A Statistical Signal Prediction Model for Communication Receivers

Many communication receivers receive the desired signal in presence of interference signal. A statistical antenna and propagation model is described which predicts the expected values of the desired and undesired signal levels ? and ?, respectively, the standard deviations of the desired and undesired signals ?s and ?I, respectively, and their correlation coefficients PSI. The expected values of the signal levels are expressed in terms of the random parameters of the radio frequency power fed into the transmitting antenna, its efficiency, gain, propagation path loss, receiving antenna gain, receiving antenna loss, and input impedance of the receiver.     

Adjacent channel interference cancellation for MSK-type signals using antenna diversity in Rayleigh fading environment

This paper addresses the problem of adjacent channel interference between minimum-shift keying (MSK)-type signals transmitted through Rayleigh fading channels. A receiver, based on the multiple-input, multiple-output antenna diversity concept and the maximum-likelihood criterion, allows the transmission of MSK-type signals with very small channel spacings, greatly improving the bandwidth efficiency of these signals. The concept of antenna diversity is used to greatly reduce the effects of adjacent channel interference for channels with Rayleigh fading. The results show that it is possible to transmit bit-synchronized MSK-type signals with a very small normalized channel spacing (e.g., /spl Delta/fT/sub b/=/spl plusmn/0.4) between channels, under almost any power imbalance between signals, with very small degradation in performance.     

A 40 GHz single-ended down-conversion mixer in 0.13 /spl mu/m SiGeC BiCMOS HBT

This work presents a single-ended active mixer realized with a 0.13 /spl mu/m BiCMOS SiGeC heterojunction bipolar transistor (HBT) technology. This mixer is designed to be integrated in a superheterodyne receiver for 40 GHz wireless communication systems. Local oscillator (LO) and RF signals are directly applied to the base of the HBT through two coupled lines. The mixer provides a down-conversion from 42 GHz to 2 GHz. The mixer exhibits a power conversion gain better than 2.4 dB and a measured double-sideband noise figure less than 8.3 dB for P/sub LO/=3 dBm (power of the local oscillator) under a global power consumption lower than 9.5 mW. This architecture exhibits good linearity performance with a measured IP/sub 1dB/ of about -7 dBm and an IIP3 of +4 dBm. The linear dynamic range for a 2 GHz system bandwidth is approximately 65 dB for P/sub LO/=+2 dBm and T/sub 0/=290 K. The third order spurious free dynamic range is calculated to be better than 52 dB.     

Deterministic signals and interference in FM reception: The "Instantaneous" approach, with undistorted inputs

The purposes of this study are several: 1) to extend earlier models of the FM reception process, to include as much "realism"-i.e., nonideality of both the linear and nonlinear elements of the typical FM receiver-as possible, and still retain analytical and computational feasibility; 2) to examine explicit cases of interference produced by one or more deterministic signals; and 3) with such specific examples, both to provide insights into the distortion effects generated by the nonlinar interactions of the various (desired and undesired) signals in the receiver and to present the analytical framework of the instantaneous outputs required in any (subsequent) fully statistical treatment, where now the interference (e.g., "noise") is noticeably non-Gaussian. In addition, these deterministic models may also provide useful structures for simulation studies. The instantaneous receiver outputs are obtained for the following receiver models (A) and interference "scenarios" (B). For (A), (I) "superclipping" and an ideal discriminator; (II) no limiting and ideal discriminator; (III) "superclipping" and a nonideal discriminator; (IV) no limiting and a nonideal discriminator. For (B), with each (A), we consider explicitly the cases of: (i)one cochannel interfering signal; (ii) one adjacent channel interferer, and (iii) M symmetrical interferers (M = 1, 5). All the above are obtained here for idealized (i.e., sufficiently wide-band) RF-IF receiver stages, which are essentially linear under this condition. The results are illustrated with cases for selected, typical parameters of the combination of the interference-receiver structure.     

A method of surface clutter cancellation for an underground CWradar

An RF signal similar to the undesired signals is synthesized and used to cancel the undesired portion of the received signal from the antenna before it reaches the receiver. With a progressing degree of cancellation, the transmitter power is accordingly increased to expand the dynamic range of the radar. A canceller subsystem is proposed to eliminate undesired signals such as surface reflection and mutual coupling between antennas     

PN acquisition for DS/SS using a preloop parallel binary search phase estimator and a closed-loop selective search subsystem

An acquisition method of long pseudo-noise (PN) sequences in direct-sequence spread spectrum (DS/SS) systems is presented. The concurrent cross correlation of locally generated auxiliary signals with the incoming PN sequence produces binary search estimates leading to an initial approximation of the input signal's PN offset. The PN receiver then uses a closed-loop subsystem to determine the true offset of the incoming PN signal. New phase estimates are generated from successive corrections of likely errors in the binary search. The acquisition scheme's average acquisition time and its variance are analytically determined. Simulation results show that the proposed acquisition scheme is faster than the conventional serial receiver. A hybrid serial/parallel PN acquisition receiver is used for comparing the acquisition performance given similar hardware complexity. The hybrid receiver used the same number of parallel correlators as used in the proposed receiver's input phase estimator. Simulation results show that the proposed system provides an improved performance under normal operating conditions.     

Blind space-time multiuser channel estimation in time-varying DS-CDMA systems

A multistep linear prediction (MSLP) approach is presented for blind channel estimation for short-code direct sequence code division multiple access signals in time-varying multipath channels using a receiver antenna array. The time-varying channel is assumed to be described by a complex exponential basis expansion model. First, a recently proposed MSLP approach to blind channel estimation for time-varying single-input multiple-output (SIMO) systems is extended to time-varying multiple-input multiple-output (MIMO) systems to define a "signal" subspace. Second, the knowledge of the spreading code of a desired user is exploited in conjunction with the signal subspace to estimate the time-varying channel of the desired user up to an unknown time-invariant scale factor. Equalization/detection for the desired user can be then carried out if the information sequence is differentially encoded/decoded. Sufficient conditions for channel identifiability are investigated. Three illustrative simulation examples are provided.     

Behavioral-level event-driven power management for DECT digital receivers

Power management is a low-power design technique applicable in almost all design levels. Here, the idea of exploiting events to trigger the shut-down of hardware resources is applied at the behavioral-level of a DECT digital receiver design. Power management involves a trade-off between the power savings arising from the power-down (or shut-down) parts of the system and the power increase due to the additional logic for the generation of the shutdown signals. For that purpose, taking into account the digital receiver's characteristics, a behavioral-level power management technique is introduced. The efficiency of the proposed technique is proven by its application on an industrial DECT receiver, where a power saving of 50% in terms of the dynamic power consumption is achieved.     

Subspace-based active user identification for a collision-free slotted ad hoc network

We propose a novel spreading code scheme, transmitter-receiver-based code, for wireless ad hoc networks. The design facilitates collision resolution using multiuser detection at each node, and is more bandwidth efficient than creating orthogonal channels in time or frequency. A subspace-based receiver structure is introduced, which identifies users of interest, or "active" users, with minimal prior information on the spreading code ensemble. A subspace-based blind multiuser detector can then be implemented to suppress multiaccess interference. The performance of the proposed active user identifier is studied by investigating its false alarm rate P/sub f/ and miss rate P/sub m/. Tradeoffs between P/sub f/ and P/sub m/ are discussed, and a graphical method to determine the threshold value d/sub th/ of the decision statistic used in discriminating between active and inactive channels is introduced.     

DTV repeater emission mask analysis

Terrestrial digital television (DTV) requires careful planning in the allocation of RF channels, especially during the transition period when intermixing both analog and digital signals in the same coverage area. One important issue to consider is adjacent channel interference, which limits the number of RF channels utilized in any given area. This issue is important in the deployment of not only full service stations, but also of secondary stations such as translators, on-channel repeaters, and low power television stations. Full service stations have FCC rules that limit the amount of adjacent channel splatter by requiring the splatter energy to remain below a rigid emission mask. Currently there are no FCC rules for translators and low power television stations. The paper discusses typical DTV transmitter splatter sidebands and their causes, as well as specific methods for interference analysis from adjacent channel DTV splatter into adjacent NTSC or DTV signals. Two rigid emission masks ("simple" and "stringent") are proposed and evaluated. Several filter designs are computer simulated and analyzed for minimizing adjacent channel splatter interference as well as in-band DTV signal degradation. Linear pre-correction techniques are analyzed for various length (15-tap and 31-tap) transversal filter equalizers. The simulation is verified by measuring and evaluating DTV system performance for two hardware band-pass filters individually placed at the output of a low power (30 W average) transmitter.     

Digitized speech transmission at VHF using existing FM mobile radios

An extensive study of digitized speech transmission over existing VHF FM mobile radio sets is presented. Objective criteria expressed in terms of bit error rate (BER) are determined for the performance evaluation of analog FM radios when transmitting digital voice. These criteria are used to define the technical characteristics such as the receiver sensitivity, co-channel rejection, and adjacent channel selectivity in the case of digital FM transmission. The concept of performance measurements of existing sets in the digital mode of operation is suggested. The results of performance measurements reported here include the following: 1) radiated FM spectra, 2) bit error rate curves, 3) receiver sensitivity, 4) BER performance in the presence of analog or digital FM interference on the same or adjacent channel, 5) signal plus noise plus distortion to noise plus distortion ratio (SINAD) performance in the presence of co-channel or adjacent channel interference for both types of interfering signals, 6) co-channel rejection and adjacent channel selectivity for various combinations of the wanted and interfering signals, 7) receiver selectivity for both modes of operation, and 8) adjacent-signal selectivity for various combinations of the desired and undesired signals. Optimum values of design parameters of digital voice radio system are deduced from the obtained results. Finally, the implications of digitized speech transmission on the technical characteristics, operating range, channel reuse distance, and adjacent channel interference performance of analog FM radios are discussed.     

Analyses of numerical and experimental results for optical signal generation using heterodyne scheme

In this paper, we have proposed a heterodyne technique to generate an optical millimeter-wave signal for ultra-wideband communication. First, we have investigated the characteristics of semiconductor lasers locked to another semiconductor under the RF modulation having many sidebands. The RF-modulated master laser is represented by a series of Bessel functions. This model is then inserted into Lang's rate equations. By numerically solving the resulting rate equations, we have determined the locked laser output characteristics as well as the RF spectrum of the beat signals. The result is that the unselected sidebands can produce undesired beat signals whose power may be comparable to that of the desired beat signal. Furthermore, their strength is affected by the injected ML light power. With reduced ML light, undesired beat signals and the injection-locking bandwidth can be suppressed. Second, we have experimented a new technique for generating millimeter-wave signals from a semiconductor laser. A 32 GHz signal is generated using a multisection semiconductor laser operated under a continuous wave by injecting optical pulses at a repetition rate equal to the fourth subharmonic (8 GHz). The generated millimeter-wave signal exhibits a large subharmonic suppression ratio, a large frequency detuning range, low levels of phase-noise and a large locking range. These simulation results are confirmed by experimental results. The high-frequency signal can be used in the field of ultra-wideband communication employing local multipoint distribution system (LMDS), wireless local loop (WLL) and mobile broadband system (MBS).     

Analysis, design and experimental results of a high-frequency power supply for spark erosion

The LC/sub s/C/sub p/ resonant converter finds a new application in an electrical discharge machining (EDM) power supply, which is designed for the purpose of developing small size EDM systems. The switching frequency is tuned to the natural resonant frequency where the converter tends to act as a current source. In this way, three effects are achieved: 1) the necessary over-voltage is generated, first to ionize the dielectric and then to establish the electric discharge, 2) a constant current is supplied during the machining of the workpiece, providing the circuit with inherent protection under short circuit conditions, and 3) overall stability is guaranteed despite the equivalent negative resistance of the dielectric breakdown. The proposed control achieves an optimum and stable operation using tap water as dielectric fluid preventing the generation of undesired impulses and keeping the distance between the electrode and the workpiece within the optimum stable range. The EDM power supply has been validated to perform operations in a nuclear power plant application.     

Digital audio broadcasting in the FM band based on continuous phase modulation

A method for broadcasting digital audio signals simultaneously with existing analog frequency modulation radio (88-108 MHz) in adjacent channels is presented. The digital transmission is based on continuous phase modulation (CPM) and a proper reduced-state sequence estimator. With the proposed method, the power level and the symbol rate of the transmitter signal is determined in a manner that the interference the CPM signal poses for the analog FM signal in adjacent channels remains below a level according to the radio frequency emission mask defined by international rules. Due to the multipath propagation of the transmitted signal, the transmission behavior of the radio channel is determined by high dispersion up to 85 /spl mu/s. With the selected bit rate, the receiver has to cope with a channel memory of up to 17 bits. Since Viterbi detection is not feasible due to the number of channel states, detection is performed by a reduced-state sequence estimator that is able to eliminate the complete channel interference by decision feedback. Simulation results show that the detector almost achieves the detection quality of the optimum receiver. CPM achieves data rates of up to 200 kb/s inside a 200 kHz FM channel, which is sufficient for transmission of digital compressed audio signals at compact disc quality. The encouraging results of field tests will be published in another paper.     

Mode Analytical Study of Cylindrical Cavity Power Combiners

A mode analytical treatment of cylindrical cavity power combiners is presented to discuss power-combining capability and the method for attaining stable desired mode operation. Both the conventional coaxial-probe output type and the window output type are treated, based on a circuit model which can support TM/sub 010/, TM/sub 020/, and TM/sub m10/ modes (1<=m<=N, N being the number of active devices employed). It is shown that adoption of the window output largely facilitates undesired mode suppression and also enables power combining in some azimuthal modes.     

Joint Downlink Beamforming and Time-Reversed Matched Filtering for Multiuser UWB Signals

This paper proposes a simple delay-line (DL) downlink beamformer for pulsed ultra-wideband (UWB) systems to compensate for propagation delay, which is detrimental to UWB signals. Moreover, we propose a prefiltering-based transmission scheme at the fixed access point (i.e., base station) by shifting the signal processing needs from the receiver at the mobile unit to the transmitter where power and computational resources are plentiful. The DL transmitter array can steer signals to the direction of the desired mobile user such that the desired signals stemming from each antenna are coherently combined and the multiuser interference (MUI) is averaged out. Furthermore, the prefiltering scheme is composed of a set of time-reversed matched filters (TR MFs) subject to multiple-input single-output (MISO) finite impulse response (FIR) channels. A simple correlation receiver is proposed at the mobile unit to extract the information of the time-hopping (TH) UWB signal. The performances under different scenarios are extensively evaluated.     

UHF-TV Taboos: The FCC Electromagnetic Compatibility Plan for UHF Television

The constraints of assignment of channels to UHF TV stations are discussed, taking into account the radiated signal characteristics, the various undesired responses of receivers to signals on other than the channel to which they are tuned and effects of receiver local oscillator radiation. These "taboos" affect the assignment of many other channels for each assigned channel, due to the geographical separation requirements associated with the respective taboos. The basis for each taboo, the mileage separation required and the effects on assignment planning are discussed.     

A new blind receiver for downlink DS-CDMA communications

A linear receiver is proposed for downlink DS-CDMA communications over unknown frequency-selective fading channels. The new receiver exploits the fact that all synchronized downlink signals go through the same channel and recovers the desired signal with a constrained channel equalizer followed by a despreader. Such a scheme allows the receiver to operate blindly in a time varying environment for both periodic CDMA and aperiodic CDMA systems     

A multidimensional phase-locked loop for blind multiuser detection

This paper concerns the problem of blind multiuser detection, a special case of the blind source separation problem in which the source signals have finite alphabets. Specifically, we address the problem of identifying and resolving the n/spl times/n unitary matrix ambiguity U that results from whitening the receiver observations, where n is the number of sources. We propose the multidimensional phase-locked loop (MPLL) as a generalization of a scalar decision-directed PLL to vector-valued signals. The MPLL adapts an estimate of U according to the recursion U/spl circ//sub k+1/=U/spl circ//sub k/R/sub k/, where R/sub k/ is an n-dimensional Householder-like rotation depending on only the kth receiver observation. The O(n/sup 2/) complexity of an efficient implementation of the algorithm is extremely low. Nevertheless, simulation results demonstrate good convergence properties and superior steady-state performance when compared with prior techniques. The algorithm is also able to accommodate large alphabets and shaped alphabets.     

On quantifying the benefits of SSPA linearization in UWC-136 systems

A novel comparative analysis of the benefits brought by different degrees of linearization to offset the modulation fidelity (MF) and spectrum regrowth impairments caused by solid-state power amplifier (SSPA) nonlinearity, as measured by error vector magnitude (EVM) and adjacent channel power ratio (ACPR) performance for TIA/EIA Universal Wireless Communication standard UWC-136 signals, are quantified. New results are presented showing the benefits of even modest levels of linearization but also that such benefits may be easily eroded at a receiver by the adjacent channel interference (ACI) in certain circumstances. An equation expressing the incremental MF deterioration experienced by a wanted channel (WC) signal, at its receiver, due to ACI arising from signals in the immediate upper and lower frequency channels, and as a function of adjacent channel (AC) to WC power differential, where signals are subject to different degrees of linearization, is presented. Typical SSPA characteristic values for the equation constants in the cases of one and two immediate AC signals are derived from simulation results. Interesting new results and conclusions relevant to the drafting of harmonious ACPR-EVM specifications and on the advisability of the inclusion of linearization schemes in transmitters, in the context of the UWC-136 system, are presented.