Top illuminated organic photodetectors with dielectric/metal/dielectric transparent anode

The top illuminated organic photodetectors (OPDs) with a Dielectric/Metal/Dielectric (DMD) transparent anode are fabricated. The transparent electrode is composed of molybdenum trioxide (MoO₃)/silver (Ag)/MoO₃ layers and zinc oxide (ZnO)/aluminum (Al) is used for bottom cathode. The optimized DMD electrode has an optical transmittance of 85.7% at the wavelength of 546 nm and sheet resistance of ∼6 Ω/sq. The fabricated OPDs exhibit a high detectivity and wide range linearity.     

Flexible organic light-emitting diodes with ZnS/Ag/ZnO/Ag/WO3 multilayer electrode as a transparent anode

We investigated the highly flexible, transparent and very low resistance ZnS/1st Ag/ZnO/2nd Ag/WO₃ (ZAZAW) multilayer electrodes on PET substrate as an anode in flexible organic light-emitting diodes (OLEDs). A theoretical calculation was first conducted to obtain the optimal thickness of the ZAZAW multilayer for high transparency. Its measured luminous transmittance was over 80% in the visible range with a very low sheet resistance of 2.17 Ω/sq., and it had good mechanical flexibility due to the ductility of Ag. Ag’s effect on optical and electrical properties was also studied. Flexible OLEDs devices that were fabricated on ZAZAW multilayer anode showed good hole injection properties comparable to those of ITO-based OLEDs due to the use of WO₃ as a hole injection layer. However, the electroluminescent properties of the ZAZAW-based OLEDs varied depending on WO₃ thickness. Although the transmittance of the ZAZAW electrode was reduced by tuning the WO₃ thickness to adjust the microcavity effect, the device efficiency could be enhanced above that of ITO-based OLEDs.     

Organic/metal hybrid cathode for transparent organic light-emitting diodes

We report a highly transparent organic/metal hybrid cathode of a Cs-doped electron transport layer (Cs-ETL)/Ag for transparent organic light-emitting diode (TOLED) applications. Particular attention is paid to the surface morphology on the Ag film and its influence on the optical transparency and electrical conductivity. With the use of Cs-ETL, a smooth and continuous surface morphology of Ag film was achieved, leading to a high transmittance of ～75% in TOLED with a low sheet resistance of 4.5 Ω/Sq in cathode film. We successfully applied our Cs-ETL/Ag transparent cathode to fabricate highly transparent OLEDs. Our approach suggests a new electrode structure for transparent OLED applications.     

ZnO/Ag/ZnO多层膜的制备和性质研究

采用射频磁控溅射ZnO陶瓷靶和直流磁控溅射Ag靶的方法制备了ZnO/Ag/ZnO多层膜。用X射线衍射仪、紫外–可见分光光度计、四探针测试仪和金相显微镜对ZnO/Ag/ZnO薄膜的结构、光学透过率、方阻和稳定性进行了研究。结果表明,ZnO(60nm)/Ag/(10nm)/ZnO(60nm)薄膜呈现多晶结构,薄膜在520nm处的光学透过率高达87.5%,方阻Rs为6.2Ω/□。随着顶层ZnO薄膜厚度的增加,ZnO/Ag/ZnO薄膜的稳定性提高。     

Fabrication of Ag nanoparticle/ZnO thin films using dual-plasma-enhanced metal-organic chemical vapor deposition (DPEMOCVD) system incorporated with photoreduction method and its application

We report a novel method to grow silver nanoparticle/zinc oxide (Ag NP/ZnO) thin films using a dual-plasma-enhanced metal-organic chemical vapor deposition (DPEMOCVD) system incorporated with a photoreduction method. The crystalline quality, optical properties, and electrical characteristics of Ag NP/ZnO thin films depend on the AgNO₃ concentration or Ag content and annealing temperature. Optimal Ag NP/ZnO thin films have been grown with a AgNO₃ concentration of 0.12 M or 2.54 at%- Ag content and 500 °C- rapid thermal annealing (RTA); these films show orientation peaks of hexagonal-wurtzite-structured ZnO (002) and face-center-cubic-crystalline Ag (111), respectively. The transmittance and resistivity for optimal Ag NP/ZnO thin films are 85% and 6.9×10⁻⁴ Ω cm. Some Ag NP/ZnO transparent conducting oxide (TCO) films were applied to InGaN/GaN LEDs as transparent conductive layers. The InGaN/GaN LEDs with optimal Ag NP/ZnO TCO films showed electric and optical performance levels similar to those of devices fabricated with indium tin oxide.     

室温下制备的ZnO/Ag/ZnO多层膜的性能

采用射频磁控溅射ZnO陶瓷靶、直流磁控溅射Ag靶的方法在室温下制备了不同厚度的ZnO/Ag/ZnO多层膜。对样品进行了研究。结果表明:随着Ag层厚度的增加,ZnO(002)衍射峰的强度先增加后减小,Ag(111)衍射峰的强度增强,ZnO/Ag/ZnO多层膜的面电阻先减小后趋于稳定。ZnO膜厚度增加,Ag膜易形成晶状结构,ZnO/Ag/ZnO多层膜的透射峰向长波方向移动。ZnO(60nm)/Ag(11nm)/ZnO(60nm)膜在554nm处的透过率高达92.3%,面电阻为4.2?/□,品质常数?TC最佳,约40×10–3/?。     

Transparent Al/WO3/Au film as anode for high efficiency organic light-emitting diodes

A transparent Al/WO₃/Au anode is introduced to fabricate high efficiency organic light-emitting devices (OLEDs). By optimizing the thicknesses of each layers of the Al/WO₃/Au structure, the transmittance of Al(7 nm)/WO₃(3 nm)/Au(13 nm) has reached over 55%. Concerning the performance of OLEDs using the optimized anode, the electroluminescence (EL) current efficiency and brightness are enhanced and the EL spectrum is greatly narrowed as compared to the OLEDs using indium-tin-oxide (ITO) as the anode. The results indicate that the metal/metal oxide/metal transparent electrode is a good structure for the anode of high performance OLEDs. In addition, Al/WO₃/Au can function as a composite transparent electrode for top-emitting OLEDs.     

Optimized ITO-free tri-layer electrode for organic solar cells

The optical properties of ZnO/Ag/ZnO (ZAZ) multilayer structures were numerically modeled and calculated by a FDTD method. Such tri-layers were also manufactured using an ion beam sputtering plant. A good agreement is obtained between modelizations and realizations. The impact of the oxide thicknesses on the optical properties of the ZAZ structures were experimentally and numerically investigated, and allow us to adjust the spectral position of the transmission maximum. The transmission of these structures is optimized up to around 74%, on the whole absorption spectral range of the photoactive P3HT:PCBM bulk heterojunction. The best electrode design is glass/ZnO (30 nm)/Ag (14 nm)/ZnO (30 nm), which presents a sheet resistance of 7 Ω/□. The optimized ZAZ structure was successfully integrated in an organic solar cell as anode. A photovoltaic efficiency of 2.58% is obtained and is compared to an organic solar cell integrating a traditional ITO anode with an efficiency of 2.99%. Numerical calculations of the intrinsic absorption inside each layer of the organic solar cells are performed. Alternative ITO-free electrodes for organic solar cells are demonstrated.     

Ag层的厚度对ZnO/Ag/ZnO多层膜性能的影响

采用射频磁控溅射ZnO陶瓷靶、直流磁控溅射Ag靶的方法制备了不同厚度Ag夹层的ZnO(60nm)/Ag/ZnO(60nm)多层膜.分别用X射线衍射仪、紫外可见分光光度计、四探针测试仪对样品的结构、光学性质、电学性质进行了研究.结果表明:随着Ag层厚度的增加,ZnO/Ag/ZnO多层膜呈现多晶结构,Ag(111)衍射峰的强度增强.Ag夹层厚度为11nm时,ZnO(60nm)/Ag/ZnO(60nm)膜在554nm处的透过率高达92.3%.随着Ag层厚度的增加,Ag膜的特征吸收峰呈现红移和宽化,ZnO/Ag/ZnO多层膜的面电阻先减小后趋于稳定.     

All‐Solution‐Processed Indium‐Free Transparent Composite Electrodes based on Ag Nanowire and Metal Oxide for Thin‐Film Solar Cells

Fully solution‐processed Al‐doped ZnO/silver nanowire (AgNW)/Al‐doped ZnO/ZnO multi‐stacked composite electrodes are introduced as a transparent, conductive window layer for thin‐film solar cells. Unlike conventional sol–gel synthetic pathways, a newly developed combustion reaction‐based sol–gel chemical approach allows dense and uniform composite electrodes at temperatures as low as 200 °C. The resulting composite layer exhibits high transmittance (93.4% at 550 nm) and low sheet resistance (11.3 Ω sq^‐1), which are far superior to those of other solution‐processed transparent electrodes and are comparable to their sputtered counterparts. Conductive atomic force microscopy reveals that the multi‐stacked metal‐oxide layers embedded with the AgNWs enhance the photocarrier collection efficiency by broadening the lateral conduction range. This as‐developed composite electrode is successfully applied in Cu(In_1‐x,Ga_x)S₂ (CIGS) thin‐film solar cells and exhibits a power conversion efficiency of 11.03%. The fully solution‐processed indium‐free composite films demonstrate not only good performance as transparent electrodes but also the potential for applications in various optoelectronic and photovoltaic devices as a cost‐effective and sustainable alternative electrode.     

Ultra-thin and graded sliver electrodes for use in transparent pentacene field-effect transistors

The authors report the fabrication of efficient and transparent pentacene field-effect transistors (FETs) using a graded structure of ultra-thin silver (Ag) source and drain (S–D) electrodes. The S–D electrodes were prepared by thermal evaporation with a controlled deposition rate to form Ag layer with a graded structure, leading to a reduced injection barrier and smoothing the contact surface between the electrode and the pentacene channel. The sheet resistance of such Ag electrode was found to be as low as 9 Ω/sq. In addition, a hole-only behavior of device with Ag electrode characterized by current–voltage measurement and conductive atomic-force microscopy shows the injection property of high current flowing as compared with device using Au electrode, resulting in an efficient injection condition existing at the interface of the graded Ag/pentacene. Device characterization indicates the transparent pentacene FET with a graded ultra-thin Ag electrode and organic capping layer of N,N′-di(1-naphthyl)-N,N′-diphenylbenzidine exhibits a high transmission rate of ∼75% in the range of visible light from 400 to 550 nm, a threshold voltage of −6.0 V, an on–off drain current ratio of 8.4 × 10⁵, and a field-effect mobility of 1.71 cm²/V s, thus significantly outperforming pentacene FETs with multilayer oxide electrodes or other transparent thin metal layers.     

Sol-gel-derived ZnO/Cu/ZnO multilayer thin films and their optical and electrical properties

Sol-gel preparation of transparent conducting ZnO/Cu/ZnO multilayer thin films has been investigated. CuO thin films were deposited on glass substrates via a dip-coating method. The CuO thin films were further subjected to reductive annealing in hydrogen to form highly conductive Cu thin films with sheet resistances as low as 10 Ω/□. ZnO/Cu/ZnO multilayers were successfully prepared in a similar way by reducing ZnO/CuO/ZnO. The sheet resistance of the ZnO/Cu/ZnO multilayer thin films is about 10 kΩ/□, which is much higher than that of the pure Cu thin films. The formation of large discrete Cu crystallites in the multilayers explains the poor electrical conductivity of the sol-gel-derived ZnO/Cu/ZnO multilayers.     

透明叠层结构Ag/MoO_3/Ag阳极对绿光OLED器件性能的影响

本文采用一种结构为Ag/MoO_3/Ag的金属/氧化物/金属(M_1/O/M_2)叠层替代ITO作为OLED器件的阳极,研究Ag/MoO_3/Ag叠层结构变化对于OLED器件电极透过率、亮度、光谱等性能的影响。实验采用真空蒸镀方法制备了一系列器件,器件结构为Ag/MoO_3/Ag/MoO_3(10nm)/NPB(40nm)/Alq_3(60nm)/LiF(1nm)/Al(150nm)。对比器件的电压-电流密度、电压-亮度、光谱特性等数据,表明Ag/MoO_3/Ag的结构为20/20/10(nm)时,器件性能较好。在驱动电压为11V时,其亮度达到18 421cd/m~2,电流效率为2.45cd/A;且因器件中存在微腔效应,其EL光谱蓝移,半高宽变窄。但考虑到530nm处其电极透过率仅为17%,所以经换算该器件实际发光亮度比ITO电极器件更高。该Ag/MoO_3/Ag叠层阳极制作相对简单,经优化后在顶发射和柔性OLED器件方面将具有一定的应用前景。     

A highly conductive PEDOT:PSS film with the dipping treatment by hydroiodic acid as anode for organic light emitting diode

A highly conductive, transparent and uniform poly (3,4-ethylenedioxythiophene):poly (styrenesulfonate) (PEDOT:PSS) film has been developed by dipping treatment with hydriodic acid (HI) solution. The HI-treated PEDOT:PSS film can reach a sheet resistance of 68 Ω per square and a transmittance of 87% at 550 nm. The conductivity enhancement for the HI-treated film is ascribed to the permeation of proton and iodine anion of HI into PEDOT:PSS film, resulting in the separation of PSS and PEDOT chains. The phase separation of PSS and PEDOT can provide more conductive pathways for carriers to improve conductivity of the film. Using the optimized HI-treated PEDOT:PSS film as anode, we have fabricated indium tin oxide (ITO)-free organic light emitting diode (OLED), which shows better performance than the device with ITO as anode. This proves that such PEDOT:PSS film with the dipping treatment by HI solution is a promising alternative to ITO for low cost, transparent and flexible OLED application.     

An efficient inverted organic solar cell with improved ZnO and gold contact layers

This paper presents a high efficiency (～3.8%) inverted organic photovoltaic devices based on a P3HT:PCBM bulk heterojunction (BHJ) blend with improved electron- and hole-selective contact layers. Zinc oxide (ZnO) nanoparticle films with different thicknesses are deposited on the transparent electrodes as a nano-porous electron-selective contact layer. A thin gold film is used between the BHJ photoactive layer and the poly(3,4-ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT:PSS), which improves the wettability and significantly enhances the stability of the device (>50 days of air exposure). Photovoltaic device parameters such as power conversion efficiency (PCE) and external quantum efficiency (EQE) are systematically examined for inverted devices with different thicknesses of ZnO and gold layers in comparison to the non-inverted and reference inverted devices with no contact layers. The optimized organic devices with ZnO and Au contact layers show exceptional short circuit currents (in excess of 13 mA/cm²), in comparison to the reference devices, which is related to increased quantum efficiency of the device observed in measured EQE experiments. These results are important for development of high efficiency and stable all-printed organic solar cells and point out the role of contact layers, in particular, ZnO conductivity and morphology in the device performance.     

Properties of ZnO/Cu/ZnO multilayer films deposited by simultaneous RF and DC magnetron sputtering at different substrate temperatures

ZnO/Cu/ZnO transparent conductive multilayer films are prepared by simultaneous RF sputtering of ZnO and DC sputtering of Cu. The properties of the multilayer films are studied at different substrate temperatures. Sheet resistance of the multilayer film decreased initially with increase of substrate temperature and increased further with increase of substrate temperature beyond 100 °C. However, transmittance of the multilayer film increased with increase of substrate temperature. Good transparent conductive film of sheet resistance 9.3 Ω/sq and transmittance of 85% was found at a substrate temperature of 100 °C. The performance of the multilayer film was evaluated using a figure of merit. The observed property of the multilayer film is suitable for the application of transparent conductive electrodes.     

Study on the thermal stability of Ga-doped ZnO thin film: A transparent conductive layer for dye-sensitized TiO2 nanoparticles based solar cells

Generally, optoelectronic devices are fabricated at a high temperature. So the stability of properties for transparent conductive oxide (TCO) films at such a high temperature must be excellent. In the paper, we investigated the thermal stability of Ga-doped ZnO (GZO) transparent conductive films which were heated in air at a high temperature up to 500 °C for 30 min. After heating in air at 500 °C for 30 min, the lowest sheet resistance value for the GZO film grown at 300 °C increased from 5.5 Ω/sq to 8.3 Ω/sq, which is lower than 10 Ω/sq. The average transmittance in the visible light of all the GZO films is over 90%, and the highest transmittance is as high as 96%, which is not influenced by heating. However, the transmittance in the near-infrared (NIR) region for the GZO film grown at 350 °C increases significantly after heating. And the grain size of the GZO film grown at 350 °C after annealing at 500 °C for 30 min is the biggest. Then dye-sensitized TiO2 NPs based solar cells were fabricated on the GZO film grown at 350 °C (which exhibits the highest transmittance in NIR region after heating at 500 °C for 30 min) and 300 °C (which exhibits the lowest sheet resistance after heating at 500 °C for 30 min). The dye-sensitized solar cell (DSSC) fabricated on the GZO film grown at 350 °C exhibits superior conversion efficiency. Therefore, transparent conductive glass applying in DSSCs must have a low sheet resistance, a high transmittance in the ultraviolet–visible–infrared region and an excellent surface microstructure.     

Transparent Ultrathin Oxygen‐Doped Silver Electrodes for Flexible Organic Solar Cells

An effective method for depositing highly transparent and conductive ultrathin silver (Ag) electrodes using minimal oxidation is reported. The minimal oxidation of Ag layers significantly improves the intrinsic optical and structural properties of Ag without any degradation of its electrical conductivity. Oxygen‐doped Ag (AgO_x) layers of thicknesses as low as 6 nm exhibit completely 2D and continuous morphologies on ZnO films, smaller optical reflections and absorbances, and smaller sheet resistances compared with those of discontinuous and granular‐type Ag layers of the same thickness. A ZnO/AgO_x/ZnO (ZAOZ) electrode using an AgO_x (O/Ag = 3.4 at%) layer deposited on polyethylene terephthalate substrates at room temperature shows an average transmittance of 91%, with a maximum transmittance of 95%, over spectral range 400?1000 nm and a sheet resistance of 20 Ω sq^?1. The average transmittance value is increased by about 18% on replacing a conventional ZnO/Ag/ZnO (ZAZ) electrode with the ZAOZ electrode. The ZAOZ electrode is a promising bottom transparent conducting electrode for highly flexible inverted organic solar cells (IOSCs), and it achieves a power conversion efficiency (PCE) of 6.34%, whereas an IOSC using the ZAZ electrode exhibits a much lower PCE of 5.65%.     

Regulating Ag Wettability via Modulating Surface Stoichiometry of ZnO Substrates for Flexible Electronics

A novel and highly efficient methodology to regulate (enhance or suppress) the Volmer–Weber 3D growth mode of ultra-thin (<10 nm) Ag layers by modulating the surface stoichiometry of ZnO substrates prior to Ag deposition is presented. Relative to pristine ZnO layers, oxygen-deficient surface states formed by preferential removal of surface oxygen atoms remarkably improve Ag layer wettability, whereas oxygen-excessive surface states formed by oxygen atom incorporation strongly facilitate Ag agglomeration. The dissimilar nucleation and coalescence dynamics are elucidated via combined molecular dynamics and force-bias Monte Carlo simulations. The improved wettability results in significantly lower sheet resistance in the ultra-thin (6–10 nm) Ag layers, for example, 6.03 Ωsq⁻¹ at 8 nm, than the previously reported values from numerous other approaches in the equal thickness range. When this unique methodology is applied to ZnO/Ag/ZnO transparent electrodes, simultaneous improvement in electrical conductivity and visible transparency is realized, with a resultant Haacke figure of merit value of 0.139 Ω⁻¹ that is >50% higher than the best reported value for an identically structured electrode. We select transparent heating devices as a model system to confirm that the superior optoelectronic properties are highly sustainable under simultaneous and severe electrical, mechanical, and thermal stresses.     

Near infra-red transparent Mo-doped In2O3 by hetero targets sputtering for phosphorescent organic light emitting diodes

We report a highly near infrared (NIR) transparent MoO₃-doped In₂O₃ (IMO) film prepared by hetero target sputtering for use as a transparent anode in phosphorescent organic light emitting diodes (OLEDs). Effective activation of Mo dopant in the In₂O₃ matrix and good crystallinity with the (2 2 2) preferred orientation from by rapid thermal annealing (RTA) led to the lowest resistivity of 4.25 × 10^?4 Ohm cm and sheet resistance of 16.9 Ohm/square, comparable to a conventional ITO anode without lose of transparency in the NIR region. Due to high carrier mobility in the IMO matrix, IMO film exhibited higher transmittance in the visible and NIR regions compared to ITO film even though it has a similar resistivity. Both synchrotron X-ray scattering and high resolution transmission electron microscope examinations showed that the optimized IMO film annealed at 600 °C had a rectangular shaped columnar structure with a strongly preferred (2 2 2) orientation. Identical current density–voltage–luminance and quantum efficiency of the phosphorescent OLED fabricated on an IMO anode were comparable to those of the OLED on a reference ITO anode due to the high transparency and low resistivity of the IMO anode.