Electroconductive and catalytic performance of polypyrrole/montmorillonite/silver composites synthesized through in situ oxidative polymerization

The present study demonstrates a simple approach to the formation of polypyrrole/montmorillonite/silver (PPy/Mt/Ag) composites via in situ oxidative polymerization of pyrrole (Py) in the presence of AgNO₃ acting as a direct oxidant. The polymerization was performed in the presence of dodecylbenzenesulfonic acid, which acts as a stabilizing and doping agent. The morphological, structural, and thermal properties of PPy/Mt/Ag composites are discussed in detail and a possible formation mechanism is proposed. The electrical conductivities of the composites pressed at different pressing pressures were investigated using four‐probe analyzer. X‐ray diffraction, transmission electron microscopy, and scanning electron microscopy results indicated the partially exfoliated structure of the composites and Fourier transforms infrared results suggested the strong interactions between Si? O? Si groups in Mt and N? H groups in PPy chains. The addition of Mt in the PPy polymer enhanced thermal property of the polymer. The conductivity of 1.08 S cm^?1 was observed in the sample with 20 wt % Mt loading and applied pressure of 5 MPa. The composites obtained in the present study catalyze the reduction of methylene blue by sodium borohydride, achieving 92% conversion of MB to colorless within a few minutes. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45986.     

Enhanced microwave absorbing properties of lightweight films based on polyaniline/aliphatic polyurethane composites in X band

Polymer blends based on nanostructured polyaniline (PANI) doped with hydrochloric acid (HCl) and para‐toluene sulfonic acid (PTSA) introduced into aliphatic polyurethane matrix (PU) are synthesized to produce flexible thin composite films for microwave absorbers. The effects of dopant type, PANI content and film thickness on morphologies, dielectric and microwave absorption properties in the X‐band are studied. It reveals that real and imaginary parts of the complex permittivity are proportional to filler concentrations and type of doped PANI. The PANI‐PTSA/PU films show higher permittivity and better microwave absorbing properties than PANI‐HCl/PU for the same weight fraction of PANI. The minimum reflection loss RL_(dB) values for the PANI‐PTSA/PU are ?37 dB at (20% PANI and 11.6 GHz) and ?30 dB at (15% PANI and 11.3 GHz) for thicknesses of 1.2 and 1.6 mm, respectively. These high values of reflection losses make the obtained lightweight and flexible composites promising radar absorbing materials (RAM). © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40961.     

Polyaniline grafted chitosan/GO-CNT/Fe3O4 nanocomposite as a superior electrode material for supercapacitor application

Developing appropriate stable electroactive electrode materials for supercapacitor application is the challenging issue, which attracts enormous attention in recent decades. In this regard, Fe₃O₄ nanoparticles are firstly synthesized on chitosan/graphene oxide-multiwall carbon nanotubes (CS/GM/Fe₃O₄). Then, polyaniline (PANI) is grafted on it via in situ chemical polymerization and named as CS/GM/Fe₃O₄/PANI. The as-prepared nanocomposites are characterized by Field emission scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and energy dispersive X-ray spectroscopy. The capacitive properties of the electrodes are investigated in a three electrode configuration in 0.5 M Na₂SO₄ electrolyte by various electrochemical techniques. The specific capacitance of CS/GM/Fe₃O₄/PANI electrode is 1513.4 Fg⁻¹ at 4 Ag⁻¹ which is 1.9 times higher than that of CS/GM/Fe₃O₄ (800 Fg⁻¹). Meanwhile, the electrodes exhibit appropriate cycle life along with 99.8% and 93.95% specific capacitance at 100 Ag⁻¹ for chitosan/GO-CNT/Fe₃O₄ and polyaniline grafted chitosan/GO-CNT/Fe₃O₄, respectively.     

Synthesis and characterization of a conducting polyaniline/TiO2−SiO2 composites

Polyaniline/TiO₂?SiO₂ composites were prepared by an in situ chemical oxidation polymerization approach in the presence of hybrid TiO₂?SiO₂ fillers. The obtained polyaniline/TiO₂?SiO₂ composites were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared spectrometer (FTIR), X‐ray diffraction (XRD), thermogravimetry (TG), and current?voltage (I?V) measurements. SEM picture shows a variation in morphology of polyaniline (PANI) from fiber shape to relatively regular particle shape with increasing TiO₂?SiO₂ contents in the composites. The floccule‐like structures were observed by high resolution TEM, which may help improve the efficiency of conductive network. SEM, XRD, TG, and FTIR spectra all reveal that a relatively strong interaction exist between TiO₂?SiO₂ and PANI. The I?V characteristics in such composites indicate that the charge transport is mainly governed by the space charge effects, which occurs at the interface between the conducting PANI and TiO₂?SiO₂. Meanwhile, PANI/TiO₂?SiO₂ composites exhibit significant increase in conductivity than PANI/TiO₂ or PANI/SiO₂. The reasons about high conductivity of PANI/TiO₂?SiO₂ have also been discussed. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2288–2295, 2013     

Synthesis and characterization of nylon 6/polyalkylaniline conducting composites

Conducting composite films of polyalkylanilines with nylon 6 as the insulating matrix were electrochemically synthesized and characterized. The electrochemical properties of the alkylanilines and their composites were investigated with a cyclic voltammetry technique. The magnetic properties of the polymers and composites were analyzed, and their conducting mechanisms were found to be of bipolaron nature. With Fourier transform infrared spectra, it was clarified that polymerization occurred via the ? NH₂ group in a head‐to‐tail mechanism. Through thermogravimetric analyses, the thermal properties of the polymers and their composites were elucidated. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1693–1701, 2003     

Electrochemical synthesis and In situ spectroelectrochemistry of conducting NMPy‐TiO2 and ZnO polymer nanocomposites for Li secondary battery applications

Poly(N‐methylpyrrole) (PNMPy), poly(N‐methylpyrrole‐TiO₂) (PNMPy‐TiO₂), and poly (N‐methylpyrrole‐ZnO) (PNMPy‐ZnO) nanocomposites were synthesized by in situ electropolymerization for cathode active material of lithium secondary batteries. The charge–discharging behavior of a Li/LiClO₄/PNMPy battery was studied and compared with Li/LiClO₄/PNMPy‐nanocomposite batteries. The nanocomposites and PNMPy films were characterized by cyclic voltammetry, in situ resistivity measurements, in situ UV–visible, and Fourier transform infra‐red (FTIR) spectroscopy, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The differences between redox couples (ΔE) were obtained for polymer nanocomposites and PNMPy films. During redox scan, a negative shift of potential was observed for polymer nanocomposite films. Significant differences from in situ resistivity of nanocomposites and PNMPy films were obtained. The in situ UV–visible spectra for PNMPy and polymer nanocomposite films show the intermediate spectroscopic behavior between polymer nanocomposites and PNMPy films. The FTIR peaks of polymer nanocomposite films were found to shift to higher wavelengths in PNMPy films. The SEM and TEM micrographs of nanocomposite films show the presence of nanoparticle in PNMPy backbone clearly. The result suggests that the inorganic semiconductor particles were incorporated in organic conducting PNMPy, which consequently modifies the properties and morphology of the film significantly. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41526.     

Preparation and enhanced electrochemical properties of Ag/polypyrrole composites electrode materials

Ag/polypyrrole (PPy) composites were synthesized with different dispersants via interface polymerization method. The morphology of the composites was investigated by scanning electron microscopy and transmission electron microscopy, and the results showed that the dispersant had strong effect on the morphology of the obtained composites. The structure of the products was characterized by Fourier transform infrared spectroscopy, and X‐ray diffraction. The specific capacitance and impedence of Ag/PPy composites electrode was evaluated through charge/discharge measurements and electrochemical impedance spectroscopy, respectively. Electrochemical performances indicated that Ag/PPy composite electrode used polyvinyl alcohol as dispersant exhibited the highest specific capacitance of 635.5 F/g at a current density of 2.45 mA/g, which provided potential application as supercapacitor materials. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Chemical preparation of conducting polyfuran/poly(2‐chloroaniline) composites and their properties: A comparison of their components,polyfuran and poly(2‐chloroaniline)

Conductive homopolymers and composites of poly(2‐chloroaniline) (P2ClAn) and polyfuran (PFu) were synthesized chemically in hydrous and anhydrous media, and their properties were investigated. The polymers and composites were characterized by Fourier infrared spectroscopy, ultraviolet‐visible absorption spectroscopy, thermogravimetric analysis, differential scanning calorimetry, scanning electron microscopy, magnetic susceptibility, and conductivity measurements. It was found that the PFu/P2ClAn composite is thermally more stable than both the P2ClAn/PFu composite and the homopolymers. It was determined from Gouy scale measurements that conducting mechanisms of homopolymers and composites are polaron and bipolaron in nature. It was observed that the conductivity and magnetic susceptibility values changed with a changing amount of the guest polymer in the prepared composites. The conductivity (3.21 × 10^?2 S/cm) of the P2ClAn/PFu (55.8% m/m) composite was found to be higher than the conductivities of both homopolymers (σ_PFu = 1.44 × 10^?5 S/cm; σ_P2ClAn = 1.32 × 10^?3 S/cm). It was determined that the composites synthesized had different conductivities and morphological and thermal properties from changing synthesis order. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2924–2931, 2003     

Synthesis and characterization of secondary doped polypyrrole/organic modified attapulgite conductive composites

Secondary doping method was introduced into fabricating polypyrrole/oganic modified attapulgite conductive composites. The preparation conditions, such as amount of hexadecylpyridinium chloride (CPC, modifying agent), organic modified attapulgite (OATP), and HCl (secondary dopant) have been optimized to get the composites with the highest conductivity. When m_CPC/m_ATP, m_OATP/m_Py, and n_HCl/n_SA (SA is sulfamic acid) reaches 0.03, 0.6, and 0.5, respectively, the PPy/OATP composites possess the highest conductivity of 87.59 S cm^?1 as well as the highest thermal degradation temperature of 249.29°C. Scanning electron microscopy, transmission electron microscopy, X‐ray diffraction, Fourier transform infrared spectroscopy, UV‐Visible diffuse reflectance study, and X‐ray photoelectron Spectroscopy results showed that PPy chains form the core‐shell structure and may combine with OATP via π–π stacking interaction. Thermogravimetric analysis showed that the thermal stability of PPy/OATP‐SH composites was enhanced and these could be attributed to the retardation effect of OATP as barriers for the degradation of PPy. This method may open a new door for PPy‐based composites with special structures, higher performance, and thus broader application ranges. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41407.     

PANI-chitosan-TiO2 ternary nanocomposite and its effectiveness on antibacterial and antistatic behavior of epoxy coating

A straightforward approach has been developed for fabricating antibacterial and antistatic epoxy coatings by using polyaniline-chitosan modified TiO₂ ternary nanocomposite. This nanocomposite was synthesized through the following steps. First, chitosan was grafted onto the TiO₂ nanoparticles and then final nanocomposite was prepared via solution polymerization of aniline. Electrical conductivity measurement revealed that nanocomposite with 7.5 wt % of the modified TiO₂ nanoparticles has noticeably higher conductivity compared to polyaniline. Evaluating the coatings' antibacterial property indicated epoxy coatings with the content of ternary nanocomposite show significant bactericidal activity against Gram-positive bacteria and have acceptable antibacterial action against Gram-negative ones. Also, obtained results showed that the ternary nanocomposite would greatly decrease coatings' surface resistivity and when nanocomposite content is about 2 wt % surface resistivity is about 3 × 10⁷ Ω sq⁻¹. On the contrary, the coating with nanocomposite loading exhibits improved thermal and mechanical performance compared to the coating made of neat epoxy. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47629.     

Development of heating elements based on conductive polymer composites for electrofusion welding of plastics

Conductive polymer composites have been developed based on high-density polyethylene filled with carbon black (HDPE-CB), capable of generating heat when an electric voltage is applied. For each voltage value, the composite reached a constant value of equilibrium temperature, which obeyed a quadratic dependence on voltage and a linear dependence on electric power. The possibility of using such composites as heating elements (HE) for electrofusion welding of polyethylene adherents was evaluated in two modes, ''hard'', when high voltage was applied for a short welding time, and ''soft'', in which a stepwise regime of the applied voltage and a longer welding time were used. The latter provided a stronger welded joint. Using HE based on the HDPE-CB composites for welding of butt and lap joints of the polymer materials enabled to obtain welded joints with high strength.     

A novel hydrogen peroxide sensor based on Ag nanoparticles decorated polyaniline/graphene composites

A novel electrochemical sensor based on Ag nanoparticles (AgNPs) decorated polyaniline/graphene composites (PANI/G) is developed, which can be used for sensitive determination of H₂O₂. For the construction of the H₂O₂ sensor, polyaniline (PANI) is first electrodeposited on the surface of graphene (G) to form PANI/G, and then horseradish peroxidase (HRP) loaded on AgNPs (HRP/AgNPs) is immobilized on to the PANI/G. H₂O₂ can be catalyzed by HRP to generate current response which can be significantly enhanced by AgNPs, and thus the PANI/G based sensor can be utilized for the detection of H₂O₂. Under the optimized conditions, the proposed H₂O₂ sensor exhibits wide linear response to H₂O₂ concentration ranging from 0.25 to 2.25 mM with a detection limit of 0.03 mM (signal‐to‐noise ratio of 3), and it also shows high selectivity and reproducibility. The method is simple and cost‐effective, and can be a promising candidate as the sensitive sensing platform for H₂O₂. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42409.     

Preparation and electrochemical performance of modified Ti3C2Tx/polypyrrole composites

MXenes with a large surface area have been widely studied to improve the pseudocapacitance of electrode materials by combining conductive polymer materials. In this article, a superficial strategy to enhance the electrochemical properties by in situ polymerization of a pyrrole monomer between the Ti₃C₂T_x layers modified with 1,5-naphthalene disulfonic acid (NA) and cetyltrimethylammonium bromide (CTAB) was investigated. It is found that polypyrrole (PPy) and Ti₃C₂T_x can be combined through strong interactions between each other, and the specific capacitance of the modified Ti₃C₂T_x/PPy composite was increased to a maximum value of 437 F g⁻¹, which was more than thrice higher than that of pure PPy. The composite also exhibited good cycling performance (76% capacitance retention after 1000 cycles). Moreover, owing to the synergistic effect between the PPy and Ti₃C₂T_x layers, the composite provided better electron or ion transfer and surface redox processes than that of pure PPy, which indicated that this composite can be used as a promising electrode material for supercapacitors. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47003.     

Preparation of conducting polysiloxane/polyaniline composites

Polysiloxane/polyaniline microcomposites were prepared, in which polyaniline particles act as filler, thus combining the mechanical properties of polysiloxane matrix with conductivity of polyaniline. Two syntheses were evaluated: (1) homogeneous dispersion of a polyaniline colloid in the reaction mixture from which the polysiloxane matrix subsequently formed, and (2) the blending of previously prepared dry polyaniline particles with a liquid oligomeric siloxane resin followed by cure (“heterogeneous method”). Both methods lead to composites with evenly distributed filler. Electrical conductivity was achieved above 40 wt % of polyaniline, which is better obtained by the “heterogeneous” method. During the composite cure, the polyaniline particles, which are softer than the matrix, act as a catalyst and cause more efficient matrix crosslinking, thus leading to somewhat raised moduli. Although particulate fillers usually deteriorate the impact toughness, in the case of the prepared composites, the impact toughness was preserved due to the softer consistence of the filler, which hinders crack propagation. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42429.     

Capacitance properties of graphite oxide/poly(3,4‐ethylene dioxythiophene) composites

Poly(3,4‐ethylene dioxythiophene) (PEDOT) and graphite oxide (GO)/PEDOT composites (GPTs) doped with poly(sodium styrene sulfate) (PSS) were synthesized by in situ polymerization in aqueous media. The electrochemical capacitance performances of GO, PEDOT–PSS, and GPTs as electrode materials were investigated. The GPTs had a higher specific capacitance of 108 F/g than either composite constituent (11 F/g for GO and 87 F/g for PEDOT–PSS); this was attributable to its high electrical conductivity and the layer‐within/on‐layer composite structure. Such an increase demonstrated that the synergistic combination of GO and PEDOT–PSS had advantages over the sum of the individual components. On the basis of cycle‐life tests, the capacitance retention of about 78% for the GPTs compared with that of 66% for PEDOT–PSS after 1200 cycles suggested a high cycle stability of the GPTs and its potential as an electrode material for supercapacitor applications. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Chemical synthesis,characterization, and direct‐current conductivity studies of polypyrrole/γ‐Fe2O3 composites

The in situ polymerization of pyrrole was carried out in the presence of γ‐Fe₂O₃ to synthesize polypyrrole/γ‐Fe₂O₃ composites by a chemical oxidation method. The polypyrrole/γ‐Fe₂O₃ composites were synthesized with various compositions, including 10, 20, 30, 40, and 50 wt % γ‐Fe₂O₃ in pyrrole. The polypyrrole/γ‐Fe₂O₃ composites were characterized with X‐ray diffractometry and infrared spectroscopy. The surface morphology of these composites was studied with scanning electron microscopy. The direct‐current conductivity was studied from 40 to 200°C. The dimensions of the γ‐Fe₂O₃ particles in the matrix had a greater influence on the conductivity values. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2797–2801, 2007     

One‐step oxidation of aniline by peroxotitanium acid to polyaniline–titanium dioxide: A highly stable electrode for a supercapacitor

In this study, to make a stable electrode material for a supercapacitor, we selected a polyaniline and titanium dioxide (TiO₂) hybrid material. Peroxotitanium acid was used to oxidize aniline in the presence of sulfuric acid to a poly(aniline sulfate) salt–titanium oxide composite in one step. IR, X‐ray diffraction, and energy dispersive X‐ray analysis (EDAX) analyses supported the formation of the composite. The poly(aniline sulfate) salt–titanium oxide composites (50 wt % each) showed an amorphous, flakelike morphology having a conductivity value of 8 × 10^?3 S/cm with an excellent yield and stability (300°C).This composite material in the cell configuration showed a specific capacitance of 320 F/g at a 0.33 A/g discharge current density. Thirty thousand charge–discharge (CD) cycles at a heavy CD current density of 3.3 A/g were carried out on the supercapacitor cell. The values of equivalent series resistance (ESR) (8–9 Ω) and efficiency (100–98%) were found to be independent of the cycle number with an excellent retention capacity of 83%. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41711.     

Electrical properties of poly(phenylene sulfide)/multiwalled carbon nanotube composites prepared by simple mixing and compression

Poly(phenylene sulfide) (PPS)/multiwalled carbon nanotubes (MWNTs) conductive composites were prepared through the simple mixing of PPS granules with MWNT powder and subsequent compression. The electrical properties as a function of MWNT loading clearly showed a low percolation threshold of about 0.22 vol % and a high critical exponent value of 3.55 for composites prepared by this method. A comparison study with composites prepared via melt mixing was also carried out, where a random dispersion of MWNTs was achieved. There existed a striplike morphology of MWNTs in the PPS matrix and MWNTs were selectively located in strips caused by compression. The effects of temperature and pressure on the conductivity of the PPS/MWNT composites as prepared via simple mixing and compression are discussed. In addition, the conductivity also showed a dependence on the flow direction of the compression, with higher conductivity in the direction parallel to the flow direction than in the direction perpendicular to the flow direction. So the relationship of the processing and morphological properties was investigated in detail. The possible conductive mechanisms of conventional melt blending and preparation via sample mixing and compression are also discussed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Improved electrochemical performances of polyaniline by graphitized mesoporus carbon: Hybrid electrode for supercapacitor

In this work, graphitized mesoporus carbon (GMC) was used to increase the specific capacitance and cycle stability of polyaniline (PANI). Hybrid material of polyaniline‐graphitized mesoporus carbon (GMCP) was prepared by in situ chemical polymerization of aniline in presence of sulphuric acid using ammonium persulfate oxidant with various amounts of GMC. Formation of hybrid sample was confirmed from X‐ray diffraction, and the composite sample was stable up to 250°C. Morphology, crystalline nature, and electrochemical performance of GMCP were compared with that of its individual components, GMC and PANI. GMC showed particle morphology and PANI showed nanofiber morphology. GMCP2 composite showed nanofibrous form of PANI grown on GMC (spherical form) along with PANI nanofibers. Higher crystallinity was obtained for GMCP than that of PANI. Cycling stability of GMCP2 was carried up to 12,000 cycles at 1200 W kg^?1 and the retention capacitance was 66% of its original capacitance of 243 F g^?1. With the same power density, GMC showed less capacitance value of 53 F g^?1 with 92% retention and PANI showed capacitance of 187 F g^?1 and it underwent 1500 cycles only. Higher supercapacitor performance was obtained for GMCP composite compared to that of its components, PANI and GMC. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42540.     

Chemical evaluation of composites natural rubber/carbon black/leather tannery projected to antistatic flooring

In this study the composites which are commonly called NR/CB/Leather were developed in order to apply them as antistatic flooring and coating. They were developed using vulcanized natural rubber, carbon black to add an electric conduction property and industrial leather waste. The leather industrial waste was micronized and added to the rubber matrix in proportions of 60 and 80 phr using an opened mixing cylinder according to ASTM D 3182 standard. The composites were exposed to the sanitizing agents, (i) bleach and (ii) disinfectant, aiming to simulate a real cleaning context, and to meet the health standards of the Brazilian Ministry of health. Physical‐chemical and microbiological evaluations were carried out to determine the structural and chemical stabilities of the composites. After this, low water absorption level (<1.5%), immobilization and low chromium oxide level (<1.5), pH within the neutrality rate and an excellent resistance to microbiological contamination were identified for the composites. Thus, from a physical‐chemical perspective, the composites NR/CB/Leather displayed suitable properties and potential for application as antistatic flooring and coatings. Besides using leather industrial waste in their production, their manufacture can boost this industrial sector economically and, consequently, promote a reduction in environmental impact. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43618.