Solidification of welded SiC–ZrB2–ZrC ceramics

A silicon carbide‐based ceramic, containing 50 vol% SiC, 35 vol% ZrB₂, and 15 vol% ZrC was plasma arc welded to produce continuous fusion joints with varying penetration depth. The parent material was preheated to 1450°C and arc welding was successfully implemented for joining of the parent material. A current of 138 A, plasma flow rate of ~1 L/min or ~0.5 L/min, and welding speed of ~8 cm/min were utilized for repeated joining, with full penetration fusion zones along the entire length of the joints. Solidification was determined to occur through the crystallization of β‐SiC (3C), then the simultaneous solidification of SiC and ZrB₂, and lastly through the simultaneous solidification of SiC, ZrB₂, and ZrC through a ternary eutectic reaction. The ternary eutectic composition was determined to be 35.3 ± 2.2 vol% SiC, 39.3 ± 3.8 vol% ZrB₂, and 25.4 ± 3.0 vol% ZrC. A dual fusion zone microstructure was always observed due to convective melt pool mixing. The SiC content at the edge of the fusion zone was 57 vol%, while SiC content at the center of the fusion zone was 42 vol% although the overall SiC content was still nominally 50 vol% throughout the entire fusion zone.     

Anisotropy of functional properties of SiC composites with GNPs,GO and in-situ formed graphene

This paper reports on anisotropy of functional properties of different silicon carbide-graphene composites due to preferential orientation of graphene layers during sintering. Dense silicon carbide/graphene nanoplatelets (SiC/GNPs) and silicon carbide/graphene oxide (SiC/GO) composites were sintered in the presence of yttria (Y₂O₃) and alumina (Al₂O₃) sintering additives at 1800 °C in vacuum by the rapid hot pressing (RHP) technique. It is found that electrical conductivity of SiC/GNPs and SiC/GO composites increases significantly in the perpendicular direction to the RHP pressing axis, reached up to 1775 S/m in the case of SiC/GO (for 3.15 wt.% of rGO). Also, thermal diffusivity was found to increase slightly by the addition of GNPs in the SiC/GNPs composites in the perpendicular direction to the RHP pressing axis. But, in the parallel direction, the addition of GNPs showed a negative effect. The formation of graphene domains was observed in reference sample SiC-Y₂O₃-Al₂O₃ sintered by RHP, without any addition of graphene. Their presence was confirmed indirectly by increasing electrical conductivity about three orders of magnitude in comparison to the reference sample sintered by conventional hot press (HP). Raman, SEM and TEM analysis were used for direct evidence of presence of graphene domains in RHP reference sample.     

Densification,microstructure, and mechanical properties of ZrC–SiC ceramics

ZrC–SiC ceramics were fabricated by high-energy ball milling and reactive hot pressing of ZrH₂, carbon black, and varying amounts of SiC. The ceramics were composed of nominally pure ZrC containing 0 to 30 vol% SiC particles. The relative density increased as SiC content increased, from 96.8% for nominally pure ZrC to 99.3% for ZrC-30 vol% SiC. As SiC content increased from 0 to 30 vol%, Young's modulus increased from 404 ± 11 to 420 ± 9 GPa and Vickers hardness increased from 18.5 ± 0.7 to 23.0 ± 0.5 GPa due to a combination of the higher relative density of ceramics with higher SiC content and the higher Young's modulus and hardness of SiC compared to ZrC. Flexure strength was 308 ± 11 MPa for pure ZrC, but increased to 576 ± 49 MPa for a SiC content of 30 vol%. Fracture toughness was 2.3 ± 0.2 MPa·m^1/2 for pure ZrC and increased to about 3.0 ± 0.1 MPa·m^1/2 for compositions containing SiC additions. The combination of high-energy ball milling and reactive hot pressing was able to produce ZrC–SiC ceramics with sub-micron grain sizes and high relative densities with higher strengths than previously reported for similar materials.     

Microstructure and mechanical properties of boron carbide/graphene nanoplatelets composites fabricated by hot pressing

In this study, boron carbide (B₄C)-graphene nanoplatelets (GNPs) composites, with enhanced strength and toughness, were fabricated by hot pressing at 1950 °C under a pressure of 30 MPa for 1 h. Microstructure analysis revealed that the GNPs are homogenously dispersed within the B₄C matrix. Raman spectroscopy and electron microscopy showed the orientation of the GNPs in the composites. The effects of the amount of GNPs on the microstructure and mechanical properties of the composites were also investigated. The optimal mechanical properties were achieved using 1 wt% GNPs. The relative density, Vickers hardness, flexure strength, and fracture toughness of the B₄C-GNPs composite ceramic were found to be 99.12%, 32.8 GPa, 508 MPa, and 4.66 MPa m^1/2, respectively. The main toughening mechanisms included crack deflection in three dimensions, GNPs pull-out, and crack bridging. The curled and semi-wrapped GNPs encapsulated individual B₄C grains to resist GNPs pull-out and to deflect propagating cracks.     

Microstructure and toughening mechanisms of Al2O3/(W,Ti)C/graphene composite ceramic tool material

To toughen the Al₂O₃ matrix ceramic materials, Al₂O₃/(W, Ti)C/graphene multi-phase composite ceramic materials were fabricated via hot pressing. The effects of the graphene nanoplates (GNPs) content on microstructure and mechanical properties were investigated. Results showed that the fracture toughness and flexural strength of the composite added with just 0.2?wt% GNPs were markedly improved by about 35.3% (~ 7.78?MPa?m^1/2) and 49% (~ 608.54?MPa) respectively compared with the specimens without GNPs while the hardness was kept about 24.22?GPa. However, the mechanical properties degrade with the further increase of GNPs’ content owing to the increased defects caused by agglomeration of GNPs. Synergistic toughening effects of (W, Ti)C and GNPs played an essential role in improving the fracture toughness of composites. By analyzing the microstructures of fractured surface and indentation cracks, besides GNPs pull-out, crack deflection, crack bridging, crack branching and crack arrest, new toughening mechanisms such as break of GNPs and crack guiding were also identified. Furthermore, interface stress can be controlled by means of stagger distributed strong and weak bonding interfaces correlated with the distribution of GNPs.     

Mechanical properties of silicon carbide—in situ zirconium carbonitride composites

SiC–Zr₂CN composites were fabricated by conventional hot pressing from β-SiC and ZrN powders with 2 vol% equimolar Y₂O₃–Sc₂O₃ as a sintering additive. The effects of the ZrN addition on the room-temperature (RT) mechanical properties and high-temperature flexural strength of the SiC–Zr₂CN composites were investigated. The fracture toughness gradually increased from 4.2 ± 0.3 MPa·m^1/2 for monolithic SiC to 6.3 ± 0.2 MPa·m^1/2 for a SiC–20 vol% ZrN composite, whereas the RT flexural strength (546 ± 32 MPa for the monolithic SiC) reached its maximum of 644 ± 87 MPa for the SiC–10 vol% ZrN composite. The monolithic SiC had improved strength at 1200°C, whereas the SiC–Zr₂CN composites could not retain their RT strengths at 1200°C. The typical flexural strength values of the SiC–0, 10, and 20 vol% ZrN composites at 1200°C were 650 ± 53, 448 ± 31, and 386 ± 19 MPa, whereas their RT strength values were 546 ± 32, 644 ± 87, and 528 ± 117 MPa, respectively.     

Interface microstructure and mechanical properties of Ni–Co–P alloy coatings modified carbon fibres reinforced 7075Al matrix composites

To optimize interface microstructure between 7075Al matrix and CFs, Ni–Co–P multi-component alloy coatings coated carbon fibres were prepared by electroless plating firstly and then Ni–Co–P coated CFs reinforced 7075Al matrix composites (CF/Al(Ni–Co–P)) with high relative density were fabricated by hot pressing sintering process. After modification of Ni–Co–P coatings, Al–Co–Ni Intermetallic compounds were formed stably between matrix and reinforcement because of the smaller mixing enthalpy values of Al–Co, Al–Ni and Co–Ni, which not only restrained the generation of Al₄C₃ but also improved interfacial bonding strength. Yield strength and ultimate tensile strength of CF/Al(Ni–Co–P) composites with 30 vol% CFs had maximum improvement compared with CF/Al(U) composites than other composites reinforced by 10 vol%, 20 vol% and 30 vol%CFs, which is up to 305.8 MPa and 668.7 MPa respectively, and the fracture mode of composites from accumulation fracture to non-accumulation fracture as the existence of Ni–Co–P coatings.     

Effect of ZrB2 content on the densification,microstructure, and mechanical properties of ZrC-SiC ceramics

ZrC ceramics containing 30 vol% SiC-ZrB₂ were produced by high-energy ball milling and reactive hot pressing. The effects of ZrB₂ content on the densification, microstructure, and mechanical properties of ceramics were investigated. Fully dense ceramics were achieved as ZrB₂ content increased to 10 and 15 vol%. The addition of ZrB₂ suppressed grain growth and promoted dispersion of the SiC particles, resulting in fine and homogeneous microstructures. Vickers hardness increased from 23.0 ± 0.5 GPa to 23.9 ± 0.5 GPa and Young’s modulus increased from 430 ± 3 GPa to 455 ± 3 GPa as ZrB₂ content increased from 0 to 15 vol%. The increases were attributed to a combination of the higher relative density of ceramics with higher ZrB₂ content and the higher Young’s modulus and hardness of ZrB₂ compared to ZrC. Indentation fracture toughness increased from 2.6 ± 0.2 MPa⋅m^1/2 to 3.3 ± 0.1 MPa⋅m^1/2 as ZrB₂ content increased from 0 to 15 vol% due to the increase in crack deflection by the uniformly dispersed SiC particles. Compared to binary ZrC-SiC ceramics, ternary ZrC-SiC-ZrB₂ ceramics with finer microstructure and higher relative densities were achieved by the addition of ZrB₂ particles.     

Postsintering Hot Isostatic Pressing of Ceria-Doped Tetragonal Zirconia/Alumina Composites in an Argon–Oxygen Gas Atmosphere

Ceria-doped tetragonal zirconia (Ce-TZP)/alumina (Al₂O₃) composites were fabricated by sintering at 1450° to 1600°C in air, followed by hot isostatic pressing (postsintering hot isostatic pressing) at 1450°C and 100 MPa in an 80 vol% Ar–20 vol% O₂ gas atmosphere. Dispersion of Al₂O₃ particles into Ce-TZP was useful in increasing the relative density and suppressing the grain growth of Ce-TZP before hot isostatic pressing, but improvement of the fracture strength and fracture toughness was limited. Postsintering hot isostatic pressing was useful to densify Ce-TZP/Al₂O₃ composites without grain growth and to improve the fracture strength and thermal shock resistance.     

Synergetic effects of SiC and Csf in ZrB2-based ceramic composites. Part I: Densification behavior

The effects of processing variables on densification behavior of hot pressed ZrB₂-based composites, reinforced with SiC particles and short carbon fibers (C_sf), were studied. A design of experiment approach, Taguchi methodology, was used to investigate the characteristics of ZrB₂–SiC–C_sf composites concentrated upon the hot pressing parameters (sintering temperature, dwell time and applied pressure) as well as the composition (vol% SiC/vol% C_sf). The analysis of variance recognized the sintering temperature and SiC/C_sf ratio as the most effective variables on the relative density of hot pressed composites. The microstructural investigations showed that C_sf can act as a sintering aid and eliminate the oxide impurities (e.g. B₂O₃, ZrO₂ and SiO₂) from the surfaces of raw materials. A fully dense composite was achieved by adding 10 vol% C_sf and 20 vol% SiC to the ZrB₂ matrix via hot pressing at 1850 °C for 30 min under a pressure of 16 MPa. Moreover, the in-situ formation of interfacial ZrC, which also improves the sinterability of ZrB₂-based composites, was studied by energy-dispersive X-ray spectroscopy analysis and verified thermodynamically.     

Polypropylene/poly(lactic acid)/carbon nanotube semi-biodegradable nanocomposites: The effect of sequential mixing approach and compatibilization on morphology,rheology and electrical conductivity

Semi-biodegradable polypropylene (PP)/poly(lactic acid) (PLA) (50:50 vol%) blend loaded with 0.6 vol% of pristine carbon nanotube (CNT) were prepared by melt compounding the components using different sequential mixing strategies: (i) all components together (PP/PLA/CNT); (ii) PP first mixed with CNT (PP@CNT/EVA) and (iii) EVA first mixed with CNT (EVA@CNT/PP). The composites presented co-continuous structure and the CNT selectively localized inside the PP phase or at the interface, regardless the order of the CNT addition into the mixing. These features were confirmed by selective extraction experiments and morphological studies: optical, scanning electron, and transmission electron microscopy. However, the preferential localization at the interface was predicted from wetting coefficient, determined from interfacial energy. Higher electrical conductivity values were achieved by using the one-step mixing approach, were all components were mixed together, whose value of around 10⁻⁴ S/m was achieved by adding 0.6 vol% of CNT to the blend. The compatibilization with polypropylene-g-maleic anhydride increased the melt viscosity of the blend and composite but did not affect the conductivity or the tensile properties of the CNT-based composite.     

化学修饰啤酒酵母菌对铀的吸附特性

以甲醛为交联剂,将胱氨酸修饰到啤酒酵母菌(SC)上,并采用海藻酸钠和明胶固定化,得到一种新型的生物吸附剂——修饰啤酒酵母菌( MSC).通过红外光谱(IR)分别表征了两种吸附剂的结构,考察了其吸附铀的主要影响因素即溶液pH值、吸附时间等.结果表明:MSC细胞表面具有大量吸附铀的基团,MSC和SC吸附铀的最佳条件是:pH...     

High‐performance antistatic ethylene–vinyl acetate copolymer/high‐density polyethylene composites with graphene nanoplatelets coated by polyaniline

Graphene nanoplatelets coated by polyaniline (GNP@PANI) and ethylene–vinyl acetate (EVA) copolymer–high‐density polyethylene (HDPE) were used for the first time to prepare high‐performance antistatic composites through an effective method that combined solution mixing and melt blending. GNP@PANI nanocomposites were fabricated by in situ polymerization to improve the dispersion of graphene nanoplatelets (GNPs) in the EVA–HDPE matrix and the compatibility between the GNPs and the EVA–HDPE matrix. The GNP@PANI nanocomposites and EVA were first prepared as a premix through solution mixing, and then, the premix and HDPE were prepared as highly antistatic composites through melt blending. The dispersion of the GNPs in the EVA–HDPE matrix and the compatibility between the GNPs and the EVA–HDPE matrix were confirmed by field emission scanning electron microscopy and transmission electron microscopy observations. The GNP@PANI–EVA–HDPE composites met the requirements for antistatic materials when the content of the GNP@PANI nanocomposites was 5 wt % with only about 1 wt % GNPs. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45303.     

Fabrication and characterization of B4C–ZrB2–SiC ceramics with simultaneously improved high temperature strength and oxidation resistance up to 1600 °C

B₄C–30 vol% ZrB₂ and B₄C–30 vol% ZrB₂–10 vol% SiC ceramics were prepared using hot pressing, and their room temperature flexural strength, high temperature flexural strength and oxidation behavior were investigated and compared each other. Both room temperature and high temperature flexural strength were improved by adding SiC particles. The oxidation mechanism was also studied, showing the oxidation product of SiC sealed the porosity and cracks, which was helpful to high temperature strength and oxidation resistance improvement.     

Processing and properties of ZrB2-SiC composites obtained by aqueous tape casting and hot pressing

ZrB₂-SiC composites with different SiC content were prepared through aqueous tape casting and hot pressing. The influences of dispersant, SiC content and binder content on the rheological properties of slurries were investigated and the conditions for preparing stable ZrB₂-SiC suspensions were optimized. After tape casting and drying, the green ZrB₂-SiC tapes showed good flexibility, lubricious surface and homogeneous microstructure. The ZrB₂ ceramics could be densified to 97.2% after hot-pressing, while the ZrB₂ containing 20 and 30 vol% SiC ceramics were nearly fully densified (>99%). The sintered ZrB₂-20 vol% SiC ceramic had improved mechanical properties compared with ZrB₂ ceramic. Further increase in SiC content resulted in lower flexural strength and fracture toughness. SEM and TEM showed a fine microstructure with a clear grain boundary. The fracture mode changed from intragranular type for ZrB₂ to both intragranular and intergranular type for ZrB₂-SiC composites.     

Fabrication and properties of reactively hot pressed ZrB2–SiC ceramics

ZrB₂–SiC ceramics with relative densities >99% were fabricated by ‘in situ’ reactive hot pressing from ZrH₂, B₄C and Si. The reaction was studied using two processes, (1) powder reactions at temperatures from 1150 to 1400 °C and (2) reactive hot pressing between 1600 and 1900 °C. The products from the reaction of a 2ZrH₂:1B₄C:1Si molar mixture were ZrB₂, SiC, ZrO₂ and ZrC. Modification of the composition to 2ZrH₂:1.07B₄C:1.16Si resulted in the elimination of the undesired ZrO₂ and ZrC phases. The final composition was approximately ZrB₂–27 vol% SiC with no undesired phases detected by X-ray diffraction, and only low concentrations of B₄C detected by scanning electron microscopy. Elimination of the undesired phases was accomplished by removing surface oxides through chemical reactions at elevated temperatures. Reactively hot pressed samples consisting of ZrB₂ with 27 vol% SiC had a Young's modulus of 508 GPa, a flexure strength of 720 MPa, a fracture toughness of 3.5 MPa m^1/2 and a Vickers’ hardness of 22.8 GPa.     

Microstructure and anisotropic mechanical properties of graphene nanoplatelet toughened biphasic calcium phosphate composite

Graphene nanoplatelets (GNPs) reinforced biphasic calcium phosphate (BCP) composites were prepared by hot pressing (HP). Based on in-depth mechanical test and observation of microstructure, the influence of GNPs on BCP matrix was investigated. A preferred orientation of GNPs occurred during sintering, leading to anisotropic mechanical properties. The mechanical properties of GNPs/BCP composite measured along the direction parallel to the HP direction are higher than those measured along the perpendicular direction. Parallel to the HP direction, the composite containing 1.5 wt% GNPs exhibited the maximun bending strength and fracture toughness of 151.82 MPa and 1.74 MPa m^1/2, about 55% and 76% higher than those of monolithic BCP, respectively. The improvement in mechanical properties was mainly attributable to crack deflection, crack branching, bridging, pullout and fracture of GNPs. Especially GNPs can force crack to propagate not only in two but also in three dimensions.     

Synergetic effects of SiC and Csf in ZrB2-based ceramic composites. Part II: Grain growth

The synergetic effects SiC particles and short carbon fibers (C_sf) as well as hot pressing parameters (sintering temperature, dwell time and applied pressure) on the grain growth of ZrB₂-based composites were investigated. Taguchi methodology was employed for the design of experiments to study the microstructure and grain growth of ZrB₂–SiC–C_sf ceramic composites. Three hot pressing parameters and SiC/C_sf ratio were selected as the scrutinized variables. The sintering temperature and SiC/C_sf ratio were identified by ANOVA as the most effective variables on the gain growth of ZrB₂-based samples. Removal of oxide impurities from the surface of starting particles by the reactant C_sf, not only hindered the extraordinary grain growth of ZrB₂ matrix, but also improved the sinterability of the ceramics. A fully dense ceramic with an average grain size of 8.3 µm was obtained by hot pressing at 1850 °C for 30 min under 16 MPa through adding 20 vol% SiC and 10 vol% C_sf to the ZrB₂ matrix. SEM observations and EDS analysis verified the in-situ formation of ZrC which can restrain the growth of ZrB₂ particles, similar to the role of SiC, by the pinning of grain boundaries as another stationary secondary phase.     

Zirconium diboride laminates for improved damage tolerance at elevated temperatures

The mechanical response was studied for dense laminates containing layers of ZrB₂ (~145 µm) and graphite—10 vol% ZrB₂ (~20 µm). Individual layers were formulated by mixing starting powders with thermoplastic polymers and pressing into sheets. Laminates were produced by stacking and warm pressing the sheets, debinding, and hot pressing at 2050°C, 32 MPa, in Ar. The laminates were fractured at temperatures up to 2000°C in Ar. Laminates exhibited room temperature flexure strength of 260 MPa, increasing to 300 MPa at 1600°C, and then decreasing to 160 MPa at 2000°C. Inelastic work of fracture was 0.6 kJ/m² at room temperature, reached a maximum of 1.3 kJ/m² at 1400°C, and reverted to linear elastic failure at 2000°C. During fracture, cracks were deflected at the interfaces between the strong ZrB₂ layers and the relatively weak C-ZrB₂ layers, which led to an increased inelastic work of fracture by more than an order of magnitude compared to conventional ZrB₂ ceramics. This study demonstrated that laminate architectures are a promising approach for improving the damage tolerance of ZrB₂-based ceramics at elevated temperatures.     

Hot pressing of oxides in the presence of a liquid phase

Conclusions By incorporating certain substances, which, at low temperatures develop a liquid phase, it is possible to prepare by hot pressing at 1000–1300°C high-density (98–99.8% of the theoretical density) products from highly refractory oxides (MgO and Al₂O₃), including their simultaneous synthesis from their compound (Mg Al₂O₄).The role of the liquid phase with this method of hot pressing consists in partially facilitating the grain slip at the initial stages of the process, but mainly in the fact that the liquid phase is a medium through which diffusion occurs, contributing to the densification of the material and its recrystallization. In this case the correspondences between the melting point and the pressing temperature, the structure of the liquid phase, and its composition are decisive.The method of hot pressing highly refractory oxides at low temperatures and in the presence of additives, forming a melt and volatilizing during prolonged subsequent heating, is promising for pressing pure and high purity materials.Translated from Ogneupory, No. 8, pp. 36–40, August, 1971.