Exaggerated Grain Growth in ZrO2-Toughened Al2O3

Annealing of ZrO₂-toughened Al₂O₃ (ZTA) at elevated temperatures causes growth of both the intergranular ZrO₂ particles and the Al₂O₃"matrix" grains. Exaggerated ("breakaway") grain growth occurs in some, but not all, specimens. Analytical electron microscopy of two ZTA's, both of which contained a continuous amorphous (glassy) grain-boundary phase, but only one of which showed breakaway grain growth, revealed that the occurrence of breakaway grain growth could be correlated with the chemistry of the ubiquitous glassy grain-boundary phase.     

Strength-Toughness Relations in Sintered and Isostatically Hot-Pressed ZrO2-Toughened Al2O3

The fracture toughness of fine-grained undoped ZrO₂-toughened Al₂O₃ (ZTA) was essentially unchanged by postsintering hot isostatic pressing and increased monotonically with ZrO₂ additions up to 25 wt%. The strength of ZTA with 5 to 15 wt% tetragonal ZrO₂, which depended monotonically on the amount of ZrO₂ present before hot isostatic pressing, was increased by pressing but became almost constant between 5 and 15 wt% ZrO₂ addition. The strength appeared to be controlled by pores before pressing and by surface flaws after pressing; the size of flaws after pressing increased with ZrO₂ content. The strength of ZTA containing mostly monoclinic ZrO₂ (20 to 25 wt%) remained almost constant despite the noticeable density increase upon hot isostatic pressing because the strength was controlled by preexisting microcracks whose extent did not change on postsintering pressing. These strength-toughness relations in sintered and isostatically hot-pressed ZTA are explained on the basis of R -curve behavior. The importance of the contribution of microcracks to the toughness of ZTA is emphasized.     

Fabrication and Characterization of Three-Dimensional ZrO2-Toughened Al2O3 Ceramic Microdevices

Dense three-dimensional (3D) microdevices of ZrO₂-toughened Al₂O₃ (ZTA) were fabricated using microstereolithography and a subsequent sintering process. Using microstereolithography, 3D green bodies could be formed from a 40 vol% ZTA ceramic–resin paste. After sintering, the fabricated 3D devices are converted into dense ceramic devices without deformation. In this study, a gear (with a tooth edge of 25 μm) and a photonic crystal (with a lattice constant of 500 μm) were designed and fabricated. The dimensional accuracy of the fabrication process is within 20 μm and the sintering shrinkage is around 26% for these microdevices. The relative density of the sintered ZTA ceramics reached 96.5% of theoretical value. The measured hardness and toughness were about 14 GPa and 11 MPa m^1/2, respectively, in both the top and side surfaces. A band gap between 320 and 420 GHz was observed in the ZTA photonic crystal. The microstereolithography process can be easily applied to other ceramic materials and devices.     

Transformation and Microcrack Toughening as Complementary Processes in ZrO2-Toughened Al2O3

Both tetragonal ( t ) and monoclinic ( m ) ZrO₂ particles in ZrO₂-toughened Al₂O₃ can give rise to toughening. In the stress field of propagating cracks, the t -ZrO₂ particles can undergo the stress-induced t → m transformation, and the residual stresses around already-transformed m -ZrO₂ particles can cause microcracking. The t -ZrO₂ particles transformed in crack tip stress fields do not, however, also cause appreciable microcracking. The toughening increments via these distinct mechanisms are comparable. It appears that optimally fabricated Zr0₂-toughened Al₂O₃'s should contain a mixture of t - and m -ZrO₂.     

Low-Temperature Sintering of Seeded Sol—Gel-Derived, ZrO2-Toughened Al2O3 Composites

Seeding a mixture of boehmite (AIOOH) and colloidal ZrO₂ with α-alumina particles and sintering at 1400°C for 100 min results in 98% density. The low sintering temperature, relative to conventional powder processing, is a result of the small alumina particle size (∼0.3 μm) obtained during the θ-to α-alumina transformation, homogeneous mixing, and the uniform structure of the sol-gel system. Complete retention of pure ZrO₂ in the tetragonal phase was obtained to 14 vol% ZTA because of the low-temperature sintering. The critical grain size for tetragonal ZrO₂ was determined to be ∼0.4 μm for the 14 vol% ZrO₂—Al₂O₃ composite. From these results it is proposed that seeded boehmite gels offer significant advantages for process control and alumina matrix composite fabrication.     

Structure of Incoherent ZrO2/Al2O3 Interfaces

High-resolution electron microscopy was used to image incoherent ZrO₂/Al₂O₃ interfaces in ZrO₂-toughened Al₂O₃ containing intragranular ZrO₂. These particles are generally spherical but are sometimes faceted. High-resolution electron micrographs provide atomic-level information on the interfacial structure. For spherical particles, both ledgelike images and misfit dislocation-like images accommodated the lattice misfit, depending on the orientation of the interface, while faceted particles imply at least one low-energy ZrO₂/Al₂O₃ interface.     

Hot Forging Characteristics of Fine-Grained ZrO2 and Al2O3/ZrO2 Ceramics

Preliminary results indicate that large strains (∼80%) and strain rates (0.001 s⁻¹) can be obtained without tearing (or cracking) in fine-grain ZrO₂ (0.3 μm) and Al₂O₃/ZrO₂ (1 μm) ceramics. Alumina develops crystallographic and morphological texture as previously reported by Heuer et al.¹     

Tape Casting of Al2O3/ZrO2 Laminated Composites

Fracture toughness of ZrO₂-toughened alumina could he increased by macroscopic interfaces, such as those existing in laminated composites. In this work, tape casting was used to produce A/A or A/B laminates, where A and B can be Al₂O₃, Al₂O₃/5 vol% ZrO₂, and Al₂O₃/l0 vol% ZrO₂. An increase of toughness is observed, even in the Al₂O₃/Al₂O₃ laminates.     

Homogeneous ZrO2–Al2O3 Composite Prepared by Nano-ZrO2 Particle Multilayer-Coated Al2O3 Particles

ZrO₂–Al₂O₃ nanocomposite particles were synthesized by coating nano-ZrO₂ particles on the surface of Al₂O₃ particles via the layer-by-layer (LBL) method. Polyacrylic acid (PAA) adsorption successfully modified the Al₂O₃ surface charge. Multilayer coating was successfully implemented, which was characterized by ξ potential, particle size. X-ray diffraction patterns showed that the content of ZrO₂ in the final powders could be well controlled by the LBL method. The powders coated with three layers of nano-ZrO₂ particles, which contained about 12 wt% ZrO₂, were compacted by dry press and cold isostatically pressed methods. After sintering the compact at 1450°C for 2 h under atmosphere, a sintered body with a low pore microstructure was obtained. Scanning electron microscopy micrographs of the sintered body indicated that ZrO₂ was well dispersed in the Al₂O₃ matrix.     

Effect of ZrO2 Inclusions on the Sinterability of Al2O3

The sinterability of Al₂O₃/ZrO₂ composite powder compacts containing 2 and 10 vol% ZrO₂ was compared to the sinterability of their single-phase constituents through constant-heating-rate experiments. The ZrO₂ inclusion phase delayed the initiation of bulk shrinkage and the temperature of maximum strain rate by 100°C. The ZrO₂ inclusion phase also significantly inhibited grain growth. These results, discussed with regard to the thermodynamics of pore disappearance, suggest that phenomena inhibiting grain growth may also inhibit densification.     

Coupled Grain Growth Effects in Al2O3/10 vol% ZrO2

Coupled crystallization has been observed in the Al₃O₃/10%-ZrO₂ system by heating an amorphous precursor Al /Zr copolymerized alkoxide network structure. A finely divided two-phase material results which stabilizes tetragonal ZrO₂ to 1700°C and exhibits an unprecedented microstructure. During crystallization, the grain growth of ZrO₂ is coupled to the γ→α phase transformation of Al₂O₃.     

Subcritical Crack Growth in Y-TZP and Al2O3-Toughened Y-TZP

Crack velocity curves for Y-TZP and Al₂O₃-toughened Y-TZP were determined for long cracks in compact tension specimens with an in situ fracture device on the stage of an optical microscope. Indications for a crack velocity threshold were found for both materials. Above this threshold, at 2.6 MPa·m^1/2 for Y-TZP and 3.6 MPa·m^1/2 for Al₂O₃-toughened Y-TZP, chemically assisted subcritical crack growth occurs over an extended regime of applied stress intensity factors of width 2.1–2.8 MPa·m^1/2. It is recognized that the dependence of the shielding term on the crack-tip stress field renders transformation-toughened materials particularly susceptible to stress-corrosion cracking. This interrelation leads to the definition of a steady-state velocity at constant applied stress intensity factor. This velocity is obtained in the situation where the shielding term is fully defined by the present crack-tip stress field, not depending on prior loading history.     

Measurement of Stress Due to Thermal Expansion Anisotropy in Al2O3

The stress due to thermal expansion anisotropy in polycrystalline Al₂O₃ was measured. The broadening of spectroscopic R lines (692 and 693 nm, due to Cr³⁺ impurities) was used to measure the stresses (at 77 K) in samples with grain sizes of 50 to 150 μm that had been cooled, from 2150 K, at constant rates from 0.1 to 100 K/min. The maximum stress was found to vary from 80 to 100 MPa, depending on the thermal history of the sample. The results are compared to the predictions of a model based on stress relaxation by diffusional creep and are in good agreement for the dependence on cooling rate. No effect due to grain-size changes was observed due to the limited range of grain sizes accessible in this study.     

Hindrance of Grain Growth in Al2O3 by ZrO2 Inclusions.

Alumina and Al₂O₃/ZrO₂ (1 to 10 vol%) composite powders were mixed and consolidated by a colloidal method, sintered to >98% theoretical density at 1550°C, and subsequently heat-treated at temperatures up to 1700°C for grain-size measurements. Within the temperature range studied, the ZrO₂ inclusions exhibited sufficient self-diffusion to move with the Al₂O₃ 4-grain junctions during grain growth. Growth of the ZrO₂, inclusions occurred by coalescence. The inclusions exerted a dragging force at the 4-grain junctions to limit grain growth. Abnormal grain growth occurred when the inclusion distribution was not sufficiently uniform to hinder the growth of all Al₂O₃ grains. This condition was observed for compositions containing ≤2.5 vol% ZrO₂, where the inclusions did not fill all 4-grain junctions. Exaggerated grains consumed both neighboring grains and ZrO₂, inclusions. Grain-growth control (no abnormal grain growth) was achieved when a majority (or all) 4-grain junctions contained a ZrO₂ inclusion, viz., for compositions containing ≥5 vol% ZrO₂. For this condition, the grain size was inversely proportional to the volume fraction of the inclusions. Since the ZrO₂ inclusions mimic voids in all ways except that they do not disappear, it is hypothesized that abnormal grain growth in single-phase materials is a result of a nonuniform distribution of voids during the last stage of sintering.     

Metastable Phase Formation in Plasma-Sprayed ZrO2 (Y2O3)–Al2O3

Rapidly solidified ZrO₂ (Y₂O₃)–Al₂O₃ powders were prepared by melting fine-particle aggregates in a high-enthalpy plasma flame and then rapidly quenching them in cold water or on a copper chill plate. To ensure complete melting and homogenization of all the particles before quenching, the water-quenching treatment was often repeated two or even three times. The resulting melt-quenched powders and splats displayed a variety of metastable structures, depending on composition and cooling rate. ZrO₂-rich material developed an extended solid solution phase, whereas eutectic material formed a nanofibrous or amorphous structure. Under high cooling rate conditions, the ZrO₂-rich material developed a nanocomposite structure ( t -ZrO₂+α-Al₂O) directly by melt-quenching, whereas, more typically, such a structure was developed only after postannealing of the as-quenched metastable material.     

Load Dependence of Hardness in Sintered Submicrometer Al2O3 and ZrO2

Monolithic alumina bodies with a grain size of 0.5 μm and submicrometer tetragonal ZrO₂ (3 mol% Y₂O₃) polycrystals were produced and investigated. With decreasing indentation load, the hardness increases but may again decrease below about 5 N; relevant measurements require the application of fairly high loads. Decreasing grain sizes increase the hardness of alumina and zirconia ceramics even for very small grain sizes in the submicrometer range.     

High-Temperature Strength and Fracture Toughness of Y2O3-Partially-Stabilized ZrO2/Al2O3 Composites

The temperature dependence of bending strength, fracture toughness, and Young's modulus of composite materials fabricated in the ZrO₂ (Y₂O₃)-Al₂O₃ system were examined. The addition of A1203 enhanced the high-temperature strength. Isostatically hot-pressed, 60 wt% ZrO₂ (2 mol% Y₂O₃)/40 wt% Al₂O₃ exhibited an extremely high strength, 1000 MPa, at 1000°C.     

Thermal Grooving of MgO and Al2O3

High-purity polycrystalline MgO and Al₂O₃ were thermally grooved at 1500° and 1600°C. Accurate techniques were developed for following the growth of a single groove. For high-purity samples growth kinetics were essentially similar to those reported in the literature but were determined to be controlled by volume diffusion. Specimens for thermal grooving were prepared from Al₂O₃ to which transition metal oxides (Fe₂O₃₉, MnO, and TiO₂), which are known to accelerate shrinkage and sintering of Al₂O₃ powder compacts, had been added; the rate of groove growth was increased remarkably by minor amounts of these additives. Control of partial pressure indicated that Fe²⁺ and Ti⁴⁺ are the species active in promoting groove growth. Substantial evidence was found for volume diffusion as the mechanism controlling groove formation.