Spinning-assist layer-by-layer assembled polysulfonamide membrane for reverse osmosis from naphthalene-1,3,6-trisulfonylchloride and piperazine

Polysulfonamide (PSA), with its chemical stability and acid-resistance, is seen as a potential material for reverse osmosis. However, the present PSA thin film composite membranes fabricated via prevailing interfacial polymerization (IP) approach generally exhibited nonfavored desalination performance. In this work, PSA membrane was assembled via spinning-assist layer-by-layer (sLbL) on a poly(vinyl alcohol) modified polyethersulfone substrate. Fabrication was carried out through sequential interfacial reaction between naphthalene-1,3,6-trisufonylchloride and piperazine by alternately dipping and drying the substrate in two monomer phases. Morphology, chemical composition, surface charge distribution as well as surface hydrophilicity were investigated as a function of repeated cycles. The sLbL assembly approach implemented facile control over membrane properties with well-organized selective layer thickness growth and twofold to threefold reduced surface roughness. As measured from spectroscopic ellipsometry, the sLbL assembled membranes exhibited a linear thickness growth at ~2.72 nm per layer. Performance test indicated that the salt rejection and water flux showed a trade-off pattern with increasing layer number. The PSA membrane with five layers showed a preferable NaCl rejection of 95.7 ± 0.4% with a water flux of 12.4 ± 0.9 L m⁻² h⁻¹ at 10 bar, whereas the IP membrane exhibited only 58% and a 22.12 L m⁻² h⁻¹ flux. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47138.     

Synthesis and characterization of PES/PSF/PEG by immersion precipitation for Mediterranean seawater desalination by FO membrane

In the present study, a simple, inexpensive, nontoxic, and environmentally friendly polyethylene glycol (PEG) polymer was used to enhance the hydrophilicity of the forward osmosis (FO) membrane using various PEG concentrations as a pore forming agent in the casting solution of polyethersulfone/polysulfone (PES/PSF) blend membranes. A nonwoven PES/PSF FO blend membrane was fabricated via the immersion precipitation phase inversion technique. The membrane dope solution was cast on polyethylene terephthalate (PET) nonwoven fabric. The results revealed that PEG is a pore forming agent and that adding PEG promotes membrane hydrophilicity. The membrane with 1 wt% PEG (PEG1) had about 27% lower contact angle than the pristine blend membrane. The PEG1 membrane has less tortuosity (which reduces from 3.4–2.73), resulting in a smaller structure parameter (S value) of 277 μm, due to the presence of open pores on the bottom surface structure, which results in diminished ICP. Using 1 M NaCl as the draw solution and distilled water as the feed solution, the PEG1 membrane exhibited higher water flux (136 L m⁻² h⁻¹) and lower reverse salt flux (1.94 g m⁻² h⁻¹). Also, the selectivity of the membrane, specific reverse salt flux, (J_s/J_w) showed lower values (0.014 g/L). Actually, the PEG1 membrane has a 34.6% higher water flux than the commercial nonwoven-cellulose triacetate (NW-CTA) membrane. By means of varied concentrations of NaCl salt solution (0.6, 1, 1.5, and 2 M), the membrane with 1 wt% PEG showed improved FO separation performance with permeate water fluxes of 108, 136, 142, and 163 L m⁻² h⁻¹. In this work, we extend a promising gate for designing fast water flux PES/PSF/PEG FO blend membranes for water desalination.     

Polyethyleneimine-Mediated Polyamide Composite Membrane with High Perm-Selectivity for Forward Osmosis

Thin-film composite (TFC) membranes comprised of a polyamide (PA) selective layer upon a porous substrate dominate the forward osmosis (FO) membrane market. However, further improvement of perm-selectivity still remains a great challenge. Herein, a polyethyleneimine (PEI) interlayer is intentionally designed prior to interfacial polymerization (IP) to tailor the PA layer, which thus improves the separation performance. The PEI interlayer not only improves the substrate hydrophilicity for adsorbing more diamine monomer and controlling its release rate, but also participates in IP reaction by crosslinking with acyl chloride (TMC). Furthermore, it can decrease the electronegativity of the substrate for decreasing reverse salt diffusion. Consequently, a denser, thinner and smoother PA layer is formed due to the uniform distribution, controllable release of diamine monomer and the extra crosslinking between PEI and TMC. Furthermore, the PA layer becomes more hydrophilic with PEI involvement. As a result, the asprepared TFC membrane exhibits a favorable water flux of 16.1 L m⁻² h⁻¹ and an extremely low reverse salt flux (1.25 g m⁻² h⁻¹). Meanwhile, it achieves an excellent perm-selectivity with a ratio of water to salt permeability coefficient of 8.25 bar⁻¹. Moreover, it exhibits an outstanding antifouling capacity. The work sheds light on fabricating high perm-selective membranes for desalination.     

Cellulose triacetate/LUDOX-SiO2 nanocomposite for synthesis of pervaporation desalination membranes

A series of cellulose triacetate/Ludox-silica nancomposite pervaporation membranes was successfully prepared via solution casting, aiming to improve the performance of cellulose triacetate membranes for desalination. The fabricated nanocomposite membranes were characterized to study the membrane morphology, chemical composition, mechanical properties, and surface hydrophilicity. Furthermore, the desalination performance was investigated as a function of silica (SiO₂) loading (ranging from 1 to 4 wt%) and feed concentration at 30 and 60 g/L of sodium chloride (NaCl). Pervaporation experiments showed that incorporating 4 wt% SiO₂ into a cellulose triacetate (CTA) membrane increased the water flux by a factor 2.5 compared with pristine CTA (from 2.2 to 6.1 kg m⁻² h⁻¹) for a 30 g/L NaCl feed solution at 70°C, while the salt rejection remained above 99%. The CTA/4 wt% SiO₂ membrane was found to have only 21% flux reduction when tested with a 60 g/L NaCl feed solution, without changes in membrane selectivity. This suggests that the developed CTA/Ludox-SiO₂ nanocomposite pervaporation membrane is suitable for desalination.     

Poly(ethylene glycol) crosslinked sulfonated polysulfone composite membranes for forward osmosis

Forward osmosis (FO) membranes were prepared by a coating method with poly(ethylene glycol) crosslinked sulfonated polysulfone (SPSf) as a selective layer. The poly(ether sulfone)/SPSf substrate was prepared by phase inversion. The composite membranes were characterized with respect to membrane chemistry (by attenuated total reflectance/Fourier transform infrared spectroscopy and X‐ray photoelectron spectroscopy), hydrophilicity (by static contact angle measurement), and surface morphology (by scanning electron microscopy and atomic force microscopy). The FO performance was also characterized. The effects of the crosslinker concentration on the hydrophilicity and FO performance were investigated. The crosslinked membrane exhibited a high hydrophilicity with a lowest contact angle of 15.5°. Under FO tests, the membranes achieved a higher water flux of 15.2 L m^?2 h^?1 when used against deionized water as the feed solution and a 2 mol/L sodium chloride (NaCl) solution as the the draw solution. The membranes achieved a magnesium sulfate rejection of 96% and an NaCl rejection of 55% when used against a 1 g/L inorganic salt solution as the feed solution and a 2 mol/L glucose solution as the draw solution. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43941.     

Enhanced the antifouling and antibacterial performance of PVC/ZnO-CMC nanoparticles ultrafiltration membrane

Inorganic nanoparticles (NPs) have been employed in modification for polyvinyl chloride (PVC) membrane intrinsic hydrophobicity. Carboxymethyl chitosan (CMC), a natural organic matter, was used to relieve the agglomeration of zinc oxide (ZnO) NPs in the membrane matrix. In this paper, ZnO-CMC NPs were successfully prepared via co-precipitation approach, blended with PVC membranes, and the effect of ZnO-CMC NPs for the membrane properties was studied. The SEM and EDX confirmed excellent dispersion of ZnO-CMC NPs on the membrane surface. The enhanced hydrophilicity, porosity and inter-connected finger-like strcture of modified membranes confirmed by water contact angle and SEM. In addition, pure water flux of PVC/ZnO-CMC composite membrane was 107.36 L m⁻² h⁻¹ (PVC/ZnO-CMC (0.25 wt%)), which was higher than that of neat PVC membrane (83.11 L m⁻² h⁻¹). Importantly, the modified membranes exhibits lower static BSA adsorbtion because of the improved hydrophilicity, and a higher flux recovery rate (>90%) after three sequential filtration cycles. The antibacterial behavior of PVC/ZnO-CMC membrane was tested simply using Escherichia coli, and the results indicated that all composite membranes possess excellent antibacterial properties. Our work presents PVC/ZnO-CMC NPs composite membrane a promising future in wastewater treatment and antibacterial application.     

Fabrication of fullerenol-incorporated thin-film nanocomposite forward osmosis membranes for improved desalination performances

Development and use of novel membranes for forward osmosis (FO) applications have gained popularity throughout the world. To enhance FO membrane performance, a novel thin-film nanocomposite membrane was fabricated by interfacial polymerization incorporating Fullerenol (C₆₀(OH)_n) nanomaterial, having n in the range of 24–28 into the active layer. Different concentrations of fullerenol loading (100, 200, 400, and 800 ppm) were added to the top skin layer. The structural and surface properties of the pure thin-film composite membrane (TFC) and fullerenol-incorporated thin-film nanocomposite (FTFC) membranes, were characterized by ATR-FTIR, SEM, and AFM. FO performance and separation properties were evaluated in terms of water flux, reverse salt flux, antifouling propensity, water permeability and salt permeability for all TFC and FTFC membranes. Osmotic performance tests showed that FTFC membranes achieved higher water flux and reverse salt flux selectivity compared with those of TFC membranes. The FTFC membrane with a fullerenol loading of 400 ppm exhibited a water flux of 26.1 L m^?2 h^?1 (LMH), which is 83.03% higher than that of the TFC membrane with a specific reverse salt flux of 0.18 g/L using 1 M sodium chloride draw solution against deionized water in FO mode. The fullerenol incorporation in FTFC membranes also contributed to a decreased fouling propensity.     

Preparation and application of zinc oxide/poly(m-phenylene isophthalamide) hybrid ultrafiltration membranes

A small molecular-weight cut-off (MWCO) of 6000 Da poly(m-phenylene isophthalamide) (PMIA) embedded zinc oxide (ZnO) hybrid ultrafiltration (UF) membrane was synthesized via nonsolvent-induced phase separation (NIPS). Tests of field emission scanning electron microscope (FE-SEM), energy dispersive X-ray spectroscopy (EDX), atomic force microscopy (AFM), thermal gravimetric analyzer (TGA), Fourier transform infrared (FTIR), capillary flow porometer (CPF), mechanical test, and pure water flux (PWF) for characterization of membranes were carried out. The EDX, FTIR, and TGA indicated the presence of ZnO in the polymer matrix. The hybrid membranes showed enhanced pore density, PWF by the presence of the particles. The contact angle and water flux of modified membrane with 0.03 wt % of nano-ZnO were 47.7° and 52.58 L·m⁻²·h⁻¹ compared to 71.6° and 36.27 L·m⁻²·h⁻¹ respectively; Compared with the hydrophobic membrane, the PMIA membrane, with hydrophilicity, is supposed to exhibit good antifouling properties. Furthermore, the thermal stability and mechanical properties of the modified membranes were increased. Finally, the hybrid membrane was used in treating papermaking white wastewater and exhibited good separation and high water flux. The great properties of the ultrafiltration PMIA membranes indicate their potential for excellent performance in industrial applications. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47583.     

Effect of cellulose triacetate membrane thickness on forward‐osmosis performance and application for spent electroless nickel plating baths

Cellulose triacetate (CTA) forward‐osmosis (FO) membranes were prepared via the phase inversion method. The influence of thickness on the performance and morphology of CTA FO membranes was discussed in detail. When the thickness of the membrane was 50.0 ± 0.5 μm (CTA4), the prototype CTA membranes displayed a water flux of 20.2 L m^?2 h^?1 and a reverse salt transport of 14.6 g m^?2 h^?1 using 1 mol/L NaCl as the draw solution and deionized water as the feed solution during the FO process at 25 °C. In addition, the high‐performance CTA4 FO membranes have been used to process spent electroless nickel plating baths where the water flux could reach 13 L m^?2 h^?1 and NiSO₄·6H₂O crystals occurred in the feed solution of the spent electroless nickel plating baths. The recovery rates of NiSO₄·6H₂O and water from the spent electroless nickel plating baths were 44.54% and 53.53%, respectively. This study focused on improving membrane design for the FO process and finding a new method of waste liquor or wastewater treatment. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45049.     

Hydrophobic SiO2 nanoparticle-induced polyvinylidene fluoride crystal phase inversion to enhance permeability of thin film composite membrane

Thin film composite (TFC) membrane can get rid of small molecular contaminants and salts with a very high efficiency, thus exhibiting promising potential for addressing the emerging problem of a clean water shortage. In this work, a new type of TFC membrane was prepared by interfacial polymerization of two monomers (MPD and TMC) on surface of SiO₂/polyvinylidene fluoride (PVDF) substrate. The maximum flux of 3.16 L m⁻² h⁻¹ Bar⁻¹ was achieved for the optimized hydrophobic SiO₂ nanoparticles well dispersed in PVDF substrate, which is 2.6 times higher than that of 1.21 L m⁻² h⁻¹ Bar⁻¹ for the commercial cellulose triacetate reverse osmosis membrane. The improved performance of TFC membrane could be attributed to the higher compaction resistance of SiO₂/PVDF substrate. Further analysis revealed that PVDF crystal phase inversion induced by superhydrophobic SiO₂ nanoparticles obviously enhanced the intramolecular and intermolecular hydrogen bonds between PVDF polymer molecules. Additionally, the narrower finger-like pore size and thicker pore wall of SiO₂/PVDF substrate also played significant roles in enhancing the compaction resistance of PVDF membrane. This work also provides a proof-of-concept demonstration of high permeability substrates for effective flux enhancement of TFC membranes. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48204.     

Advanced FO membranes from newly synthesized CAP polymer for wastewater reclamation through an integrated FO‐MD hybrid system

A new cellulose acetate propionate (CAP) polymer has been synthesized and used to prepare high‐performance forward osmosis (FO) membranes. With an almost equal degree of substitution of acetyl and propionyl groups, the CAP‐based dense membranes show more balanced physicochemical properties than conventional cellulose acetate (CA)‐based membranes for FO applications. The former have a lower equilibrium water content (6.6 wt. %), a lower salt diffusivity (1.6×10¹⁴ m² s^?1) and a much lower salt partition coefficient (0.013) compared with the latter. The as‐prepared and annealed CAP‐based hollow fibers have a rough surface with an average pore radius of 0.31 nm and a molecular weight cut off of 226 Da. At a transmembrane pressure of 1 bar, the dual‐layer CAP‐CA hollow fibers show a pure water permeability of 0.80 L m^?2 h^?1 bar^?1 (LMH/bar) and a rejection of 75.5% to NaCl. The CAP‐CA hollow fibers were first tested for their FO performance using 2.0 M NaCl draw solution and deionized water feed. An impressive water flux of 17.5 L m^?2 h^?1 (LMH) and a reverse salt flux of 2.5 g m^?2 h^?1 (gMH) were achieved with the draw solution running against the active CAP layer in the FO tests. The very low reverse salt flux is mainly resulting from the low salt diffusivity and salt partition coefficient of the CAP material. In a hybrid system combining FO and membrane distillation for wastewater reclamation, the newly developed hollow fibers show very encouraging results, that is, water production rate being 13–13.7 LMH, with a MgCl₂ draw solution of only 0.5 M and an operating temperature of 343 K due to the incorporation of bulky propionyl groups with balanced physiochemical properties. © 2012 American Institute of Chemical Engineers AIChE J, 59: 1245–1254, 2013     

Fabrication and characterization of silane-functionalized Na-bentonite polysulfone/polyethylenimine nanocomposite membranes for dye removal

In this study, tetraethoxysilane (TEOS)-functionalized Na-bentonite incorporated into polysulfone/polyethylenimine (PSF/PEI) membranes were fabricated by phase inversion method for the efficient removal of methylene blue dye. For the preparation of PSF/PEI nanocomposite membranes, silane-functionalized Na-bentonite and pure Na-bentonite were used at three different concentrations (0.5, 1, and 2 wt%). The prepared membranes were characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, atomic force microscopy, porosity, hydrophilicity, and water permeability measurements. Antifouling behaviors and methylene blue dye rejections of the PSF/PEI nanocomposite membranes were also tested. The obtained results showed that the addition of pure Na-bentonite and silane-functionalized Na-bentonite both increased the water permeability of the membranes. The PSF/PEI membrane containing 2 wt% silane-functionalized Na-bentonite showed the highest water flux of 105 L m⁻² h⁻¹, while the lowest water flux of 1.2 L m⁻² h⁻¹ was recorded for pure PSF membrane. Filtration results demonstrated that the antifouling capacity was significantly increased due to the negatively charged surface of the newly generated silane-functionalized Na-bentonite PSF/PEI membranes. In summary, TEOS-functionalized Na-bentonite can be used to fabricate PSF/PEI nanocomposite membranes with effective filtration ability, antifouling capacity with lower decay ratio, higher flux recovery ratio, and 99% methylene blue dye removal performance.     

Characteristics and potential applications of a novel forward osmosis hollow fiber membrane

There has been a resurgence of interest in forward osmosis (FO) as a potential means of desalination, dewatering and in pressure retarded osmosis, which Sidney Loeb was advocating over 3 decades ago. This paper describes the characteristics and potential applications of a newly developed FO hollow fiber membrane, which was fabricated by interfacial polymerization on the inner surface of a polyethersulfone (PES) hollow fiber. This FO membrane presents excellent intrinsic separation properties, with a water flux of 42.6 L/m² h using 0.5 M NaCl as the draw solution and DI water as the feed with the active layer facing the draw solution orientation at 23 °C. The corresponding ratio of salt flux to water flux was only 0.094 g/L, which is superior to all other FO membranes reported in the open literature. To evaluate different application scenarios, various NaCl solutions (500 ppm (8.6 mM), 1 wt.% (0.17 M) and 3.5 wt.% (0.59 M)) were used as the feed water to test the performance of the FO membrane. The membrane can achieve a water flux of 12.4 L/m² h with 3.5 wt.% NaCl solution as the feed and 2 M NaCl as the draw solution, suggesting it has good potential for seawater desalination.     

Morphological controlling of CTA forward osmosis membrane using different solvent-nonsolvent compositions in first coagulation bath

Cellulose triacetate (CTA) membranes were fabricated via a modified nonsolvent induced phase separation (NIPS) method. Different solvent-nonsolvent compositions in first coagulation bath (FCB) were introduced to optimize CTA membrane structures. The effects of FCB compositions, immersion time and mass ratio of solvent (N-methyl-2-pyrrolidone, NMP) and nonsolvent (water, ethanol, ethylene glycol and glycerol) on membrane morphology and performance were systematically investigated. Prospective membranes with a dense bottom layer and a scaffold-like top layer were obtained under room temperature, owing to the low relative energy difference (RED) between nonsolvent and polymer as well as the high viscosity of FCBs. A high water flux J_v (12.6 L m^?2 h^?1) and a low reserve salt flux J_s (1.32 g m^?2 h^?1) were obtained in the optimized membrane, with a structural parameter S of 119 μm. Compared with membranes prepared via conventional NIPS method and commercial CTA forward osmosis (FO) membranes, a remarkable improvement of J_s/J_v value and S value was achieved, indicating membranes with single dense-layer structure might suffer less from internal concentration polymerization (ICP) which is the main obstacle for the development of FO process. This study might help us pave the way to design superior CTA membrane structures for forward osmosis application.     

Structural manipulation of PES constituents to prepare advanced alternative polymer for ultrafiltration membrane

Polyethersulfone (PES) is the most well-known polymer for the preparation of ultrafiltration (UF) membrane, but its membrane suffers from fouling. In this study, two engineered polymers were synthesized to provide optimal antifouling properties for UF membranes that simultaneously benefit from good properties of polyamide and PES. The choice of polyamide is due to its prominent characteristics and the convenience of its synthesis with various functional groups in a cost-effective way. Two hydroxyl containing polyamide bearing sulfone groups (PAS) and ether group (PAE) were synthesized by polycondensation method. The UF membranes were fabricated using the phase inversion method via immersion precipitation of PAS, PAE, and PES in dimethylacetamide, as a solvent and water, as a nonsolvent. The obtained membranes were compared and characterized by means of atomic force microscopy, scanning electron microscopy, contact angle, and Fourier transform infrared spectroscopy in the attenuated total reflection mode. The performance of membranes illustrated that the PAS and PAE membranes in comparison with the PES membrane had better porosity, water permeability, lesser protein fouling, more vertically finger-like pores, and more hydrophilic surface. The water permeability of PES, PAE, and PAS was 7.3, 64.0, and 78.0 L m⁻² h⁻¹ while their flux recovery ratio was 59.4, 83.3, and 86.7%, respectively. The promising permeability and antifouling properties of the PAS are potentially applicable in the efficient industrial separation and wastewater treatment. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 137, 48690.     

Enhancing the permeability of reverse osmosis membrane by embedding the star-like rigid supports in the substrate

Thin film composite (TFC) reverse osmosis (RO) membranes with high permeability have been prepared by interfacial polymerization based on tailoring the polysulfone (PSf) substrate structure by in situ embedded poly(p-phenylene terephthamide) (PPTA) star-like rigid supports. The star-like rigid supports were observed by the polarizing optical microscopy (POM) and transmission electron microscope (TEM). The surface properties of the substrates were investigated by FTIR, the water contact angle (WCA), FESEM and AFM. The WCA was decreased from 88.5° to 72.3° with the PPTA increasing from 0% to 8%, and the surface roughness increased from 24.2, 25.1, 33.5 and 58.6 nm, respectively. Furthermore, numerous interconnect micro-structures were constructed in the substrate when the PPTA content was up to 8%. The pure water flux of 8% PPTA/92%PSf substrate was up to 377.0 L m⁻² h⁻¹ and the flux decline rate was lowest (64%) after compacted at 5.5 MPa for 30 min. Otherwise, increasing the PPTA contents in the substrate enhanced the roughness, encouraged nanosheet formation and improved the permeability of TFC RO membranes. The pure water flux of the TFC RO membranes increased from 36.32 to 58.42 L m⁻² h⁻¹, where the NaCl rejection was about 99.5% at 5.5 MPa.     

Evaluation of the possibility of utilization of poly(amidesulfonamide)s (PASAs) in ultrafiltration technology

Ultrafiltration (UF) membranes of six selected poly(amidesulfonamide)s (PASAs) were prepared and studied. The pure water flux and the retention of albumin (bovine serum) were used to evaluate the quality of the UF performance of the fabricated membrane. Membranes with good mechanical strength were obtained by using the phase inversion method. A comparison of the UF performance of the PASA membranes fabricated from a casting solution containing 12% w/w PASAs and 4% w/w lithium bromide in dimethylacetamide was made. The best retention of albumin (bovine serum) by membranes prepared under the conditions studied from the selected homopolymers of PASAs, and their corresponding pure water flux at 0.207 MPa, ranged from 84.6 to 100% and 120 to 396 L m⁻² h⁻¹, respectively. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 68: 2087–2093, 1998     

Improved separation performance of polyamide based reverse osmosis membrane incorporated with poly(dopamine) coated carbon nanotubes

A series of polyamide thin-film nanocomposite (PA TFN) membranes have been fabricated by incorporating hydrophilic poly(dopamine) (PDA) coated carbon nanotubes (CNTs@PDA) into the PA selective layer via interfacial polymerization. The effects of PDA coating thickness on surface characteristics and separation performances of membranes are studied in detail. The PDA coating makes the surface of PA TFN membrane more hydrophilic, smoother and less electronegative. The desalination performance is obviously influenced by the coating thickness of PDA and the loading concentration of PDA@CNTs. The water fluxes of PDA@CNTs incorporated PA TFN membranes have been improved without sacrificing NaCl rejections. When the loading concentration is 0.0010%, the maximum water flux is 48.1 L m⁻² h increasing by 45% compared with that of pristine PA membrane. Meanwhile, the NaCl rejection is up to 99.8%. The CNTs@PDA incorporated PA TFN membranes exhibit better anti-fouling property and separation performance durability. This work proves that CNTs@PDA has great potential application in PA TFN membranes.     

Fabrication of low thermal conductivity yttrium silicate ceramic flat membrane for membrane distillation

This paper reports on the successful fabrication of γ-Y₂Si₂O₇ membranes with low thermal conductivity, which is an important membrane property for achieving high performance in membrane distillation process. Single-phase γ-Y₂Si₂O₇ powder was first synthesized by calcination of SiO₂ and Y₂O₃ powders, with 3 wt% LiYO₂ as a sintering aid. The membrane was produced by tape-casting of a suspension of this powder. After sintering at 1300 °C for 4 h, a flat membrane was obtained, which had a thickness of 0.5 mm, 49% porosity, 0.9 μm pore diameter, and low thermal conductivity of 0.497 W/m⋅K at 32 °C, and 0.528 W/m⋅K at 100 °C. The obtained membrane presented hydrophobic features (water contact angle was 132°) after surface modification, which resulted in formation of a strongly adhered robust hydrophobic SiNCO nanoparticle layer on its surface. The resultant hydrophobic membrane was tested in water desalination experiments using a sweeping gas membrane distillation (SGMD) device. High water flux of 10.07 L⋅ m⁻²⋅ h⁻¹ was achieved for a 20 wt% NaCl feeding solution and a temperature at the feed of 90 °C. Stable water flux and rejection rates were recorded in long-term experiments (>400 h).     

Preparation and characterization of nanoparticle-filled,mixed-matrix membranes for the pervaporation dehydration of isopropyl alcohol

Novel polymeric mixed-matrix membranes (MMMs) were prepared by the incorporation of different amounts of 13X zeolite into a sodium carboxymethylcellulose (NaCMC)/poly(vinyl alcohol) (PVA) blend matrix. The resulting MMMs were characterized by attenuated total reflectance–Fourier transform infrared spectroscopy to analyze the possible chemical reactions between NaCMC, PVA, zeolites, and glutaraldehyde. Scanning electron microscopy, differential scanning calorimetry, thermogravimetric analysis, and X-ray diffraction were used to analyze the surface morphology, thermal stability, and crystallinity, respectively, of the membranes. Swellings studies were performed at 35°C, and we found that membranes containing 20 wt % zeolite showed higher values (960 kg m⁻² h⁻¹) at 17.5 wt % water in an isopropyl alcohol (IPA)/water mixture. Pervaporation (PV) experiments were also performed to evaluate the membrane performance in different compositions of the IPA/water mixture at 35°C. The mechanical properties were also tested, and we found that the optimum mechanical strength and percentage elongation at break were 42.24 N/mm² and 3.38, respectively, for the membrane containing 15 wt % zeolite. The experimental results show that both the flux and selectivity increased with increasing zeolite content. The membrane containing 20 wt % zeolite showed the highest separation selectivity (5118) with a substantial flux of 0.121 kg m⁻² h⁻¹ at 35°C and with 10 wt % water in the feed; this suggested that the membranes could be used effectively to break the azeotropic point of the water–IPA mixture, so as to remove a small amount of water from IPA. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012