Organomodified montmorillonite as filler in natural and synthetic rubber

The filler action of dodecylamine (12C) intercalated montmorillonite (MNT) referred to as organomodified montmorillonite (12C‐MNT) up to 4 wt % on natural rubber (NR) and styrene butadiene rubber (SBR) was studied and findings were compared with respect to the unmodified Na‐MNT. X‐ray analysis was used to calculate the interchain separation (R and R′), degree of crystallinity (X_c), and distortion factor (k). It is noted that R and R′ showed the opposite trend, whereas X_c as well as k showed overall increasing trend with an increasing amount of 12C‐MNT on both NR and SBR. For Na‐MNT (1 wt %) filled NR and SBR, the corresponding magnitude of R and R ′ and X_c showed nearly no change, whereas k_c increased significantly. The crosslinking density (v_c) does not show any significant changes in NR, whereas for SBR, it increases with increasing 12C‐MNT as filler. Interestingly, in the case of 1 wt % pure Na‐MNT used as filler for both NR and SBR, v_c was lower compared to the virgin rubbers. Both swelling index (s_i) and sol fraction (Q) do not show any significant variation for NR composites, whereas these decrease for SBR composites with increasing concentration of 12C‐MNT filler. On the contrary, NR and SBR with 1 wt % of Na‐MNT filler show greater magnitude of s_i and Q corresponding to the pure ones. Measurements of mechanical properties showed a significant increase in tensile strength and elongation at break for NR‐12C‐MNT (4 wt %) when compared with either virgin NR. In addition, modulus at the elongation at 100 and 200% in general increases with increasing loading of 12C‐MNT filler in NR. Similar observations were also noted in the case of SBR. Interestingly, when only pure Na‐MNT is used as filler, the strength of NR and SBR decreases drastically. Scanning electron microscopic studies were also to used support the mechanical behavior of NR‐12MNT and SBR‐12CMNT composites. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3583–3592, 2004     

A novel grafting‐modified waste rubber powder as filler in natural rubber vulcanizates

Polycardanol was synthesized from cardanol, paraformaldehyde, p‐toluenesulfonic acid, phosphoric acid (H₃PO₄), and phosphorus pentoxide (P₂O₅) via a two‐step process. Results indicated that polycardanol is an acid with high molecular weight and can be self‐crosslinked at high temperature. A modified WRP (MWRP) grafted by long chain can be obtained from the reaction between WRP and polycardanol. The sulfur content of MWRP is 0.27%, which is lower than that of WRP by 0.47%. The oxygen content of MWRP is higher by 13% than that of WRP. The phosphorus content of MWRP reaches 5.25%. The water contact angle of MWRP is 91.5°, whereas that of WRP is 123.7°. The properties of the WRP/NR and MWRP/NR composites were also investigated. MWRP/NR possesses higher tensile strength than WRP/NR because of the enhanced interfacial interaction between MWRP and the NR matrix. Post‐treatment is also conducive for MWRP/NR to improve its tensile strength at high MWRP content. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42993.     

Novel CNC/silica hybrid as potential reinforcing filler for natural rubber compounds

This work describes the development of a low-density, renewable, and high reinforcing filler for natural rubber (NR) compounds. The cellulose nanocrystal (CNC)-based hybrid filler was synthesized by decorating the surface of CNCs with silica using a simple and efficient coprecipitation method. The properties of the prepared hybrid were investigated by field emission scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction, nitrogen physisorption measurements, and Thermogravimetric analysis. Then, the prepared hybrid was incorporated in NR using two different approaches, namely, dry mixing and coprecipitation. The dynamic and tensile mechanical properties of the hybrid/NR compounds were evaluated indicating that: the coprecipitation method was found much more effective for homogeneous dispersion and the CNC/silica hybrid provided quite higher reinforcement to NR than reference silica; however, much lower density of the final compounds was obtained. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48332.     

Possible use of ultra‐fine acrylonitrile butadiene rubber powder as filler in natural rubber vulcanizates

Possible use of ultra‐fine acrylonitrile butadiene rubber powder (UFNBRP) as a filler for natural rubber (NR) was investigated. The UFNBRP was added into NR at various concentrations, and the compound properties were determined. It is found that, with increasing UFNBRP loading, the compound viscosity is increased, whereas both scorch time and optimum curing time are significantly reduced. The results also reveal that UFNBRP has negative effect not only on crosslink density but also on most mechanical properties of the vulcanizate, such as tensile strength, tear strength, compression set, and abrasion resistance. The deterioration of these mechanical properties is thought to arise mainly from the combined effect of large phase size of the dispersed UFNBRP and low interfacial adhesion taking place from the polarity difference between UFNBRP and NR. Interestingly, it is found that, after aging, UFNBRP could promote postcuring phenomenon leading to increases of both relative 100% modulus and relative tensile strength. Oil resistance is also found to improve considerably with increasing UFNBRP loading. This improvement is mainly attributed to the dilution effect, i.e., the higher the UFNBRP loading, the lower the NR portion and, thus, the greater the oil resistance of the vulcanizate. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Development and characterization of graphitic carbon nitride as nonblack filler in natural rubber composites

A new type of elastomeric composite containing natural rubber (NR) and graphitic carbon nitride (g-C₃N₄) has been successfully prepared with the reinforced property. The reinforcing effect of g-C₃N₄ in NR composites was examined by cure, mechanical, morphological, and swelling studies. Besides, epoxidized NR with 50-mol % epoxy level (ENR-50) was used as a compatibilizer to enhance the hydrophilic g-C₃N₄ filler capacity for hydrophobic NR composites. At the same filler load level, the mechanical properties of NR/g-C₃N₄ composites, such as tensile strength and tensile modulus, were consistently increased with increased ENR-50 content. To note, the ENR compatibilized composites have shown better-reinforced performance, which has been attributed to the hydrogen bonding interactions between the uncondensed amine groups in g-C₃N₄ and the polar groups in ENR. We believe that these newly prepared NR composites based on g-C₃N₄ as nonblack filler and ENR-50 as compatibilizer can find potential applications in modern day rubber research. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48136.     

The behavior of dithiocarbimate derivative as safety accelerator of natural rubber compounds

A conventional vulcanization system containing tetrabutylammonium bis(4‐methylphenyldithiocarbimato)zincate(II) (ZNIBU) was used for curing of natural rubber (NR) compounds. Rheometric (t_s1, t₉₀, and CRI) and mechanical properties, such as tensile and tear strengths and modulus at 300%, were measured to evaluate the acceleration potential of ZNIBU. Commercial accelerators (TMTD, MBTS, and CBS) and a binary system CBS/ZNIBU were also tested for comparison purposes. It was observed that ZNIBU alone does not give either safe scorch time or cure rates appropriate for industrial applications. Nevertheless, mechanical properties are comparable to those given by the other accelerators used. As for the binary system, positive synergistic effects can be found in tear strength and modulus of NR vulcanizates. Besides, ZNIBU does not contribute for the formation of nitrosamines in the vulcanization process. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of a natural magnesium silicate treated with a new coupling agent on the properties of ethylene–propylene–diene rubber compounds

The behavior of sepiolite (magnesium silicate with a microfibrillar morphology) as a filler in ethylene–propylene–diene compounds was studied. A new coupling agent, meta‐isopropenyl dimethyl benzyl isocyanate, was used. The effect of the filler modified by meta‐isopropenyl dimethyl benzyl isocyanate on the physical properties was improved with respect to other fillers and commercial silane coupling agents under the same conditions. In addition to a smoother surface, the flow behavior of compounds filled with sepiolite, on account of its fibrous morphology, was better than that obtained with other fillers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1489–1493, 2004     

Effects of coagulation processes on properties of epoxidized natural rubber

The epoxidized natural rubber (ENR) with epoxy group contents of 48.4% were coagulated with ethanol and steam and the structures, processing performances, antioxidative behaviors, cure characteristics, and dynamic mechanical properties were analyzed using infrared spectroscopy, rubber processing analyzer, thermogravimetric analyzer, rheometer, and dynamic thermomechanical analyzer, respectively. The results indicate that the ENR coagulated with ethanol (ENR‐e) exhibits a compact structure and the contents of residual low‐molecular‐weight matters are higher than those of unconsolidated ENR coagulated with steam (ENR‐s). Therefore, the processing performance and antioxidative behavior as well as the curing characteristics of ENR‐e compound are poorer than those of ENR‐s. Although the mechanical properties and wet skid resistance of ENR‐s vulcanizate are poorer than those of ENR‐e, the heat build‐up or rolling resistance of ENR‐s is better than that of ENR‐e. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Utilization of bowstring hemp fiber as a filler in natural rubber compounds

The cure characteristics and physicomechanical properties of natural rubber (standard Nigerian rubber) vulcanizates filled with the fiber of bowstring hemp (Sansevieria liberica) and carbon black were investigated. The results showed that the scorch and cure times decreased, whereas the maximum torques increased, with increasing filler loadings for both bowstring hemp fiber and carbon black filled vulcanizates. The tensile strength of both bowstring hemp fiber and carbon black filled vulcanizates increased to a maximum at a 40 phr filler concentration before decreasing. The elongation at break and rebound resilience decreased, whereas the modulus, specific gravity, abrasion resistance, and hardness increased, with increasing filler contents. The carbon black/natural rubber vulcanizates had higher tensile strength, which was about 1.5 times that of bowstring hemp fiber/natural rubber vulcanizates. This superiority in the tensile strength was probably due to the higher moisture content and larger particle size of the bowstring hemp fiber. However, the bowstring hemp fiber/natural rubber vulcanizates showed superior hardness. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Use of rice husk ash as filler in natural rubber vulcanizates: In comparison with other commercial fillers

Rice husk ash is mainly composed of silica and carbon black remaining from incomplete combustion. Both silica and carbon black have long been recognized as the main reinforcing fillers used in the rubber industry to enhance certain properties of rubber vulcanizates, such as modulus and tensile strength. In this study, two grades of rice husk ash (low‐ and high‐carbon contents) were used as filler in natural rubber. Comparison was made of the reinforcing effect between rice husk ashes and other commercial fillers such as talcum, china clay, calcium carbonate, silica, and carbon black. Fourier transform infrared spectroscopy (FTIR) analysis was employed to study the presence of functional groups on the ash surface. The effect of silane coupling agent, bis(3‐triethoxysilylpropyl)tetrasulfane (Si‐69), on the properties of ash‐filled vulcanizates was also investigated. It was found that both grades of rice husk ash provide inferior mechanical properties (tensile strength, modulus, hardness, abrasion resistance, and tear strength) in comparison with reinforcing fillers such as silica and carbon black. However, the mechanical properties of the vulcanizates filled with rice husk ash are comparable to those filled with inert fillers. The addition of silane‐coupling agent has little effect on the properties of the ash‐filled vulcanizates. This is simply due to the lack of silanol groups on the ash surface. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2485–2493, 2002     

Studies in the utilization of agricultural waste products as filler in natural rubber compounds

Natural rubber samples were filled with agricultural waste products (cocoa pod husks and rubber‐seed shell) at 50 phr, mixed on a two‐roll mill, and cured using the semiefficient vulcanization system. The physicomechanical properties, tensile strength, modulus at 100% elongation, elongation at break, hardness, abrasion resistance, flex fatigue and compression set, of the agricultural waste products‐filled natural rubber compounds were determined and compared with the values obtained for vulcanisates filled with commercial carbon black (HAF N330). The effect of blending the raw and carbonized agricultural waste products with the commercial grade N330 carbon black on the physicomechanical properties of the natural compounds was studied. It was found that the raw agricultural waste products were ineffective compared with N330 carbon black as reinforcing filler for natural rubber compound mixes and could be classified as semireinforcing fillers. Blends containing up to 40 wt % of the raw agricultural waste products and more than 60 wt % of the carbonized waste products gave natural rubber compounds with comparable physciomechanical properties with compound obtained with N330 carbon black. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2561–2564, 2006     

Agricultural proteins as multifunctional additives in ZnO-free synthetic isoprene rubber vulcanizates

Corn zein and wheat gliadin protein are compounded into synthetic cis-1,4-polyisoprene rubber (IR) and sulfur-cured in a zinc oxide (ZnO)-free system. The curing kinetics and mechanical and morphological properties are compared to a ZnO-activated or carbon black (CB)-reinforced cure system. The proteins provide reversion resistance and reinforcement to IR at filler loadings as low as 1 part per hundred rubber (phr). The zein-IR composites exhibit higher moduli, better filler–matrix adhesion, and less filler agglomeration/migration than gliadin-IR because zein is more chemically compatible with IR. The gliadin-IR composites have a lower percent set and hysteresis, indicating the formation of an elastic restoring gliadin network. Optimal properties are achieved at 2-phr gliadin and 4-phr zein. At gliadin loading >2 phr and zein loading >4 phr, the protein domain size increases and mechanical properties deteriorate. At equal filler loading, property improvements over CB-IR are observed for one or both proteins. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48141.     

Enhancement of electromechanical properties of natural rubber by adding barium titanate filler: An electro-mechanical study

Natural rubber is one of the most potential electro-active polymers for sensors, actuators, and energy harvesting applications. Enhancing the characteristic properties of polymers by reinforcing with fillers that possess multifunctional attributes have attracted considerable attention. In the present study, barium titanate reinforced natural rubber composite is prepared by using two-roll mill mixing. Afterwards, mechanical, electrical, and electromechanical properties of the composites are extensively analyzed by reinforcing different amounts of barium titanate into the matrix of natural rubber. The fabricated dielectric composite shows excellent properties such as high dielectric constant, low dielectric losses, high dielectric breakdown strength, and extreme stretchability. It is observed that as the filler loading reaches the value of 11 parts per hundred rubber (phr), maximum agglomeration of the particles occurs. Maximum stretchability and highest ratio of dielectric constant to elastic modulus are obtained at 8 phr of barium titanate fillers and at the loading, a maximum actuation strain of 11.24% is achieved. This study provides a simple, economical, and effective method for preparing enhanced mechanical, electrical, and electromechanical properties of natural rubber composites, facilitating the wide applications of dielectric materials as actuators and generators.     

Organomodified kaolin as a reinforcing filler for natural rubber

China clay (kaolin) has been modified with sodium salt of rubber seed oil (SRSO). SRSO was characterized using X‐ray diffraction (XRD), infrared spectroscopy (FTIR), and differential thermal analysis (DTA). XRD of the unmodified and SRSO‐modified kaolins showed an increase in the d‐(001) spacing of kaolin platelets from 7.15 to 14 Å. FTIR spectroscopy indicated possible grafting of the organic moiety of rubber seed oil (RSO) onto the clay surface. DTA of the SRSO‐modified kaolin indicated that the SRSO is more strongly bound in a constraint environment within the lamellae of kaolin. Natural rubber (NR) mix containing 10 phr of SRSO‐modified kaolin was found to cure faster than that of a similar mix containing unmodified kaolin. NR vulcanizates containing SRSO‐modified kaolin showed considerable increase in tensile modulus, tensile strength, and elongation at break indicating its potential as an organomodified nanofiller. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Length scale dependent deformation in natural rubber

Strong length scale dependent deformation has been previously observed in the elastomer polydimethylsiloxane by indentation type experiments at micro‐ to nanometer length scales with a sharp conical tip. To examine if other nonsilicone based elastomers exhibit similar length scale dependent deformation behavior, natural rubber has been chosen in this study. Performing indentation type tests with a nanoindentation system, the universal hardness and the elastic modulus are determined at different probing depths ranging from about 90 to 5 μm to characterize length scale dependent deformation behavior in natural rubber. The testing with a Berkovich tip resulted in an amazing increase in the universal hardness with decreasing probing depth indicating that the deformation mechanisms at the micrometer length scales are significantly different as compared to those at the macroscopic length scales. The observed length scale dependent deformation is associated with an increase in rotation gradients with decreasing probing depth. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42683.     

Fly ash particles and precipitated silica as fillers in rubbers. I. Untreated fillers in natural rubber and styrene–butadiene rubber compounds

In this study, we investigated the effects of untreated precipitated silica (PSi) and fly ash silica (FASi) as fillers on the properties of natural rubber (NR) and styrene–butadiene rubber (SBR) compounds. The cure characteristics and the final properties of the NR and SBR compounds were considered separately and comparatively with regard to the effect of the loading of the fillers, which ranged from 0 to 80 phr. In the NR system, the cure time and minimum and maximum torques of the NR compounds progressively increased at PSi loadings of 30–75 phr. A relatively low cure time and low viscosity of the NR compounds were achieved throughout the FASi loadings used. The vulcanizate properties of the FASi‐filled vulcanizates appeared to be very similar to those of the PSi‐filled vulcanizates at silica contents of 0–30 phr. Above these concentrations, the properties of the PSi‐filled vulcanizates improved, whereas those of the FASi‐filled compounds remained the same. In the SBR system, the changing trends of all of the properties of the filled SBR vulcanizates were very similar to those of the filled NR vulcanizates, except for the tensile and tear strengths. For a given rubber matrix and silica content, the discrepancies in the results between PSi and FASi were associated with filler–filler interactions, filler particle size, and the amount of nonrubber in the vulcanizates. With the effect of the FASi particles on the mechanical properties of the NR and SBR vulcanizates considered, we recommend fly ash particles as a filler in NR at silica concentrations of 0–30 phr but not in SBR systems, except when improvement in the tensile and tear properties is required. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 2119–2130, 2004     

Experimental analysis of viscoelastic properties in carbon black‐filled natural rubber compounds

Processability and viscoelastic properties of natural rubber (NR) compounds filled with different carbon black loadings and types were investigated with the use of a steady shear rheometer, namely, the Mooney viscometer, and an oscillatory rheometer, namely, the Rubber Process Analyser (RPA2000). It was found that the type and amount of carbon black strongly influence the viscoelastic properties of rubber compounds. Both the dilution effect and filler transient network are responsible for the viscoelastic properties, depending on the vulcanization state. In the case of uncured compounds, the damping factor of the uncured NR decreases with increasing black loading. This is attributed to the reduction of mobilized rubber content in the compound (or the dilution effect). However, in the case of the cured NR vulcanizates, the filler transient network is the dominant factor governing the damping factor of the vulcanizate. With increasing black loading, the damping factor of the vulcanizate clearly increases. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 2197–2203, 2005     

Role of geopolymer as a cure activator in sulfur vulcanization of epoxidized natural rubber

Geopolymer (GP) was synthesized and used as activators in sulfur vulcanization of epoxidized natural rubber (ENR). Influences of GP on cure characteristics, crosslink density, mechanical, thermal, and morphological properties were investigated and compared to the conventional rubber formulation with ZnO activator. The ZnO is a hazardous chemical for the environment and has proclaimed that its application in rubber technology should be reduced and controlled. It was found that the GP-activated ENR compounds showed significantly higher vulcanization rate than cases with the conventional ZnO compound. This was indicated by the GP activated compounds having shorter scorch time, cure times, and lower activation energy but higher cure rate index (CRI). Also, the GP activated ENR compounded with stearic acid exhibited the highest conversion. This matches well the highest torque difference and crosslink density, observed by temperature scanning stress relaxation (TSSR) and swelling measurements. Furthermore, the GP-activated vulcanizate had better thermal stability than the ZnO-activated ENR material. In addition, the GP-activated ENR vulcanizate with stearic acid exhibited high 100% moduli, tensile strength, and hardness. This proves that GP has a high potential for use as activators in sulfur vulcanization of rubber compounds, as an alternative to the conventional ZnO. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48624.     

Physical and mechanical properties of poly(methyl methacrylate)‐grafted natural rubber synthesized by methyl methacrylate photopolymerization initiated by N,N‐diethyldithiocarbamate functions previously created on natural rubber chains

Well‐defined poly(methyl methacrylate) (PMMA)‐grafted natural rubbers (NRs) were prepared to study the structure–property relationships. Syntheses were achieved by the photopolymerization of methyl methacrylate initiated by N,N‐diethyldithiocarbamate groups created beforehand in side positions on the NR chains. With this procedure, good control of the graft density and PMMA content could be obtained. Thermal, morphological, and mechanical properties of NR‐g‐PMMA copolymers were studied as a function of the NR/PMMA composition and graft density. NR‐g‐PMMAs containing 15–80% grafted PMMA showed characteristics of heterogeneous materials (characterized by two glass‐transition temperatures, those of PMMA and NR, in differential scanning calorimetry). Under these conditions, they developed the morphology of thermoplastic elastomers with PMMA nodules dispersed in the rubber matrix when the PMMA content was near 20%; conversely, they developed the morphology of softened thermoplastics with rubber nodules dispersed in PMMA when the PMMA content was near 80%. Graft copolymers containing about 20% PMMA remained essentially rubbery, but they were already different from pure NR. On the other hand, the thermal stability of NR wash improved after the introduction of PMMA grafts onto NR chains. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effects of palm ash loading and maleated natural rubber as a coupling agent on the properties of palm‐ash‐filled natural rubber composites

Natural rubber composites were prepared by the incorporation of palm ash at different loadings into a natural rubber matrix with a laboratory‐size two‐roll mill (160 × 320 mm²) maintained at 70 ± 5°C in accordance with the method described by ASTM D 3184–89. A coupling agent, maleated natural rubber (MANR), was used to improve the mechanical properties of the natural rubber composites. The results indicated that the scorch time and cure time decreased with increasing filler loading, whereas the maximum torque exhibited an increasing trend. Increasing the palm ash loading increased the tensile modulus, but the tensile strength, fatigue life, and elongation at break decreased. The rubber–filler interactions of the composites decreased with increasing filler loading. Scanning electron microscopy of the tensile fracture surfaces of the composites and rubber–filler interaction studies showed that the presence of MANR enhanced the interfacial interaction of the palm ash filler and natural rubber matrix. The presence of MANR also enhanced the tensile properties and fatigue life of palm‐ash‐filled natural rubber composites. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008