Effect of branched alkyl groups on physical properties in poly(ethylene-co-branched alkyl methacrylate)s

Summary Poly(ethylene-co-5.4 mol% n-alkyl/branched alkyl methacrylate)s (PEM) were prepared by a dehydrogenchloride reaction of poly(ethylene-co-5.4 mol% alkyl methacrylic chloride) with the corresponding alkyl alcohol to investigate effect of branching structure and length of alkyl ester on a few physical properties of PEM [glass transition temperature (T_g), degree of crystallinity in polyethylene region (X_c) and dielectric molecular motion], where the alkyl groups used here are n-propyl, n-butyl, n-hexyl, n-decyl, 2-ethylhexyl, 3,5,5-trimethylhexyl and 2-(1,3,3-trimethylbutyl)-5,7,7-trimethyloctyl. In the n-alkyl methacrylate copolymers, T_g and X_c were almost unchanged with the presence of alkyl ester, but T_g increased and X_c decreased in the highly branched alkyl methacrylate copolymers even at the low methacrylate content of 5.4 mol%.     

Synthesis and micellization behavior of amphiphilic graft copolymer with 1‐octene as hydrophobic moiety

Two new kinds of amphiphilic copolymers were synthesized in this work. Poly(1‐octene‐co‐acrylic acid) copolymers were prepared through the copolymerization of 1‐octene and tert‐butyl acrylate, and the hydrolysis of tert‐butyl acrylate units. Poly(1‐octene‐co‐acrylic acid)‐g‐poly (ethylene glycol) copolymers were obtained from the esterification reaction between poly(1‐octene‐co‐acrylic acid) and poly(ethylene glycol) monomethyl ether. They were characterized by means of ¹H‐NMR, ¹³C‐NMR, GPC, and FTIR. These amphiphilic copolymers can form stable micelles in aqueous solutions. The critical micelle concentration was determined by fluorescence spectroscopy. The micellar morphology and size distribution were investigated by transmission electron microscopy and dynamic light scattering. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effect of ethylene ionomers on the properties of crosslinked polyethylene

Most premature failure of underground crosslinked polyethylene (XLPE) cables in service, a matter of great concern, is due to aging induced by water treeing. To improve the water‐tree resistance, sodium‐neutralized poly (ethylene‐co‐acrylic acid) (EAA–Na) ionomers were blended with XLPE; the EAA–Na ionomers were prepared through the neutralization of sodium hydroxide and poly(ethylene‐co‐acrylic acid). A series of XLPE/EAA–Na ionomer blends were investigated through the measurement of the water absorption ratio, water treeing, and mechanical and dielectric testing; the results strongly suggested that EAA–Na ionomers could improve the water‐tree resistance of XLPE, and the XLPE/EAA–Na blends retained excellent mechanical properties and dielectric properties. Moreover, through the characterization of XLPE/EAA–Na blends with Fourier transform infrared spectrometry, dynamic mechanical analysis, and scanning electron microscopy, it was found that the neutralization reaction could be achieved completely; the XLPE and EAA–Na ionomers were partially compatible, so the EAA–Na ionomers could be dispersed well in the matrix with the process examined in this study. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3483–3490, 2007     

Synthesis and evaluation of biodegradable segmented multiblock poly(ether ester) copolymers for biomaterial applications

Based on 1,4‐succinic acid, 1,4‐butanediol, poly(ethylene glycol)s and dimethyl terephthalate, biodegradable segmented multiblock copolymers of poly[(butylene terephthalate)‐co‐poly(butylene succinate)‐block‐poly(ethylene glycol)] (PTSG) were synthesized with different poly(butylene succinate) (PBS) molar fractions and varying the poly(ethylene glycol) (PEG) segment length, and were evaluated as biomedical materials. The copolymer extracts showed no in vitro cytotoxicity. However, sterilization of the copolymers by gamma irradiation had some limited effect on the cytotoxicity and mechanical properties. A copolymer consisting of PEG‐1000 and 20 mol% PBS, assigned as 1000PBS20 after SO₂ gas plasma treatment, sustained the adhesion and growth of dog vascular smooth muscle cells. The in vivo biocompatibility of this sample was also measured subcutaneously in rats for 4 weeks. The assessments indicated that these poly(ether ester) copolymers are good candidates for anti‐adhesion barrier and drug controlled‐release applications. Copyright © 2004 Society of Chemical Industry     

Effects of experimental variables on the synthesis of porous matrices

Macroporous beads, poly(ethylene glycol dimethacrylate‐co‐acrylic acid) [poly(EGDMA‐co‐AAc)], and poly(ethylene glycol dimethacrylate‐co‐hydroxyethyl methacrylate) [poly(EGDMA‐co‐HEMA)] were prepared by the suspension polymerization technique in the presence of a porogen agent. Different experimental conditions such as amount of initiator, porogen type, and temperature were studied to optimize the polymerization systems. These hydrophilic copolymers were characterized by IR spectroscopy, scanning electron microscopy, specific surface area, and swelling in water. A new parameter, H, defined as the ratio between the equilibrium weight swelling ratio (q_w) and equilibrium volume swelling ratio (q_v), allowed to select the reaction conditions from which matrices with high capacity of water sorption and low stretching degree were reached. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 920–927, 2001     

Double stimuli responsive mixed aggregates from poly(acrylic acid)-block-poly(ε-caprolactone)-block-poly(acrylic acid) and poly(ethylene oxide)-block-poly(propylene oxide)-block-poly(ethylene oxide) triblock copolymers

Well defined ABA triblock copolymer comprising a biodegradable poly(ε-caprolactone) (PCL) middle block and two pH responsive poly(acrylic acid) (PAA) outer blocks was synthesized by atom transfer radical polymerization of tert-butyl acrylate, initiated by PCL-based macroinitiator, followed by selective hydrolysis of the poly(tert-butyl acrylate) blocks. The cooperative self-assembly of the synthesized poly(acrylic acid)-block-poly(ε-caprolactone)-block-poly(acrylic acid) (PAA₂₂PCL₂₆PAA₂₂) copolymer with a temperature-responsive poly(ethylene oxide)-block-poly(propylene oxide)-block-poly(ethylene oxide) (PEO₂₆PPO₄₀PEO₂₆, Pluronic P85) triblock copolymer at different compositions in aqueous media was investigated. Based on experimental data, copolymer properties and composition, formation of nano-sized aggregates comprising a mixed PCL/PPO core and a mixed PEO/PAA corona is suggested. The binary mixture of PAA₂₂PCL₂₆PAA₂₂:PEO₂₆PPO₄₀PEO₂₆ copolymers at molar ratio 3:1 favors the formation of mixed aggregates only, while at higher PEO₂₆PPO₄₀PEO₂₆ content the aggregates coexist with pure PEO₂₆PPO₄₀PEO₂₆ micelles.     

Effect of acrylic acid neutralization on ‘livingness’ of poly[styrene‐ran‐(acrylic acid)] macro‐initiators for nitroxide‐mediated polymerization of styrene

BACKGROUND: The effect of acrylic acid neutralization on the degradation of alkoxyamine initiators for nitroxide‐mediated polymerization (NMP) was studied using styrene/acrylic acid and styrene/sodium acrylate random copolymers (20 mol% initial acrylate feed concentration) as macro‐initiators. The random copolymers were re‐initiated with fresh styrene in 1,4‐dioxane at 110 °C at SG1 mediator/BlocBuilder^® unimolecular initiator ratios of 5 and 10 mol%. RESULTS: The value of k_pK (k_p = propagation rate constant, K = equilibrium constant) was not significantly different for styrene/acrylic acid and styrene/sodium acrylate compositions at 110 °C (k_pK = 2.4 × 10^?6–4.6 × 10^?6 s^?1) and agreed closely with that for styrene homopolymerization at the same conditions (k_pK = 2.7 × 10^?6–3.0 × 10^?6 s^?1). All random copolymers had monomodal, narrow molecular weight distributions (polydispersity index M?_w/M?_n = 1.10–1.22) with similar number‐average molecular weights M?_n = 19.3–22.1 kg mol^?1. Re‐initiation of styrene/acrylic acid random copolymers with styrene resulted in block copolymers with broader molecular weight distributions (M?_w/M?_n = 1.37–2.04) compared to chains re‐initiated by styrene/sodium acrylate random copolymers (M?_w/M?_n = 1.33). CONCLUSIONS: Acrylic acid degradation of the alkoxyamines was prevented by neutralization of acrylic acid and allowed more SG1‐terminated chains to re‐initiate the polymerization of a second styrenic block by NMP. Copyright © 2008 Society of Chemical Industry     

Oxygen and carbon dioxide permeability of EAA/PEO blends and microlayers

The goal of this study was to broaden the spectrum of gas permeability and selectivity characteristics of poly(ethylene‐co‐acrylic acid) (EAA) by combining it with poly(ethylene oxide) (PEO), which has a high selectivity for CO₂. To obtain films that differed substantially in their solid state morphologies, EAA was combined with PEO as melt blends and as coextruded films with many alternating, continuous microlayers of EAA and PEO. The solid state structure and thermal behavior were characterized and the permeability to O₂ and CO₂ was measured at 23°C. When the PEO was dispersed as small domains, the particles were too numerous for most of them to contain a heterogeneity that was sufficiently active to nucleate crystallization at the normal T_c. The rubbery, amorphous nature of the PEO domains enhanced the gas permeability of the melt blends. In contrast, the constituent polymers maintained the bulk properties in 5–20 μm‐thick microlayers. The series model accurately described the gas transport properties of microlayered films. Comparison of blends and microlayers revealed that the high CO₂ selectivity of PEO was most effectively captured when the PEO phase was continuous, as in the microlayers or in the cocontinuous 50/50 (wt/wt) melt blend. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008.     

Surface modification of ethylene copolymers molded against different mold surfaces. Part 2. Changes at the outermost surface

The influence of the mold surface on the surface composition of thermoplastics has been investigated. Two different random copolymers, poly(ethylene-co-acrylic acid) (EAA) and poly(ethylene-co-vinyl acetate) (EVA), with varying comonomer contents were used. Specimens were prepared in molds coated with films of perfluorinated ethylene-propylene copolymer (FEP) and of poly(ethylene terephthalate) (PET). Samples were also molded against air and vacuum. Changes in the concentration and arrangement of the functional groups at the outermost surface were studied using X-ray photoelectron spectroscopy (XPS or ESCA), Fourier transform infra-red techniques (FTIR), and contact angle measurements. The concentration of functional groups at the outermost copolymer surface depended on the nature of the surface against which the random copolymers were molded. Results are interpreted in terms of differences in surface energy between the mold surface and the copolymer. The polar acrylic acid groups in EAA increased when molded against the polar PET mold surface and decreased when molded against nonpolar mold surfaces. Air exposure affected the EAA copolymer surface so that the nonpolar parts migrated to the outermost polymer surface, which resulted in a decreased content of acrylic acid groups. Acetate groups in EVA were found to be in excess at the surface when molded against both polar PET and nonpolar FEP. The signal of O 1s in the XPS spectra depended on the mold surface and the time in the XPS vacuum environment. This can be explained in terms of preferential arrangement of the acrylic acid and the vinyl acetate groups.     

Synthesis and monomer reactivity ratios of ethyl α‐acetoxyacrylate and acrylic acid copolymers

The synthesis of ethyl α‐acetoxyacrylate (EAA) and the study of its radical polymerization is described. We report the monomer reactivity ratios for copolymers of EAA and acrylic acid (AA) using three different methods: the Jaacks, the Macret and the Fineman–Ross methods. Copolymers were obtained by free radical polymerization initiated by 2,2′‐azobisisobutyronitrile in acetonitrile solutions and were analyzed by NMR and HPLC. The HPLC analysis was used to determine the molar fractions of EAA and AA in the copolymers. The reactivity ratios were estimated to be close to 1 for each monomer. Thus, copolymers of poly(acrylic acid) bearing some biodegradable units of EAA in the chain were subsequently prepared. The study of the hydrolysis of these units shows that only basic conditions were efficient to lead to hydrolyzed monomer units. Copyright © 2005 Society of Chemical Industry     

Novel ionomers based on blends of ethylene-acrylic acid copolymers with poly(vinyl amine)

The polymerization of N-vinyl formamide followed by hydrolysis yields a linear, water-soluble poly(vinyl amine). The high concentration of pendant primary amine groups leads to a polymer with an interesting set of properties. Complexation with water-soluble anionic polyelectrolytes in water solutions leads to a highly water-insoluble material. The study described herein investigated the phase behavior/properties of melt blends of poly(vinyl amine) with ethylene-acrylic acid (EAA) copolymers of less than 10 wt % acrylic acid. The calorimetric and dynamic mechanical analyses of the resultant blends show that the vinyl amine groups are accessible to the acrylic acid groups of the copolymers and the major property changes occur up to the stoichiometric addition of vinyl amine/acrylic acid. At higher levels of vinyl amine (vinyl amine/acrylic acid mol ratio > 4), additional poly(vinyl amine) forms a separate phase. The mechanical, dynamic mechanical, and calorimetric properties of these blends below the stoichiometric ratio show analogous trends as with typical alkali/alkaline metal neutralization. These characteristics relative to the base EAA include improved transparency, lower melting and crystallization temperature, lower level of crystallinity, and increased modulus and strength. The emergence of the β transition in dynamic mechanical testing is pronounced with these blends (as with alkali/alkaline metal neutralization), indicative of microphase separation of the amorphous phase into ionic-rich and ionic-depleted regions. A rubbery modulus plateau for the blends exists above the polyethylene melting point, demonstrating ionic crosslinking. Above 150°C exposure, further modulus increases occur presumably due to amide formation. This study demonstrates that the highly polar poly(vinyl amine) can interact with acrylic acid units in an EAA copolymer comprised predominately of polyethylene (>90 wt %). The thermodynamic driving force favoring ionic association overrides the highly unfavorable difference in composition. © 1996 John Wiley & Sons, Inc.     

Characterization of aqueous micellar solutions of amphiphilic block copolymers of poly(acrylic acid) and polystyrene prepared via ATRP. Toward the control of the number of particles in emulsion polymerization

A series of diblock, triblock and star-block copolymers composed of polystyrene and poly(acrylic acid) were synthesized by ATRP. The structure of the copolymers, the size of the blocks and the composition were varied, keeping however a short polystyrene block and a poly(acrylic acid) content larger than 60 mol% to allow solubility in alkaline water. Their micellization was studied by static and dynamic light scattering and the influence of their structural characteristics on the aggregation number, N_agg, was examined at low salt concentration and alkaline pH. It was shown that micelles were in thermodynamic equilibrium and that N_agg followed the power law N_agg∼N_A^−0.9N_S² (with N_A, the total number of acrylic acid units in the copolymer and N_S, the total number of styrene units), that is characteristic of amphiphile micelles formed from strongly segregated block copolymers. Moreover, N_agg was independent of salt concentration in the investigated range. The same copolymers were previously used as stabilizers in emulsion polymerization [Macromolecules 34 (2001) 4439]. The final latex particle concentration, N_p, was compared with N_m, the initial micelle concentration. This enabled us to conclude that among the block copolymers studied, those with high acid content behaved like low molar mass surfactants. In contrast, those with low acid content formed stable micelles that could be directly nucleated to create latex particles, allowing a good control over N_p.     

Surface modification of ethylene copolymers moulded against different mould surfaces-1. Surface enrichment by functional groups

A polymer surface chemical composition can be changed by the influence of different environments. Results presented from this study show that the surface of the mould influences the outermost polymer surface by enriching it with specific functional groups. This was done by moulding random copolymers against polymer films with low and high surface energies. The values presented are interpreted in terms of differences in surface energy between the mould surface and the copolymer. The random copolymers used were poly(ethylene-co-vinylacetate) (EVA) and poly(ethylene-co-acrylic acid) (EAA), both with a different comonomer content. The copolymers were moulded in contact with mould surfaces made of polymer films which were perfluorinated ethylene propylene copolymer (FEP), poly(tetrafluoroethylene) (PTFE), and poly(ethylene terephthalate) (PET). The resultant surfaces were characterized by X-ray photoelectron spectroscopy (XPS or ESCA) and contact angle measurements The surface content of acrylic acid functional groups increased in the case of EAA copolymer moulded against PET, and decreased when moulded against FEP as compared to the bulk concentration. EVA copolymers were found to be enriched in acetate groups when moulded against FEP and deficient when moulded against PET. The contact angle measurements together with the XPS measurements showed significant differences between materials moulded in contact with low and high energy surfaces. A low molecular weight additive (an internal release agent), in an EVA copolymer, was found to be enriched at the moulded polymer surface when a PET film was used as mould surface. A material transfer was also found to occur from the solid polymer films to the moulded polymer surface.     

Miscibility of poly(vinyl acetate) and vinyl acetate-ethylene copolymers with styrene-acrylic acid and acrylate-acrylic acid copolymers

Poly(vinyl acetate) and vinyl acetate-ethylene (VAE) copolymers compose one of the more important polymeric materials, widely employed in coating and adhesive applications. A new class of miscible polymer blends involving poly(vinyl acetate) and VAE with styrene-acrylic acid and acrylate-acrylic acid copolymers has been found. Experimental windows of miscibility as a function of the ethylene content for VAE copolymers and the acrylic acid content of the acrylate-acrylic acid copolymers are observed (acrylate = methyl acrylate, ethyl acrylate, n-butyl acrylate, and 2-ethylhexyl acrylate). Employing well-established analog heat of mixing measurements, predicted windows of miscibility were compared with experimental results. Fair qualitative agreement was observed and supported the hypothesis that specific rejection arguments can be employed to explain the observed miscibility. Failure to quantitatively predict miscibility based on the analog heat of mixing measurements may be due to the higher association tendencies of the model compounds relative to acrylic acid units in the high molecular weight polymers. No miscible combinations were found for methyl methacrylate-acrylic acid copolymers or acrylate-methacrylic acid copolymers in admixture with poly(vinyl acetate) or the VAE copolymers, thus indicating the sensitivity of phase behavior to minor structural changes. VAE (30 wt % ethylene) copolymers were also noted to be miscible with several polymers previously noted to be miscible with poly(vinyl acetate), namely, poly(vinylidene fluoride), poly(ethylene oxide), and nitrocellulose. © 1995 John Wiley & Sons, Inc.     

Interpolymer complexation between poly(ethylene oxide) and poly(acrylic acid)

Summary Solution and solid state properties of the interaction between poly(acrylic acid) and poly(ethylene oxide) have been studied in the presence and absence of CaSO₄ in water or in methanol systems. The association in solution has been investigated by viscosity measurements and NMR spectroscopy. The solid state of the systems has been studied using DSC, IR, X-RAY and 13-C-CPMAS-NMS. Complex formation is also clearly indicated.     

Physicomechanical studies and solvent resistance analysis of melt‐blended novel ethylene‐1‐octene elastomer and ethylene‐co‐acrylic acid interpenetrating network hybrids

Polar modification of poly(ethylene‐co‐octene) (POE) elastomer was carried out with a relatively new approach. Poly(ethylene‐co‐acrylic acid) (EAA) was taken as the modifier and POE with a calculated amount of EAA were coextruded with dicumyl peroxide (DCP; used as a crosslinker). The majority of the compositions showed the existence of a crosslinked EAA phase inside POE, although increasing DCP concentrations and extrusion temperatures were possibly capable of crosslinking either of the phases, as observed with a model composition. All of the samples were soft and light in nature. The best composition was the one that contained 13.3 wt % EAA; that composition showed excellent surface polarity and superior mechanical properties. Detailed solvent swelling experiments also yielded the best results for that particular composition. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Architectural effect of poly(acrylic acid) and poly(amide imide) block copolymers on dispersion of carbon nanotubes in water

The dispersion of carbon nanotubes (CNTs) in water by poly(acrylic acid) (PAA) and poly(amide imide) (PAI) block copolymers and homo‐PAA is investigated. Poly(acrylic acid)‐block‐poly(amide imide) (PAA‐block‐PAI), poly(acrylic acid)‐block‐poly(amide imide)‐block‐poly(acrylic acid) (PAA‐block‐PAI‐block‐PAA), and heteroarm star block copolymer poly(acrylic acid)₂poly(amide imide) (PAA₂PAI) with similar molecular weights and PAA contents are used as the copolymers. The dispersion of CNTs is observed by dynamic light scattering and ultraviolet‐visible spectroscopy. The presence of the hydrophobic sequence improves the dispersion. PAA₂PAI has the best dispersion ability, followed in order by PAA‐block‐PAI‐block‐PAA, PAA‐block‐PAI, and homo‐PAA. In the dry state, aggregates of CNT are observed by transmission electron microscopy (TEM) in the mixture with PAA‐block‐PAI and homo‐PAA. The adhesion of the copolymers to CNT is also observed by TEM and is due to the high affinity between hydrophobic PAI and CNT. In particular, PAA₂PAI and PAA‐block‐PAI‐block‐PAA well cover the CNTs. The presence of PAI and the PAA location are important for the dispersion of CNTs. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43461.     

Morphology and properties of nanocomposites formed from ethylene/methacrylic acid copolymers and organoclays

Nanocomposites were prepared by melt mixing ethylene/methacrylic acid copolymers and organoclays, which were compared to equivalent composites prepared from low-density polyethylene (LDPE) and a sodium ionomer of poly(ethylene-co-methacrylic acid). The effects of matrix modification and organoclay structure on the morphology and properties of these nanocomposites were evaluated using stress-strain analysis, wide-angle X-ray scattering (WAXS), and transmission electron microscopy coupled with particle analysis. With all four polymers, the use of a two-tailed organoclay, M₂(HT)₂, led to the formation of more exfoliated nanocomposites than a one-tailed organoclay, M₃(HT)₁. Nanocomposites prepared from ethylene/methacrylic acid copolymers revealed better exfoliation compared to similar composites prepared from LDPE. It seems that the presence of relatively small quantities (1.3-3.1 mol%) of the polar methacrylic acid monomer aids in improving the organoclay exfoliation efficiency of these polymers. Nanocomposites prepared from the sodium ionomer of poly(ethylene-co-methacrylic acid) exhibited the highest levels of organoclay exfoliation compared to all other polymers examined in this study. However, from the observations made in this study, it was not possible to determine conclusively the relative interaction of carboxyl acid groups versus the salt form with the organoclay and, thus, their influence on exfoliation; additional studies will be needed to reach a conclusion on this important point.     

Interpolymer complexes of novel linear and crosslinked acrylic acid–Schiff base copolymers

Novel linear and crosslinked copolymers of acrylic acid and Schiff base, containing the amine groups in the main chain and the carboxylic groups in the side chain, have been synthesized by the Michael addition reaction followed by radical copolymerization. The copolymers that exhibited poly(ampholyte–electrolyte) behaviour were used to prepare complexes by reaction with anionic (poly(acrylic acid), poly(styrene sodium sulfonate)), cationic (polyethyleneimine, poly(hexamethylene guanidine)) and non‐ionic (poly(N‐vinylpyrrolidone), poly(ethylene glycol), poly(vinyl alcohol)) polymers. The influence of external factors, such as solvent quality, temperature, pH and ionic strength, on phase (coil–globule) and volume (swelling–collapse) transitions has been studied. © 2003 Society of Chemical Industry     

Synthesis and aggregation behavior of four types of different shaped PCL‐PEG block copolymers

Biodegradable, amphiphilic, linear (diblock and triblock) and star‐shaped (three‐armed and four‐armed) poly[(ethylene glycol)‐block‐(ε‐caprolactone)] copolymers (PEG–PCL copolymers) were synthesized by ring‐opening polymerization of ε‐caprolactone (CL) with stannous octoate as a catalyst, in the presence of monomethoxypoly(ethylene glycol) (MPEG), poly(ethylene glycol) (PEG), three‐armed poly(ethylene glycol) (3‐arm PEG) or four‐armed poly(ethylene glycol) (4‐arm PEG) as an initiator, respectively. The monomer‐to‐initiator ratio was varied to obtain copolymers with various PEG weight fractions in a range 66–86%. The molecular structure and crystallinity of the copolymers, and their aggregation behavior in the aqueous phase, were investigated by employing ¹H‐NMR spectroscopy, gel permeation chromatography and differential scanning calorimetry, as well as utilizing the observational data of gel–sol transitions and aggregates in aqueous solutions. The aggregates of the PEG–PCL block copolymers were prepared by directly dissolving them in water or by employing precipitation/solvent evaporation technique. The enthalpy of fusion (ΔH_m), enthalpy of crystallization (ΔH_crys) and degrees of crystallinity (χ_c) of PEG blocks in copolymers and the copolymer aggregates in aqueous solutions were influenced by their PEG weight fractions and molecular architecture. The gel–sol transition properties of the PEG–PCL block copolymers were related to their concentrations, composition and molecular architecture. Copyright © 2006 Society of Chemical Industry