field, is theoretically derived and experimentally evaluated in this paper. Single particle orbital theory is introduced to discuss the possibilities to generate glow plasma at gas pressure under 10-2 Pa when the magnetic field direction is parallel or perpendicular or oblique to the electric field direction. A quantitative estimation criterion of magnetic induction intensity is also proposed in theory. The comparison with experiments suggests that glow plasma in high vacuum will form more easily in oblique magnetic field condition and that the criterion is accurate enough to estimate magnetic induction intensity at a certain gas pressure.     

316L不锈钢表面双层辉光离子渗金属技术制备Cr2O3涂层

为改善不锈钢的阻氚渗透性能,采用双层辉光离子渗金属技术在316L不锈钢表面渗铬渗氧制备出了氧化铬涂层,对涂层的组织特征、相组成和合金元素成分分布及渗入机理进行了分析.结果表明,渗铬后表面主要形成Cr的沉积层和Cr在α-Fe中的固溶体相,渗层厚度可达21 μm,铬含量最高可达92%,且由表及里呈梯度分布;随后对渗铬层进行渗氧处理,表面形成以Cr2O3为主的陶瓷层,其有效厚度约为45 μm,渗层与基体结合牢固.