Single-stage electronic ballast with high-power factor

This article proposes a single-stage electronic ballast circuit with high-power factor. The proposed circuit was derived by sharing the switches of the power factor correction (PFC) and the half-bridge LCC resonant inverter. This integration of switches forms the proposed single-stage electronic ballast, which provides an almost unity power factor and a ripple-free input current by using a coupled inductor without increasing the voltage stress. In addition, it realises zero-voltage-switching (ZVS) by employing the self-oscillation technique. The saturable transformer constituting the self-oscillating drive limits the lamp current and dominates the switching frequency of the ballast. Therefore, the proposed single-stage ballast has the advantage of high-power factor, high efficiency, low cost and high reliability. Steady-state analysis of the PFC and the half-bridge LCC resonant inverter are described. The results of experiments performed using a 30 W fluorescent lamp are also presented to confirm the performance of the proposed ballast.     

Single-stage line-coupled ac/dc converter with high power factor and ripple-free input current

Single-stage line-coupled ac/dc converter with high power factor and ripple-free input current is proposed. The proposed power factor correction circuit can achieve high power factor and ripple-free input current using a coupled inductor. Experimental results for a 400?W converter at a constant switching frequency of 100?kHz are obtained to show the performance of the proposed converter.     

An improved charge pump power factor correction electronic ballast

An improved charge pump power factor correction (CPPFC) electronic ballast using the charge pump concept is proposed in this paper. Circuit derivation, principle of operation, and the conditions for achieving unity power factor are discussed. The proposed electronic ballast is implemented and tested with two 40 W fluorescent lamps. It is shown that 84% of overall efficiency and 1.6 of crest factor can be achieved with 200-V line input voltage. The measured line input current harmonics satisfy IEC 1000-3-2 Class C requirements. The lamp power variation range is automatically limited within ±15% for ±10% line input voltage variation without feedback control     

High frequency electronic ballast provides line frequency lampcurrent

Most electronic ballasts for fluorescent lamps provide a sinusoidal lamp current at the switching frequency. The high-frequency current flowing through the lamp can generate significant radiated noise, which is unacceptable in noise-sensitive applications, such as fluorescent lights in airplanes. Using shielded enclosures for the lamps may solve the problem, but it is expensive. A discontinuous conduction mode (DCM) electronic ballast topology is presented which drives the lamp with line frequency current, just like a magnetic ballast. However, compared to a magnetic ballast, its weight is substantially reduced due to operation at 40 kHz switching frequency. The topology also ensures unity power factor at the input and stable lamp operation at the output     

New charge pump power-factor-correction electronic ballast with awide range of line input voltage

A new charge pump power-factor-correction (CPPFC) electronic ballast with a wide range of line input voltage is proposed in this paper. Circuit derivation and DC-bus voltage stress at start-up mode are discussed. The average lamp current control with switching frequency modulation is developed to achieve constant lamp power operation and low-crest factor. The proposed CPPFC electronic ballast is analyzed, implemented, and evaluated. It features continuous line input current, low total harmonic distortion (THD), constant lamp power operation, low-crest factor, and less switching current stress with low-DC-bus voltage stress for the line voltages from 180 to 265 V     

Charge pump power-factor-correction dimming electronic ballast

A voltage-source charge pump power-factor correction (CPPFC) continuous dimming electronic ballast is proposed in this paper. The basic charge pump PFC principle is presented, and its unity power factor condition is then reviewed. Constant lamp power control and crest factor correction technique in dimming mode operation are then discussed. A continuous dimming controller with average lamp current control and duty-cycle modulation is developed so that the lamp is able to operate in constant power and low crest factor from 20% to 100% dimming level. The developed dimming electronic ballast has features of higher than 0.99 power factor, low crest factor, and low-DC-bus voltage     

Investigation of a New Control Strategy for Electronic Ballasts Based on Variable Inductor

In this paper, a new control method for electronic ballasts based on the use of a variable inductor is presented. The main goal is to perform the complete control of the electronic ballast by maintaining the switching frequency constant and without using other parameters of the power converter, such as input voltage or duty cycle. The magnetic regulator is controlled by means of a dc current, which allows performing both lamp soft starting and lamp dimming. Apart from the important advantage of keeping a constant frequency during full electronic ballast operation, the proposed method presents additional advantages when compared to other control methods, such as inherent isolated control, more linear control characteristics, constant electrode power, and higher efficiency. Experimental results from a 36-W linear fluorescent lamp prototype are presented.     

A Novel Constant Power Control Circuit for HID Electronic Ballast

This paper presents a constant power control circuit for a three-stage high-intensity discharge (HID) electronic ballast. The three-stage electronic ballast is composed of a boost pre-regulator to achieve a high power factor, a DC/DC buck converter to regulate lamp current with constant lamp power, and a full-bridge inverter to drive the HID lamp with a low-frequency ac squarewave current. The buck converter operating in current mode utilizes current sense level-shift technique to achieve constant power output. The proposed constant power control circuit is easily designed and implemented for the three-stage HID electronic ballast. Finally, a laboratory prototype of a 70 W HID electronic ballast is implemented. The measured results show that the proposed ballast can be applied for various HID lamps with low lamp power variation (less than 0.6%).     

Analysis of a ripple-free input-current boost converter withdiscontinuous conduction characteristics

Coupled inductor techniques supply a method to reduce the power converter size and weight and achieve ripple-free current. The boost power converter is a very popular topology in industry. However, the input-current ripple hinders efforts to meet electromagnetic interference (EMI) requirements. In particular, the input current becomes discontinuous and pulsating when the conventional boost power converter operates in the discontinuous inductor-current mode. This paper describes a boost power converter which has the same discontinuous properties as the conventional boost power converter. However, the proposed boost topology has continuous or ripple-free input current when it operates with discontinuous inductor-current. The proposed topology is compared with traditional converter topologies, such as the Sepic and Cuk power converters. Simulation results are presented. The prototype is built to demonstrate the theoretical prediction. The proposed boost topology is simple, with straightforward control [the same as pulse-width modulation (PWM)]     

A single-stage electronic ballast with high power factor

A single stage electronic ballast with high power factor (HPF) is proposed in this letter. The single-phase boost-type rectifier provides HPF. A saturable transformer constituting the self-oscillating drive limits the lamp current and dominates the switching frequency of the ballast. Experimental results obtained on a 40 W fluorescent lamp are discussed     

Improving crest factor of electronic ballast-fed fluorescent lampcurrent using pulse frequency modulation

In case where electronic ballast employing a valley-fill passive power-factor correction (PFC) circuit is used for feeding fluorescent tamps, a new method to reduce crest factor of the lamp current is studied in this paper. It is known that a 50% valley-fill passive PFC provided for high input power factor results in undesirable value of crest factor of the fluorescent lamp current, In order to reduce crest factor to a lower value, a pulse frequency modulation technique based on the waveform of the DC-link voltage which is predetermined by the passive PFC circuit is taken into the switching control action of the electronic ballast. An equation-based analysis between the crest factor of lamp current and the effect of varying the inverter switching frequency is comprehensively performed. Several simulation and experiment results illustrate the Effectiveness of the proposed control scheme     

Acoustic-resonance-free electronic ballast for automotive HID lamps

A novel cost-effective and acoustic-resonance-free electronic ballast used to drive automotive high intensity discharging (HID) lamps that utilise a constant lamp power control scheme is proposed. The presented ballast is comprised of a buck-boost flyback converter to provide negative DC voltages and a half-bridge-type inverter to supply the lamp with low-frequency, square-wave AC voltage/ current. Owing to its low-frequency operation, no acoustic resonance occurs on the automotive HID lamps. Design guidelines and experimental results are demonstrated for a 35 Wautomotive HID lamp prototype ballast operating at 400 Hz switching frequency with battery input DC voltage of 12 V.     

基于IR2155 的高压钠灯电子镇流器设计

本文针对高压钠灯电子镇流器设计中，开关损耗大、驱动复杂、启动速度慢等问题，提出一种高性能高压钠灯用电子镇流器电路。该电路成功的应用了L6560校正芯片和IR2155专用半桥驱动芯片，即简化了传统的驱动电路，又实现了变频调节，提高了启动速度，保证了灯功率的稳定。通过频率和辅助元件的设置，半桥逆变电路可工作在软开关状态。同时设计出可靠的、能产生3．5kV电压的启动电路，保证灯在热灯熄灭时，切断触发脉冲，而后自动恢复启动状态。实验结果表明该镇流器性能优良，功率因数大于0．99，启动时间小于2.4min。     

Single-stage electronic ballast with dimming feature and unitypower factor

Analysis, design, and practical consideration of a single-stage electronic ballast with dimming feature and unity power factor are presented in this paper. The proposed single-stage ballast is the combination of a boost converter and a half-bridge series-resonant parallel-loaded inverter. The boost semistage working in the discontinuous conduction mode functions as a power factor corrector and the inverter semistage operated above resonance are employed to ballast the lamp. Replacing the lamp with the plasma model, analysis of the ballast is fulfilled. The dimming feature is carried out by pulse-width modulation (PWM) and variable-frequency controls simultaneously. The proposed single-stage ballast is suitable for applications with moderate power level and low-line voltage while requiring a high-output voltage. It can save a controller, an active switch and its driver, reduce size, and possibly increase system reliability while requiring two additional diodes over a conventional two-stage system. A prototype was implemented to verify the theoretical discussion. The hardware measurements have shown that the desired performance can be achieved feasibly     

Small-signal analysis of a low-cost power control for LCC series-parallel inverters with resonant current mode control for HID lamps

In this paper, a low-cost power control for LCC series-parallel inverters with resonant current mode control for high intensity discharge (HID) lamps is presented. These resonant inverters require controlling the power supplied to the lamp in order to avoid exceeding the maximum lamp power recommended by the lamp manufacturer. The classical control method measures the lamp voltage and current and they are multiplied analogically, obtaining the lamp power consumption measure. This control circuitry results very complex due to the lamp voltage and current wide variations range during ignition and discharge processes. Assuming a regulated input dc voltage (bus voltage) provided by the power factor correction (PFC) pre-regulator and an inverter constant efficiency along the lamp aging, the lamp power consumption may be estimated and regulated properly measuring the inverter average input current. Also, the small-signal analysis performed allows obtaining the small-signal resonant inverter input impedance and studying the connection stability between PFC pre-regulator and inverter. The inverter small-signal analysis has been performed and an electronic ballast prototype for 250-W HPS lamps has been implemented and tested verifying the low-cost lamp power control method proposed.     

Design and analysis of automotive high intensity discharge lamp ballast using micro controller unit

A new scheme of the automotive high intensity discharge (HID) lamp ballast systems is proposed. The proposed scheme is consisted of the high frequency DC-DC converter and the low frequency DC-AC inverter as same as conventional HID ballast system. However this system separates the input voltage of the ignitor from DC link voltage using auxiliary winding, which results in the use of the lower voltage rating power devices for HID lamp ballast system compared with conventional system. As a result, proposed system has a lower cost or a higher efficiency. For the improvement of the efficiency, the proposed ballast controller using micro-controller unit (MCU), controls the frequency to operate the DC-DC converter in critical conduction mode. This paper presents the design and analysis of the proposed ballast and some experimental results.     

250W高压钠灯电子镇流器的研究

为满足人们对绿色照明的要求,该文设计了节能、高功率因数及总谐波失真低的高压钠灯电子镇流器来替代传统的电感式镇流器,采用有源功率因数校正、恒功率控制、低频方波驱动的三级式结构的电路设计,并搭建了样机,实现了160V～265V宽电压输入,功率因数PF≥0.99,总谐波畸变因数THD≤9．1％,电路可靠工作,通过了电磁兼容传导干扰测试。     

TRIAC dimmable ballast with power equalization

A two-stage, two-wire TRIAC dimmable electronic ballast for fluorescent lamps is presented in this paper. It is constructed by using a flyback converter as the input power factor corrector to supply a half-bridge series-resonant parallel-loaded inverter to ballast the lamp. The flyback converter is operated in discontinuous conduction mode so that the filtered input current profile is the same as the TRIAC-controlled voltage waveform. The switches in the inverter are switched at a constant frequency slightly higher than the resonant frequency of the resonant tank. Based on the constant average input current characteristics of the inverter, the dimming operation is simply achieved by pulsewidth modulation control of the magnitude of the flyback converter output voltage. No synchronization network is required between the input and output stages. In addition, a linear power equalization scheme is developed so that the dc-link voltage (and hence the lamp power) is in a linear relationship with the firing angle of the TRIAC. The average output voltage of the dimmer controls the equalized flyback converter output voltage. Modeling, analysis, and design of the ballast will be described. A prototype was implemented to verify the experimental measurements with the theoretical predictions.     

High power factor correction circuit for low-cost electronicballasts

A new low-cost high power factor correction circuit for electronic ballast is presented. The proposed circuit provides good power factor correction, low current harmonic distortion and cost-effectiveness. The prototype meets the IEC555-2 requirements satisfactorily with a power factor of nearly unity     

Implementation of a three-level rectifier for power factorcorrection

In this paper, a new single-phase switching mode rectifier (SMR) for three-level pulse width modulation (PWM) is proposed to achieve high input power factor, low current harmonics, low total harmonic distortion (THD) and simple control scheme. The mains circuit of the proposed SMR consists of six power switches, one boost inductor, and two DC capacitors. The control algorithm is based on a look-up table. There are five control signals in the input of the look-up table. These control signals are used to control the power flow of the adopted rectifier, compensate the capacitor voltages for the balance problem, draw a sinusoidal line current with nearly unity power factor, and generate a three-level PWM pattern on the AC side of adopted rectifier. The advantages of using three-level PWM scheme compared with two-level PWM scheme are using low voltage stress of power switches, decreasing input current harmonics, and reducing the conduction losses. The performances of the proposed multilevel SMR are measured and shown in this paper. The high power factor and low harmonic currents at the input of the rectifier are verified by software simulations and experimental results from a laboratory prototype